mirror of
https://github.com/openwrt/openwrt.git
synced 2024-12-27 01:11:14 +00:00
8ac8c09f5e
51 Commits
| Author | SHA1 | Message | Date | |
|---|---|---|---|---|
Bjørn Mork
|
8ac8c09f5e |
ipq40xx: sysupgrade: drop disabled UBI to UBI logic
The commented out code is not required, as the comment indicates. The purpose of this code seems to be to avoid issues caused by partially overwriting an existing UBI partition, where some of the erase counters would be reset but not the unmodified ones. This problem has been solved in a more generic way by the UBI EOF marker. This ensures that any old PEBs after the marker are properly initialized. It is therefore unnecessary to erase the whole partition before flashing a new OpenWrt factory image. Signed-off-by: Bjørn Mork <bjorn@mork.no> |
||
TruongSinh Tran-Nguyen
|
febc2b831f
|
ipq40xx: add support for GL.iNet GL-B2200
This patch adds supports for the GL-B2200 router. Specifications: - SOC: Qualcomm IPQ4019 ARM Quad-Core - RAM: 512 MiB - Flash: 16 MiB NOR - SPI0 - EMMC: 8GB EMMC - ETH: Qualcomm QCA8075 - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2 - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2 - WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2 - INPUT: Reset, WPS - LED: Power, Internet - UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 - UART2: On board with BLE module - SPI1: On board socket for Zigbee module Update firmware instructions: Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at https://docs.gl-inet.com/en/3/troubleshooting/debrick/). Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware. Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first. What's working: - WiFi 2G, 5G - WPA2/WPA3 Not tested: - Bluetooth LE/Zigbee Credits goes to the original authors of this patch. V1->V2: - updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake) - add uboot-envtools support V2->V3: - Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface V3->V4: - wire up sysupgrade Signed-off-by: Li Zhang <li.zhang@gl-inet.com> [fix tab and trailing space, document what's working and what's not] Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro> [rebase on top of master, address remaining comments] Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> [remove redundant check in platform.sh] Signed-off-by: Daniel Golle <daniel@makrotopia.org> |
||
Alexander Couzens
|
8d62304785
|
ipq40xx: add MikroTik LHGG-60ad outdoor 802.11ad (60GHz) dish
LHGG-60ad is IPQ4019 + wil6210 based. Specification: - Qualcomm IPQ4019 (717 MHz) - 256 MB of RAM (DDR3L) - 16 MB (SPI NOR) of flash - 1x Gbit ethernet, 802.3af/at POE IN connected through AR8035. - WLAN: wil6210 802.11ad PCI card - No USB or SD card ports - UART disabled - 8x LEDs Biggest news is the wil6210 PCI card. Integration for its configuration and detection has already been taken care of when adding support for TP-Link Talon AD7200. However, signal quality is much lower than with stock firmware, so probably additional board-specific data has to be provided to the driver and is still missing at the moment. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Daniel Golle <daniel@makrotopia.org> [Fix Ethernet Interface] Signed-off-by: Nick Hainke <vincent@systemli.org> |
||
Felix Matouschek
|
1cc3b95efc |
ipq40xx: Add support for Teltonika RUTX10
This patch adds support for the Teltonika RUTX10. This device is an industrial DIN-rail router with 4 ethernet ports, 2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs. The RUTX series devices are very similiar so common parts of the DTS are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev board. See https://teltonika-networks.com/product/rutx10 for more info. Hardware: SoC: Qualcomm IPQ4018 RAM: 256MB DDR3 SPI Flash 1: XTX XT25F128B (16MB, NOR) SPI Flash 2: XTX XT26G02AWS (256MB, NAND) Ethernet: Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n Wifi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac USB Hub: Genesys Logic GL852GT Bluetooth: Qualcomm CSR8510 (A10U) LED/GPIO controller: STM32F030 with custom firmware Buttons: Reset button Leds: Power (green, cannot be controlled) WiFi 2.4G activity (green) WiFi 5G activity (green) MACs Details verified with the stock firmware: eth0: Partition 0:CONFIG Offset: 0x0 eth1: = eth0 + 1 radio0 (2.4 GHz): = eth0 + 2 radio1 (5.0 GHz): = eth0 + 3 Label MAC address is from eth0. The LED/GPIO controller needs a separate kernel driver to function. The driver was extracted from the Teltonika GPL sources and can be found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt USB detection of the bluetooth interface is sometimes a bit flaky. When not detected power cycle the device. When the bluetooth interface was detected properly it can be used with bluez / bluetoothctl. Flash instructions via stock web interface (sysupgrade based): 1. Set PC to fixed ip address 192.168.1.100 2. Push reset button and power on the device 3. Open u-boot HTTP recovery at http://192.168.1.1 4. Upload latest stock firmware and wait until the device is rebooted 5. Open stock web interface at http://192.168.1.1 6. Set some password so the web interface is happy 7. Go to firmware upgrade settings 8. Choose openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi 9. Set 'Keep settings' to off 10. Click update, when warned that it is not a signed image proceed Return to stock firmware: 1. Set PC to fixed ip address 192.168.1.100 2. Push reset button and power on the device 3. Open u-boot HTTP recovery at http://192.168.1.1 4. Upload latest stock firmware and wait until the device is rebooted Note: The DTS expects OpenWrt to be running from the second rootfs partition. u-boot on these devices hot-patches the DTS so running from the first rootfs partition should also be possible. If you want to be save follow the instructions above. u-boot HTTP recovery restores the device so that when flashing OpenWrt from stock firmware it is flashed to the second rootfs partition and the DTS matches. Signed-off-by: Felix Matouschek <felix@matouschek.org> |
||
Robert Marko
|
3ad229db0b |
ipq40xx: add support for MikroTik hAP ac3
This adds support for the MikroTik RouterBOARD RBD53iG-5HacD2HnD (hAP ac³), a indoor dual band, dual-radio 802.11ac wireless AP with external omnidirectional antennae, USB port, five 10/100/1000 Mbps Ethernet ports and PoE passthrough. See https://mikrotik.com/product/hap_ac3 for more info. Specifications: - SoC: Qualcomm Atheros IPQ4019 - RAM: 256 MB - Storage: 16 MB NOR + 128 MB NAND - Wireless: · Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae · Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi antennae - Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port, passive PoE in, PoE passtrough on port 5 - 1x USB Type A port Installation: 1. Boot the initramfs image via TFTP 2. Run "cat /proc/mtd" and look for "ubi" partition mtd device number, ex. "mtd1" 3. Use ubiformat to remove MikroTik specific UBI volumes * Detach the UBI partition by running: "ubidetach -d 0" * Format the partition by running: "ubiformat /dev/mtdN -y" Replace mtdN with the correct mtd index from step 2. 3. Flash the sysupgrade image using "sysupgrade -n" Signed-off-by: Robert Marko <robimarko@gmail.com> Tested-by: Mark Birss <markbirss@gmail.com> Tested-by: Michael Büchler <michael.buechler@posteo.net> Tested-by: Alex Tomkins <tomkins@darkzone.net> |
||
Richard Yu
|
12d33d388c |
ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0)
P&W R619AC is a IPQ4019 Dual-Band AC1200 router. It is made by P&W (p2w-tech.com) known as P&W R619AC but marketed and sold more popularly as G-DOCK 2.0. Specification: * SOC: Qualcomm Atheros IPQ4019 (717 MHz) * RAM: 512 MiB * Flash: 16 MiB (NOR) + 128 MiB (NAND) * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) * Wireless: - 2.4 GHz b/g/n Qualcomm Atheros IPQ4019 - 5 GHz a/n/ac Qualcomm Atheros IPQ4019 * USB: 1 x USB 3.0 * LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED) * Input: 1 x reset * 1 x MicroSD card slot * Serial console: 115200bps, pinheader J2 on PCB * Power: DC 12V 2A * 1 x Unpopulated mPCIe Slot (see below how to connect it) * 1 x Unpopulated Sim Card Slot Installation: 1. Access to tty console via UART serial 2. Enter failsafe mode and mount rootfs <https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset> 3. Edit inittab to enable shell on tty console `sed -i 's/#ttyM/ttyM/' /etc/inittab` 4. Reboot and upload `-nand-factory.bin` to the router (using wget) 5. Use `sysupgrade` command to install Another installation method is to hijack the upgrade server domain of stock firmware, because it's using insecure http. This commit is based on @LGA1150(at GitHub)'s work < |
||
Davide Fioravanti
|
2cb24b3f3c |
ipq40xx: add support for Netgear SRR60/SRS60 and RBR50/RBS50
The Netgear SRS60 and SRR60 (sold together as SRK60) are two almost
identical AC3000 routers. The SRR60 has one port labeled as wan while
the SRS60 not. The RBR50 and RBS50 (sold together as RBK50) have a
different external shape but they have an USB 2.0 port on the back.
