Rework patch 681-NET-add-mtd-mac-address-support to implement
only the function to read the mac-address from mtd.
Generalize mtd-mac-address-increment function so it can be applied
to any source of of_get_mac_address.
Rename any mtd-mac-address-increment to mac-address-increment.
Rename any mtd-mac-address-increment-byte to mac-address-increment-byte.
This should make simplify the conversion of target to nvmem implementation.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
AR8031/AR8033 have different status registers for copper
and fiber operation. However, the extended status register
is the same for both operation modes.
As a result of that, ESTATUS_1000_XFULL is set to 1 even when
operating in copper TP mode.
Remove this mode from the supported link modes, as this driver
currently only supports copper operation.
Signed-off-by: David Bauer <mail@david-bauer.net>
Without this patch we have to manually bring up the CPU interface in
failsafe mode.
This was backported from kernel 5.12.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Rafał Miłecki <rafal@milecki.pl>
As patches for the AR8031/AR8033 copper page selection were merged
upstream, we can backport these patches.
This also fixes a PHY capabilities detection issue on the Ubiquiti
ER-X-SFP.
Signed-off-by: David Bauer <mail@david-bauer.net>
The higher 16-bit of EEE register was overwritten by mistake, fix that.
Fixes: 5b9ba4a93e ("generic: mt7530: support adjusting EEE")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Removed upstreamed:
generic/pending-5.4/770-02-net-ethernet-mtk_eth_soc-fix-rx-vlan-offload.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800
Note that since I rebased the previous commit, I removed my Run-tested line
although I confirm building the image successfully.
Signed-off-by: John Audia <graysky@archlinux.us>
Removed upstreamed:
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
bcm63xx/patches-5.4/434-nand-brcmnand-fix-OOB-R-W-with-Hamming-ECC.patch*
Removed/code was included upstream and therefore redundant:
ramips/patches-5.4/999-fix-pci-init-mt7620.patch
All other patches automatically rebased.
* update_kernel.sh did not flag this yet it was included in 5.4.119[1], as a
result of the rebase, I removed my testing lines since I did not go back to
test built or to run test 5.4.119 with the removed patch present.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.4.119&id=e5b3e69eb36ac1178a7a2392616fd29afd288c4e
Signed-off-by: John Audia <graysky@archlinux.us>
This partly reverts commit 20a924d2ae.
This commit broke the build of the Mediatek target with kernel 5.4, for
kernel 5.10 it is fine.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CONFIG_FORTIFY_SOURCE=y is already set in the generic kernel
configuration, but it is not working for MIPS on kernel 5.4, support for
MIPS was only added with kernel 5.5, other architectures like aarch64
support FORTIFY_SOURCE already since some time.
This patch adds support for FORTIFY_SOURCE to MIPS with kernel 5.4,
kernel 5.10 already supports this and needs no changes.
This backports one patch from kernel 5.5 and one fix from 5.8 to make
fortify source also work on our kernel 5.4.
The changes are not compatible with the
306-mips_mem_functions_performance.patch patch which was also removed
with kernel 5.10, probably because of the same problems. I think it is
not needed anyway as the compiler should automatically optimize the
calls to memset(), memcpy() and memmove() even when not explicitly
telling the compiler to use the build in variant.
This increases the size of an uncompressed kernel by less than 1 KB.
Acked-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The new EEE patch is accepted upstream, so backport it and replace the
current one.
Cc: René van Dorst <opensource@vdorst.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
This CFI patch was accepted upstream for 5.13. Move it away from under
ath79 and place under backports to be removed in due time.
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
Manually rebased*
generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch
Added new backport*
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
All others updated automatically.
The new backport was included based on this[1] upstream commit that will be
mainlined soon. This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
*Credit to Alexander Lobakin
1. https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=7ad18ff6449cbd6beb26b53128ddf56d2685aa93
Signed-off-by: John Audia <graysky@archlinux.us>
It's in backports-5.4, but it wasn't ever merged. Upstream followed another
approach, with flow offloading, which has much better performance. Drop this
obsolete patch and refresh the kernel patches.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Felix Fietkau <nbd@nbd.name>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Removed upstreamed:
mvebu/patches-5.4/319-ARM-dts-turris-omnia-configure-LED-2--INTn-pin-as-interrupt-pin.patch
Build system : x86_64
Build-tested : ipq806x/R7800
Run-tested : ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
This fixes incorrect supported link modes indicated when using ethtool
on the Ubiquiti UniFi AC lite / LR / Mesh.
eroot@OpenWrt:~# ethtool eth0
Settings for eth0:
Supported ports: [ TP MII ]
Supported link modes: 100baseT/Half 100baseT/Full
1000baseT/Full
1000baseX/Full
The reason for this is, that since kernel 5.4 the PHY capabilities are
read dynamically from the PHY. As Ubiquiti leaves the PHY in a wrong
state, the capabilities of the SGMII side of the PHY are read.
As a side effect, 10 Mbit/s link modes did not work on these boards.
Signed-off-by: David Bauer <mail@david-bauer.net>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Manually rebased due to movement of rx-offload.c in 5.4.110:
layerscape/patches-5.4/802-can-0002-can-rx-offload-fix-long-lines.patch
layerscape/patches-5.4/802-can-0003-can-rx-offload-can_rx_offload_compare-fix-typo.patch
layerscape/patches-5.4/802-can-0004-can-rx-offload-can_rx_offload_irq_offload_timestamp-.patch
layerscape/patches-5.4/802-can-0005-can-rx-offload-can_rx_offload_reset-remove-no-op-fun.patch
layerscape/patches-5.4/802-can-0006-can-rx-offload-Prepare-for-CAN-FD-support.patch
layerscape/patches-5.4/802-can-0018-can-flexcan-use-struct-canfd_frame-for-CAN-classic-f.patch
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Manually rebased:
pending-5.4/611-netfilter_match_bypass_default_table.patch
The upstream change affecting this patch is the revert of an earlier
kernel commit. Therefore, we just revert our corresponding changes
in [1].
