For quite some time, the tiny (4M flash) TP-Link sysupgrade and
factory images cannot be built anymore by the buildbots, just
the initramfs-kernel.bin files are still there.
Disable these images for the buildbots and prevent useless builds.
Note that these devices still build fine with default settings,
even for kernel 5.4.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In 02_network, the board name solidrun,clearfog-a1 is used in a
case, but it does not seem to be used/exist anywhere else in OpenWrt.
The valid strings are:
- solidrun,clearfog-pro-a1
- solidrun,clearfog-base-a1
Fixes: 12795ec9f1 ("mvebu: split interface configuration for
clearfog pro and base")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Generate additional images that are compatible to the cpximg loader.
The cpximg loader can be started either by holding the reset button during
power up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept the image
appropriate for the board revision that is etched on the board.
For example, if the board is labelled '7A04':
tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin
These files can also be used with the sysupgrade utility in stock images (add
SSH key in luci for root access).
Signed-off-by: Leon M. George <leon@georgemail.eu>
[fix sorting of definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
SoC: QCA9531
DRAM: 128MB DDR2
Flash: 16MB SPI-NOR
2 100MBit ethernet ports
2×2 2.4GHz on-board radio
miniPCIe slot that supports 5GHz radio
PoE 24V - 48V IEEE 802.3af optional
USB 2.0 header
Installation:
To install, start a tftp server in bin/targets/ath79/generic/ and use the
u-boot prompt over UART:
tftpboot 0x80500000 openwrt-ath79-generic-compex_wpj531-16m-squashfs-sysupgrade.bin
erase 0x9f030000 +$filesize
erase 0x9f680000 +1
cp.b $fileaddr 0x9f030000 $filesize
boot
The cpximg file can be used with sysupgrade in the stock firmware (add SSH key
in luci for root access).
Another way is to hold the reset button during power up or running 'cpximg' in
the u-boot prompt.
Once the last LED starts flashing regularly, a TFTP-server under 192.168.1.1
will accept the image appropriate for the board revision that is etched on the
board.
For example, if the board is labelled '7A04':
tftp -v -m binary 192.168.1.1 -c put openwrt-ath79-generic-compex_wpj531-16m-squashfs-cpximg-7A04.bin
MAC addresses:
<&uboot 0x2e010> *:cb (label)
<&uboot 0x2e018> *:cc
<&uboot 0x2e020> *:cd
<&uboot 0x2e028> *:ce
Only the first two are used (for ethernet), the WiFi modules have
separate (valid) addresses. The latter two addresses are not used.
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit title/message facelift, fix rssileds, add led aliases]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The WAC124 hardware appears to be identical to R6260/R6350/R6850.
SoC: MediaTek MT7621AT
RAM: 128M DDR3
FLASH: 128M NAND (Macronix MX30LF1G18AC)
WiFI: MediaTek MT7603 bgn 2T2R
MediaTek MT7615 nac 4T4R
ETH: SoC Integrated Gigabit Switch (1x WAN, 4x LAN)
USB: 1x USB 2.0
BTN: Reset, WPS
LED: Power, Internet, WiFi, USB (all green)
Installation:
The factory image can be flashed from the stock firmware web interface
or using nmrpflash. With nmrpflash it is also possible to revert to
stock firmware.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
This adds support for the Netgear R6080, aka Netgear AC1000.
The R6080 has almost the same hardware as the Netgear R6120,
aka Netgear AC1200, but it lacks the USB port, has only 8 MiB flash and
uses a different SERCOMM_HWID.
Specification:
SoC: MediaTek MT7628 (580 MHz)
Flash: 8 MiB
RAM: 64 MiB
Wireless: 2.4Ghz (builtin) and 5Ghz (MT7612E)
LAN speed: 10/100
LAN ports: 4
WAN speed: 10/100
WAN ports: 1
UART (57600 8N1) on PCB
Installation:
Flashing OpenWRT from stock firmware requires nmrpflash. Use an ethernet
cable to connect to LAN port 1 of the R6080, and power the R6080 off.
