CPU: Atheros AR9342 rev 3 SoC
RAM: 64 MB DDR2
Flash: 16 MB NOR SPI
WLAN 2.4GHz: Atheros AR9342 v3 (ath9k)
WLAN 5.0GHz: QCA988X
Ports: 1x GbE
Flashing procedure is identical to other ubnt devices.
https://openwrt.org/toh/ubiquiti/common
Flashing through factory firmware
1. Ensure firmware version v8.7.0 is installed.
Up/downgrade to this exact version.
2. Patch fwupdate.real binary using
`hexdump -Cv /bin/ubntbox | sed 's/14 40 fe 27/00 00 00 00/g' | \
hexdump -R > /tmp/fwupdate.real`
3. Make the patched fwupdate.real binary executable using
`chmod +x /tmp/fwupdate.real`
4. Copy the squashfs factory image to /tmp on the device
5. Flash OpenWrt using `/tmp/fwupdate.real -m <squashfs-factory image>`
6. Wait for the device to reboot
(copied from Ubiquiti NanoBeam AC and modified)
Flashing from serial console
1. Connect serial console (115200 baud)
2. Connect ethernet to a network with a TFTP server, through a
passive PoE injector.
3. Press a key to obtain a u-boot prompt
4. Set your TFTP server's ip address, with:
setenv serverip <tftp-server-address>
5. Set the Bullet AC's ip address, with:
setenv ipaddr <bullet-ac-address>
6. Set the boot file, with:
setenv bootfile <name-of-initramfs-binary-on-tftp-server>
7. Fetch the binary with tftp:
tftpboot
8. Boot the initramfs binary:
bootm
9. From the initramfs, fetch the sysupgrade binary, and flash it with
sysupgrade.
The Bullet AC is identified as a 2WA board by Ubiquiti. As such, the UBNT_TYPE
must match from the "Flashing through factory firmware" install instructions
to work.
Phy0 is QCA988X which can tune either band (2.4 or 5GHz). Phy1 is AR9342,
on which 5GHz is disabled. It isn't currently known whether phy1 is
routed to the N connector at all.
Signed-off-by: Russell Senior <russell@personaltelco.net>
The following four led triggers are enabled in generic config.
* kmod-ledtrig-default-on
* kmod-ledtrig-heartbeat
* kmod-ledtrig-netdev
* kmod-ledtrig-timer
Drop the packages and remove them from DEVICE_PACKAGES.
There's no other package depending on them in this repo.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Those targets have already enabled some other LED triggers, so enabling
a few more won't be a big problem.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The heartbeat trigger is used by luci-mod-system, which is installed
as a part of the standard luci package set. It seems the LED trigger
will be required quite often, so let's enable it by default.
This increases uncompressed kernel size by about 100 bytes on ath79/generic.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
With encryption disabled, it was intended to set wpa_state=1 (enabled,
not configured) through the 'wps_not_configured' flag.
The flag is set appropriately but the condition using it is broken.
Instead, 'wps_configured' is checked and wpa_state is always 2 (enabled,
configured). Fix it by using the correct variable name.
Fixes: 498d84fc4e ("netifd: add wireless configuration support
and port mac80211 to the new framework")
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit title/message improvements]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
CONFIG_THERMAL option was changed to boolean in upstream linux commit
554b3529fe01 ("thermal/drivers/core: Remove the module Kconfig's option").
Switch it to 'y' and remove FILES and AUTOLOAD for non-existant module file.
And update the descripton text for the package as in upstream linux commit
eb8504620381 ("thermal: Rephrase the Kconfig text for thermal").
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The cidr_parse6 function parses a string to an ipv6-address.
The cidr struct contains a union called buf for the ipv4 and ipv6
address. Since it is a char pointer and the struct is initialized with
the maximum size (so ipv6 string) it does not make any difference.
However, we should access the buffer using the v6 name, since it could
be confusing otherwise.