This patch has been tested only on SRS60 and RBR50, but should work
on SRR60 and RBS50.
Hardware
--------
SoC: Qualcomm IPQ4019 (717 MHz, 4 cores 4 threads)
RAM: 512MB DDR3
FLASH: 4GB EMMC
ETH:
- 3x 10/100/1000 Mbps Ethernet
- 1x 10/100/1000 Mbps Ethernet (WAN)
WIFI:
- 2.4GHz: 1x IPQ4019 (2x2:2)
- 5GHz: 1x IPQ4019 (2x2:2)
- 5GHz: 1x QCA9984 (4x4:4)
- 6 internal antennas
BTN:
- 1x Reset button
- 1x Sync button
- 1x ON/OFF button
LEDS:
- 8 leds controlled by TLC59208F (they can be switched on/off
independendently but the color can by changed by GPIOs)
- 1x Red led (Power)
- 1x Green led (Power)
UART:
- 115200-8-N-1
Everything works correctly.
Installation
------------
These routers have a dual partition system. However this firmware works
only on boot partition 1 and the OEM web interface will always flash on
the partition currently not booted.
The following steps will use the SRS60 firmware, but you have to chose
the right firmware for your router.
There are 2 ways to install Openwrt the first time:
1) Using NMRPflash
1. Download nmrpflash (https://github.com/jclehner/nmrpflash)
2. Put the openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img
file in the same folder of the nmrpflash executable
3. Connect your pc to the router using the port near the power button.
4. Run "nmrpflash -i XXX -f openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img".
Replace XXX with your network interface (can be identified by
running "nmrpflash -L")
5. Power on the router and wait for the flash to complete. After about
a minute the router should boot directly to Openwrt. If nothing
happens try to reboot the router. If you have problems flashing
try to set "10.164.183.253" as your computer IP address
2) Without NMRPflash
The OEM web interface will always flash on the partition currently not
booted, so to flash OpenWrt for the first time you have to switch to
boot partition 2 and then flash the factory image directly from the OEM
web interface.
To switch on partition 2 you have to enable telnet first:
1. Go to http://192.168.1.250/debug.htm and check "Enable Telnet".
2. Connect through telent ("telnet 192.168.1.250") and login using
admin/password.
To read the current boot_part:
artmtd -r boot_part
To write the new boot_part:
artmtd -w boot_part 02
Then reboot the router and then check again the current booted
partition
Now that you are on boot partition 2 you can flash the factory Openwrt
image directly from the OEM web interface.
Restore OEM Firmware
--------------------
1. Download the stock firmware from official netgear support.
2. Follow the nmrpflash procedure like above, using the official
Netgear firmware (for example SRS60-V2.2.1.210.img)
nmrpflash -i XXX -f SRS60-V2.2.1.210.img
Notes
-----
1) You can check and edit the boot partition in the Uboot shell using
the UART connection.
"boot_partition_show" shows the current boot partition
"boot_partition_set 1" sets the current boot partition to 1
2) Router mac addresses:
LAN XX:XX:XX:XX:XX:69
WAN XX:XX:XX:XX:XX:6a
WIFI 2G XX:XX:XX:XX:XX:69
WIFI 5G XX:XX:XX:XX:XX:6b
WIFI 5G (2nd) XX:XX:XX:XX:XX:6c
LABEL XX:XX:XX:XX:XX:69
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[added 5.10 changes for 901-arm-boot-add-dts-files.patch, moved
sysupgrade mmc.sh to here and renamed it, various dtsi changes]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
||
|
Robert Marko
|
b126d9c3a3 |
ipq40xx: add netgear wac510 support
This adds support for the Netgear WAC510 Insight Managed Smart Cloud Wireless Access Point, an indoor dual-band, dual-radio 802.11ac business-class wireless AP with integrated omnidirectional antennae and two 10/100/1000 Mbps Ethernet ports. For more information see: <https://www.netgear.com/business/wifi/access-points/wac510> Specifications: SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB Flash1: 2 MiB Winbond W25Q16JV SPI-NOR Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port, WAN port active IEEE 802.3af/at PoE in Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1 LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN Serial: Header J2 1 - 3.3 Volt (Do NOT connect!) 2 - TX 3 - RX 4 - Ground WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter! The Serial settings are 115200-8-N-1. Installation via Stock Web Interface: BTW: The default factory console/web interface login user/password are admin/password. In the web interface navigating to Management - Maintenance - Upgrade - 'Firmware Upgrade' will show you what is currently installed e.g.: Manage Firmware Current Firmware Version: V5.0.10.2 Backup Firmware Version: V1.2.5.11 Under 'Upgrade Options' choose Local (alternatively SFTP would be available) then click/select 'Browse File' on the right side, choose openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar and hit the Upgrade button below. After a minute or two your browser should indicate completion printing 'Firmware update complete.' and 'Rebooting AP...'. Note that OpenWrt will use the WAN PoE port as actual WAN port defaulting to DHCP client but NOT allowing LuCI access, use LAN port defaulting to 192.168.1.1/24 to access LuCI. Installation via TFTP Requiring Serial U-Boot Access: Connect to the device's serial port and hit any key to stop autoboot. Upload and boot the initramfs based OpenWrt image as follows: (IPQ40xx) # setenv serverip 192.168.1.1 (IPQ40xx) # setenv ipaddr 192.168.1.2 (IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb (IPQ40xx) # bootm Note: This only runs OpenWrt from RAM and has not installed anything to flash as of yet. One may permanently install OpenWrt as follows: Check the MTD device number of the active partition: root@OpenWrt:/# dmesg | grep 'set to be root filesystem' [ 1.010084] mtd: device 9 (rootfs) set to be root filesystem Upload the factory image ending with .ubi to /tmp (e.g. using scp or tftp). Then flash the image as follows (substituting the 9 in mtd9 below with whatever number reported above): root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi And reboot. Dual Image Configuration: The default U-Boot boot command bootipq uses the U-Boot environment variables primary/secondary to decide which image to boot. E.g. primary=0, secondary=3800000 uses rootfs while primary=3800000, secondary=0 uses rootfs_1. Switching their values changes the active partition. E.g. from within U-Boot: (IPQ40xx) # setenv primary 0 (IPQ40xx) # setenv secondary 3800000 (IPQ40xx) # saveenv Or from a OpenWrt userspace serial/SSH console: fw_setenv primary 0 fw_setenv secondary 3800000 Note that if you install two copies of OpenWrt then each will have its independent configuration not like when switching partitions on the stock firmware. BTW: The kernel log shows which boot partition is active: [ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB) vs. [ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB) Note: After 3 failed boot attempts it automatically switches partition. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> [squashed netgear-tar commit into main and rename netgear-tar for now, until it is made generic.] Signed-off-by: Christian Lamparter <chunkeey@gmail.com> |
||
Roger Pueyo Centelles
|
d1f1e5269e |
ipq40xx: add support for MikroTik SXTsq 5 ac
This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD), an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet port. Specifications: - SoC: Qualcomm Atheros IPQ4018 - RAM: 256 MB - Storage: 16 MB NOR - Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae - Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in - 1x Ethernet LED (green) - 7x user-controllable LEDs · 1x power (blue) · 1x user (green) · 5x rssi (green) Note: Serial UART is probably available on the board, but it has not been tested. Flashing: Boot via TFTP the initramfs image. Then, upload a sysupgrade image via SSH and flash it normally. More info at the "Common procedures for MikroTik products" page https://openwrt.org/toh/mikrotik/common. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net> |
||
|
Robert Marko
|
faea7becaf
|
ipq40xx: add MikroTik hAP ac2 support
This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC (hAP ac²), a indoor dual band, dual-radio 802.11ac wireless AP with integrated omnidirectional antennae, USB port and five 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/hap_ac2 for more info. Specifications: - SoC: Qualcomm Atheros IPQ4018 - RAM: 128 MB - Storage: 16 MB NOR - Wireless: · Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae · Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port, passive PoE in - 1x USB Type A port Installation: Boot the initramfs image via TFTP and then flash the sysupgrade image using "sysupgrade -n" Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
Dongming Han
|
b9389186b0 |
ipq40xx: add support for GL.iNet GL-AP1300
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
FLASH1: 4 MiB NOR
FLASH2: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: Reset
LED: Power, Internet
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
OTHER: On board with BLE module - by cp210x USB serial chip
On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed
Install via uboot tftp or uboot web failsafe.