From the connected workstation, run
`nmrpflash -i eth0 -f openwrt-ramips-mt76x8-netgear_r6080-squashfs-factory.img`,
replacing eth0 with the appropriate interface (can be identified by
running `nmrpflash -L`). Then power on the R6080. After flashing has finished,
power cycle the R6080, and it will boot into OpenWRT. Once OpenWRT has been
installed, subsequent flashes can use the web interface and sysupgrade files.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[rebase and adjust for 5.4]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
switch-bcm53xx-mdio does not exists, use kmod-switch-bcm53xx-mdio
instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Tobias Schramm <tobleminer@gmail.com>
- Delete useless HDD presence inputs: they aren't buttons, and probably
they are outputs in the stock firmware.
- Change the Function Button keycode: the current one isn't mapped by
the kernel module.
- Use the recommended property names for the ethernet stuff.
- Add missing i2c pinmux.
- Minor cosmetic changes.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
All boards on xrx200 use builtin switch and there is no supported device
with external switch.
It was copy paste from xway subtarget and was added in commit 18b76c66fb.
Save 20.3 kB flash memory.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
This is fixed in 18.06, it appears again in 19.07.
Currently mt7628 sdcard driver do not support polling mode which is for
the device do not have card-detect pin to detect sd card insert. Without
this patch, device will not detect sdcard is inserted. This patch is a
fix of that.
Signed-off-by: Qin Wei <support@vocore.io>
Support Intel 10 Gigabit Ethernet Cards in x86/64 images by default.
This ensures that systems with cards such as the Intel x520 will work properly.
Signed-off-by: Gregory L. Dietsche <Gregory.Dietsche@cuw.edu>
With this change the LED subsystem is abused in the kernel to switch the
simswap. This change will be reverted, so we could use again the gpio
subsystem.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Add a module description for the new pcengnies-apu2 device driver.
This driver supports the front button and LEDs on the PC Engines
APUv2/APUv3 boards.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
In ath79, for several SoCs the console bootargs are defined to the
very same value in every device's DTS. Consolidate these definitions
in the SoC dtsi files and drop further redundant definitions elsewhere.
The only device without any bootargs set has been OpenMesh OM5P-AC V2.
This will now inherit the setting from qca955x.dtsi
Note that while this tidies up master a lot, it might develop into a
frequent pitfall for backports.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
chosen/bootargs are defined to the same value in device DTS files
that is already set in the SoC DTSI. Remove the redundant definitions.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for the AVM FRITZ!WLAN Repeater DVB-C
SOC: Qualcomm Atheros QCA9556
RAM: 64 MiB
FLASH: 16 MB SPI-NOR
WLAN: QCA9556 3T3R 2.4 GHZ b/g/n and
QCA9880 3T3R 5 GHz n/ac
ETH: Atheros AR8033 1000 Base-T
DVB-C: EM28174 with MaxLinear MXL251 tuner
BTN: WPS Button
LED: Power, WLAN, TV, RSSI0-4
Tested and working:
- Ethernet (correct MAC, gigabit, iperf3 about 200 Mbit/s)
- 2.4 GHz Wi-Fi (correct MAC)
- 5 GHz Wi-Fi (correct MAC)
- WPS Button (tested using wifitoggle)
- LEDs
- Installation via EVA bootloader (FTP recovery)
- OpenWrt sysupgrade (both CLI and LuCI)
- Download of "urlader" (mtd0)
Not working:
- Internal USB
- DVB-C em28174+MxL251 (depends on internal USB)
Installation via EVA bootloader (FTP recovery):
Set NIC to 192.168.178.3/24 gateway 192.168.178.1 and power on the device,
connect to 192.168.178.1 through FTP and sign in with adam2/adam2:
ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote MEDIA FLSH
ftp> put openwrt-sysupgrade.bin mtd1
Wait for "Transfer complete" together with the transfer details.
