Add 5.15 kernel as a testing kernel version in the Makefile.
Linksys EA6350v3/EA8300/MR8300 will not build with buildbot settings and
should be disabled when the target is switched, unless the image size is
reduced again.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
[add comment for increased kernel size]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Kernel 5.15 have some new api for ethtool and phy.
Add ifdef to fix compilation error.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Robert Marko <robert.marko@sartura.hr>
The 2.4GHz interface doesn't come up properly with the log showing:
mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
As seen on other MT7621 boards this is caused by a missing reset GPIO.
The MT7621 dtsi set GPIO 19 as PCIe reset GPIO, which on this board
reset the 5GHz interface on port 0. Add GPIO 8 to the PCIe reset GPIO
list to also reset the 2.4GHz interface on port 1.
Signed-off-by: Alban Bedel <albeu@free.fr>
Refreshed patches:
- 100-cross_compile.patch
Manually refreshed patches:
- 200-reduce_size.patch
Removed patches:
- 101-mdadm.h-Undefine-dprintf-before-redefining.patch
- 102-Add-missing-include-file-sys-sysmacros.h.patch
Changes:
e30ca260 Release mdadm-4.2
8c80d305 Monitor: print message before quit for no array to monitor
ced5fa8b mdadm: block creation with long names
b71de056 Correct checking if file descriptors are valid
b2e4f084 Incremental: Close unclosed mdfd in IncrementalScan()
195d1d76 imsm: assert if there is migration but prev_map doesn't exist
75f3ba25 imsm: free allocated memory in imsm_fix_size_mismatch
bce0eab3 Release mdadm-4.2-rc3
4389ce73 imsm: introduce helpers to manage file descriptors
8e1a258e mdadm/Detail: Can't show container name correctly when unpluging disks
a35aa68f mdadm/lib: Define a new helper function is_dev_alived
1c66260d Fix 2 dc stream buffer
d64a37b9 Assemble: apply sysfs rules
5f6dedfb Fix potential overlap dest buffer
a0422106 disallow create or grow clustered bitmap with writemostly set
cf16a350 Fix buffer size warning for strcpy
60815698 Refactor parse_num and use it to parse optarg.
f7889e51 Fix error message when creating raid 4, 5 and 10
54604768 mdadm: fix coredump of mdadm --monitor -r
feeb2785 Utils: Change sprintf to snprintf
b8bbf264 Release mdadm-4.2-rc2
e6878148 Assemble: skip devices that don't match uuid instead of aborting the assembly.
0663137c Add monitor delay parameter to mdadm.conf
2b2c5668 tests: Avoid passing chunk size when creating RAID 1
7d374a18 Fix memory leak after "mdadm --detail"
92a647c8 Assemble: start dirty and degraded array.
1c275381 imsm: fix num_data_stripes after raid0 takeover
5b30a34a Add error handling for chunk size in RAID1
3a85bf0e imsm: Fix possible memory leaks and refactor freeing struct dl
ccd61ebf mdadm: Fix building errors
601ffa78 Don't associate spares with other arrays during RAID Examine
8d69bf14 Remove Spare drives line from details for external metadata
7d8935cb imsm: correct offset for 4k disks in --examine output
dca80fcd Use dev_open in validate geometry container
f421731c mdadm/super1: It needs to specify int32 for bitmap_offset
1f5d54a0 Manage: Call validate_geometry when adding drive to external container
8662f92d imsm: Limit support to the lowest namespace
fcebeb77 imsm: add devpath_to_char method
7c798f87 imsm: add generic method to resolve "device" links
0530e2e0 Prevent user from using --stop with ambiguous args
83b3de77 Fix some building errors
ff904202 imsm: change wrong size verification
c11b1c3c Release mdadm-4.2-rc1
aec01630 super-intel.c: Handle errors from calls to get_dev_sector_size()
78c93b00 mdadm: fix growing containers
af3396da Monitor: make libudev dependency optional
f94df5cf imsm: support for third Sata controller
d835518b imsm: nvme multipath support
4036e7ee imsm: extend curr_migr_unit to u64
bdbe7f81 Grow: Block reshape when external metadata and write-intent bitmap