By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi
(IPQ40xx) # run lf
By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
|
||
Marek Lindner
|
4871fd2616 |
ipq40xx: add support for Plasma Cloud PA2200
Device specifications:
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200
* GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE
* GPIO-LEDs for power (orange) and status (blue)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3at POE+
+ used as WAN interface
* 12V 2A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
||
|
Marek Lindner
|
ea5bb6bbfe |
ipq40xx: add support for Plasma Cloud PA1200
Device specifications:
* QCA IPQ4018
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200
* 3x GPIO-LEDs for status (cyan, purple, yellow)
* 1x GPIO-button (reset)
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio4:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio3:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3af/at POE(+)
+ used as WAN interface
* 12V/24V 1A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
|
||
Sven Eckelmann
|
8a891bfaa0 |
ipq40xx: Change name for openmesh.sh to vendor-free name
Other vendors are using functionality similar to the ones OpenMesh used to implement two areas on the flash to store the default image and a fallback image. So just change the name to dualboot_datachk.sh to avoid duplicated code just to have the same script for different vendors. Signed-off-by: Sven Eckelmann <sven@narfation.org> |
||
Hans Geiblinger
|
a9071d02b5 |
ipq40xx: Add support for Linksys MR8300 (Dallas)
The Linksys MR8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Hardware Highlights: SoC: IPQ4019 at 717 MHz (4 CPUs) RAM: 512MB RAM SoC: Qualcomm IPQ4019 at 717 MHz (4 CPUs) RAM: 512M DDR3 FLASH: 256 MB NAND (Winbond W29N02GV, 8-bit parallel) ETH: Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks) BTN: Reset and WPS USB: USB3.0, single port on rear with LED SERIAL: Serial pads internal (unpopulated) LED: Four status lights on top + USB LED WIFI1: 2x2:2 QCA4019 2.4 GHz radio on ch. 1-14 WIFI2: 2x2:2 QCA4019 5 GHz radio on ch. 36-64 WIFI3: 2x2:2 QCA9888 5 GHz radio on ch. 100-165 Support is based on the already supported EA8300. Key differences: EA8300 has 256MB RAM where MR8300 has 512MB RAM. MR8300 has a revised top panel LED setup. Installation: "Factory" images may be installed directly through the OEM GUI using URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1) Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com> [copied Hardware-highlights from EA8300. Fixed alphabetical order. fixed commit subject, removed bogus unit-address of keys, fixed author (used Signed-off-By to From:) ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com> |
||
Tomasz Maciej Nowak
|
e24635710c |
ipq40xx: add support for Luma Home WRTQ-329ACN
Luma Home WRTQ-329ACN, also known as Luma WiFi System, is a dual-band
wireless access point.
Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 2 MB SPI NOR
128 MB SPI NAND
WIFI: 2.4 GHz 2T2R integrated
5 GHz 2T2R integrated
Ethernet: 2x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
Bluetooth: 1x 4.0 CSR8510 A10, connected to USB bus
LEDS: 16x multicolor LEDs ring, controlled by MSP430G2403 MCU
Buttons: 1x GPIO controlled
EEPROM: 16 Kbit, compatible with AT24C16
UART: row of 4 holes marked on PCB as J19, starting count from the side
of J19 marking on PCB
1. GND, 2. RX, 3. TX, 4. 3.3V
baud: 115200, parity: none, flow control: none
The device supports OTA or USB flash drive updates, unfotunately they
are signed. Until the signing key is known, the UART access is mandatory
for installation. The difficult part is disassembling the casing, there
are a lot of latches holding it together.
Teardown
Prepare three thin, but sturdy, prying tools. Place the device with back
of it facing upwards. Start with the wall having a small notch. Insert
first tool, until You'll feel resistance and keep it there. Repeat the
procedure for neighbouring walls. With applying a pressure, one edge of
the back cover should pop up. Now carefully slide one of the tools to
free the rest of the latches.
There's no need to solder pins to the UART holes, You can use hook clips,
but wiring them outside the casing, will ease debuging and recovery if
problems occur.
Installation
1. Prepare TFTP server with OpenWrt initramfs image.
2. Connect to UART port (don't connect the voltage pin).
3. Connect to LAN port.
4. Power on the device, carefully observe the console output and when
asked quickly enter the failsafe mode.
5. Invoke 'mount_root'.
6. After the overlayfs is mounted run:
fw_setenv bootdelay 3
This will allow to access U-Boot shell.
7. Reboot the device and when prompted to stop autoboot, hit any key.
8. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
'setenv' to do that, then run following commands:
tftpboot 0x84000000 <openwrt_initramfs_image_name>
bootm 0x84000000
and wait till OpenWrt boots.
9. In OpenWrt command line run following commands:
fw_setenv openwrt "setenv mtdids nand1=spi_nand; setenv mtdparts mtdparts=spi_nand:-(ubi); ubi part ubi; ubi read 0x84000000 kernel; bootm 0x84000000"
fw_setenv bootcmd "run openwrt"
10. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
with:
ubirmvol /dev/ubi0 -N ubi_rootfs
sysupgrade -v -n /tmp/<openwrt_sysupgrade_image_name>
11. After flashing, the access point will reboot to OpenWrt, then it's
ready for configuration.
