- add fxos8700 support to GW52xx/GW53xx/GW54xx
- add USB_OTG support to GW552x
- add LSM9DS1 IMU support to GW560x
- add LSM9DS1 IMU support to GW5904
- add CC1352 UART to GW5910
- add BCM4330 support to GW5910
- fix wlan regulator for GW5910
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
32-bit x86 fail to compile fast-math feature when compiled with frame
pointer, which uses a register used in a couple of inline asm functions.
Previous versions of wolfssl had this by default. Keeping an extra
register available may increase performance, so it's being restored for
all architectures.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This will be moved to packages:
https://github.com/openwrt/packages/pull/12378
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[commit subject facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Does not seem to be needed here. This will be imported into packages.
Ref: https://github.com/openwrt/packages/pull/12256
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[subject facelift, PR ref]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
No package in base uses libconfig. Everything is in the packages feed.
Ref: https://github.com/openwrt/packages/pull/12255
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[subject facelift, PR ref]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since commit 910df3f06c we have build in
on all X86/64 platforms the gpio-it87 driver.
Since this change I am getting the following error message on boot.
> kern.err kernel: [ 1.009416] gpio_it87: no device
I do not have this device on my system. To prevent the nonsensical
message and the loading of the module I have added this as a package, so
that it can be installed later or during image building.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
This is only a cosmetic correction, as the driver works as expected.
However, the error message confuses users about a missing reset definition.
On a defered init we don't see the following error message now:
[ 0.078292] ar7200-usb-phy usb-phy: phy reset is missing
Tested-by: Lech Perczak <lech.perczak@gmail.com>
Signed-off-by: Johann Neuhauser <johann@it-neuhauser.de>
Due to filesystem write caching the old configuration data could stay
out of flash for a long time during a first boot after the sysupgrade.
Power loss during this period could damage the overlay data and even
make device inaccessable via the network.
Fix this by syncing data to a flash as soon as the previous
configuration will be unpacked after the sysupgrade. Also sync the FS
state after the sysupgrade.tgz archive removing to prevent duplicative
extraction of a previous configuration.
Tested with AMD Geode based board.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
This commit removes changes from upstream commits:
8e18c8e58da6 arm64: dts: marvell: armada-3720-espressobin: declare SATA
PHY property
bd3d25b07342 arm64: dts: marvell: armada-37xx: link USB hosts with their
PHYs
For most boards which have factory bootloader this caused that devices
connected to USB 3.0 and SATA port were not detected. For them to
function users would need to upgrade the bootloader to version with ARM
Trusted Firmware 2.1 or later. Unfortunately there is no official
bootloader image with updated ATF component, therefore drop these
properties from nodes. This change was also tested briefly with
bootloader with updated ATF and the ports functioned properly.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Enable the disk-activity LED trigger for ipq806x, since this SoC has an
onboard SATA controller.
Signed-off-by: Thomas Albers <thomas.gameiro@googlemail.com>
[split into separate commit]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This changes the ide-disk LED trigger to the generic disk-activity as
ide-disk trigger was removed in upstream commit eb25cb9956cc ("leds:
convert IDE trigger to common disk trigger").
Signed-off-by: Thomas Albers <thomas.gameiro@googlemail.com>
[split into separate commit, commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Kernel config option LEDS_TRIGGER_IDE_DISK was renamed in kernel 4.8 to
CONFIG_LEDS_TRIGGER_DISK in upstream commit eb25cb9956cc ("leds: convert
IDE trigger to common disk trigger").
Removing it as it should be added only on targets which has usage for
this trigger.
Signed-off-by: Thomas Albers <thomas.gameiro@googlemail.com>
[commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The buildroot and SDK both require `libncurses-dev` to be installed on
the system, however the ImageBuilder uses precompiled binaries.
This patch changes the prerequirements checks to skip the
`libncurses-dev` part if running as ImageBuilder.
Signed-off-by: Paul Spooren <mail@aparcar.org>
ZyXEL Keenetic has a USB port. Thus, DWC2 USB controller driver should
be in the default image for this device.
Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[fixed whitespace issue]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
In FS#2738 we can see that patch first introduced in
e8ebcff ("ramips: add a explicit reset to dwc2")
breaks USB functionality since 18.06. Thus, this patch should be removed.
Removed:
- 0032-USB-dwc2-add-device_reset.patch
Fixes: FS#2738
Fixes: FS#2964
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
Required for installation of autoconf:
make[5]: Entering directory `/openwrt/build_dir/host/autoconf-2.69'
Making all in bin
make[6]: Entering directory `/openwrt/build_dir/host/autoconf-2.69/bin'
autom4te_perllibdir='..'/lib AUTOM4TE_CFG='../lib/autom4te.cfg'
../bin/autom4te -B '..'/lib -B '..'/lib --language M4sh --cache
'' --melt ./autoconf.as -o autoconf.in
Can't locate Data/Dumper.pm in @INC (@INC contains: ../lib
/usr/local/lib64/perl5 /usr/local/share/perl5 /usr/lib64/perl5/vendor_perl
/usr/share/perl5/vendor_perl /usr/lib64/perl5 /usr/share/perl5 .) at
../lib/Autom4te/C4che.pm line 33.
BEGIN failed--compilation aborted at ../lib/Autom4te/C4che.pm line 33.
Compilation failed in require at ../bin/autom4te line 40.