848d71c9 Create: Block automatic enabling bitmap for external metadata
19ad203e imsm: Update-subarray for write-intent bitmap
dc95f821 Add "bitmap" to allowed command-line values
69d40de4 imsm: Adding a spare to an existing array with bitmap
fbc42556 imsm: Write-intent bitmap support
b554ab5c Enable bitmap support for external metadata
b090e910 Modify mdstat parsing for volumes with the bitmap
db537788 It should be FAILED when raid has not enough active disks
c7b8547c imsm: add verbose flag to compare_super
49b69533 mdmonitor: check if udev has finished events processing
0d583954 Document PPL in man md
2f86fda3 imsm: use saved fds during migration
f7a6246b super1.c: avoid useless sync when bitmap switches from clustered to none
e6561c4d super1: fix Floating point exception
8818d4e7 Grow: be careful of corrupt dev_roles list
4ae96c80 mdadm: fix reshape from RAID5 to RAID6 with backup file
1fe2e100 mdadm/bitmap: locate bitmap calcuate bitmap position wrongly
75562b57 Dump: get stat from a wrong metadata file when restoring metadata
69068584 Incremental: Remove redundant spare movement logic
a64f1263 udev: start grow service automatically
b4a5ad49 Make target to install binaries only
9c030dad mdadm/Detail: show correct state for clustered array
ff6bb131 mdadm: Unify forks behaviour
a8f3cfd5 imsm: limit support to first NVMe namespace
ca4b156b Monitor: don't use default modes when creating a file
b65c1f4a imsm: remove redundant calls to imsm_get_map
895ffd99 imsm: update num_data_stripes according to dev_size
ce559078 Create.c: close mdfd and generate uevent
c3129b39 Detail: fix segfault during IMSM raid creation
97b51a2c Super1: allow RAID0 layout setting to be removed.
7f3b2d1d Check if other Monitor instance running before fork.
cab9c67d mdmonitor: set small delay once
007087d0 Monitor: stop notifing about containers.
e2308733 Monitor: refresh mdstat fd after select
2ce09172 Don't create bitmap for raid5 with journal disk
64bf4dff Detail: show correct raid level when the array is inactive
5f418455 manual: update --examine-badblocks
5e592e1e mdadm/md.4: update path to in-kernel-tree documentation
138a9e9b Specify nodes number when updating cluster nodes
77b72fa8 mdadm/Grow: prevent md's fd from being occupied during delayed time
bcf40dbb Update link to Intel page for IMSM
8e41153c Use more secure HTTPS URLs
2cf04330 Detect too-small device: error rather than underflow/crash
7758ada9 Block overwriting existing links while manual assembly
d92cee7b restripe: fix ignoring return value of ‘read’ and lseek
7d90f760 Include count for \0 character when using strncpy to implement strdup.
f4c8a605 uuid.c: split uuid stuffs from util.c
03ab9763 Makefile: add EXTRAVERSION support
3b7aae92 mdcheck: Log when done
7b99edab Assemble.c: respect force flag.
ec7d7cee clean up meaning of small typo
5cfb79de Assemble: print error message if mdadm fails assembling with --uuid option
12724c01 Manage, imsm: Write metadata before add
1c294b5d Detail: adding sync status for cluster device
185ec439 Monitor: improve check_one_sharer() for checking duplicated process
e1b92ee0 udev: Ignore change event for imsm
ba1b3bc8 imsm: show Subarray and Volume ID in --examine output
e48aed3c imsm: support the Array Creation Time field in metadata
9e449405 Detail: show correct bitmap info for cluster raid device
06a6101c imsm: Correct minimal device size.
45c43276 imsm: Remove --dump/--restore implementation
3364781b imsm: pass subarray id to kill_subarray function
fd38b8ea Remove the legacy whitespace
2551061c mdadm.8: add note information for raid0 growing operation
1e93d0d1 imsm: fill working_disks according to metadata.
42e641ab Add support for Tebibytes
4431efeb imsm: Update grow manual.
e1512e7b mdcheck service can't start succesfully because of syntax error
1a874930 Change warning message
aced6fc9 Respect $(CROSS_COMPILE) when $(CC) is the default
027c099f Assemble: add support for RAID0 layouts.
