Increase QDMA RESV_BUF from 2K to 3K for netsys v2 to match Mediatek SDK.
This helps reduce the possibility of Ethernet transmit timeouts.
Link: 19d8456c30
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The purpose of resetting the TX queue is to reset the
byte and packet count as well as to clear the software
flow control XOFF bit.
MediaTek developers pointed out that netdev_reset_queue would only
resets queue 0 of the network device.
Queues that are not reset may cause unexpected issues.
Packets may stop being sent after reset and "transmit timeout" log may
be displayed.
Import fix from MediaTek's SDK to resolve this issue.
Link: 5746a94456
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The previous host installation fix accidentally moved the rpath settings
out of CMAKE_HOST_OPTIONS and into CMAKE_OPTIONS.
Fixes: ae42ecaad4 ("ucode: fix host installation")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Drop config and files for Linux 5.15.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16417
Signed-off-by: Robert Marko <robimarko@gmail.com>
Drop config and files for Linux 5.15.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16417
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for netis N6 WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (ESMT PSU1GA30DT)
- WLAN : MT7905DAN + MT7975DN
- 2.4 GHz : b/g/n/ax, 574 Mbps, MIMO 2x2
- 5 GHz : a/n/ac/ax, 1201 Mbps, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x5 (1x WAN, 4x LAN)
- USB : 1x 3.0
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
1x WPS
- LEDs : 1x Power (green)
1x System (green)
1x WAN (green)
1x WiFi 2.4 GHz (green), controlled by phy
1x WiFi 5 GHz (green), controlled by phy
1x WPS (green)
1x USB (green)
5x ethernet leds (green), controlled by switch
- Power : 12 VDC, 1.5 A
Installation
------------
1. Update the router using stock firmware web interface and OpenWrt
factory.bin image.
Recovery and return to stock
----------------------------
1. Assign your PC a static IP 192.168.1.2 and connect to the router using
the ethernet cable;
2. Power off the router;
3. Press Reset button, power on the router and wait until ethernet led
start blinking;
4. Release the button;
5. Open http://192.168.1.1/ (N6 System Recovery Mode) in your browser;
6. Upload OpenWrt factory.bin (or stock firmware *.bin) image and proceed
with upgrade.
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LAN | dc:xx:xx:49:xx:04 |
| WAN | dc:xx:xx:49:xx:05 |
| WLAN 2g | dc:xx:xx:19:xx:06 |
| WLAN 5g | dc:xx:xx:79:xx:06 |
+---------+-------------------+
The WLAN MAC prototype was found in 'Factory', 0x4
The LAN MAC was found in 'Factory', 0x7ef20
The WAN MAC was found in 'Factory', 0x7ef26
Known issue
-----------
2.4 GHz WLAN doesn't start with mt76 driver.
Probable reason:
Original Netis N6 EEPROM contains wrong MT_EE_WIFI_CONF value (0xd2).
Other routers with the same WLAN hardware (e.g., Routerich AX1800)
have MT_EE_WIFI_CONF = 0x92.
Workaround (already included in this commit):
Extract EEPROM to a file at the first time boot and change
MT_EE_WIFI_CONF (offset 0x190) value from 0xd2 to 0x92. See
/etc/hotplug.d/firmware/11-mt76-caldata for details.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This files are executable:
target/linux/ramips/dts/mt7621_openfi_5pro.dts
target/linux/ramips/dts/mt7621_winstars_ws-wn536p3.dts
Has to be fixed.
Fixes: 5560791 ("ramips: add support for OpenFi 5Pro Travel Router")
Fixes: 2da2705 ("ramips: add support for WINSTARS WS-WN536P3")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of reading it from flash directly, let U-Boot assign the LAN
MAC address. Set label-mac-device while at it and sort aliases in DT
alphabetically.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kconfig symbols CONFIG_VIDEO_MICROCHIP_CSI2DC, CONFIG_VIDEO_MICROCHIP_ISC
and CONFIG_VIDEO_MICROCHIP_XISC are missing for sama5 and sama7 causing
the build to abort or waiting for user input. Add the symbols (disabled)
so build with Linux 6.6 succeeds.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix a typo in the MAC address assignment script affecting SDG-8734.
Fixes: c71b68acdd ("mediatek: filogic: add Adtran SmartRG Mount Stuart series")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that we copy and then delete the Per-Device rootfs linux directory,
it's not valid anymore placing the generated cpio there as artifacts
or subsequent commands need the generated cpio.
To handle this, rework Initramfs compile cpio handling by placing them in
the KERNEL_BUILD_DIR but add to the name the rootfs HASH ID.
To also prevent race condition, generate and access these file under a
lock to prevent fit command to reference a cpio while a parallel
execution is genereting it.
