The BDFs for OpenMesh A42 were upstreamed [1] to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-01-26. The
ipq-wifi-openmesh_a42 package can now be dropped because OpenWrt already
ships the QCA4019 board-2.bin from this version.
[1] https://wireless.wiki.kernel.org/en/users/drivers/ath10k/boardfiles
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
During the integration of the ipq40xx target,
the phy drivers were included into the ipq806x's
target kernel config.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch renames the AVM FRITZ!Box 4040's board-2.bin
file and package to match the 'vendor_product' format.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Ubifs is disabled for all boards except the evaluation boards and the
Fritz!Box 4040 anyway. According the author, the ubifs support for the
Fritz!Box 4040 wasn't enabled on purpose.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Remove leftover code used for legacy images. There are no relevant
binary differences for the images after removing the legacy leftovers.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Initialise the filesystem specific build command. Otherwise it will be
unintended inherit to following images and will cause a wrong image
format.
The issue is around for ages but was only recently triggered due to the
added support for the Openmesh a42.
Fixes: FS#1276
Signed-off-by: Mathias Kresin <dev@kresin.me>
* QCA IPQ401x
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
* powered only via POE
- 802.3af POE on Ethernet 1
- 18-24v passive POE (mode B) on Ethernet 2
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Use the generic board detection method:
- Board name: First compatible string from the device tree
- Board model: Model property from the device tree
Change occurrences of board name in userspace by the compatible
string, and removed target specific board detection script
Replace the definition of SUPPORTED_DEVICES in Device/Default
to extract the dt compatible string from each device definition.
Additionally, for devices supported by lede-17.01, append
the value of BOARD_NAME to SUPPORTED_DEVICES in the device
definition.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Use <manufacturer>_<modelname> as image name for board using the
devicetree compat string as boardname.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
This will avoid some conflicts when doing a git rebase or merge,
specially when adding support to a new device.
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
[drop brcm47xx changes which rename the images]
Signed-off-by: Mathias Kresin <dev@kresin.me>
AP-DK01.1-C1 is QCA dev board with:
- ipq4018 quad core ARM @716.8MHz, 2x2 dual (11n+11ac) radio
- 256MB RAM
- 32MB SPI flash
- QCA8075 multiport ethernet phy (WAN port, 4x LAN ports)
First installation via u-boot:
sf probe
sf erase 0x180000 0x1a00000
tftpboot 0x84000000 lede-ipq806x-AP-DK01.1-C1-squashfs-sysupgrade.bin
sf write 0x84000000 0x180000 $filesize
Further upgrades via sysupgrade.
Changes:
- add partitions
- set memory size to 256MB
- add reserved memory mapping
- add correct compatible string
- add image generation
- extract pre-cal data from ART partition
Compile and run tested.
Wirespeed NAT can be achieved with spreading rx interrupts over different
cores. Wifi speed is ~550Mbps @5GHz in open air.
Note:
AP-DK01.1-C1 is fully compatible with AP-DK01.2-C1, which has
ipq4028 instead of ipq4018 on board.
Changes since v2:
- based on dts(i) rework/cleanup submitted:
http://lists.infradead.org/pipermail/lede-dev/2017-October/009596.html
- precise reserved memory mapping
- more precise description
- compatible string
Signed-off-by: Roman Yeryomin <roman@advem.lv>
The ZyXEL NBG6817 uses an eMMC flash for the rootfs, which is split
into the readonly squashfs and ext4 for the overlay. This adds the
required package to the device packages to allow mounting the overlay
by default.
/dev/root on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,nosuid,nodev,noexec,noatime)
sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
/dev/loop0 on /overlay type ext4 (rw,noatime,data=ordered)
overlayfs:/overlay on / type overlay (rw,noatime,lowerdir=/,upperdir=/overlay/upper,workdir=/overlay/work)
tmpfs on /dev type tmpfs (rw,nosuid,relatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,mode=600,ptmxmode=000)
debugfs on /sys/kernel/debug type debugfs (rw,noatime)
mountd(pid1040) on /tmp/run/blockd type autofs (rw,relatime,fd=7,pgrp=1,timeout=30,minproto=5,maxproto=5,indirect)
Before this commit, the ext4 based overlayfs could not be mounted,
which left only the tmpfs based/ volatile emergency overlay in place.
Fixes: https://forum.lede-project.org/t/zyxel-nbg6817-flashing-from-oem/768
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
IMG_PREFIX can be modified in ImageBuilder by passing EXTRA_IMAGE_NAME
on command line, but Image/Prepare is not run in ImageBuilder. This
causes missing files when IMG_PREFIX is used for target file names in
Image/Prepare, then as source file names in Image/BuildKernel or
Image/Build.
Fix this by using a fixed output file name in Image/Prepare, and copy to
the expected file name in Image/BuildKernel instead, which is run by
ImageBuilder.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
This change enables .itb image generation for AP148,
It will help us to boot and test AP148 with NOR flash.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
This change add IPQ40xx AP-DK04.1-C1 board image support,
enables ubi image for IPQ40xx AP-DK04.1-C1 board and also
add sysupgrage support for AP-DK04.1-C1 and generates a
sysupgrade.tar image.
Testing:
*Tested on IPQ40xx AP-DK04.1-C1:
a. NAND boot
b. ubi sysupgrade
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Split the fritz-tools into subpackages. fritz_tffs_read is usefull for
all Fritz boards where fritz-cal_extract is only required for the
Fritz 4040 at the moment.
Rename the tffs related binary to the more catchy name fritz_tffs and
move the whole package to utilities since the package doesn't really
provide a firmware file.
Make the fritz-tools available for all targets and build them shared.
