eee02ccca8c8 device: add support to configure eee
bb28f6a291d9 wireless: fix sign comparison warning
35facc8306f5 wireless: fix premature removal of hotplug devices due to down state
Signed-off-by: Felix Fietkau <nbd@nbd.name>
841b05fbb91e system-linux: fix compilation error if IFLA_DSA_MASTER is not supported
5c9ecc1ff74f system-linux: make system_if_get_master_ifindex static
2dc7f450f3a2 system-linux: add option to configure DSA conduit device
838f815db5ef system-linux: add support for configurable GRO option
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently for 802.1s only, for wifi 2.4GHz in g/n mode, 40MHz is never
permitted.
This is probably due to the complexity of setting periodic check for the
intolerant bit. When noscan option is set, we ignore the presence of the
intoleran bit in near AP, so we can enable 40MHz and ignore any complex
logic for checking.
Fixes: #13112
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Also channel 7 for 2.4GHz can be set to HT40PLUS. Permit this and add it
to the list of the channels.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
noscan option for mesh was broken and actually never applied.
This is caused by a typo where ssid->noscan value is check instead of
conf->noscan resulting in the logic swapped and broken.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
383753dd65ae device/bridge: support passing extra vlans in the device_set_state call
b6e75eafc1af device: send notifications for device events via ubus
cab415c7aefd bridge: add auth-required bridge members with auth_status=0 if vlan is enabled
827a02f0343c bridge: add support for configuring vlans for auth=1,auth_status=false
40ed7363caf2 device: fix build error on 32 bit systems
516ab774cc16 system-linux: fix race condition on bringing up wireless devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
4101dd4 fw4: perform strict validation of zone and set names
a923c88 fw4: pass zone to templates whenever possible
597dc90 fw4: add support for zone log_limit
1874050 fw4: add log_limit to rules and redirects
19a8caf ruleset: dispatch ct states using verdict map
a5553da ruleset: reduce ksoftirqd load by refering to looopback by numeric id
de3483c tests: adjust zone log limit testcases
7392792 ruleset: do not emit redundant drop invalid rules
698a533 ruleset: apply egress MSS fixup later to apply final MTU before wire
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It's already pulled in from /etc/rc.common.
Fixes: #13758
Fixes: 6b23836071 ("package: avoid the use of eval to parse ipcalc.sh output")
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Upgrading wpa_supplicant from 2.9 to 2.10 breaks broadcom-wl/ath11k
based adapters. The reason for it is hostapd tries to install additional
IEs for scanning while the driver does not support this.
The kernel indicates the maximum number of bytes for additional scan IEs
using the NL80211_ATTR_MAX_SCAN_IE_LEN attribute. Save this value and
only add additional scan IEs in case the driver can accommodate these
additional IEs.
Bug: http://lists.infradead.org/pipermail/hostap/2022-January/040178.html
Bug-Debian: https://bugs.debian.org/1004524
Bug-ArchLinux: https://bugs.archlinux.org/task/73495
Upstream-Status: Changes Requested [https://patchwork.ozlabs.org/project/hostap/patch/20220130192200.10883-1-mail@david-bauer.net]
Reported-by: Étienne Morice <neon.emorice@mail.com>
Tested-by: Étienne Morice <neon.emorice@mail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The code for hostapd-mbedtls did not work when used for OWE association.
When handling association requests, the buffer offsets and length
assumptions were incorrect, leading to never calculating the y point,
thus denying association.
Also when crafting the association response, the buffer contained the
trailing key-type.
Fix up both issues to adhere to the specification and make
hostapd-mbedtls work with the OWE security type.
Signed-off-by: David Bauer <mail@david-bauer.net>
Configure the PLMN and APN to the modem. This is required in cases,
where either the SGSN or GGSN does not permit the selection of IPv4v6
pdp type.
Previously, the modem always tried to establish a dual-stacked PDP
context regardless of the configured PDP type in uci. As this setting
can not be parameterized when creating a WDS context, configure it to
the modems internal list of profiles. This way, the PDP type is taken
into account when creating the WDS context.
Signed-off-by: David Bauer <mail@david-bauer.net>
The PLMN selection was reset when calling network-register, thus
rendering the sepcific selection of a carrier unapplied.
Set the PLMN selection after executing network-register. This seems to
cause the modem to re-select the carrier eventually.
That being said, qmi does allow the parameterization of the
network-register to include dpecific PLMN settings, however this is
currently not implemented in uqmi.
Signed-off-by: David Bauer <mail@david-bauer.net>
Set the RAT preference before attaching. This handles cases better,
where a network might be available but not with the preferred RAT.