Signed-off-by: Nick Hainke <vincent@systemli.org>
This fixes a typo in the previously committed partition map that led to
the extension of the read-only mtd partition "SSD" into the following
partitions.
Fixes: 4e46beb313 ("ipq806x: add support for Ubiquiti UniFi AC HD")
Signed-off-by: Jan Alexander <jan@nalx.net>
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.
Build system: x86_64
Build-tested: ipq806x/R7800, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86/64]
Since 4ee3cf2b5a profiles with alternative vendor names may appear
multiple times in `tmp/.targetinfo` or `.targetinfo` (for
ImageBuilders).
The `target-metadata.pl` script adds these profiles then twice to
`PROFILE_NAMES` and the ImageBuilder show the profile twice when running
`make info`.
This patch removes duplicate profile IDs and only adds them once to
`.profiles.mk`.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Not everyone will want to bloat their kernel by 24 kiB for such a niche
feature.
Fixes: a1a7f3274e "kernel: enable SRv6 support by
enabling lwtunnel"
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
BCM4908 CFE bootloader requires kernel to be prepended with a custom
header. This simple tool implements support for such headers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
glibc does not officially support ARC700 so this adds the missing
pieces. I looked at uClibc-ng and a patch by Synopsis for glibc.
ran make toolchain/glibc/refresh to clean up fuzz.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
a46f9a9160e9 mt76: mt7915: add vif check in mt7915_update_vif_beacon()
27ad12352ac9 mt76: mt7615: add vif check in mt7615_update_vif_beacon()
0a449cef024e mt76: mt7915: fix MT_CIPHER_BIP_CMAC_128 setkey
eacd2d493c61 mt76: mt7915: reset token when mac_reset happens
e4b23301e6c9 mt76: mt7615: reset token when mac_reset happens
6e22bbfe0360 mt76: mt7615: convert comma to semicolon
37865118ae2d mt76: mt7915: convert comma to semicolon
742c36b2e527 mt76: mt7915: run mt7915_configure_filter holding mt76 mutex
a515727e8423 mt76: mt7915: add support for flash mode
b6f7b3da5216 mt76: mt7915: fix endianness warning in mt7915_mcu_set_radar_th
062f3f4f06a2 mt76: mt7915: simplify mt7915_mcu_send_message routine
dbba9b993300 mt76: mt7915: drop zero-length packet to avoid Tx hang
36a745d0f71c mt76: Fix queue ID variable types after mcu queue split
a4539760b0b1 mt7915: update the testmode support to the latest upstream patch
64bd6f87e4c2 mt7915: fix crash on failure in pci_set_dma_mask
c202ace409e0 mt76: remove unused variable q
d1b827781f84 mt76: mt7915: add partial add_bss_info command on testmode init
a897a69769f5 mt76: testmode: introduce dbdc support
b44472e99822 mt76: testmode: move mtd part to mt76_dev
45e27e6cdc12 mt76: mt7915: move testmode data from dev to phy
b6673b005770 mt76: mt7615: move testmode data from dev to phy
abdd471e9f2d mt76: mt7915: fix ht mcs in mt7915_mcu_get_rx_rate()
d679b56b9585 mt76: move mac_work in mt76_core module
36cd48ab4454 mt76: move chainmask in mt76_phy
89a6781ed045 mt76: mt7915: force ldpc for bw larger than 20MHz in testmode
3d0834e78005 mt76: testmode: add support to set user-defined spe index
cc05f4679667 mt76: testmode: add attributes for ipg related parameters
77b18b16fe16 mt76: testmode: make tx queued limit adjustable
6365a58573cb mt76: mt7915: split edca update function
e56282bf67f6 mt76: mt7915: add support for ipg in testmode
6fa642903e4e mt76: mt7915: calculate new packet length when tx_time is set in testmode
729ec5daeba5 mt76: mt7915: clean hw queue before starting new testmode tx
981443da5cf7 mt76: testmode: add a new state for continuous tx
4793fc9b3d48 mt76: mt7915: rework set state part in testmode
11a1e86e5946 mt76: mt7915: add support for continuous tx in testmode
364affef82fc mt76: mt7615: mt7915: disable txpower sku when testmode enabled
9fc19db51293 mt76: mt7915: simplify peer's TxBF capability check
6377b7f330be mt76: mt7915: add implicit Tx beamforming support
983091a40633 mt76: mt7915: fix MESH ifdef block
bbb7a9e77751 mt76: mt76u: fix NULL pointer dereference in mt76u_status_worker
a28a8dd2f7de mt76: usb: fix crash on device removal
9c312f2ce2c5 mt76: mt7915: rework mcu API
e6fe82acb111 mt76: mt7915: disable RED support in the WA firmware
25d7429bdc41 mt76: mt7915: fix eeprom parsing for DBDC
7a93026dd3dc mt76: mt7915: fix eeprom DBDC band selection
4c8a09cc45d0 tools: Set mode for new file /tmp/mt76-test-%s
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The key_mgmt variable was mistyped when checking against "WPS", so
the if clause was never entered.
