Commit Graph

4 Commits

Author SHA1 Message Date
Hang Zhou
f637cf5ef7 bmips: add support for Sagem F@ST3864OP
Specifications:
* SoC: BCM63168
* RAM: NT5CC64M16GP-DI, DDR3 128MiB
* NAND: W29N01HVSINA, 128MiB
* Ethernet: 4x1000M LAN, 1x 1000M WAN
* Serial interface: on board but not populated, 3.3V, 115200, 8N1

Notes:
* Use DSA for VLAN and switches
* Ethernet ports and USB works
* gpio-leds are not working
* WLAN, xDSL, and FXS are not going to work

Signed-off-by: Hang Zhou <929513338@qq.com>
[refactor, reorder, drop unneeded or not working stuff]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2024-06-26 19:28:13 +02:00
Kyle Hendry
1a69543376 bmips: add support for SmartRG SR505n
Specifications:
- SoC: Broadcom BCM63168 dual 400MHz MIPS
- Flash: 16MB SPI NOR W25Q128WFG
- RAM: 128MB DDR3 W631GG6KB-15
- Ethernet: 1x 1000M, 3x 100M
- Wifi: BCM435F
- 1x USB 2.0 port
- 3x Button
- 12x LED

Flashing via serial
- Connect to the 3.3V TTL UART on the board
  (J6 pinout Vcc Rx Tx Gnd) at 115200-8-N-1
- Press any key in the serial console when powering up the board to enter
  the CFE prompt
- Configure an interface on your workstation to static IP 192.168.1.100
  and connect it to the board
- Start a TFTP server with the firmware image
- On the CFE prompt, enter the command
  "f 192.168.1.100:openwrt-bmips-bcm63268-smartrg_sr505n-squashfs-cfe.bin"

Signed-off-by: Kyle Hendry <kylehendrydev@gmail.com>
[Remove unneeded LED labels]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2024-03-10 20:26:07 +01:00
Álvaro Fernández Rojas
47cc09aa7a bmips: add support for Comtrend VG-8050
The Comtrend VG-8050 is a wifi gigabit ethernet router, 2.4 GHz single band with
two external antennas.

Hardware:
 - SoC: Broadcom BCM63169
 - CPU: dual core BMIPS4350 @ 400Mhz
 - RAM: 128 MB DDR
 - Flash: 128 MB NAND
 - LAN switch: Broadcom BCM53125, 5x 1Gbit
 - Wifi 2.4 GHz: SoC (BCM63268) 802.11bgn
 - USB: 1x 2.0 (optional)
 - Buttons: 2x (reset)
 - LEDs: yes
 - UART: yes

Installation via CFE web UI:
  1. Power off the router.
  2. Press reset button near the power switch.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Browse to http://192.168.1.1 and upload the firmware.
  5. Wait a few minutes for it to finish.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-06-16 09:48:53 +02:00
Álvaro Fernández Rojas
6fd8e0f943 bmips: add subtargets for each SoC
BMIPS is a generic arch that can be used for multiple Broadcom SoCs, each one
with its own specific drivers, so instead of having a huge kernel supporting
all of them, let's switch to a subtarget per SoC like other OpenWrt targets.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-10 10:04:08 +02:00