Reverting to OEM firmware
1. Execute installation guide steps: 1, 2, 3, 7, 8.
2. In OpenWrt command line run following commands:
ubirmvol /dev/ubi0 -N rootfs_data
ubirmvol /dev/ubi0 -N rootfs
ubirmvol /dev/ubi0 -N kernel
ubirename /dev/ubi0 kernel1 kernel ubi_rootfs1 ubi_rootfs
ubimkvol /dev/ubi0 -S 34 -N kernel1
ubimkvol /dev/ubi0 -S 320 -N ubi_rootfs1
ubimkvol /dev/ubi0 -S 264 -N rootfs_data
fw_setenv bootcmd bootipq
3. Reboot.
Known issues
The LEDs ring doesn't have any dedicated driver or application to control
it, the only available option atm is to manipulate it with 'i2cset'
command. The default action after applying power to device is spinning
blue light. This light will stay active at all time. To disable it
install 'i2c-tools' with opkg and run:
i2cset -y 2 0x48 3 1 0 0 i
The light will stay off until next cold boot.
Additional information
After completing 5. step from installation guide, one can disable asking
for root password on OEM firmware by running:
sed -e 's/root❌/root::/' -i /etc/passwd
This is useful for investigating the OEM firmware. One can look
at the communication between the stock firmware and the vendor's
cloud servers or as a way of making a backup of both flash chips.
The root password seems to be constant across all sold devices.
This is output of 'led_ctl' from OEM firmware to illustrate
possibilities of LEDs ring:
Usage: led_ctl [status | upgrade | force_upgrade | version]
led_ctl solid COLOR <brightness>
led_ctl single COLOR INDEX <brightness 0 - 15>
led_ctl spinning COLOR <period 1 - 16 (lower = faster)>
led_ctl fill COLOR <period 1 - 16 (lower = faster)>
( default is 5 )
led_ctl flashing COLOR <on dur 1 - 128> <off dur 1 - 128>
(default is 34) ( default is 34 )
led_ctl pulsing COLOR
COLOR: red, green, blue, yellow, purple, cyan, white
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[squash "ipq-wifi: add BDFs for Luma Home WRTQ-329ACN" into commit,
changed ubi volumes for easier integration, slightly reworded
commit message, changed ubi volume layout to use standard names all
around]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
||
John Crispin
|
0fbdb51f76 |
ipq40xx: add Edgecore OAP-100 support
flashing the unit * first update to latest edcore FW as per the PDF instructions * boot the initramfs - tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm * inside the initramfs call the following commiands - ubiattach -p /dev/mtd0 - ubirmvol /dev/ubi0 -n0 - ubirmvol /dev/ubi0 -n1 - ubirmvol /dev/ubi0 -n2 * scp the sysupgrade image to the board and call - sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin Signed-off-by: John Crispin <john@phrozen.org> |
||
Robert Marko
|
4488b260a0 |
ipq40xx: add Edgecore ECW5211 support
This patch adds support for the Edgecore ECW5211 indoor AP. Specification: - SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7 - RAM: 256MB DDR3 - NOR Flash: 16MB SPI NOR - NAND Flash: 128MB MX35LFxGE4AB SPI-NAND - Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0) - USB: 1 x USB 3.0 SuperSpeed - WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn) - CC2540 BLE connected to USB 2.0 port - Atmel AT97SC3205T I2C TPM Signed-off-by: Robert Marko <robert.marko@sartura.hr> |
||
Yanase Yuki
|
4a77a060ab |
ipq40xx: add support for Buffalo WTR-M2133HP
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.
Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A
Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
# ubidetach -p /dev/mtd15
# ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
# fw_setenv bootcmd bootipq
8. Perform reboot.
Recover to stock firmware
-------------------------
1. Execute the following command.
# fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
|
||
David Bauer
|
300b7fe85a |
ipq40xx: add support for Aruba AP-365
Hardware
--------
SoC: Qualcomm IPQ4029
RAM: 512M DDR3
FLASH: - 128MB NAND (Macronix MX30LF1G18AC)
- 4MB SPI-NOR (Macronix MX25R3235F)
TPM: Atmel AT97SC3203
BLE: Texas Instruments CC2540T
attached to ttyMSM0
ETH: Atheros AR8035
LED: System (red / green / amber)
BTN: Reset
The USB port on the device is (in contrast to other Aruba boards) real
USB. The AP uses a CP2101 USB TTY converter on the board.
Console baudrate is 9600 8n1.
To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.
Installation
------------
1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
into the TFTP server root directory. Configure the TFTP server to
be reachable at 192.168.1.75/24. Connect the machine running the TFTP
server to the ethernet port of the access point.
2. Connect to the serial console. Interrupt autobooting by pressing
Enter when prompted.
3. Configure the bootargs and bootcmd for OpenWrt.
$ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8"
$ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
ubi read 0x85000000 kernel; bootm 0x85000000"
$ setenv ramboot_openwrt "run bootargs_openwrt;
setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
netget; set fdt_high 0x87000000; bootm"
$ setenv bootcmd "run nandboot_openwrt"
$ saveenv
4. Load OpenWrt into RAM:
$ run ramboot_openwrt
5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
/tmp folder on the device.
6. Flash OpenWrt:
Make sure you use the mtd partition with the label "ubi" here!
$ ubidetach -p /dev/mtd1
$ ubiformat /dev/mtd1
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:
$ setenv bootcmd "boot"
$ saveenv
Signed-off-by: David Bauer <mail@david-bauer.net>
|
||
Pawel Dembicki
|
c30220d458 |
ipq40xx: add support for Cell C RTL30VW
Cell C RTL30VW is a LTE router with tho gigabit ethernets and integrated QMI mPCIE modem. This is stripped version of ASKEY RTL0030VW. Hardware: Specification: -CPU: IPQ4019 -RAM: 256MB -Flash: NAND 128MB + NOR 16MB -WiFi: Integrated bgn/ac -LTE: mPCIe card (Modem chipset MDM9230) -LAN: 2 Gigabit Ports -USB: 2x USB2.0 -Serial console: RJ-45 115200 8n1 -Unsupported VoIP Known issues: None so far. Instruction install: There are two methods: Factory web-gui and serial + tftp. Web-gui: 1. Apply factory image via stock web-gui. Serial + initramfs: 1. Rename OpenWrt initramfs image to "image" 2. Connect serial console (115200,8n1) 3. Set IP to different than 192.168.1.11, but 24 bit mask, eg. 192.168.1.4. 4. U-Boot commands: sf probe && sf read 0x80000000 0x180000 0x10000 setenv serverip 192.168.1.4 set fdt_high 0x85000000 tftpboot 0x84000000 image bootm 0x84000000 5. Install sysupgrade image via "sysupgrade -n" Back to stock: All is needed is swap 0x4c byte in mtd8 from 0 to 1 or 1 to 0, do firstboot and factory reset with OFW: 1. read mtd8: dd if=/dev/mtd8 of=/tmp/mtd8 2. go to tmp: cd /tmp/ 3. write first part of partition: dd if=mtd8 of=mtd8.new bs=1 count=76 4. check which layout uses bootloader: cat /proc/mtd 5a. If first are kernel_1 and rootfs_1 write 0: echo -n -e '\x00' >> mtd8.new 5b. If first are kernel and rootfs write 1: echo -n -e '\x01' >> mtd8.new 6. fill with rest of data: dd if=mtd8 bs=1 skip=77 >> mtd8.new 7. CHECK IF mtd8.new HAVE CHANGED ONLY ONE BYTE! e.g with: hexdump mtd8.new 8. write new mtd8 to flash: mtd write mtd8.new /dev/mtd8 9. do firstboot 10.reboot 11. Do back to factory defaults in OFW GUI. Based on work: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> |
||
DENG Qingfang
|
a30abb1b6b |
ipq40xx: add support for MobiPromo CM520-79F
MobiPromo CM520-79F is an AC1300 dual band router based on IPQ4019
Specification:
SoC/Wireless: QCA IPQ4019
RAM: 512MiB
Flash: 128MiB SLC NAND
Ethernet PHY: QCA8075
Ethernet ports: 1x WAN, 2x LAN
LEDs: 7 LEDs
2 (USB, CAN) are GPIO
other 5 (2.4G, 5G, LAN1, LAN2, WAN) are connected to a shift register
Button: Reset
Flash instruction:
Disassemble the router, connect UART pins like this:
GND TX RX
[x x . . x .]