329dfc28 Create: add support for RAID0 layouts.
6da53c0e imsm: Change the way of printing nvme drives in detail-platform.
b771faef imsm: return correct uuid for volume in detail
4b31846f Remove unused code
9cf361f8 Fix up a few formatting issues
02af3793 Remove last traces of HOT_ADD_DISK
1cc3965d Manage: Remove the legacy code for md driver prior to 0.90.03
761e3bd9 super-intel: don't mark structs 'packed' unnecessarily
85b83a79 SUSE-mdadm_env.sh: handle MDADM_CHECK_DURATION
4ca799c5 mdcheck: use ${} to pass variable to mdcheck
6636788a mdcheck: when mdcheck_start is enabled, enable mdcheck_continue too.
1a1ced1e imsm: allow to specify second volume size
b6180160 imsm: save current_vol number
7bd59e79 udev: allow for udev attribute reading bug.
61109314 Don't need to check recovery after re-add when no I/O writes to raid
8063fd0f Init devlist as an array
e53cb968 mdadm/md.4: add the descriptions for bitmap sysfs nodes
2c2d9c48 mdadm: force a uuid swap on big endian
43ebc910 mdadm: Introduce new array state 'broken' for raid0/linear
fd5b09c9 mdadm: check value returned by snprintf against errors
91c97c54 imsm: close removed drive fd.
1a52f1fc udev: add --no-devices option for calling 'mdadm --detail'
d11abe4b mdadm: add --no-devices to avoid component devices detail information
452dc4d1 mdadm.h: include sysmacros.h unconditionally
b0681598 mdadm: load default sysfs attributes after assemblation
486720e0 super-intel: Use put_unaligned in split_ull
7039d1f8 mdadm.h: Introduced unaligned {get,put}_unaligned{16,32}()
a4f7290c super-intel: Fix issue with abs() being irrelevant
4ec389e3 Enable probe_roms to scan more than 6 roms.
ae7d61e3 mdmon: fix wrong array state when disk fails during mdmon startup
3c9b46cf udev: Add udev rules to create by-partuuid for md device
22dc741f Create: Block rounding size to max
05501181 imsm: fix spare activation for old matrix arrays
227aeaa8 add missing units to --examine
2b57e4fe Assemble: Fix starting array with initial reshape checkpoint
d2e11da4 mdmon: wait for previous mdmon to exit during takeover
69d08478 mdmon: don't attempt to manage new arrays when terminating
76b906d2 mdadm/tests: add one test case for failfast of raid1
cab114c5 Fix reshape for decreasing data offset
e3615ecb Detail.c: do not skip first character when calling xstrdup in Detail()
ebf3be99 Fix spelling typos.
9f421827 imsm: fix reshape for >2TB drives
a4e96fd8 imsm: finish recovery when drive with rebuild fails
757e5543 policy.c: Fix for compiler error
467e6a1b policy.c: prevent NULL pointer referencing
76d505de Grow: report correct new chunk size.
085df422 Grow: avoid overflow in compute_backup_blocks()
563ac108 Assemble: mask FAILFAST and WRITEMOSTLY flags when finding the most recent device
d7a1fda2 imsm: update metadata correctly while raid10 double degradation
7cd7e91a Monitor: add system timer to run --oneshot periodically
4199d3c6 mdcheck: add systemd unit files to run mdcheck.
cd72f9d1 policy: support devices with multiple paths.
6b611284 Document PART-POLICY lines
0833f9c3 Assemble: keep MD_DISK_FAILFAST and MD_DISK_WRITEMOSTLY flag
Signed-off-by: Nick Hainke <vincent@systemli.org>
We don't need to make sure that we want to have enabled
CONFIG_CMD_SETEXPR by default, since this is already done in U-boot [1].
This was actually needed only for clearfog board [2], which was added in
commit: da0005a6d08ae33d958a6d8a6c0c12dc07b5b2b8 ("uboot-mvebu: add
patch to enable setexpr for clearfog boards) and send to U-boot to fix
it properly. After a while, there was added support for Turris Omnia,
which uses setexpr as well [3], but for this board, there are no fixes
needed in U-boot and that's why we can remove this option here.
