Commit Graph

49075 Commits

Author SHA1 Message Date
Christian Lamparter
890bb54d7f ipq40xx: fix DTS warning in qcom-ipq4019-cm520-79f.dts
.dts:121.4-14: Warning (reg_format): /led_spi/led_gpio@0:reg: \
	property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
.dtb: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
.dtb: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
.dtb: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
.dts:119.24-126.5: Warning (avoid_default_addr_size): /led_spi/led_gpio@0: \
	Relying on default #size-cells value

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
0e4092cbad bcm53xx: add Cisco Meraki MR32
This patch adds support for Cisco Meraki MR32.
The unit was donated by Chris Blake. Thank you!

WARNING:
Only the 1x1:1 abgn Air Marshal WIPS wifi is currently supported by b43:
 b43-phy2: Found PHY: Analog 9, Type 4 (N), Revision 16
 b43-phy2: Found Radio: Manuf 0x17F, ID 0x2057, Revision 9, Version 1
 b43-phy2: Loading firmware version 784.2 (2012-08-15 21:35:19)
 and only as 802.11ABG!

while WIFI1 and WIFI2 (both BCM4352) are not:
 b43-phy0: Broadcom 4352 WLAN found (core revision 42)
 b43-phy0 ERROR: FOUND UNSUPPORTED PHY (Analog 12, Type 11 (AC), Revision 1)

Hardware Highlights:

SoC:	Broadcom BCM53016A1 (1 GHz, 2 cores)
RAM:	128 MiB
NAND:	128 MiB Spansion S34ML01G2 (~114 MiB useable)
ETH:	1GBit Ethernet Port - PoE
WIFI1:	Broadcom BCM43520 an+ac (2x2:2 - id: 0x4352)
WIFI2:	Broadcom BCM43520 bgn (2x2:2 - id: 0x4352)
WIFI3:	Broadcom BCM43428 abgn (1x1:1 - id: 43428)

BLE:	Broadcom BCM20732 (ttyS1)
LEDS:   1 x Programmable RGB Status LED (driven by a PWM)
	1 x White LED (GPIO)
	1 x Orange LED Fault Indicator (GPIO)
	2 x LAN Activity / Speed LEDs (On the RJ45 Port)
BUTTON: one Reset button
MISC:   AT24C64 8KiB EEPROM (i2c - stores Ethernet MAC + Serial#!)
	ina219 hardware monitor (i2c)
	Kensington Lock

SERIAL:
	WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
	The Serial setting is 115200-8-N-1. The board has a populated
	right angle 1x4 0.1" pinheader.
	The pinout is: VCC, RX, TX, GND. (Use a multimeter)

Flashing needs a serial adaptor (due to the lack of a working dropbear on
the original firmware).

This flashing procedure for the MR32 was tested with firmware:
"r23-149867:150252-aacharya".

0. Create a seperate Ethernet LAN which does not have access to the internet.
   Ideally use 192.168.1.2 for your PC. Make sure to reserve 192.168.1.1 it
   will be used later on by the OpenWrt firmware. The original Meraki firmware
   will likely try to setup the network via DHCP Discovery, so make sure your
   PC is running a DHCP-Server (i.e.: dnsmasq)
   '# dnsmasq -i eth# -F 192.168.1.5,192.168.1.50
   Furthermore, the PC needs a supported ssh/http/ftp server in order to
   retrieve the initramfs + dtb file

1. Disassemble the MR32 device by removing all screws (4 screws are located
   under the 4 rubber feets!) and prying open the plastic covers without
   breaking the plastic retention clips. Once inside, remove all the screws
   on the outer metal shielding to get to the PCB. It's not necessary to
   remove the antennas!