BEGIN failed--compilation aborted at ../bin/autom4te line 40.
make[6]: *** [autoconf.in] Error 2
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Since DEVICE_TYPE cannot be set per device, just set DEVICE_TYPE
to "nas" for the entire subtarget, which only contains this single
device.
Note that while this looks like a cosmetic change in combination
with the previous patches, this particular patch actually changes
the packages for the device.
Suggested-by: Christian Lamparter <chunkeey@gmail.com>
Cc: Christian Lamparter <chunkeey@gmail.com>
Cc: Sungbo Eo <mans0n@gorani.run>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While the effective "default" based on frequent use is "router", the
DEVICE_TYPE variable actually provides a "basic" configuration without
selecting any additional packages.
This is currently set up with the identifier "bootloader", which seems
to be not used at all. However, the only targets not using "router" or
"nas" are actually archs38 and arc770, which use their own value
"developerboard" for DEVICE_TYPE which seems to have been invented when
these targets where added. The latter is not implemented in target.mk,
though, and will fall back to the "basic" set of packages then.
So, to clean this up and make it more readable, let's just define a
DEVICE_TYPE "basic" and use it for the aforementioned cases.
Cc: Christian Lamparter <chunkeey@gmail.com>
Cc: Sungbo Eo <mans0n@gorani.run>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
DEVICE_TYPE is a target/subtarget variable, and it does not have
any effect when set in a device definition. It can only be set
in a target's or subtarget's Makefile.
Consequently, having it set anyway is misleading, so this drops
all cases.
This effectively reverts the following commits:
7a1497fd60 ("apm821xx: MBL: set DEVICE_TYPE to NAS")
5b4765c93a ("gemini: Classify Raidsonic NAS IB-4220-B as a NAS")
cdc6de460b ("gemini: D-Link DNS-313 is a NAS")
For the following commit, the variable was set when adding device
support:
27b2f0fc0f ("kirkwood: add support for Iomega Storcenter ix2-200")
Cc: Christian Lamparter <chunkeey@gmail.com>
Cc: Sungbo Eo <mans0n@gorani.run>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Some (older) CFEs are loaded at 0x80401000 and ramdisks are loaded at
0x80010000, which means that ramdisk size limit is 0x3F1000 (almost 4M).
Therefore, current ramdisks (~4MB) are overwritting CFE in these devices,
which results in a crash.
This commit changes the address where ramdisks are loaded to 0x80a00000,
which is the same address where kernel is loaded when booting from the flash.
Therefore, lzma-loader will now be loaded at 0x80a00000, but it will still
decompress the kernel at 0x80010000.
Tested with huawei,hg556a-b, which has its CFE loaded at 0x80401000.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Apparently, Sercomm allows loading a BCM WFI image via CFE, but this image
destroys "serial" and "protect" nand partitions, which is wrong.
It will also set both bootflags to the same value, which causes booting
issues with cferam (cferom will alternatively boot from cferam1 or cferam2
each time the device is rebooted).
Now that OEM Sercomm images are supported it's time to remove this hacky
cfe.bin image support.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
BCM6368 and newer devices are compatible with any lzma compression parameters.
Add a new legacy device definition and use it on BCM6358 and older devices.
Compressed kernel size is reduced by ~1.35%.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Allows to keep a backup firmware in case active firmware is corrupted.
Also fix hsspi address warning.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
When firmware is flashed, cferam.000 extension is renamed to the next number.
When booting, CFE scans the NAND and picks the partition with the highest
cferam extension and ignores the other one.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This images can be flashed from the official firmware, as opposed to CFE
images, which can only be flashed from CFE and require opening the case.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The only Sercomm WFI user has been migrated to a dedicated firmware parser.
Keep support for no cferam partition based on a boolean DT property.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Support Sercomm firmware partition split.
WFI partition must be defined after bootflag partitions in order for the
parser to properly find bootflag1 and bootflag2 partitions.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Sercomm uses 2 bootflag partitions and boots the firmware with the highest
bootflag. Support splitting the firmware partition while keeping support for
unsplitted layout.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Sercomm firmwares are encrypted with AES 256 CBC.
The key is generated with a custom algorithm from the firmware tag:
char key[32];
char version[32];
char iv[32];
char random[32];
char size[32];
Key must be generated with Sercomm's algorithm. However, the rest of the
header can be empty. IV and random are set to 0 on purpose.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
ddd57c2 pppd: Add lcp-echo-adaptive option
c319558 pppd: Handle SIGINT and SIGTERM during interrupted syscalls (#148)
0bc11fb Added missing options to manual pages. (#149)
b1fcf16 Merge branch 'monotonic-time' of https://github.com/themiron/ppp
c78e312 pppd: linux: use monotonic time if possible
Remove patch 121-debian_adaptive_lcp_echo as patch is upstream accepted
Remove patch 206-compensate_time_change.patch as timewrap issues are
solved by a patch making use of monotonic time
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
The TP-Link TL-MR3020 has a three-state mode slider which was previously
integrated as a button (EV_KEY). This led to spurious activations of
failsafe mode.
Set the type for the button to switch (EV_SW), to avoid unintended
activations of failsafe mode.
Related: commit 27f3f493de ("gpio-button-hotplug: unify polled and
interrupt code")
Signed-off-by: David Bauer <mail@david-bauer.net>