Wait two minutes to make sure flash is complete (just to be safe).
Then restart the device (power off and on) to boot into OpenWrt.
Revert your NIC settings to reach OpenWrt at 192.168.1.1
Signed-off-by: Natalie Kagelmacher <nataliek@pm.me>
[fixed sorting - removed change to other board -
prettified commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds supports for the NETGEAR R6200 V1
This device is mainlined in Linux as of 5.4
Specification:
- SOC: Broadcom BCM4718A1 (480 MHz)
- Flash: 16MB (Macronix MX25L128)
- RAM: 128MB DDR2
- SWITCH: BCM53125
- Ethernet: 5x GE (1 WAN + 4 LAN, Inverted order)
- WLAN 2.4G: In SOC
- WLAN 5GHz: miniPCIe card, BCM4352 (ID: 4360)
- USB: 1x USB 2.0 port (Type A)
- Buttons: Reset, WLAN, WPS
- LED: Amber for Power, others need a workaround
- UART: 1x UART on PCB
LED Issues: They are controlled by a 74HC164 via bit banging(GPIO 6/7)
Firmware Install Instructions
=============================
Using the device specific .chk, use that file to perform
a normal device upgrade in the OEM admin page.
Signed-off-by: Edward Matijevic <motolav@gmail.com>
This commit performs minor janitorial work to clean up some code
formatting for the Netgear R6120.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
This moves the trigger for the Netgear R6120's wlan2g_green LED from
base-files/etc/board.d/01_leds to the device-tree file.
This has been applied to R6120 based on findings for the very similar
Netgear R6080.
Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
[merge case in 01_leds, slightly adjust commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The DTS files in files-4.19 and files-5.4 are exactly identical
except for one file (armada-3720-uDPU.dts), which is only present
for 4.19, as it has been upstreamed before 5.4.
Since there is no point in maintaining all these identical files
twice, this patch moves them to the "files" directory, only keeping
the named exception to files-4.19.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The DTS files in files-4.19 and files-5.4 are exactly identical
except for one file (qcom-ipq4018-emr3500.dts), which is only
present for 5.4.
Since there is no point in maintaining all these identical files
twice, this patch moves them to the "files" directory.
If there ever was a new kernel with substantial DTS changes, a
new folder would need to be introduced anyway and could easily be
done.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The mwlwifi driver sets the default country code for EU (fi-
rmware region code 0x30) certified devices to FR (France),
not DE (Germany). Whilst this is a trivial fix, novice users
may not know how mwlwifi negatively reacts to a non-matching
country code and may leave the setting alone. Especially si-
nce it is under the advanced settings section in LuCI.
Relevant mwlwifi driver code:
0a550312dd
The mwlwifi driver readme states "Please don't change country
code and let mwlwifi set it for you." However, OpenWrt's current
behaviour does not adhere to this with its default, 'just flashed
from factory' setting for EU devices.
Signed-off-by: Jose Olivera <oliverajeo@gmail.com>
[rebase, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Upstream in commit f9f8f0c24203 ("crypto: ccp -- don't "select"
CONFIG_DMADEVICES") removed dependency on CONFIG_DMADEVICES symbol which
leads to build breakage of ccp crypto module, so fix this by adding that
symbol back in the kernel config.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The ADB P.DG AV4202N device has a wifi chipset connected via PCI. But the
PCI pinmux is missing and without it the wifi won't work properly.
