Commit Graph

7 Commits

Author SHA1 Message Date
Martin Weinelt
1cd945ea22
ramips: fix leds on GL.iNet GL-MT300N-V2
The WAN LED now shows the link state. It's color is green,
not blue.

Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
(cherry picked from commit 0411813c6f)
2018-12-07 21:41:56 +01:00
Mathias Kresin
446dccc000 ramips: fix GL-MT300N-V2 SoC compatible
According to abbfcc8525 ("ramips: add support for GL-inet
GL-MT300N-V2") the board has a MediaTek MT7628AN. Change the SoC
compatible to match the used hardware.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2018-08-23 22:44:47 +02:00
Benjamin Valentin
2d8eeca842 ramips: enable power LED and second uart on GL-MT300N-V2
The device has a second uart accessible via pin headers, so enable it.

There is also a green power led which was not enabled previously.
Enable it too and use it as status LED.

Signed-off-by: Benjamin Valentin <benjamin.valentin@volatiles.de>
2018-02-23 07:54:29 +01:00
Mathias Kresin
95fe3c51e5 ramips: fix polarity in gpio-export node
If we need to set the initial output value to GPIOF_OUT_INIT_HIGH (1) to
enable something, the pin is ACTIVE_HIGH. The same applies to
GPIOF_OUT_INIT_LOW (0) and ACTIVE_LOW.

Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-12-18 09:32:27 +01:00
L. D. Pinney
70b192f573 ramips: update device tree source files
Use the GPIO dt-bindings macros and add compatible strings in the
ramips device tree source files.

Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-08-03 19:37:40 +02:00
John Marrett
4531bc4267 ramips: fix GL-inet GL-MT300N-V2 WAN/LAN MAC address
Correct MAC address lookup to appropriate offset based on vendor
source.

Override the WAN MAC to use the same address as LAN. The switch driver
increments the base MAC address for the WAN vlan but the stock firmware
uses the same MAC address for all interfaces.

Based on vendor source commit
https://github.com/domino-team/lede-1701/commit/efb0518

Signed-off-by: John Marrett <johnf@zioncluster.ca>
2017-07-15 07:02:59 +02:00
Kyson Lok
abbfcc8525 ramips: add support for GL-inet GL-MT300N-V2
This patch adds supports for the GL-inet GL-MT300N-V2.

Specification:
- SoC: MediaTek MT7628AN
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR
- Ethernet: 1 x WAN (100 Mbps) and 1 x LAN (100 Mbps)
- USB: 1 x USB 2.0 port
- Button: 1 x switch button, 1 x reset button
- LED: 3 x LEDS (system power led is not GPIO controller)
- UART: 1 x UART on PCB (JP1: 3.3V, RX, TX, GND)

Installation through Luci:
- The original firmware is LEDE, so both LuCI or sysupgrade can be used.
- Do not keep settings, for sysupgrade please use the -n option.

Installation through bootloader webserver:
- Plug power and hold reset button until red LED blink to bright.
- Install sysupgrade image using web interface on 192.168.1.1.

Signed-off-by: Kyson Lok <kysonlok@gmail.com>
[match maximum image size with firmware partition]
Signed-off-by: Mathias Kresin <dev@kresin.me>
2017-05-26 08:04:15 +02:00