201e359 Handle early exit when addrstring isn't set
fa4c464 Improve address logging on early exit messages (#83)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
It seemed very confusing when trying to select the different variants of
hostapd which are somewhat scattered about under the menu 'Network'.
Moving all hostapd variants under a common submenu helps avoid
confusion.
Inspired-by: Kevin Mahoney <kevin.mahoney@zenotec.net>
[Fixup badly formatted patch, change menu name]
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
ab7a39a umdns: fix unused error
45c4953 dns: explicitly endian-convert all fields in header and question
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This reverts commit d7f21940bc.
Winbond W25Q256FV and W25Q256JV both uses 0xef4019 as JEDEC ID,
but only the latter has proper 4B_OPCODES support.
W25Q256FV has all 4B read instructions but it lacks a 4B page program
instruction, causing the entire flash to be read-only.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Missing config symbols could lead to build failures on kernel
4.14/4.19.
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
[rephrase commit message - reorder symbols]
Signed-off-by: David Bauer <mail@david-bauer.net>
gcc 8 & 9 appear to be more picky with regards access alignment to
packed structures, leading to this warning in dns.c:
dns.c:261:2: error: converting a packed ‘struct dns_question’ pointer
(alignment 1) to a ‘uint16_t’ {aka ‘short unsigned int’} pointer
(alignment 2) may result in an unaligned pointer value
[-Werror=address-of-packed-member]
261 | uint16_t *swap = (uint16_t *) q;
Work around what I think is a false positive by turning the warning off.
Not ideal, but not quite as not ideal as build failure.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Reduce unnecessary flash wear and be tidy:
- Run the extraction only if necessary
- Extract temporary file to /tmp
- cleanup after execution
Tested-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
In RTL8367B (RTL8367RB/RTL8367R-VB), the driver in GPL tars of the
devices with this switch directly uses the ID of external interface
as a bit offset.
We should use the same way.
ref (RTL8367B):
- ASUS RT-N56U
- TP-Link Archer C2 v1
ref (RTL8367):
- TP-Link TL-WR2543ND v1
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
DSA requires master netdev to be up before any of its slave ports.
Bring it up during preinit so that the first lan port can be used
on failsafe.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
It's unknown which switch port is used on mikrotik_rbm11g.
Disable this image until someone with actual device fixes this problem.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This script isn't suitable for mt7621 anymore due to switching to DSA
and it needs a different preinit script.
Generic preinit logic in package/base-files has the ability to parse
board.json and pick preinit iface accordingly. Just remove this script
instead of moving it into subtargets.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The 2nd gmac of mediatek soc ethernet may not be connected to a PHY
and a phy-handle isn't always available.
Unfortunately, mt7530 dsa driver assumes that the 2nd gmac is always
connected to switch port 5 and setup mt7530 according to phy address
of 2nd gmac node, causing null pointer dereferencing when phy-handle
isn't defined in dts.
This commit fix this setup code by checking return value of
of_parse_phandle before using it.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
LAN ports of MTC WR1201 are reversed, so correct their names
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
mt7621 SoC has its own 'ralink_soc_info' structure with some
information about the soc itself. Pcie controller and pcie phy
drivers for this soc which are still in staging git tree make uses
of 'soc_device_attribute' looking for revision 'E2' in order to
know if reset lines are or not inverted. This way of doing things
seems to be necessary in order to make things clean and properly.
Hence, introduce this 'soc_device' to be able to properly use those
attributes in drivers. Also set 'data' pointer points to the struct
'ralink_soc_info' to be able to export also current soc information
using this mechanism.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
The original idea of bitbanged I2C is to use i2c-gpio-custom
Since i2c-gpio-custom is no longer available on 5.4, use SoC I2C instead
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
The name of each user port should be eth0..4, instead of lan1..4
and there is no WAN port. Rename them to match the official firmware.
To avoid conflict with the master port (gmac0), rename it to "dsa".
The official firmware assigns MAC address in this way:
eth0 = label mac
eth1 = label mac + 1
...
eth4 = label mac + 4
Since we have switched to DSA, it's possible to use different MAC for each port.
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Most of MT7621 boards have LAN1~4 and WAN, so make this as the default
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
update dts and network/LED configuration for DSA driver.
sysupgrade from images prior to this commit with config preserved
will cause broken ethernet setup.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Acked-by: Jo-Philipp Wich <jo@mein.io>
[split commit]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
There's different gpio and ethernet drivers upstream for mt7621.
Update these two nodes to match upstream dt bindings.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Since commit f8c55dc ("MIPS: use generic dma noncoherent ops for
simple noncoherent platforms") changed MIPS dma handling, the mmc
driver fails because it doesn't have a dma mask is set.
So set the correct dma mask.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
1. Use functions for cleaner code
2. Always execute WAN interface generic code
Before this change WAN interface code wasn't executed on all devices due
to an early "exit 0".
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
add module to support Mellanox Connect-X card
mlx4 supports ConnectX-3 series and previous cards
mlx5 supports Connect-IB/ConnectX-4 series and later cards
Signed-off-by: Tan Zien <nabsdh9@gmail.com>
Specifying root filesystem by device is non-deterministic for several
reasons:
- USB device unmeration order is not garunteeed for USB storage devs
- MMC devs ordering is determined by the instance of the MMC host
controller including non-storage SDIO devices which can throw off
numbering depending on kernel versions.
It is recommended to use partition UUID
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
JSON info files contain machine readable information of built profiles
and resulting images. These files were added in commit 881ed09ee6
("build: create JSON files containing image info").
They are useful for firmware wizards and script checking for
reproducibility.
Currently all JSON files are stored next to the built images, resulting
in up to 168 individual files for the ath79/generic target.
This patch refactors the JSON creation to store individual per image
(not per profile) files in $(BUILD_DIR)/json_info_files and create an
single overview file called `profiles.json` in the target directory.
Storing per image files and not per profile solves the problem of
parallel file writes. If a profiles sysupgrade and factory image are
finished at the same time both processes would write to the same JSON
file, resulting in randomly broken outputs.
Some target like x86/64 do not use the image code yet, resulting in
missing JSON files. If no JSON info files were created, no
`profiles.json` files is created as it would be empty anyway.
As before, this creation is enabled by default only if `BUILDBOT` is set.
Tested via buildroot & ImageBuilder on ath79/generic, imx6 and x86/64.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[json_info_files dir handling in Make, if case refactoring]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Disable ASLR and filter '-fno-plt' from CFLAGS: solves building when
ASLR enabled by basically disabling ASLR.
Solves errors similar to:
relocation R_X86_64_32S against `.rodata' can not be used when making a PIE object; recompile with -fPIE
or
module missing GLOBAL_OFFSET_TABLE
Suggested-by: 李国 <uxgood.org@gmail.com>
Acked-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