It is helpful with shell scripting. If some downstream distributions are
using it, they should correct it in defconfig for related boards.
[1] e95afa5675/cmd/Kconfig (L1504)
[2] 852126680e/target/linux/mvebu/image/clearfog.bootscript (L7)
[3] 852126680e/target/linux/mvebu/image/turris-omnia.bootscript (L2)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Option CMD_SETEXPR is already default in U-boot [1], since this was
disabled since initial version for this board, there is send this
patch to U-boot mailing list to enable it.
It is required to use in OpenWrt bootscript for these boards [2].
[1] e95afa5675/cmd/Kconfig (L1504)
[2] 852126680e/target/linux/mvebu/image/clearfog.bootscript (L7)
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
SoC: Atheros AR7161
RAM: DDR 128 MiB (hynix h5dU5162ETR-E3C)
Flash: SPI-NOR 8 MiB (mx25l6406em2i-12g)
WLAN: 2.4/5 GHz
2.4 GHz: Atheros AR9220
5 GHz: Atheros AR9223
Ethernet: 4x 10/100/1000 Mbps (Atheros AR8021)
LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin)
UART: RJ45 9600,8N1
Power: 12 VDC, 1.0 A
Installation instruction:
0. Make sure you have latest original firmware (3.7.11.4)
1. Connect to the Serial Port with a Serial Cable RJ45 to DB9/RS232
(9600,8N1)
screen /dev/ttyUSB0 9600,cs8,-parenb,-cstopb,-hupcl,-crtscts,clocal
2. Configure your IP-Address to 192.168.1.42
3. When device boots hit spacebar
3. Configure the device for tftpboot
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.42
saveenv
4. Reset the device
reset
5. Hit again the spacebar
6. Now load the image via tftp:
tftpboot 0x81000000 INITRAMFS.bin
7. Boot the image:
bootm 0x81000000
8. Copy the squashfs-image to the device.
9. Do a sysupgrade.
https://openwrt.org/toh/netgear/wndap360
The device should be converted from kmod-owl-loader to nvmem-cells in the
future. Nvmem cells were not working. Maybe ATH9K_PCI_NO_EEPROM is missing.
That is why this commit is still using kmod-owl-loader. In the future
the device tree may look like this:
&ath9k0 {
nvmem-cells = <&macaddr_art_120c>, <&cal_art_1000>;
nvmem-cell-names = "mac-address", "calibration";
};
&ath9k1 {
nvmem-cells = <&macaddr_art_520c>, <&cal_art_5000>;
nvmem-cell-names = "mac-address", "calibration";
};
&art {
...
cal_art_1000: cal@1000 {
reg = <0x1000 0xeb8>;
};
cal_art_5000: cal@5000 {
reg = <0x5000 0xeb8>;
};
};
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add USB power control in DTS for GL.iNet models:
- AR300M;
- AR300M-Ext;
- AR300M16;
- AR300M16-Ext.
Signed-off-by: PtilopsisLeucotis <PtilopsisLeucotis@yandex.com>
This commit adds support for the TP-Link Deco M4R (it can also be M4,
TP-Link uses both names) v1 and v2. It is similar hardware-wise to the
Archer C6 v2. Software-wise it is very different. V2 has a bit different
layout from V1 but the chips are the same and the OEM firmware is the same
for both versions.
Specifications:
SoC: QCA9563-AL3A
RAM: Zentel A3R1GE40JBF
Wireless 2.4GHz: QCA9563-AL3A (main SoC)
Wireless 5GHz: QCA9886
Ethernet Switch: QCA8337N-AL3C
Flash: 16 MB SPI NOR
Flashing:
The device's bootloader only accepts images that are signed using
TP-Link's RSA key, therefore this way of flashing is not possible. The
device has a web GUI that should be accessible after setting up the device
using the app (it requires the app to set it up first because the web GUI
asks for the TP-Link account password) but for unknown reasons, the web
GUI also refuses custom images.
There is a debug firmware image that has been shared on the device's
OpenWrt forum thread that has telnet unlocked, which the bootloader will
accept because it is signed. It can be used to transfer an OpenWrt image
file over to the device and then be used with mtd to flash the device.
Pre-requisites:
- Debug firmware.