[. . . . . .]
(QCA8075 and IPQ4019 below)
Baud-rate: 115200
Set up TFTP server: IP 192.168.1.188/24
Power on the router and interrupt the booting with UART console
env backup (in case you want to go back to stock and need it there):
printenv
(Copy the output to somewhere save)
Set bootenv:
setenv set_ubi 'set mtdids nand0=nand0; set mtdparts mtdparts=nand0:0x7480000@0xb80000(fs); ubi part fs'
setenv bootkernel 'ubi read 0x84000000 kernel; bootm 0x84000000#config@1'
setenv cm520_boot 'run set_ubi; run bootkernel'
setenv bootcmd 'run cm520_boot'
setenv bootargs
saveenv
Boot initramfs from TFTP:
tftpboot openwrt-ipq40xx-generic-mobipromo_cm520-79f-initramfs-fit-zImage.itb
bootm
After initramfs image is booted, backup rootfs partition in case of reverting to stock image
cat /dev/mtd12 > /tmp/mtd12.bin
Then fetch it via SCP
Upload nand-factory.ubi to /tmp via SCP, then run
mtd erase rootfs
mtd write /tmp/*nand-factory.ubi rootfs
reboot
To revert to stock image, restore default bootenv in uboot UART console
setenv bootcmd 'bootipq'
printenv
use the saved dump you did back when you installed OpenWrt to verify that
there are no other differences from back in the day.
saveenv
upload the backed up mtd12.bin and run
tftpboot mtd12.bin
nand erase 0xb80000 0x7480000
nand write 0x84000000 0xb80000 0x7480000
The BOOTCONFIG may have been configured to boot from alternate partition (rootfs_1) instead
In case of this, set it back to rootfs:
cd /tmp
cat /dev/mtd7 > mtd7.bin
echo -ne '\x0b' | dd of=mtd7.bin conv=notrunc bs=1 count=1 seek=4
for i in 28 48 68 108; do
dd if=/dev/zero of=mtd7.bin conv=notrunc bs=1 count=1 seek=$i
done
mtd write mtd7.bin BOOTCONFIG
mtd write mtd7.bin BOOTCONFIG1
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[renamed volume to ubi to support autoboot,
as per David Lam's test in PR#2432]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
||
Steven Lin
|
a736d912e2 |
ipq40xx: add support for EnGenius EAP2200
SOC: IPQ4019 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB FLASH: NOR 4 MiB + NAND 128 MiB ETH: Qualcomm Atheros QCA8072 WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11a/n/ac 2:2x2 WLAN2: Qualcomm Atheros QCA9888 5GHz 802.11a/n/ac 2:2x2 INPUT: WPS Button LEDS: Power, LAN1, LAN2, WLAN 2.4GHz, WLAN 5GHz-1, WLAN 5GHz-2, OPMODE 1. Load Ramdisk via U-Boot To set up the flash memory environment, do the following: a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters: * 115200bps * 8N1 b. Confirm that the PC is connected to the board using one of the Ethernet ports. c. Set a static ip 192.168.99.8 for Ethernet that connects to board. d. The PC must have a TFTP server launched and listening on the interface to which the board is connected. e. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown. U-BOOT> set serverip 192.168.99.9 && tftpboot 0x84000000 192.168.99.8:openwrt.itb && bootm Signed-off-by: Steven Lin <steven.lin@senao.com> [copied 4.19 dts to 5.4] Signed-off-by: Christian Lamparter <chunkeey@gmail.com> |
||
|
David Bauer
|
c6e972c877 |
ipq40xx: add support for Aruba AP-303H
The Aruba AP-303H is the hospitality version of the Aruba AP-303 with a
POE-passthrough enabled ethernet switch instead of a sigle PHY.
Hardware
--------
SoC: Qualcomm IPQ4029
RAM: 512M DDR3
FLASH: - 128MB SPI-NAND (Macronix)
- 4MB SPI-NOR (Macronix MX25R3235F)
TPM: Atmel AT97SC3203
BLE: Texas Instruments CC2540T
attached to ttyMSM1
ETH: Qualcomm QCA8075
LED: WiFi (amber / green)
System (red / green /amber)
PSE (green)
BTN: Reset
USB: USB 2.0
To connect to the serial console, you can solder to the labled pads next
to the USB port or use your Aruba supplied UARt adapter.
Do NOT plug a standard USB cable into the Console labled USB-port!
Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself
an adapter cable:
VCC - NC
D+ - TX
D- - RX
GND - GND
The console setting in bootloader and OS is 9600 8N1. Voltage level is
3.3V.
To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.
Installation
------------
1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
into the TFTP server root directory. Configure the TFTP server to
be reachable at 192.168.1.75/24. Connect the machine running the TFTP
server to the E0 (!) ethernet port of the access point, as it only
tries to pull from the WAN port.
2. Connect to the serial console. Interrupt autobooting by pressing
Enter when prompted.
3. Configure the bootargs and bootcmd for OpenWrt.
$ setenv bootargs_openwrt "setenv bootargs console=ttyMSM0,9600n8"
$ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
ubi read 0x85000000 kernel; set fdt_high 0x87000000;
bootm 0x85000000"
$ setenv ramboot_openwrt "run bootargs_openwrt;
setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
netget; set fdt_high 0x87000000; bootm"
$ setenv bootcmd "run nandboot_openwrt"
$ saveenv
4. Load OpenWrt into RAM:
$ run ramboot_openwrt
5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
/tmp folder on the device. You will need to plug into E1-E3 ports of
the access point to reach OpenWrt, as E0 is the WAN port of the
device.
6. Flash OpenWrt:
$ ubidetach -p /dev/mtd16
$ ubiformat /dev/mtd16
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:
$ setenv bootcmd "boot"
$ saveenv
Signed-off-by: David Bauer <mail@david-bauer.net>
|
||
|
David Bauer
|
102c8c55f2 |
ipq40xx: add support for Aruba AP-303
Hardware
--------
SoC: Qualcomm IPQ4029
RAM: 512M DDR3
FLASH: - 128MB NAND (Macronix MX30LF1G18AC)
- 4MB SPI-NOR (Macronix MX25R3235F)
TPM: Atmel AT97SC3203
BLE: Texas Instruments CC2540T
attached to ttyMSM0
ETH: Atheros AR8035
LED: WiFi (amber / green)
System (red / green)
BTN: Reset
To connect to the serial console, you can solder to the labled pads next
to the USB port or use your Aruba supplied UARt adapter.
Do NOT plug a standard USB cable into the Console labled USB-port!
Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself
an adapter cable:
VCC - NC
D+ - TX
D- - RX
GND - GND
The console setting in bootloader and OS is 9600 8N1. Voltage level is
3.3V.
To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.
Installation
------------
1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
into the TFTP server root directory. Configure the TFTP server to
be reachable at 192.168.1.75/24. Connect the machine running the TFTP
server to the ethernet port of the access point.
2. Connect to the serial console. Interrupt autobooting by pressing
Enter when prompted.