Build system: x86_64
Build-tested: ipq806x/R7800
[1] 9b1b89229f ("kernel: bump 5.4 to 5.4.86")
Signed-off-by: John Audia <graysky@archlinux.us>
[adjust manually rebased patch, add explanation]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Backport upstream patch that fixes TRGMII mode now that mt7530 is
actually resetting the switch on ramips devices.
Patches apply to both Linux 5.4 and 5.10, since TRGMII is broken on both.
Fixes: 69551a2442 ("ramips: manage low reset lines")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
It's meant to provide upstream support for mtd & NVMEM. It's required
e.g. for reading MAC address from mtd partition content. It seems to be
in a final shape so it's worth testing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
5.4.102 backported a lot of stuff that our WireGuard backport already
did, in addition to other patches we had, so those patches were
removed from that part of the series. In the process other patches were
refreshed or reworked to account for upstream changes.
This commit involved `update_kernel.sh -v -u 5.4`.
Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Without this patch, the chacha block counter is not incremented on neon
rounds, resulting in incorrect calculations and corrupt packets.
This also switches to using `--no-numbered --zero-commit` so that future
diffs are smaller.
Reported-by: Hans Geiblinger <cybrnook2002@yahoo.com>
Reviewed-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This adds the latest version of ofpart commit. It hopefully
1. Doesn't break compilation
2. Doesn't break partitioning
(this time).
It's required to implement fixed partitioning with some quirks. It's
required by bcm53xx, bcm4908, kirkwood, lantiq and mvebu.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The CPU_MIPS64 and CPU_MIPS32 variables are supposed to be able to
distinguish broadly between 64-bit and 32-bit MIPS CPUs. However, they
weren't selected by the specialty CPUs, Octeon and Loongson, which meant
it was possible to hit a weird state of:
MIPS=y, CONFIG_64BIT=y, CPU_MIPS64=n
This commit rectifies the issue by having CPU_MIPS64 be selected when
the missing Octeon or Loongson models are selected.
In particular, this affects our octeonplus target.
It has been posted to LKML here:
https://lore.kernel.org/linux-mips/20210227122605.2680138-1-Jason@zx2c4.com/
Cc: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[refresh again]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Allow for single (external-data) FIT image to hold kernel, dtb and
squashfs. In that way, the bootloader verifies the system integrity
including the rootfs, because what's the point of checking that the
hash of the kernel is correct if it won't boot in case of squashfs
being corrupted? Better allow bootloader to check everything needed
to make it at least up to failsafe mode. As a positive side effect
this change also makes the sysupgrade process on nand potentially
much easier as it is now.
In short: mkimage has a parameter '-E' which allows generating FIT
images with 'external' data rather than embedding the data into the
device-tree blob itself. In this way, the FIT structure itself remains
small and can be parsed easily (rather than having to page around
megabytes of image content). This patch makes use of that and adds
support for adding sub-images of type 'filesystem' which are used to
store the squashfs. Now U-Boot can verify the whole OS and the new
partition parsers added in the Linux kernel can detect the filesystem
sub-images, create partitions for them, and select the active rootfs
volume based on the configuration in FIT (passing configuration via
device tree could be implemented easily at a later stage).
This new FIT partition parser works for NOR flash (on top of mtdblock),
NAND flash (on top of ubiblock) as well as classic block devices
(ie. eMMC, SDcard, SATA, NVME, ...).
It could even be used to mount such FIT images via `losetup -P` on a
user PC if this patch gets included in Linux upstream one day ;)
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Marvell mv88e6xxx switch series cannot perform MAC learning from
CPU-injected (FROM_CPU) DSA frames, which results in 2 issues.
- excessive flooding, due to the fact that DSA treats those addresses
as unknown
- the risk of stale routes, which can lead to temporary packet loss
Backport those patch series from netdev mailing list, which solve these
issues by adding and clearing static entries to the switch's FDB.
Add a hack patch to set default VID to 1 in port_fdb_{add,del}. Otherwise
the static entries will be added to the switch's private FDB if VLAN
filtering disabled, which will not work.
The switch may generate an "ATU violation" warning when a client moves
from the CPU port to a switch port because the static ATU entry added by
DSA core still points to the CPU port. DSA core will then clear the static
entry so it is not fatal. Disable the warning so it will not confuse users.
Link: https://lore.kernel.org/netdev/20210106095136.224739-1-olteanv@gmail.com/
Link: https://lore.kernel.org/netdev/20210116012515.3152-1-tobias@waldekranz.com/
Ref: https://gitlab.nic.cz/turris/turris-build/-/issues/165
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
This patch allows devices without a high resolution timer to boot up faster.
It should speed up boots for bcm2708 and bcm63xx.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
No manual changes needed.
Build system: x86_64
Build-tested: bcm27xx/bcm2711
Signed-off-by: John Audia <graysky@archlinux.us>
File extension was truncated for
pending-5.4/770-11-net-ethernet-mtk_eth_soc-avoid-rearming-interrupt-if.pa
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds quirks support to the "ofpart" parser. It's required to
support fixed partitions that require some extra logic.
Right now only BCM4908 binding is supported (BCM4908 requires detecting
currently used "firmware" partition).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The intention is for the loop to timeout if the body does not succeed.
The current logic calls time_is_before_jiffies(timeout) which is false
until after the timeout, so the loop body never executes.
time_is_after_jiffies(timeout) will return true until timeout is less
than jiffies, which is the intended behavior here.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.
Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86/64]