Fixes: 52cc9d82f1 ("kernel: rework Initramfs locking logic")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix flock name for gen-initramfs lock as $(2) starts with .HASH making
the lock name gen-initramfs-.HASH.flock
Fix this to a better name of gen-initramfs.HASH.flock
Fixes: 52cc9d82f1 ("kernel: rework Initramfs locking logic")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix wrong rework for Initramfs cpio xz compression where it was wrongly
dropped the Per-Device linux directory if condition.
Fixes: 52cc9d82f1 ("kernel: rework Initramfs locking logic")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Hardware information:
---------------------
- SoC: RTL8393M
- Copper phy: 6×RTL8218B
- Fibre phy: RTL8214FC
- Flash: 32MiB SPI NOR, MX25L25635FMI
- RAM: 128MiB DDR3, Micron MT41K64M16TW-107
- Serial port: ±5V serial port to RJ45, ZT3232 (MAX3232 compatible)
- +370W POE on JG928A model
Note: SFP ports currently non-functional due to missing support for
RTL8214FC on the RTL8393M target.
Updated for Linux 6.6 kernel.
Installation:
-------------
- Initial installation follows same process as HPE 1920-24G (JG924A)
- Based on prior work of Jan Hoffmann <jan@3e8.eu>
- Additional work by Andreas Böhler <dev@aboehler.at>
- PoE updates and tidy-up by Stephen Howell <howels@allthatwemight.be>
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
Now that there is 6.6 support for realtek, lets encourage testing it by
making it default so 5.15 can be dropped ASAP.
Link: https://github.com/openwrt/openwrt/pull/16408
Signed-off-by: Robert Marko <robimarko@gmail.com>
The 'active-low' property was not applied correctly and two fixes
are required to make inverted LEDs work as expected.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
bcc091d session: Fix crash when the UCI option 'password' or 'username' is missing
9f4b86e rpcd: iwinfo: add IEEE 802.11be support
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for 802.11be (HE) radios.
4b7c47c iwinfo: sync with upstream nl80211.h
268a662 iwinfo: add basic IEEE 802.11be support
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The at91 now supports 6.6 kernel as testing.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Remove obsolete patches no longer applicable to the 6.6 kernel.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Remove unnecessary dts files already included in the 6.1 kernel.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/16058
Signed-off-by: Nick Hainke <vincent@systemli.org>
Siflower SF19A2890 is an SoC with:
Dual-core MIPS InterAptiv at 800MHz
DDR3 controller
One Gigabit Ethernet MAC with RGMII and IPv4 HNAT engine
Built-in 2x2 11N + 2x2 11AC WiFi radio
USB 2.0 OTG
I2C/SPI/GPIO and various other peripherals
This PR adds support for SF19A2890 EVB with ethernet support.
EVB spec:
Memory: DDR3 128M
Ethernet: RTL8367RB 5-port gigabit switch
Flash: 16M NOR
Others: MicroUSB OTG, LED x 1, Reset button x1
The built image can be flashed using u-boot recovery.
This target is marked as source-only until support for a commercial
router board comes.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The busybox built with mips16 enabled has broken seq command.
Disassembling shows that the call to hard-float strtod in mips16
code is generated without the __call_stub_fp:
```
0x00406d6f <+118>: lw v0,32(sp)
0x00406d71 <+120>: sll s0,2
0x00406d73 <+122>: addu s0,v0,s0
0x00406d75 <+124>: lw a0,-4(s0)
0x00406d79 <+128>: jal 0x44ebc1 <strtod@mips16plt>
0x00406d7d <+132>: addiu a1,sp,84
0x00406d7f <+134>: sw v0,64(sp)
0x00406d81 <+136>: lw v0,0(s1)
0x00406d83 <+138>: sw v1,68(sp)
```
As a result, strtod returns the result in float point registers
while the calling mips16 code expect the result in v0/v1.
Disable mips16 on hard-float targets for now. The built .ipk goes
from 213316 bytes to 251419 bytes.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This fixes a well-known "LZMA ERROR 1" error on Sercomm NA502s, reported
on the OpneWrt forum [0].
[0] https://forum.openwrt.org/t/206640
Signed-off-by: Andreas Böhler <dev@aboehler.at>
To speedup compilation of Per-Device Initramfs, copy the kernel build
directory for each rootfs ID.
This permits concurrent execution of kernel build without conflicting
with each other at the expense of additional disk space usage.
To limit disk space usage, the copied kernel directory is deleted after
the Per-Device Initramfs image is generated and saved.
Link: https://github.com/openwrt/openwrt/pull/16404
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Rework CompileImage/Initramfs locking logic to fix race condition on
concurrent access/compilation.