2. Connect the serial cable to the serial header.

3. Partially reassemble the outer metal shielding to ensure that the SoC
   has a proper heat sink.

4. Connect the Ethernet patch cable to the device and the power cable.

5. Wait for the device to boot and enter the root shell.
   (rooting is not discussed in detail here please refer to
   Chris Blake - "pwning the meraki mr18" blog post:
   <https://servernetworktech.com/2016/02/pwning-the-meraki-mr18/>
   (The same method works with the MR32's r23-149867:150252-aacharya)

   Wait for the MR32 to enter the "<Meraki>" prompt and enter:
   <Meraki> odm serial_num read
   (Verify that it matches what's on the S/N Sticker on the back!)
   <Meraki> odm serial_num write Q2XX-XXXX-XXXV
   <Meraki> odm serial_num read
   (Verify that the S/N has changed - and the LED start to flash)

   now to flash the firmware:
   <Meraki> odm firmware part.safe "http://192.168.1.2/mr32-initramfs.bin"

Once OpenWrt booted use sysupgrade to permanently install
OpenWrt. To do this: Download the latest sysupgrade.bin file
for the MR32 to the device and use sysupgrade *sysupgrade.bin
to install it.

WARNING: DO NOT DELETE the "storage" ubi volume!

To flash later MR32 Firmwares like r25-201804051805-G885d6d78-dhow-rel
requires in-circut-i2c tools to access the I2C EEPROM AT24C64 next to
the SoC. The idea is pretty much the same as from Step 5 from above:
Change the serial number to Q2XXXXXXXXXV (should be around 0x7c), then
attach a serial cable, ethernet (but make sure the device can't reach
the internet!) hit "s" (the small s!) during boot to enter the root-shell
and add the following commands to the /storage/config there:

serial_allow_odm true
serial_access_enabled true
serial_access_check false
valid_config true

and then hit exit to let it finish booting.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
1291274335 kernel: package bcm53xx i2c module
The BCM5301x SoCs do have i2c. Since this is only
being used by the Meraki MR32, this will be packaged
as a module.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
abe46d5002 kernel: add default for new config symbols
Provide disabled defaults for I2C_SLAVE_EEPROM and IPMB_DEVICE_INTERFACE.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
5f610ec4b8 bcm53xx: backport uart2 and pcie2 device-nodes
These have made their way into -next. This patch
also includes the portion of the bcm53xx kernel
patch refreshes as the hunks in
302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch
moved slightly due to the added nodes.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:34 +02:00
Christian Lamparter
c6d9a2ac59 bcm53xx: enable PWM for bcm53xx
The Meraki MR32 (BCM53016A1) uses the pwm to drive the
tricolor LED. The driver has been available in upstream
for a long time. Only the Device-Tree definition was
missing, but it has been queued recently.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:33 +02:00
Christian Lamparter
f6fbc39706 build: define PWM_SUPPORT arch feature flag
As the PWM has its own sub-system in the Linux kernel,
I think it should be handled in the same way as GPIO, RTC, PCI...

This patch introduces a specific feature flag "pwm" and the
"leds-pwm" kernel module as the first customer.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:33 +02:00
Christian Lamparter
fed1788689 scripts: mkits.sh make it possible to specify fdt@#
Some bootloaders are really keen on just one special
fdt in a multi-image fit image. This is a problem, because
currently this is fixed to "fdt@1".

This patch introduces a new device variable:
DEVICE_FDT_NUM that allows to specify the right
fdt number.

If the value is absent "1" will be chosen.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:32:33 +02:00
Hans Geiblinger
a9071d02b5 ipq40xx: Add support for Linksys MR8300 (Dallas)
The Linksys MR8300 is based on QCA4019 and QCA9888
and provides three, independent radios.
NAND provides two, alternate kernel/firmware images
with fail-over provided by the OEM U-Boot.

Hardware Highlights:

SoC: IPQ4019 at 717 MHz (4 CPUs)
RAM: 512MB RAM

SoC:	Qualcomm IPQ4019 at 717 MHz (4 CPUs)
RAM:	512M DDR3
FLASH:	256 MB NAND (Winbond W29N02GV, 8-bit parallel)
ETH:	Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks)
BTN:	Reset and WPS
USB:	USB3.0, single port on rear with LED
SERIAL:	Serial pads internal (unpopulated)
LED:	Four status lights on top + USB LED
WIFI1:	2x2:2 QCA4019 2.4 GHz radio on ch. 1-14
WIFI2:  2x2:2 QCA4019 5 GHz radio on ch. 36-64
WIFI3:  2x2:2 QCA9888 5 GHz radio on ch. 100-165

Support is based on the already supported EA8300.
Key differences:
	EA8300 has 256MB RAM where MR8300 has 512MB RAM.
	MR8300 has a revised top panel LED setup.