3. Configure the bootargs and bootcmd for OpenWrt.
$ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8"
$ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
ubi read 0x85000000 kernel; bootm 0x85000000"
$ setenv ramboot_openwrt "run bootargs_openwrt;
setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
netget; set fdt_high 0x87000000; bootm"
$ setenv bootcmd "run nandboot_openwrt"
$ saveenv
4. Load OpenWrt into RAM:
$ run ramboot_openwrt
5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
/tmp folder on the device.
6. Flash OpenWrt:
$ ubidetach -p /dev/mtd1
$ ubiformat /dev/mtd1
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:
$ setenv bootcmd "boot"
$ saveenv
Signed-off-by: David Bauer <mail@david-bauer.net>
|
||
Robert Marko
|
146eb4925c |
ipq40xx: add support for Crisis Innovation Lab MeshPoint.One
MeshPoint.One is Wi-Fi hotspot and smart IoT gateway (based upon Jalapeno module from 8Devices). MeshPoint.One (https://meshpointone.com) is a unique Wi-Fi hotspot and smart city gateway that can be installed and powered from street lighting (even solar power in the future). MeshPoint provides up to 27 hours of interrupted Wi-Fi and IoT services from internal battery even when external power is not available. MeshPoint.One can be used for disaster relief efforts in order to provide instant Wi-Fi coverage that can be easily expanded by just adding more devices that create wide area mesh network. MeshPoint.One devices have standard Luci UI for management. Features: - 1x 1Gpbs WAN - 1x 1Gbps LAN - POE input (eth0) - POE output (eth1) - Sensor for temperature, humidity and pressure (Bosch BME280) - current, voltage and power measurement via TI INA230 - Hardware real time clock - optional power via Li-Ion battery - micro USB port with USB to serial chip for easy OpenWrt terminal access - I2C header for connecting additional sensors Installation: ------------- Simply flash the sysupgrade image from stock firmware. Or use the built in Web recovery into bootloader: Hold Reset button for 5 to 20 seconds or use UART and httpd command. Web UI will appear on 192.168.2.100 by default. For web recovery use the factory.ubi image. Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr> Signed-off-by: Damir Franusic <damir.franusic@sartura.hr> Signed-off-by: Valent Turkovic <valent@meshpoint.me> Signed-off-by: Robert Marko <robert@meshpoint.me> [commit description long line wrap, usb->USB] Signed-off-by: Petr Štetiar <ynezz@true.cz> |
||
Daniel Danzberger
|
affe633be4 |
ipq40xx: ipq4019: Add new device Compex WPJ419
This device contains 2 flash devices. One NOR (32M) and one NAND (128M).
U-boot and caldata are on the NOR, the firmware on the NAND.
SoC: IPQ4019
CPU: 4x 710MHz ARMv7
RAM: 256MB
FLASH: NOR:32MB NAND:128MB
ETH: 2x GMAC Gigabit
POE: 802.3 af/at POE, IEEE802.3af/IEEE802.3at(48-56V)
WIFI: 1x 2.4Ghz Atheros qca4019 2x2 MU-MIMO
1x 5.0Ghz Atheros qca4019 2x2 MU-MIMO
USB: 1x 3.0
PCI: 1x Mini PCIe
SIM: 1x Slot
SD: 1x MicroSD slot
BTN: Reset
LED: - Power
- Ethernet
UART: 1x Serial Port 4 Pin Connector (UART)
1x Serial Port 6 Pin Connector (High Speed UART)
POWER: 12V 2A
Installation
------------
Initial flashing can only be done via u-boot using the following commands:
tftpboot openwrt-ipq40xx-generic-compex_wpj419-squashfs-nand-factory.ubi
nand erase.chip; nand write ${fileaddr} 0x0 ${filesize}
res
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
|
||
|
David Bauer
|
7f187229a8 |
ipq40xx: add support for AVM FRITZ!Repeater 1200
Hardware
--------
SoC: Qualcomm IPQ4019
RAM: 256M DDR3
FLASH: 128M NAND
WiFi: 2T2R IPQ4019 bgn
2T2R IPQ4019 a/n/ac
ETH: Atheros AR8033 RGMII PHY
BTN: 1x Connect (WPS)
LED: Power (green/red/yellow)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz1200'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz1200.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ1200.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz1200.bin uboot0
> mtd write /path/to/uboot-fritz1200.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
|
||
Rafał Miłecki
|
a858db3136 |
treewide: sysupgrade: use $UPGRADE_BACKUP to check for backup
Now that $UPGRADE_BACKUP is set conditionally there is no need to check the $UPGRADE_OPT_SAVE_CONFIG anymore. All conditions can be simplified. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> |
||
|
Rafał Miłecki
|
641f6b6c26 |
treewide: use new procd sysupgrade $UPGRADE_BACKUP variable
It's a variable set by procd that should replace hardcoded
/tmp/sysupgrade.tgz.
This change requires the most recent procd with the commit 0f3c136
("sysupgrade: set UPGRADE_BACKUP env variable").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
||
|
Rafał Miłecki
|
5797fe84a3 |
treewide: replace remaining (not working now) $SAVE_CONFIG uses
This var has been replaced by the $UPGRADE_OPT_UPGRADE_OPT_SAVE_CONFIG
Fixes:
|
||
|
Rafał Miłecki
|
1cbe0d659c |
treewide: sysupgrade: get rid of platform_nand_pre_upgrade()
1) nand_do_upgrade() is always called by a target code 2) nand_do_upgrade() starts with calling platform_nand_pre_upgrade() It means there is no need for the platform_nand_pre_upgrade() callback at all. All code that was present there could bo moved & simplly called by a target right before the nand_do_upgrade(). Signed-off-by: Rafał Miłecki <rafal@milecki.pl> |
||
|
Rafał Miłecki
|
8b4bc7abe0 |
treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()
stage2 passes image path to platform_do_upgrade() as an argument so it can be simply accessed using $1 Signed-off-by: Rafał Miłecki <rafal@milecki.pl> |
||
Jeff Kletsky
|
1440175f82 |
ipq40xx: Linksys: sysupgrade: Ensure OEM volumes are removed
When OEM volumes are present in the [alt_]firmware partition,
sysupgrade will write a new kernel, but will fail to write
the root file system. The next boot will hang indefinitely
Waiting for root device /dev/ubiblock0_0...
Modified ipq40xx/base-files/lib/upgrade/linksys.sh
to remove both `squashfs` and `ubifs` if found
on the target firmware partition's UBI device.
Run-tested-on: Linksys EA8300
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[applied some shellcheck suggestions as well]
|
||
|
Jeff Kletsky
|
819e7946b0 |
ipq40xx: Add support for Linksys EA8300 (Dallas)
The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three,
independent radios. NAND provides two, alternate kernel/firmware
images with fail-over provided by the OEM U-Boot.
Installation:
"Factory" images may be installed directly through the OEM GUI.
Hardware Highlights:
* IPQ4019 at 717 MHz (4 CPUs)
* 256 MB NAND (Winbond W29N02GV, 8-bit parallel)
* 256 MB RAM
* Three, fully-functional radios; `iw phy` reports (FCC/US, -CT):
* 2.4 GHz radio at 30 dBm
* 5 GHz radio on ch. 36-64 at 23 dBm
* 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm
#{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1
* All two-stream, MCS 0-9
* 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights
* USB3, single port on rear with LED
* WPS and reset buttons
* Four status lights on top
* Serial pads internal (unpopulated)
"Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1"
Implementation Notes:
The OEM flash layout is preserved at this time with 3 MB kernel and
~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and
syscfg (56 MB) partitions are untouched, available as read-only.
Serial Connectivity:
Serial connectivity is *not* required to flash.
Serial may be accessed by opening the device and connecting
a 3.3-V adapter using 115200, 8n1. U-Boot access is good,
including the ability to load images over TFTP and
either run or flash them.