Add the pinctrl_pci to enable the missing PCI pins for this device.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Currently it's not possible to tftpboot initramfs image on archer-c7-v5
as the image contains tplink-v1-header which leads to:
ath> bootm
## Booting image at 81000000 ...
Bad Magic Number
as U-Boot expects uImage wrapped image. This is caused by following
inheritance issue:
define Device/Init
KERNEL_INITRAMFS = $$(KERNEL)
define Device/tplink-v1
KERNEL := kernel-bin | append-dtb | lzma
KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | tplink-v1-header
define Device/tplink-safeloader
$(Device/tplink-v1)
define Device/tplink-safeloader-uimage
$(Device/tplink-safeloader)
KERNEL := kernel-bin | append-dtb | lzma | uImageArcher lzma
define Device/tplink_archer-c7-v5
$(Device/tplink-safeloader-uimage)
where tplink-v1 defines KERNEL_INITRAMFS with tplink-v1-header and it's
then used by all devices inheriting from tplink-safeloader. Fix this by
overriding KERNEL_INITRAMFS to KERNEL variable again.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The fritz 7312 does not support 1000 gbit. Advertising it makes it
worse. Some NIC will change to 1000 gibt and turn off and on again for
ever.
The previous patch in 36f628910b was only applied to the 4.19 file,
so let's just make it consistent with this patch.
Cc: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Inputs assigned to "mode select" switch on the side of the device
were missing linux,input-type property.
This would cause them do incorrectly generate EV_KEY events.
Fix this by setting the linux,input-type = <EV_SW> property on them.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Increase the SPI frequency for ELECOM WRC-1900GST and WRC-2533GST
to 40 MHz by updating the common DTSI file.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
[WRC-1900GST]
Acked-by: NOGUCHI Hiroshi <drvlabo@gmail.com>
[split patch, adjust commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link CPE610 v2 is an outdoor wireless CPE for 5 GHz with
one Ethernet port based on Atheros AR9344
Specifications:
- 560/450/225 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of DDR2 RAM
- 8 MB of SPI-NOR Flash
- 23dBi high-gain directional 2×2 MIMO antenna and a
dedicated metal reflector
- Power, LAN, WLAN5G green LEDs
- 3x green RSSI LEDs
Flashing instructions:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Andrew Cameron <apcameron@softhome.net>
This ports support for these devices from ar71xx.
Specification:
- System-On-Chip: Qualcomm Atheros QCA9533
- CPU/Speed: v3: 560 MHz, v4: 650 MHz
- Flash: 4096 KiB
- RAM: 32 MiB
- Ethernet: 1 port @ 100M
- Wireless: SoC-integrated: QCA9533 2.4GHz 802.11bgn
In contrast to the implementation in ar71xx (reset and WiFi button),
the device actually features reset and WPS buttons.
Flashing instructions:
Upload the ...-factory.bin file via OEM web interface.
TFTP Recovery:
1. Set PC to fixed IP address 192.168.0.66
2. Download *-factory.bin image and rename it to
wa801ndv3_tp_recovery.bin
3. Start a tftp server with the image file in its root directory
4. Turn off the router
5. Press and hold Reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time
the firmware should be transferred from the tftp server
8. Wait ~30 second to complete recovery.
TFTP recovery has only been tested with v3, and the Wiki states
that the procedure won't work for v4, which cannot be verified
or falsified at the moment.
Tested by Tim Ward (see forum):
https://forum.openwrt.org/t/ath79-support-for-tp-link-tl-wa901nd-v3-v4-v5/61246/13
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fix the switch LAN labels for the DGND3700v1/DGND3800B router,
the order is reversed.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[cut out of bigger patch, adjust commit title/message accordingly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Huawei Echolife HG622 has hardware controlled LAN LEDs.
Add the ephy led pinctrl to let the router show LAN activity on these
LEDs.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The status is set to "okay" for all devices on ar9344, so just move
this to the parent DTSI.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Define the kernel config symbol CONFIG_MFD_RB4XX_CPLD=n
to fix build breakage on non-mikrotik targets.
The driver was added for all ath79, but the symbol was only
defined for mikrotik subtarget.
Fixes: fa70b3a4bb ("ath79: add Mikrotik rb4xx series drivers")
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
[rearrange commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
CONFIG_HZ_100 is not set to "y" in generic config anymore since
3a761c90af ("treewide: Don't diverge from upstream default HZ
settings on 4.19"), so we don't need to disable it anymore either.