Installation:
"Factory" images may be installed directly through the OEM GUI using
URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1)

Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com>
[copied Hardware-highlights from EA8300. Fixed alphabetical order.
fixed commit subject, removed bogus unit-address of keys,
fixed author (used Signed-off-By to From:) ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:31:51 +02:00
Tomasz Maciej Nowak
e24635710c ipq40xx: add support for Luma Home WRTQ-329ACN
Luma Home WRTQ-329ACN, also known as Luma WiFi System, is a dual-band
wireless access point.

Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 2 MB SPI NOR
       128 MB SPI NAND
WIFI: 2.4 GHz 2T2R integrated
      5 GHz 2T2R integrated
Ethernet: 2x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
Bluetooth: 1x 4.0 CSR8510 A10, connected to USB bus
LEDS: 16x multicolor LEDs ring, controlled by MSP430G2403 MCU
Buttons: 1x GPIO controlled
EEPROM: 16 Kbit, compatible with AT24C16
UART: row of 4 holes marked on PCB as J19, starting count from the side
      of J19 marking on PCB
      1. GND, 2. RX, 3. TX, 4. 3.3V
      baud: 115200, parity: none, flow control: none

The device supports OTA or USB flash drive updates, unfotunately they
are signed. Until the signing key is known, the UART access is mandatory
for installation. The difficult part is disassembling the casing, there
are a lot of latches holding it together.

Teardown
Prepare three thin, but sturdy, prying tools. Place the device with back
of it facing upwards. Start with the wall having a small notch. Insert
first tool, until You'll feel resistance and keep it there. Repeat the
procedure for neighbouring walls. With applying a pressure, one edge of
the back cover should pop up. Now carefully slide one of the tools to
free the rest of the latches.
There's no need to solder pins to the UART holes, You can use hook clips,
but wiring them outside the casing, will ease debuging and recovery if
problems occur.

Installation
1. Prepare TFTP server with OpenWrt initramfs image.
2. Connect to UART port (don't connect the voltage pin).
3. Connect to LAN port.
4. Power on the device, carefully observe the console output and when
   asked quickly enter the failsafe mode.
5. Invoke 'mount_root'.
6. After the overlayfs is mounted run:
     fw_setenv bootdelay 3
   This will allow to access U-Boot shell.
7. Reboot the device and when prompted to stop autoboot, hit any key.
8. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
   'setenv' to do that, then run following commands:
     tftpboot 0x84000000 <openwrt_initramfs_image_name>
     bootm 0x84000000
   and wait till OpenWrt boots.
9. In OpenWrt command line run following commands:
     fw_setenv openwrt "setenv mtdids nand1=spi_nand; setenv mtdparts mtdparts=spi_nand:-(ubi); ubi part ubi; ubi read 0x84000000 kernel; bootm 0x84000000"
     fw_setenv bootcmd "run openwrt"
10. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
    with:
     ubirmvol /dev/ubi0 -N ubi_rootfs
     sysupgrade -v -n /tmp/<openwrt_sysupgrade_image_name>
11. After flashing, the access point will reboot to OpenWrt, then it's
    ready for configuration.

Reverting to OEM firmware
1. Execute installation guide steps: 1, 2, 3, 7, 8.
2. In OpenWrt command line run following commands:
     ubirmvol /dev/ubi0 -N rootfs_data
     ubirmvol /dev/ubi0 -N rootfs
     ubirmvol /dev/ubi0 -N kernel
     ubirename /dev/ubi0 kernel1 kernel ubi_rootfs1 ubi_rootfs
     ubimkvol /dev/ubi0 -S 34 -N kernel1
     ubimkvol /dev/ubi0 -S 320 -N ubi_rootfs1
     ubimkvol /dev/ubi0 -S 264 -N rootfs_data
     fw_setenv bootcmd bootipq
3. Reboot.

Known issues
The LEDs ring doesn't have any dedicated driver or application to control
it, the only available option atm is to manipulate it with 'i2cset'
command. The default action after applying power to device is spinning
blue light. This light will stay active at all time. To disable it
install 'i2c-tools' with opkg and run:
 i2cset -y 2 0x48 3 1 0 0 i
The light will stay off until next cold boot.