Fixes: f5753aae23 ("hostapd: add support for WPS pushbutton station")
Signed-off-by: Leon M. George <leon@georgemail.eu>
[add commit message, bump PKG_RELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
'base' was never used.
Fixes: 498d84fc4e ("netifd: add wireless configuration support
and port mac80211 to the new framework")
Signed-off-by: Leon M. George <leon@georgemail.eu>
'enc_str' was never used.
Fixes: 498d84fc4e ("netifd: add wireless configuration support
and port mac80211 to the new framework")
Signed-off-by: Leon M. George <leon@georgemail.eu>
Granting capabilities CAP_NET_ADMIN and CAP_NET_RAW allows running
hostapd and wpa_supplicant without root priviledges.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This allows configuration of multicast_to_unicast and per_sta_vif options.
- multicast_to_unicast requests multicast-to-unicast conversion.
- per_sta_vif assigns each station its own AP_VLAN interface.
Signed-off-by: Etan Kissling <etan_kissling@apple.com>
This adds a config option to allow compiling with HKDF algorithm support
to support applications that require this feature.
Signed-off-by: Etan Kissling <etan_kissling@apple.com>
This allows libnetfilter_queue to access connection tracking information
by requesting NFQA_CFG_F_CONNTRACK. Connection tracking information is
provided in the NFQA_CT attribute.
CONFIG_NETFILTER_NETLINK_GLUE_CT enables the interaction between
nf_queue and nf_conntrack_netlink. Without this option, trying to access
connection tracking information results in "Operation not supported".
Signed-off-by: Etan Kissling <etan_kissling@apple.com>
The current master only supports kernel 5.4, and there is no reason
to remove KERNEL_IO_URING for future kernels.
Drop the unneeded dependency.
Signed-off-by: Andy Walsh <andy.walsh44+github@gmail.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
It looks like GitHub changed the URL path for release tarballs, thus the
download for the zstd package was always falling back to the OpenWrt
sources mirror.
Fix the GitHub URL for one which works. The file hash remains unchanged.
Signed-off-by: David Bauer <mail@david-bauer.net>
Both devices use u-boot env variables to boot OpenWrt from its flash
partition. Using u-boot envtools, it is possible to change the bootcmd
back to the stock firmware partition directly from OpenWrt without
attaching a serial cable or even physically accessing the device.
Signed-off-by: Jan Alexander <jan@nalx.net>
Hardware
--------
SoC: Qualcomm IPQ8064
RAM: 512MB DDR3
Flash: 256MB NAND (Micron MT29F2G08ABBEAH4)
32MB SPI-NOR (Macronix MX25U25635F)
WLAN: Qualcomm Atheros QCA9994 4T4R b/g/n
Qualcomm Atheros QCA9994 4T4R a/n/ac
ETH: eth0 - SECONDARY (Atheros AR8033)
eth1 - MAIN (Atheros AR8033)
USB: USB-C
LED: Dome (white / blue)
BTN: Reset
Installation
------------
Copy the OpenWrt sysupgrade image to the /tmp directory of the device
using scp. Default IP address is 192.168.1.20 and default username and
password are "ubnt".