Looking at the top of the board, from the front of the unit,
J3 can be found on the right edge of the board, near the rear
|
J3 |
|-| |
|O| | (3.3V seen, open-circuit)
|O| | TXD
|O| | RXD
|O| |
|O| | GND
|-| |
|
Unimplemented:
* serial1 "ttyQHS0" (serial0 works as console)
* Bluetooth; Qualcomm CSR8811 (potentially conected to serial1)
Other Notes:
https://wikidevi.com/wiki/Linksys_EA8300 states
FCC docs also cover the Linksys EA8250. According to the
RF Test Report BT BR+EDR, "All models are identical except
for the EA8300 supports 256QAM and the EA8250 disable 256QAM."
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
|
||
|
Jeff Kletsky
|
b3770eaca3 |
mtd: base-files: Unify dual-firmware devices (Linksys)
Consistently handle boot-count reset and upgrade across ipq40xx, ipq806x, kirkwood, mvebu Dual-firmware devices often utilize a specific MTD partition to record the number of times the boot loader has initiated boot. Most of these devices are NAND, typically with a 2k erase size. When this code was ported to the ipq40xx platform, the device in hand used NOR for this partition, with a 16-byte "record" size. As the implementation of `mtd resetbc` is by-platform, the hard-coded nature of this change prevented proper operation of a NAND-based device. * Unified the "NOR" variant with the rest of the Linksys variants * Added logging to indicate success and failure * Provided a meaningful return value for scripting * "Protected" the use of `mtd resetbc` in start-up scripts so that failure does not end the boot sequence * Moved Linksys-specific actions into common `/etc/init.d/bootcount` For upgrade, these devices need to determine which partition to flash, as well as set certain U-Boot envirnment variables to change the next boot to the newly flashed version. * Moved upgrade-related environment changes out of bootcount * Combined multiple flashes of environment into single one * Current-partition detection now handles absence of `boot_part` Runtime-tested: Linksys EA8300 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [checkpatch.pl fixes, traded split strings for 80+ chars per line] |
||
|
David Bauer
|
148d29d47b |
ipq40xx: add support for AVM FRITZ!Repeater 3000
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M (NANYA NT5CC128M16JR-EK)
FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI)
ETH: Qualcomm QCA8072
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
WiFi5: QCA9984 4T4R 4SS n/ac
LED: - Connect green/blue/red
- Power green
BTN: WPS/Connect
UART: 115200n8 3.3V
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz3000'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ3000.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz3000.bin uboot0
> mtd write /path/to/uboot-fritz3000.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
|
||
|
David Bauer
|
95b0c07a61 |
ipq40xx: add support for FritzBox 7530
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M
FLASH: 128M NAND
ETH: QCA8075
VDSL: Intel/Lantiq VRX518 PCIe attached
currently not supported
DECT: Dialog SC14448
currently not supported
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
LED: - Power/DSL green
- WLAN green
- FON/DECT green
- Connect/WPS green
- Info green
- Info red
BTN: - WLAN
- FON
- WPS/Connect
UART: 115200n8 3.3V (located under the Dialog chip)
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz7530'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ7530.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz7530.bin uboot0
> mtd write /path/to/uboot-fritz7530.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
[removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
||
张鹏
|
bbab33724d |
ipq40xx: add support for Qxwlan E2600AC C1 and C2
Qxwlan E2600AC C1 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB FLASH: 32 MiB Winbond W25Q256 ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power ,6 driven by gpio SERIAL: UART (J5) UUSB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Qxwlan E2600AC C2 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB NOR: 16 MiB Winbond W25Q128 NAND: 128MiB Micron MT29F1G08ABAEAWP ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power, 6 driven by gpio SERIAL: UART (J5) USB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "ubi" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com> [ added rng node. whitespace fixes, ported 02_network, ipq-wifi Makefile, misc dts fixes, trivial message changes ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com> |
||
Piotr Dymacz
|
c568c6dc09 |
ipq40xx: add support for ALFA Network AP120C-AC
ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm IPQ4018 + QCA8075 platform. Specification: - Qualcomm IPQ4018 (717 MHz) - 256 MB of RAM (DDR3) - 16 MB (SPI NOR) + 128 MB (SPI NAND) of flash - 2x Gbps Ethernet, with 802.3af PoE support in one port - 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922) - 3x U.FL connectors - 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas - Atmel/Microchip AT97SC3205T TPM module (I2C bus) - TI CC2540 Bluetooth LE module (USB 2.0 bus) - 4x LED (all driven by GPIO) - 1x button (reset) - 1x USB 2.0 (optional, not installed in indoor version) - DC jack for main power input (12 V) - UART header available on PCB (2.0 mm pitch) Flash instruction: 1. This board uses dual-image feature (128 MB NAND is divided into two 64 MB partitions: 'rootfs1' and 'rootfs2'). 2. Before update, make sure your device is running firmware no older than v1.1 (previous versions have incompatible U-Boot). 3. Use 'factory' image in vendor GUI or for sysupgrade tool, without preserving settings. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> |
||
Marius Genheimer
|
9ad3967f14 |
ipq40xx: add support for ASUS Lyra
SoC: Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores
RAM: 256 MiB (Nanya NT5CC128M16IP-DI)
FLASH: 128 MiB (Macronix NAND)
WiFi0: Qualcomm IPQ4019 b/g/n 2x2
WiFi1: Qualcomm IPQ4019 a/n/ac 2x2
WiFi2: Qualcomm Atheros QCA9886 a/n/ac
BT: Atheros AR3012
IN: WPS Button, Reset Button
OUT: RGB-LED via TI LP5523 9-channel Controller
UART: Front of Device - 115200 N-8
Pinout 3.3v - RX - TX - GND (Square is VCC)
Installation:
1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp.
Login credentials are identical to the Web UI.
2. Login to the device via SSH.
3. Flash the initramfs image using
> mtd-write -d linux -i openwrt-image-file
4. Power-cycle the device and wait for OpenWRT to boot.
5. From there flash the OpenWRT-sysupgrade image.
Ethernet-Ports: Although labeled identically, the port next to
the power socket is the LAN port and the other one is WAN. This
is the same behavior as in the stock firmware.
Signed-off-by: Marius Genheimer <mail@f0wl.cc>
[Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh,
reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79,
minor dts touchup, added rng to 4.19 dts]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
||
Oever González
|
a873b29284 |
ipq40xx: add support for Linksys EA6350v3
Specifications:
SOC: Qualcomm IPQ4018
RAM: 256 MiB Samsung K4B2G1646F-BYK0
FLASH1: MX25L1605D 2 MB
FLASH2: Winbond W25N01GV 128Mb
ETH: Qualcomm QCA8075
WLAN0: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN1: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: WPS, Reset
LED: Status - Green
SERIAL: Header at J19, Beneath DC Power Jack
1-VCC ; 2-TX ; 3-RX; 4-GND;
Serial 115200-8-N-1.
Tested and working:
- USB (requires extra packages)
- LAN Ethernet (Correct MAC-address)
- WAN Ethernet (Correct MAC-address)
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from Web UI
- OpenWRT sysupgrade
- LED
- Reset Button
Need Testing:
- WPS button
Install via Web UI:
- Attach to a LAN port on the router.
- Connect to the Linksys Smart WiFi Page (default 192.168.1.1) and login
- Select the connectivity tab on the left
- In the manual update box on the right
- Select browse, and browse to
openwrt-ipq40xx-linksys_ea6350v3-squashfs-factory.bin
- Click update.
- Read and accept the warning
- The router LED will start blinking. When the router LED goes solid, you
can now navigate to 192.168.1.1 to your new OpenWrt installation.