The tffs is used by avm on lantiq and ar71xx as well.
Tested-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Netgear X4 R7500 comes with a QCA988X. Select a firmware that matches
the ath10k chipset
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
This patch adds support for AVM FRITZ!Box 4040.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB Nanya NT5CC128M16IP
FLASH: 32 MiB MXIC MX25L25635FMI
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one WLAN and one WPS button
LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN.
Serial:
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1. The SoC's serial port is right
next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1"
header for it. Use a multimeter to figure out the pinout!
This board currently needs an additional u-boot image in order to boot
properly. Booting with EVA isn't possible ATM.
Install Procedure:
0. It's highly recommended to connect to the serial port.
The serial settings are listed above.
1. install a u-boot image for AVM Fritz!Box 4040
(see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and
<https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>)
2. upload the initramfs.itb image via tftp (u-boot listens to
192.168.1.1 - use binary transfer mode!)
3. connect to the FB4040 and use sysupgrade sysupgrade.bin
to install the image.
Works:
- Switch and Ethernet (99%)
- Buttons (WLAN, WPS)
- FLASH (1 x 32MiB NOR Chip)
- WLAN2G and WLAN5G
- CPUFREQ scaling
- PRNG
- serial
- Crypto Accelerator
- sysupgrade (Read the flash instructions to avoid bricking)
- full LEDE Install (Read the flash instructions to avoid bricking)
- LEDs (Power, WAN, Info (red and amber), LAN)
The LEDs are connected to the QCA8075 LED ports.
The AR40xx driver contains a gpio-controller to
handle these special "GPIOs".
- USB Both 3.0 and 2.0 ports
- many packages from other ARMv7 boards
(This does include the RaspberryPi Model 2!)
- ...
Not planned:
- WAN<->LAN short-cut
- Qualcomm Secure Execution Environment
- ...
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John Crispin <john@phrozen.org>
The more straight forward approach for generating the pure and unpadded
kernel file which then can be used for initramfs straight.
Build options for factory.img and sysupgrade.tar are handeled
seperately.
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
The fakeroot header is expected by the netgear bootloader in the last
64 bytes of the last block used by the uImage. With the current
linux-4.9 uImage being more than 128k smaller than the linux-4.4 uImage
the bootloader was unable to locate the rootfs ih_magic and was
refusing to load and start the kernel.
Fixes: FS#542
Signed-off-by: Thomas Reifferscheid <thomas@reifferscheid.org>
This patch moves the fakeroot code required by some devices to
`image-commands.mk`.
Create the fakeroot on the fly by using the undocumented -s (skip copy)
parameter of mkimage.
Signed-off-by: Joseph C. Lehner <joseph.c.lehner@gmail.com>
[remove unused NETGEAR_KERNEL_MAGIC, remove workarounds to have a dummy
rootfs for mkimage]
Signed-off-by: Mathias Kresin <dev@kresin.me>
This router is similar to the C2600. Ethernet on WAN + LAN, switch,
sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem
and the POTS/DECT interface are not supported yet.
It is not possible to flash LEDE via the TP-Link webinterface. The
image need to be signed. The first 0x200 bytes of the image is the
TP-Link header including the signature. The signature is not validated
by the bootloader. The LEDE image is zeroed in this area.
To install LEDE it is necessary to solder a four pin header to JP2.
Connect a serial interface to this header and interrupt the autostart
of kernel. Transfer the sysupgrade image via TFTP and write it to the
serial flash at 0x320000.
Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
CPU: 2x1.8GHz ARM, RAM: 512MiB
Storage: 4MiB serial Flash, 3.9GiB MMC
NIC: 2x1GBit/s, Switch with 5 external and 2 internal ports
WiFi: Dualband, ath10k 2.4GHz, 5GHz MU-MIMO
For installation copy xx-mmcblk0p4-kernel.bin and xx-mmcblk0p5-rootfs-full.bin
to device. Then run:
cat xx-mmcblk0p4-kernel.bin > /dev/mmc0blk0p4
cat xx-mmcblk0p5-rootfs-full.bin > /dev/mmc0blk0p5
reboot -f
For debugging serial console is easily visible on board, no soldering needed.
Signed-off-by: André Valentin <avalentin@marcant.net>
The R7800 is an IPQ8065, so rename its dts file to reflect that fact.
Also fold the R7500v2 dts addition into the existing 800-devicetree.patch.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Alexis Green <alexis@cessp.it>
[Jo-Philipp Wich: add missing DEVICE_TITLE, fix model name in commit title]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Now that the "sysupgrade-nand" step is used by non-NAND targets as well,
rename it to "sysupgrade-tar" to make it more generic.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
It is used by a core build template, so the variable should be
initialized and added to DEVICE_VARS in the core.
Same for DEVICE_DTS_DIR
Signed-off-by: Felix Fietkau <nbd@nbd.name>
1)Changes
- Rebased the patches for linux-4.4.7
- Added patch to fix spi nor fifo and dma support
- Added patch to configure watchdog barktime
2)Testing
Tested on IPQ AP148 Board:
a. NOR boot and NAND boot
b. ethernet network and ath10k wifi
c. ubi sysupgrade
UnTested
dwc3 usb has not been validated on IPQ board(AP148)
3)Known Issues:
Once we flash ubi image on AP148, and if we reset the board, uboot on
first boot creates PEB and LEB for dynamic sized partitions, which is incorrect
and not what linux expects which causes errors when trying to mount rootfs.
In order to test this, we can use the below steps:
a. Flash the ubi image on board and don't reset the board
b. load the kernel fit image in RAM and boot from there.
Signed-off-by: Ram Chandra Jangir <rjangi@codeaurora.org>