Rework each intermediate step and group them under one single execution
block. Protect this with a new lock, 'gen-initramfs' and rename the
compile initramfs to compile-initramfs lock name.
This is done to handle corner case scenario where a rootfs with the same
hash ID is generated at the same time. To handle this, we execute
everything under lock and use a specific hash ID lock to prevent
concurrent access/compilation.
Link: https://github.com/openwrt/openwrt/pull/16404
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
RELR is a relocation packing format for relative relocations.
Linux has supported using it for ARM64 since 5.4, and more recently
for LoongArch as well.
It requires compatible tooling as well, so only with binutils 2.43
TOOLS_SUPPORT_RELR is set and thus RELR available.
RELR should always decrease the binary size and while testing this
the default build for Dynalink WRX-36 (qualcommax/ipq807x) reduced
the compressed kernel size by 38k and uncompressed one by 640k.
So, lets enable it in the default config.
Link: https://github.com/openwrt/openwrt/pull/16403
Signed-off-by: Robert Marko <robimarko@gmail.com>
Merging of the realtek 6.6 series forgot to include some final fixes
for the new MDIO driver. What was changed in last second?
1. The MDIO driver used wrong constants to make use of the raw
page (for direct register access). Provide a rawpage variable in
the bus private structure, populate it during initialization and
make use of it at the proper places
2. We always used the variable portaddr for the bus index. Usually
our driver uses either addr or port for the same meaning. Remove the
duplication and reuse the normal addr variable.
3. Drop functions rtmdio_write_page() and rtmdio_read_page(). These
only call the PHY driver read/write page functions. We know that
these will only access page 0x1f. As we have only Realtek PHYs
and our driver only reacts to this special page, just hardcode it.
Benefit is that we can use these functions for PHY detection when
read/write page functions are not yet assigned.
4. Add two new helper functions phy_port_read_paged() and
phy_port_write_paged(). These allow to access arbitrary ports on
the MDIO bus when the packages are not initialized. These will be
needed for proper RTL8218B and RTL8214FC detection in forthcoming
patches.
5. The port tracking wrongly used index 0 to mark "normal" access.
This does not allow to make a "special" access to port 0. Use
index -1 to mark "normal" access.
Provide the fix for 5.15 and 6.6 to allow for easy version
comparison.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
With commit a22d359fa5 VLAN handling was fixed for kernel 6.6.
This restored network connectivity of the devices. For easy testing
backport the fix for 5.15 too.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
On the XGS1210-12 the RTL8218D is attached via XGMII. Add this to the
supported list in the DSA driver.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16391
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove upstreamed from 2.11 release:
060-nl80211-fix-crash-when-adding-an-interface-fails.patch
Rebase all other patches
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16338
Signed-off-by: Robert Marko <robimarko@gmail.com>
Release 2.11 has been quite a few new features and fixes since the 2.10
release. The following ChangeLog entries highlight some of the main
changes:
* Wi-Fi Easy Connect
- add support for DPP release 3
- allow Configurator parameters to be provided during config exchange
* HE/IEEE 802.11ax/Wi-Fi 6
- various fixes
* EHT/IEEE 802.11be/Wi-Fi 7
- add preliminary support
* SAE: add support for fetching the password from a RADIUS server
* support OpenSSL 3.0 API changes
* support background radar detection and CAC with some additional
drivers
* support RADIUS ACL/PSK check during 4-way handshake (wpa_psk_radius=3)
* EAP-SIM/AKA: support IMSI privacy
* improve 4-way handshake operations
- use Secure=1 in message 3 during PTK rekeying
...and many more
Remove upstreamed patches:
023-ndisc_snoop-call-dl_list_del-before-freeing-ipv6-add.patch
030-driver_nl80211-rewrite-neigh-code-to-not-depend-on-l.patch
040-mesh-allow-processing-authentication-frames-in-block.patch
181-driver_nl80211-update-drv-ifindex-on-removing-the-fi.patch
182-nl80211-move-nl80211_put_freq_params-call-outside-of.patch
183-hostapd-cancel-channel_list_update_timeout-in-hostap.patch
210-build-de-duplicate-_DIRS-before-calling-mkdir.patch
253-qos_map_set_without_interworking.patch
751-qos_map_ignore_when_unsupported.patch
800-SAE-Check-for-invalid-Rejected-Groups-element-length.patch
801-SAE-Check-for-invalid-Rejected-Groups-element-length.patch
802-SAE-Reject-invalid-Rejected-Groups-element-in-the-pa.patch
Other patches has been updated.
Signed-off-by: Ivan Pavlov <AuthorReflex@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16338
Signed-off-by: Robert Marko <robimarko@gmail.com>