If RAT is changed to a non-available RAT after attach, QMI does not fail
with missing registration but with failing to establish a PDP session.
Signed-off-by: David Bauer <mail@david-bauer.net>
Increase the wait time before polling the connection state for the first
time.
Depending on the prior state of the modem, the first poll might still
return a connected state. The script then tries to establish a PDP
session, which subsequently fails as the modem by then is in scan state.
Increasing the wait-time to 3 seconds mitigates this from happening.
Signed-off-by: David Bauer <mail@david-bauer.net>
On some network-triggered disconnections the UIM state might end up in
"illegal". This prevents the modem from attaching to any network in
non-restricted service modes.
Detect this state and reset the SIM card. This way, the modem can attach
to networks again.
Signed-off-by: David Bauer <mail@david-bauer.net>
Failing the registration does not necessarily mean we can not bring this
interface up. For example, roaming SIM cards are possibly steered by the
home-operator.
Don't block restart of the QMI interface in this case.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes building with USE_LTO enabled.
<artificial>:(.text+0xc22): relocation R_MIPS16_26 against `libxt_DNAT_init' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol printf
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
This fixes building with USE_LTO enabled.
<artificial>:(.text+0x400c): relocation R_MIPS16_26 against `iwinfo_close' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol strcpy
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
d8118f6 config: make sure timer is not on the timeouts list before freeing
4bbc6e7 add hostsfile output in addition to statefile
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
c8c9f10 uim: fix help formatting
aac0776 uqmi: add APN profile commands
ffc5eea uim: support SIM card power-up/down
d6c963d uim: add application state to SIM status
Signed-off-by: David Bauer <mail@david-bauer.net>
The option 31 in the RA specifies the DNS search list, the support
to configure this via UCI is missing in case dnsmasq-dhcpv6 is used.
This commit uses the uci option domain (same as is done by odhcpd) to
read and pass the DNS search list to dnsmasq, which is then used by RA.
Hence, with this commit, we are able to configure DNS search list for the
RA messages via the uci config when dnsmsaq-dhcpv6 is used.
Signed-off-by: Rahul Thakur <rahul.thakur@iopsys.eu>
479c7f8676d9 cache: make record/hostname lookup case-insensitive
26c97a5a50bf ubus: add a browse flag for suppressing cached ip addresses
c286c51a9bd9 Fix AVL tree traversal in cache_record_find and cache_host_is_known
4035fe42df58 interface: use a global socket instead of per-interface ones
c63d465698c7 cache: dump hostname target from srv records
b42b22152d73 use hostname from SRV record to look up IP addresses
d45c443aa1e6 ubus: add array flag support for the hosts method
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There are a few targets that mess with the atm kernel headers. To avoid
incompatibility between kernel and user space during compilation, the
correct headers should be used.
Consequently, the package must also be marked as nonshared.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Modems which are using qmi do not reply on the 1st sync but they do
on subsequent. So qmi.sh is hanging on the first call. Since 2020 uqmi
supports a timeout parameter. Unfortunately qmi.sh didn't make use of
this parameter. So qmi.sh is now invoking an early dummy access to
unlock the modem
Signed-off-by: Uwe Niethammer <uwe@dr-niethammer.de>
Recent hostapd changes just edited the ucode files. It is required to
bump the PKG_RELEASE to include the newest changes in the latest builds.
Signed-off-by: Nick Hainke <vincent@systemli.org>
If the full interface is restarted while bringing up an AP, it can trigger a
wpa_supplicant interface start before wpa_supplicant is notified of the
allocated mac addresses.
Fix this by moving the iface_update_supplicant_macaddr call to just after
the point where mac addresses are allocated.
Reported-by: Michael-cy Lee (李峻宇) <Michael-cy.Lee@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In the dnsmasq init script, an off-by-one in the range calculation of
ipcalc.sh was mitigated by passing the limit as if its counting started
at zero. This patch removes the mitigation as the off-by-one has been
fixed.
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Add a function 'ipcalc' to /lib/functions.sh that sets variables more
safely using export.
With this new function, dnsmasq also handles the return value of ipcalc
correctly.
Fixes: e4bd3de1be ("dnsmasq: refuse to add empty DHCP range")
Co-Authored-By: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
allow to overwrite the detected system capabilities e.g. if devices
does not operate as bridge.
Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
The patch refresh accidentally moved the hostapd_ucode_free_iface call to
the wrong function
Fixes: e9722aef9e ("hostapd: fix a crash when disabling an interface during channel list update")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The PKG_CPE_ID links to NIST CPE version 2.2.
Assign PKG_CPE_ID to all remaining package which have a CPE ID.
Not every package has CPE id.
Related: https://github.com/openwrt/packages/issues/8534
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