Additional information
After completing 5. step from installation guide, one can disable asking
for root password on OEM firmware by running:
 sed -e 's/root/root::/' -i /etc/passwd
This is useful for investigating the OEM firmware. One can look
at the communication between the stock firmware and the vendor's
cloud servers or as a way of making a backup of both flash chips.
The root password seems to be constant across all sold devices.
This is output of 'led_ctl' from OEM firmware to illustrate
possibilities of LEDs ring:

Usage: led_ctl [status | upgrade | force_upgrade | version]
       led_ctl solid    COLOR <brightness>
       led_ctl single   COLOR INDEX <brightness 0 - 15>
       led_ctl spinning COLOR <period 1 - 16 (lower = faster)>
       led_ctl fill     COLOR <period 1 - 16 (lower = faster)>
                                             ( default is 5 )
       led_ctl flashing COLOR <on dur 1 - 128>  <off dur 1 - 128>
                              (default is  34)  ( default is 34 )
       led_ctl pulsing  COLOR
COLOR: red, green, blue, yellow, purple, cyan, white

Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[squash "ipq-wifi: add BDFs for Luma Home WRTQ-329ACN" into commit,
changed ubi volumes for easier integration, slightly reworded
commit message, changed ubi volume layout to use standard names all
around]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 19:30:19 +02:00
Brian Norris
03bc9b0002 ipq40xx: add open-drain support to pinctrl-msm
Submitted upstream. Shouldn't affect existing devices, but enables new
device support.

https://lore.kernel.org/linux-gpio/20200703080646.23233-1-computersforpeace@gmail.com/

Currently queued for-next:
https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl.git/commit/?h=for-next&id=13355ca35cd16f5024655ac06e228b3c199e52a9

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
[refresh patch]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2020-09-25 18:43:09 +02:00
Yousong Zhou
7dc78d1d28 dnsmasq: fix handling ignore condition for dnssec
It should return false to indicate that the option should not be ignored

Fixes 064dc1e8 ("dnsmasq: abort when dnssec requested but not
available")

Reported-by: Sami Olmari <sami@olmari.fi>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
2020-09-25 10:31:36 +08:00
W. Michael Petullo
d20007ce91 dnsmasq: support tftp_unique_root in /etc/config/dhcp
The TFTP server provided by dnsmasq supports serving a select boot image
based on the client's MAC or IP address. This allows an administrator
to activate this feature in /etc/config/dhcp. Here is an example
/etc/config/dhcp that configures dnsmasq with --tftp-unique-root=mac:

...

config dnsmasq
	option enable_tftp 1
	option tftp_root /usr/libexec/tftpboot
	option tftp_unique_root mac

config boot router
	option serveraddress 192.168.1.1
	option servername tftp.example.com
	option filename openwrt-initramfs-kernel.bin

...

With this configuration, dnsmasq will serve
/usr/libexec/tftpboot/00-11-22-33-44-55/openwrt-initramfs-kernel.bin to
the client with MAC address 00:11:22:33:44:55.

Signed-off-by: W. Michael Petullo <mike@flyn.org>
2020-09-24 22:38:37 +02:00
Hans Dedecker
ad3044c424 vxlan: fix rsc config option
Fix route short circuit config option; fixes commit 036221ce5a

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2020-09-24 22:14:36 +02:00
John Audia
3ea1b5b745 kernel: bump 5.4 to 5.4.67
All modifications made by update_kernel.sh

Build system: x86_64
Build-tested: ipq806x, lantiq/xrx200 and ath79/generic
Run-tested: ipq806x (R7800), lantiq (Easybox 904 xDSL)

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
[add test on lantiq]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-24 18:53:23 +02:00
Hans Dedecker
036221ce5a vxlan: add extra config options
Add config options:
  srcportmin/srcportmax : range of port numbers to use as  UDP source ports
                          to communicate to the remote VXLAN tunnel endpoint
  ageing                : lifetime in seconds of FDB entries learnt by the kernel
  maxaddress            : maximum number of FDB entries
  learning              : enable/disable entering unknown source link layer addresses
                          and IP addresses into the VXLAN device FDB.
  rsc                   : enable/disable route short circuit
  proxy                 : enable/disable ARP proxy
  l2miss                : enable/disable netlink LLADDR miss notifications
  l3miss                : enable/disable netlink IP ADDR miss notifications
  gbp                   : enable/disable the Group Policy extension

Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
2020-09-23 21:45:15 +02:00
J. Scott Heppler
620f9c7734 ramips: add support for Linksys EA7300 v2
This submission relied heavily on the work of
Santiago Rodriguez-Papa <contact at rodsan.dev>

Specifications:

*  SoC:            MediaTek  MT7621A            (880  MHz  2c/4t)
*  RAM:            Winbond W632GG6MB-12         (256M  DDR3-1600)
*  Flash:          Winbond W29N01HVSINA         (128M  NAND)
*  Eth:            MediaTek  MT7621A            (10/100/1000  Mbps  x5)
*  Radio:          MT7603E/MT7615N              (2.4  GHz  &  5  GHz)
                     4  antennae:  1  internal  and  3  non-deatachable
*  USB:            3.0  (x1)
*  LEDs:
          White    (x1  logo)
          Green    (x6  eth  +  wps)
          Orange   (x5,  hardware-bound)
*  Buttons:
          Reset    (x1)
          WPS      (x1)

Installation:

Flash factory image through GUI.

This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.

Reverting to factory firmware:

Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.

Signed-off-by: J. Scott Heppler <shep971@centurylink.net>
2020-09-23 12:17:32 +02:00
Felix Fietkau
127ca3c631 mt76: update to the latest version
73301065ac32 mt76: mt7615: reduce maximum VHT MPDU length to 7991
8c47ed12c2be mt76: mt7915: add offchannel condition in switch channel command
1449e602fa10 mt76: Convert to DEFINE_SHOW_ATTRIBUTE
b22977c2727d mt76: mt7663s: remove max_tx_fragments limitation

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-23 08:39:26 +02:00
Felix Fietkau
4bd7689d85 mac80211: update sta connection monitor regression fix
Reset the connection monitor on all acked frames

Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-23 08:39:26 +02:00
Adrian Schmutzler
0cfdc7d446 target: update SPDX license names
SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to
GPL-2.0-or-later. Reflect that in the SPDX license headers.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-22 20:58:26 +02:00
Paul Spooren
8be2eb3b9b scripts: update SPDX license names
SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to
GPL-2.0-or-later. Reflect that in the SPDX license headers.

Signed-off-by: Paul Spooren <mail@aparcar.org>
[adjust commit title, update remaining files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-22 20:36:04 +02:00
Paul Spooren
e8f61bf50d ath79: remove DTS from ATH79 target name
The legacy ar71xx target is removed and multiple targets use DTS now, so
there is no need to point that out for ATH79 specifically.

Signed-off-by: Paul Spooren <mail@aparcar.org>
2020-09-22 20:29:24 +02:00
David Bauer
c5eea362f3 hostapd: ubus: make (B)SSID optional for neighbor report
Make the BSSID and SSID fields optional when configuring a neighbor
report into hostapd.

Both options can now be an empty string. For the BSSID, the first 6 byte
are copied from the neighbor report. For the SSID, the SSID for the
affected hostapd BSS is used.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-22 17:41:10 +02:00
David Bauer
560e54c69e hostapd: ubus: send notification instead of event
Rafal Milecki pointed out that ubus events are meant for low-level ubus
events only (e.g. addition or removal of an object). Higher level
events should happen as notifications on the ubus object itself.

Dispatch BSS events on the main hostapd ubus object instead of
publishing them as ubus events.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-22 17:40:08 +02:00
Chuanhong Guo
006cd489f0 mediatek: mt7622: select bluetooth module instead of firmware
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-09-22 21:13:54 +08:00
Chuanhong Guo
20f2bd044a mediatek: build btmtkuart as a kernel module
bluetooth on mt7622 needs a firmware to start. It can't be built-in or
it tries to load firmware before rootfs is mounted, and then fails.
build it as a kernel module to fix that.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
2020-09-22 21:07:50 +08:00
David Bauer
d643b10a76 hostapd: ubus: fix infinite loop when configuring RRM NR
The return-code was set, however it was never returned, nor was
the loop interrupted.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-21 21:27:56 +02:00
David Bauer
8e7aa739fb hostapd: send procd event on BSS update
Dispatch ubus events also to procd in order to trigger service reloads
on hostapd updates.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-21 21:26:27 +02:00
David Bauer
6254af0c37 hostapd: send ubus event on BSS update
hostapd will emit a ubus event with the eventname hostapd.<ifname>.<event>
when adding, removing or reloading a BSS.