This was the only remaining case in the entire tree.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently I'm unable to boot initramfs image with `console=ttyS0,115200`
kernel commandline as the kernel commandline mangling resets kernel
commandline if there is no `root=` option provided, efectively clearing
whatever I pass to the kernel, making the `root=` option mandatory.
So if the kernel commandline mangling is not appropriate just leave the
kernel commandline as it is.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The Sercomm devices don't need the jffs2 cleanmarkers for the kernel
partition. With the stock firmware they are only added when the
bootloader partition is upgraded.
Furthermore, on the Sercomm H500-s, the specific cfe_jffs2_upgrade_tar
function causes OOB corruption. As a result of this, combined with the
nature of the mtdsplit driver, the upgrade procedure ends in a bricked
device.
Use the generic nand_do_upgrade provided by the OpenWrt common functions.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The uci config section network.globals set up in /bin/config_generate
will only be created if /proc/sys/net/ipv6 exists.
Correspondingly, lacking IPv6 support, the command
uci set network.globals.packet_steering=1
will fail with "uci: Invalid argument" as the network.globals config
has not been set up.
Fix that by adding the setup there as well.
While at it, limit the uci commit to the network config file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
- SoC: Atheros AR9344
- RAM: 64MB
- Storage: 8 MB SPI NOR
- Wireless: 2.4GHz N based built into SoC
- Ethernet: 1x 10/100 Mbps with 24V POE IN, 1x 10/100 Mbps
Installation:
Flash factory image through stock firmware WEB UI
or through TFTP
To get to TFTP recovery just hold reset button while powering on for
around 4-5 seconds and release.
Rename factory image to recovery.bin
Stock TFTP server IP:192.168.0.100
Stock device TFTP adress:192.168.0.254
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the MikroTik RouterBOARD RB493G, ported
from the ar71xx target.
See https://routerboard.com/RB493G for details
Specification:
- SoC Qualcomm Atheros AR7161
- RAM: 256 MiB
- Storage: 128MiB NAND
- Ethernet: 9x 1000/100/10 Mbps
- USB 1x 2.0 / 1.0 type A
- PCIe: 3x Mini slot
- MicroSD slot
Working:
- Board/system detection
- Ethernet
- SPI
- NAND
- LEDs
- USB
- Sysupgrade
Enabled (but untested due to lack of hardware):
- PCIe - ath79_pci_irq struct has the slot/pin/IRQ mappings if needed
Installation methods:
- tftp boot initramfs image, scp then flash via "sysupgrade -n"
- nand boot existing OpenWrt, scp then flash via "sysupgrade -n"
Notes:
- initramfs image will not work if uncompressed image size over ~8.5Mb
- The "rb4xx" drivers have been enabled
Signed-off-by: Christopher Hill <ch6574@gmail.com>
This adds 3 Mikrotik rb4xx series drivers as follows:
rb4xx-cpld: This is in the mfd subsystem, and is the parent CPLD device
that interfaces between the SoC SPI bus and its two children below.
rb4xx-gpio: This is the GPIO expander.
rb4xx-nand: This is the NAND driver.
The history of this code comes in three phases.
1. The first is a May 2015 attempt to push the equivalient ar71xx rb4xx
drivers upstream. See https://lore.kernel.org/patchwork/patch/940880/.
Module-author: Gabor Juhos <juhosg@openwrt.org>
Module-author: Imre Kaloz <kaloz@openwrt.org>
Module-author: Bert Vermeulen <bert@biot.com>
2. Next several ar71xx patches were applied bringing the code current.
commit 7bbf4117c6
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
commit af79fdbe4a
commit 889272d92d
commit e21cb649a2
commit 7c09fa4a74
Signed-off-by: Felix Fietkau <nbd@nbd.name>
3. Finally a heavy refactor to split the driver into the three new
subsystems, and updated to work with the device tree configuration, plus
updates and review feedback incorporated
Reviewed-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Christopher Hill <ch6574@gmail.com>