- A way of transferring the file to the router, you can use an FTP server
as an example.
- Set a static IP of 192.168.0.2/255.255.255.0 on your computer.
- OpenWrt image.
Installation:
- Unplug your router and turn it upside down. Using a long and thin object
like a SIM unlock tool, press and hold the reset button on the router and
replug it. Keep holding it until the LED flashes yellow.
- Open 192.168.0.1. You should see the bootloader recovery's webpage.
Choose the debug firmware that you downloaded and flash it. Wait until the
router reboots (at this stage you can remove the static IP).
- Open a terminal window and connect to the router via telnet (the primary
router should have a 192.168.0.1 IP address, secondary routers are
different).
- Transfer the file over to the router, you can use curl to download it
from the internet (use the insecure flag and make sure your source accepts
insecure downloads) or from an FTP server.
- The router's default mtd partition scheme has kernel and rootfs
separated. We can use dd to split the OpenWrt image file and flash it with
mtd:
dd if=openwrt.bin of=kernel.bin skip=0 count=8192 bs=256
dd if=openwrt.bin of=rootfs.bin skip=8192 bs=256
- Once the images are ready, you have to flash the device using mtd
(make sure to flash the correct partitions or you may be left with a
hard bricked router):
mtd write kernel.bin kernel
mtd write rootfs.bin rootfs
- Flashing is done, reboot the device now.
Signed-off-by: Foica David <superh552@gmail.com>
The Wavlink WL-WN533A8 is an AC3000 router with 5 gigabit ethernet ports
and one USB 3.0 port.
It's also known as Wavlink QUANTUM T8.
Hardware
--------
SoC: Mediatek MT7621A
RAM: 128MB (Nanya NT5CB64M16GP-EK)
FLASH: 16MB NOR (GigaDevice GD25Q127CSIG3)
ETH:
- 5x 10/100/1000 Mbps Ethernet (4x LAN + 1x WAN)
WIFI:
- 1x MT7615DN (2x 2x2:2) 2.4GHz and 5GHz DBDC
- 1x MT7615NE (4x4:4) 5GHz
- 8 external antennas
BTN:
- 1x Reset button
- 1x WPS button
- 1x Turbo button
- 1x Touchlink button
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 7x Blue leds (wifi led + 5 ethernet ports + power)
USB:
- 1x USB 3.0 port
UART:
- 57600-8-N-1
J4
Everything works correctly.
Installation
------------
Flash the initramfs image in the OEM firmware interface
(http://192.168.10.1/update.shtml).
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
(Procedure tested on fw M33A8.V5030.190716 and M33A8.V5030.201204)
Restore OEM Firmware
--------------------
Flash the firmware update available online directly from LUCI.
You can download it from:
https://www.wavlink.com/en_us/firmware/details/f2d247ecba.html
Warning: Remember to not keep settings!
Warning2: Remember to force the flash.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:63 (factory @ 0xe006)
WAN XX:XX:XX:XX:XX:64 (factory @ 0xe000)
WIFI 2G/5G XX:XX:XX:XX:XX:65 (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:66 (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:65
In OEM firmware the DBDC wifi interfaces have these mac addresses:
2G) 82:XX:XX:XX:XX:65
5G) 80:XX:XX:XX:XX:65
While in OpenWrt the addresses are:
2G) 80:XX:XX:XX:XX:65
5G) 02:XX:XX:XX:XX:65
2) radio0 will show as 2G/5G interface but only 2G is really usable.
3) There is just one wifi led for all wifi interfaces.
It currently shows only the radio0 GHz wifi activity.
4) My unit was shipped with M33A8.V5030.190716 firmware which contains
the http://192.168.10.1/webcmd.shtml page. Entering "telnetd" in
the input box it will start the telnet daemon. Now you can access
the telnet console on port 2323 with these credentials:
username: admin2860
password: admin
5) The M33A8.V5030.201204 firmware version, doesn't contain anymore the
webcmd.shtml page. If your router is shipped with a previous firmware
version and you want to back it up, you can follow the back up
procedure of the WS-WN583A6.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Most of the definitions for WN531A6 will be shared with WN533A8 in a
future commit, so put them in a shared DTSI.