This way, services which install state (for example the RMM neighbor
list) can on-demand reinstall this information for the BSS without
polling this state.

Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-21 21:26:12 +02:00
Stijn Segers
ec80139629 odhcpd: number UCI defaults script
UCI defaults scripts are supposed to be numbered, but odhcpd's lacked numbering, which
turned out to mess up my custom scripts numbered 9[0-9]_*. The idea is to have high number
(custom) scripts executed last. Jow confirmed numbering is the default case, not the
exception (thanks).

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2020-09-21 20:59:40 +02:00
Daniel Golle
236e79abb7 policycoreutils: fix ALTERNATIVES install location
Fixes: 7817c831ef ("policycoreutils: break into smaller packages")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-09-21 18:58:14 +01:00
Daniel Golle
7817c831ef policycoreutils: break into smaller packages
Instead of vaguely describing dependencies in the package description
actually split-up into individual packages, each with their
dependencies expressed accurately.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-09-21 18:40:38 +01:00
Daniel Golle
81d895d1f1 libselinux: split utility packages and add PKG_LICENSE
Split utility packages similar to coreutils in packages feed, adding
ALTERNATIVES for those which are also provided by busybox-selinux.
Also add missing license information.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2020-09-21 18:40:38 +01:00
Felix Fietkau
1c6d45644a mac80211: fix regression in station connection monitor optimization
When the nulldata frame was acked, the probe send count needs to be reset,
otherwise it will keep increasing until the connection is considered dead,
even though it fine.

Reported-by: Georgi Valkov <gvalkov@abv.bg>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
2020-09-21 17:56:31 +02:00
Rui Salvaterra
90853439a1 zram-swap: explicitly use mkswap/swapon/swapoff from /sbin
The required BusyBox applets are enabled by default, so we can rely on them
being present in the system. This way, we make sure there are no conflicts
with less featured variants of these same applets which might also be
present in the system.

Fixes: 0bd7dfa3ed ("zram-swap: enable swap discard")

Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[wrap commit description]
Signed-off-by: David Bauer <mail@david-bauer.net>
2020-09-20 17:52:25 +02:00
Davide Fioravanti
cd36c0d2f0 mac80211: select the first available channel for 5GHz interfaces
Some 5GHz wifi interfaces, especially in Tri-band routers, can't use
channel 36. In these cases, the default configuration for 5GHz
interfaces, once enabled, doesn't work.

This patch selects the first non-disabled channel for 5GHz interfaces.

Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
2020-09-20 17:52:25 +02:00
David Woodhouse
7190fb2da4 mediatek: mt7623: use bash for generating bootable images
It turns out that 'echo -e' isn't portable; it doesn't work in the dash
builtin echo and Ubuntu users are complaining.

I can't even get octal (specified by POSIX) to work consistently because
those  variants of 'echo' which *do* support -e don't seem to interpret
octalwithout it.

I could switch to /bin/echo but using -e with that isn't actually
portable *either* even though it works today.

For now just stick with bash, and use its builtin. We may end up using
something else entirely; perhaps perl.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-09-19 13:39:29 +01:00
David Woodhouse
d10b738c4b mediatek: fix missing pause on switch port for Banana Pi R2
This causes rx drops when running iperf.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-09-19 13:39:29 +01:00
David Woodhouse
9e7369d37e mediatek: mt7623n-preloader: add preloader for Banana Pi R64
We want to be able to make full system images for this system too, just
as we now can for the MT7623 platforms.

The package directory (mt7623n) is now a bit misnamed as it's overly
specific, but the precise set of platforms which we support this way
is evolving and we'll fix it up when the dust settles and we know what
nomenclature makes most sense.