Sysupgrade:
- Flash the sysupgrade image as usual. Please: try to do a reset everytime
you can (doing it with LuCI is easy and can be done in the same step).
Recovery (Automatic):
- If the device fails to boot after install or upgrade, whilst the unit is
turned on:
1 - Wait 15 seconds
2 - Switch Off and Wait 10 seconds
3 - Switch on
4 - Repeat steps 1 to 3, 3 times then go to 5.
5 - U-boot will have now erased the failed update and switched back to the
last working firmware - you should be able to access your router on
LAN.
Recovery (Manual):
- The steps for manual recovery are the same as the generic u-boot tftp
client method.
Back To Stock:
- Use the generic recovery using the tftp client method to flash the
"civic.img". Also you can strip-and-pad the original image and use
the generic "mtd" method by flashing over the "kernel" partition.
* Just be careful to flash in the partition that the device is currently
booted.
Signed-off-by: Ryan Pannell <ryan@osukl.com>
Signed-off-by: Oever González <notengobattery@gmail.com>
[minor edits, removed second compatible of nand, added dtb entry to 4.19]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
||
Marek Lindner
|
8ad45992ac |
ipq40xx: fix openmesh sysupgrade with tar content out of order
The tar extraction depends on the order in which the files
are added to the tar file. Since the order is not guaranteed
and depends on the host system, the combined mtd write fails
with sysupgrade images built on some systems.
Fix by changing to tar file order independent mtd write.
Fixes:
|
||
Sven Eckelmann
|
ebd57de1f9 |
ipq40xx: Create /var/lock directory in platform_do_upgrade_*
The sysupgrade_pre_upgrade hook was removed with |
||
Mathias Kresin
|
56b8ac1e86 |
treewide: consolidate upgrade state set
Set the (sys)upgrade state when sourcing the stage2 script instead of setting the state for each target individual. This change fixes the, due to a missing state set, not working upgrade led on ath79 and apm821xx. Signed-off-by: Mathias Kresin <dev@kresin.me> |
||
Christian Lamparter
|
82618062cf |
ipq40xx: add support for the ZyXEL NBG6617
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
|
||
|
Sven Eckelmann
|
0b20490207 |
ipq40xx: add support for OpenMesh A62
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
|
||
|
Robert Marko
|
1e341bb5ef |
ipq40xx: add support for 8devices Jalapeno
This patch adds support for 8devices Jalapeno. Specification: QCA IPQ4018, Quad core ARM v7 Cortex A7 717MHz 256 MB of DDR3 RAM 8 MB of SPI NOR flash 128 MB of Winbond SPI NAND flash WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 requires special BDF in QCA4019/hw1.0/board-2.bin with: bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=8devices-Jalapeno WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 requires special BDF in QCA4019/hw1.0/board-2.bin with: bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=8devices-Jalapeno ETH: Qualcomm Atheros QCA8072 Gigabit Switch (1 x LAN, 1 x WAN) phy@mdio3: Label: eth0 gmac0 phy@mdio4: Label: eth1 gmac1 Installation instructions: Since boards ship with old version of LEDE installation is simple. Just use sysupgrade -n -F sysupgrade.bin Syuspgrade needs to be forced since OpenWRT uses DT detection in recent releases. If you get error that FIT configuration is not found during boot it is due to older U-boot used on your board. That is because 8devices used custom FIT configuration partition name as they internally had v1 and v2 boards. Only v2 boards are sold so now they are shipping boards with never U-boot using generic config@1 FIT partition name. Also for old uboot it is possible to force loading config@1 by changing uboot environment: setenv boot5 'bootm 0x84000000#config@1’ saveenv Signed-off-by: Robert Marko <robimarko@gmail.com> |
||
Chris Blake
|
4943afd781 |
ipq40xx: add Cisco Meraki MR33 Support
This patch adds support for Cisco Meraki MR33 hardware highlights: SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable) ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80 WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2 WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80 LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1) 1 x Orange LED Fault Indicator (shared with LP5562) 2 x LAN Activity / Speed LEDs (On the RJ45 Port) BUTTON: one Reset button MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8 AT24C64 8KiB EEPROM Kensington Lock Serial: WARNING: The serial port needs a TTL/RS-232 3V3 level converter! The Serial setting is 115200-8-N-1. The board has a populated 1x4 0.1" header with half-height/low profile pins. The pinout is: VCC (little white arrow), RX, TX, GND. Flashing needs a serial adaptor, as well as patched ubootwrite utility (needs Little-Endian support). And a modified u-boot (enabled Ethernet). Meraki's original u-boot source can be found in: <https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427> Add images to do an installation via bootloader: 0. open up the MR33 and connect the serial console. 1. start the 2nd stage bootloader transfer from client pc: # ubootwrite.py --write=mr33-uboot.bin (The ubootwrite tool will interrupt the boot-process and hence it needs to listen for cues. If the connection is bad (due to the low-profile pins), the tool can fail multiple times and in weird ways. If you are not sure, just use a terminal program and see what the device is doing there. 2. power on the MR33 (with ethernet + serial cables attached) Warning: Make sure you do this in a private LAN that has no connection to the internet. - let it upload the u-boot this can take 250-300 seconds - 3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin (the u-boot is listening on 192.168.1.1) # tftp 192.168.1.1 binary put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin 4. wait for it to reboot 5. connect to your MR33 via ssh on 192.168.1.1 For more detailed instructions, please take a look at the: "Flashing Instructions for the MR33" PDF. This can be found on the wiki: <https://openwrt.org/toh/meraki/mr33> (A link to the mr33-uboot.bin + the modified ubootwrite is also there) Thanks to Jerome C. for sending an MR33 to Chris. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> |
||
Christian Lamparter
|
87c42101cf |
ipq40xx: add support for ASUS RT-AC58U/RT-ACRH13
This patch adds support for ASUS RT-AC58U/RT-ACRH13.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI
NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE)
NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI)
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one Reset and one WPS button
LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each)
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has an unpopulated
1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the
PCB right next to the connector.
U-Boot Note: The ethernet driver isn't always reliable and can sometime
time out... Don't worry, just retry.
Access via the serial console is required. As well as a working
TFTP-server setup and the initramfs image. (If not provided, it
has to be built from the OpenWrt source. Make sure to enable
LZMA as the compression for the INITRAMFS!)
To install the image permanently, you have to do the following
steps in the listed order.
1. Open up the router.
There are four phillips screws hiding behind the four plastic
feets on the underside.
2. Connect the serial cable (See notes above)
3. Connect your router via one of the four LAN-ports (yellow)
to a PC which can set the IP-Address and ssh and scp from.
If possible set your PC's IPv4 Address to 192.168.1.70
(As this is the IP-Address the Router's bootloader expects
for the tftp server)
4. power up the router and enter the u-boot
choose option 1 to upload the initramfs image. And follow
through the ipv4 setup.
Wait for your router's status LED to stop blinking rapidly and
glow just blue. (The LAN LED should also be glowing blue).
3. Connect to the OpenWrt running in RAM
The default IPv4-Address of your router will be 192.168.1.1.
1. Copy over the openwrt-sysupgrade.bin image to your router's
temporary directory
# scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp
2. ssh from your PC into your router as root.
# ssh root@192.168.1.1
The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key.
Once connected...: run the following commands on your temporary installation
3. delete the "jffs2" ubi partition to make room for your new root partition
# ubirmvol /dev/ubi0 --name=jffs2
4. install OpenWrt on the NAND Flash.
# sysupgrade -v /tmp/openwrt-sysupgrade.bin
- This will will automatically reboot the router -
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|