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
In commit 7e614820a8 ("mpc85xx: add support for Extreme Networks
WS-AP3825i"), we borrowed a recipe convention from apm821xx for device
tree blob padding. Unfortunately, in the apm821xx target, the image
recipes name the device tree blob differently, meaning that in
mpc85xx, the padded dtb is never consumed.
Change the definition of `Build/dtb` so that it outputs the padded dtb
to the correct location for it to be consumed.
Also, rename the recipe to `Build/pad-dtb`, so it is clear we
are building and padding the device tree blob.
This change fixes Github issue #9779 [1].
[1]: https://github.com/openwrt/openwrt/issues/9779
Fixes: 7e614820a8 ("mpc85xx: add support for Extreme Networks WS-AP3825i")
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
targetclean should not remove BUILD_LOG
Fixes: db34b93331 (add a version that can be bumped to force toolchain/target rebuild)
Signed-off-by: Huangbin Zhan <zhanhb88@gmail.com>
The config for LEDS_UBNT_LEDBAR doesn't stay in mt7629 kconfig because
of its I2C dependency. Build it as a module and let buildroot handle
this config option instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Disable support for joysticks, micee and tablets. There's no actual
driver selected in kconfig, and including kernel support is just a
waste of space. Besides that, I believe nobody wants these on a router.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Remove patches and configuration for Linux 5.10 which have been left
in the tree despite the target having been switched to Linux 5.15.
Fixes: c283defa88 ("mediatek: switch to 5.15")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Set CONFIG_SCHED_MC in config-5.15 to have make the scheduler aware
of shared caches.
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ubiblock devices should be used on NAND flash to store the uImage.FIT
in case the bootloader supports that -- otherwise only rootfs is stored
in UBI while the uImage.FIT contains only the kernel and dtb.
Hence there is no need to enable parsing partitions on NAND mtdblock
devices, it is even responsible for the ugly warning on-opening of the
mtdblock device now. Just don't do it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of warning loudly about mtdblock devices being created, rather
just warn if they are actually used.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Last attempt on this has a typo and doen't work.
It seems that this is a common problem occurring on every kernel bump,
so let's enforce arch timer support for mt7623 with a patch instead.
Fixes: 9a22943eb2 ("mediatek: 5.15: re-enable arch timer on MT7623 as well")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This commit is completely based on the work of adron-s:
https://github.com/openwrt/openwrt/pull/4721#issuecomment-1101108651
The commit fixes the data corruption on TX packets. Packets are
transmitted, but their contents are replaced with zeros. This error is
caused by the lack of guard (50 ms) intervals between calibration phases.
This error is treated by adding mdelay(50) to the calibration function
code. In the original qca-ssda code [0], these mdelays were existing, but
in the ar41xx.c they are gone.
Tested on:
- Fritz!Box 4040
- Fritz!Box 7530
- Mikrotik SXTsq 5AC
- ZyXEL NBG6617
- [0] https://git.codelinaro.org/clo/qsdk/oss/lklm/qca-ssdk/-/blob/NHSS.QSDK.11.4/src/init/ssdk_init.c#L2072
Suggested-by: Serhii Serhieiev <adron@mstnt.com>
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Nick Hainke <vincent@systemli.org>
the SPI-NAND driver switch breaks dts compatibility. It's too much work
to backport all ECC framework support to 5.10 so let's switch the target
to 5.15 instead.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This patch implements the spi-nand controller driver as an ECC-capable
spi-mem controller to use the upstream SPI-NAND driver.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
the OOB layout in MTK SNFI uses the 2nd byte, and anything using OOB
will make the block a bad-block in spi-nand driver.
Hack it for now. We need a proper solution upstream.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Includes image support for new TP-Link devices:
ddc3e00e314d tplink-safeloader: add TP-Link EAP265 HD support
ceea1a7fe56e tplink-safeloader: add TP-Link Deco M4R v1 and v2 support
Signed-off-by: Sander Vanheule <sander@svanheule.net>
95ca1c3 nat46-core: ignore IPv4 options when translating packets
39778c2 add a module argument to ignore TOS translate for IPv4
9a36ee1 add a module argument to ignore TOS translate for IPv4
79190a8 add a module argument to ignore TOS translate for IPv4
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