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2020-09-19 13:39:29 +01:00
Adrian Schmutzler
95c9df7971 ipq806x: fix support of Edgecore ECW5410 support
This fixes several stylistic and functional errors of the recently
added Edgecore ECW5410:

  - fix call in 11-ath10k-caldata
  - use hex notation in 11-ath10k-caldata
  - remove redundant definitions from DTS that are already in DTSI
  - use proper sorting in image/Makefile
  - use DEVICE_VENDOR/DEVICE_MODEL instead of DEVICE_TITLE
  - use SOC instead of DEVICE_DTS

Fixes: 59f0a0fd83 ("ipq806x: add Edgecore ECW5410 support")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-19 13:32:11 +02:00
John Audia
770a9c6787 kernel: bump 5.4 to 5.4.66
All modifications made by update_kernel.sh/no manual intervention needed

Run-tested: ipq806x (R7800), ath79 (Archer C7v5), x86/64

No dmesg regressions, everything appears functional

Signed-off-by: John Audia <graysky@archlinux.us>
[add run test from PR]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-19 12:41:29 +02:00
John Thomson
bf2870c1d9 kernel: fix mtd partition erase < parent_erasesize writes
This bug applied where mtd partition end address,
or erase start address, was not cleanly divisible by parent mtd erasesize.

This error would cause the bits following the end of the partition
to the next erasesize block boundary to be erased,
and this partition-overflow data to be written to the partition erase
address (missing additional partition offset address)
of the mtd (top) parent device.

Fixes: FS#2428

Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[shorten commit title, add Fixes, fix kernel 4.19 as well]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2020-09-19 12:41:29 +02:00
Andre Heider
8cfb839907 arm-trusted-firmware-mvebu: add support for espressobin
Use build variants to cover all 11 hardware options [0]:
espressobin-512mb
espressobin-v3-v5-1gb-1cs
espressobin-v3-v5-1gb-1cs-emmc
espressobin-v3-v5-1gb-2cs
espressobin-v3-v5-1gb-2cs-emmc
espressobin-v3-v5-2gb
espressobin-v3-v5-2gb-emmc
espressobin-v7-1gb
espressobin-v7-1gb-emmc
espressobin-v7-2gb
espressobin-v7-2gb-emmc

CLOCKSPRESET is set to CPU_800_DDR_800 for all builds, which is the only
stable configuration. That actually matches what Globalscale shipped as
CPU_1000_DDR_800 combined with kernel versions < v4.19.42. [1][2].

[0] https://github.com/ARM-software/arm-trusted-firmware/blob/master/docs/plat/marvell/armada/build.rst
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=8db82563451f976597ab7b282ec655e4390a4088
[2] https://forum.armbian.com/topic/10335-espressobin-update-to-585-results-in-kernel-panic/?tab=comments#comment-79916

Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-09-18 21:42:06 +02:00
Andre Heider
f6378b9e53 arm-trusted-firmware-mvebu: update a3700-utils
Update to current head of the branch A3700_utils-armada-18.12-fixed:
0967979 ddr: Add DDR3 2CS layout for EspressoBin v5 2GB board
486523e ddr: fix typo for ESPRESSObin 2GB layout
490b2b3 TBB: Fix building for Crypto++ 6.0 and later
0141dd1 TBB: Split INCDIR from LIBDIR

Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-09-18 21:42:06 +02:00
Andre Heider
65c1c91942 arm-trusted-firmware-mvebu: update to v2.3
Switch to release tarballs and add missing license information while
here.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-09-18 21:42:06 +02:00
Andre Heider
75e9d8e6e7 arm-trusted-firmware-mvebu: install to own subdir
Lift the dependency on the build order, where flash-image.bin may be missing
from the u-boot dir.

While at it, also install the uart images for rescue purposes.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-09-18 21:42:06 +02:00
Andre Heider
53065b2dee arm-trusted-firmware-mvebu: fix compiler spam
Gets rid of these warnings:
cc1: note: someone does not honour COPTS correctly, passed 0 times

Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-09-18 21:42:06 +02:00
Andre Heider
847b5927c6 arm-trusted-firmware-mvebu: reuse default prepare target
Don't wipe internal state files, fixes e.g. refreshing patches.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-09-18 21:42:05 +02:00
Andre Heider
72bb66caad uboot-mvebu: add support for espressobin
This builds two u-boot binaries: one for boards without eMMC and one
with.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-09-18 21:42:05 +02:00
Andre Heider
ae2e521b34 uboot-mvebu: update to v2020.10-rc4
TODO: switch to release v2020.10 once released.

Remove one merged patch, refresh the rest.

Signed-off-by: Andre Heider <a.heider@gmail.com>
2020-09-18 21:42:05 +02:00