SSH to the device and write the bootselect flag to ensure it is booting
from the mtd partition the OpenWrt image will be written to. Verify the
output device below matches mtd partition "bootselect" using /proc/mtd.
> dd if=/dev/zero bs=1 count=1 seek=7 conv=notrunc of=/dev/mtd11
Write the OpenWrt sysupgrade image to the mtd partition labeled
"kernel0". Also verify the used partition device using /proc/mtd.
> dd if=/tmp/sysupgrade.bin of=/dev/mtdblock12
Reboot the device.
Back to stock
-------------
Use the TFTP recovery procedure with the Ubiquiti firmware image to
restore the vendor firmware.
Signed-off-by: Jan Alexander <jan@nalx.net>
Update the U-Boot to version v2021.01.
Run-tested: FriendlyARM NanoPi R2S
Radxa Rock Pi 4
Pine64 RockPro64
Signed-off-by: Marty Jones <mj8263788@gmail.com>
[format commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
Currently PHY information obtained from "iw phy" lacks information about
a PHYs HE capabilities when using the by default installed iw-tiny.
As there are already 802.11ax supported devices, enabled printing this
information for the by-default installed iw variant.
Signed-off-by: David Bauer <mail@david-bauer.net>
BCM4906, BCM4908 and BCM49408 are SoCs with 64 bit ARMv8 B53 CPUs.
Upstream Linux is slowly getting support for that SoCs family so it
makes sense to add target for it.
This prepares initial support for:
1. Asus GT-AC5300
BCM4908 based device (4 CPUs) with 1024 MiB RAM, NAND, 8 LAN ports.
2. Netgear R8000P
BCM4906 based device (2 CPUs) with 512 MiB RAM, NAND, 4 LAN ports.
Flashing info will come later as we learn how to generate proper images.
It isn't usable yet (it only produces a bootable kernel) so "source-only"
is used.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Enable the ability to use segment routing based on IPv6. It allows the
packet to specify a path that the packet should take through the
network.
Lwtunnel allow an easy encapsulation of a package. You can just install
ip-full package and use it:
ip -6 route add 2003::/64 dev eth0 encap seg6 mode encap \
segs 2001::1,2002::2
An IPv6 package looks like this:
[IPv6 HDR][IPv6 RH][IPv6 HDR][Data...]
Netifd support:
https://git.openwrt.org/?p=project/netifd.git;
a=commit;h=458b1a7e9473c150a40cae5d8be174f4bb03bd39
Increases imagesize by 24.125 KiB. Therefore, only enable for devices
with enough flash.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Previously, ccache would end up using the system libzstd, which is not
supposed to be a build requirement.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
When compiling with CONFIG_ALL_KMODS enabled, compilation might stall
due to unset rockchip-specific config symbols. Disable these to avoid
stalling this step.
Signed-off-by: David Bauer <mail@david-bauer.net>
Instead of using an ancient qemu version in-tree the building machine
should just have qemu-utils installed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Currently `qemu-img` is used to convert raw x86 images to VDI and VMDK
images, used for virtual machines.
Having `qemu-img` in tree requires us to maintain an ancient version of
`qemu-utils`, which recently required extra work to compile with newer
compiler version.
This commit prints a warning message in case `qemu-img` is missing.
As a next step the in-tree version of `qemu-img` can be removed.
Signed-off-by: Paul Spooren <mail@aparcar.org>
To simplify the way netifd acquires the PIDs of wpa_supplicant and
hostapd let the config_add method of both of them return the PID of the
called process. Use the returned PID instead of querying procd when
adding wpa_supplicant configuration.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Linux 5.9 introduces support for ZSTD ramdisk and initrd compression,
make sure we enable/disable the relevant options when building an
initramfs enabled kernel.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
