Commit Graph

144 Commits

Author SHA1 Message Date
Christian Lamparter
84f13e19b4 ipq40xx: essedma: Add fix for memory allocation issues
This patch adds a ChromiumOS 3.18 patch [0] that fixes memory
allocation issues under memory pressure by keeping track
of missed allocs and rectify the omission at a later date.
It also adds ethtool counters for memory allocation
failures accounting so this can be verified.

[0] <d4e1e4ce68>

Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-24 21:17:41 +01:00
Steve Glennon
dc4f6b896f ipq40xx: add support for EnGenius ENS620EXT
Hardware
--------
CPU:   Qualcomm IPQ4018
RAM:   256M
FLASH: 32M SPI NOR W25Q256
ETH:   QCA8075
WiFi2: IPQ4018 2T2R 2SS b/g/n
WiFi5: IPQ4018 2T2R 2SS n/ac
LED:    - Power amber
        - LAN1(PoE) green
        - LAN2 green
        - Wi-Fi 2.4GHz green
        - Wi-Fi 5GHz green
BTN:    - WPS
UART:  115200n8 3.3V J1
       VCC(1) - GND(2) - TX(3) - RX(4)

Added basic support to get the device up and running for a sysupgrade
image only.
There is currently no way back to factory firmware, so this is a one-way
street to OpenWRT.
Install from factory condition is convoluted, and may brick your device:
1) Enable SSH and disable the CLI on the factory device from the web user
   interface (Management->Advanced)
2) Reboot the device
3) Override the default, limited SSH shell:
   a) Get into the ssh shell:
      ssh admin@192.168.1.1 /bin/sh --login
   b) Change the dropbear script to disable the limited shell. At the
      empty command prompt type:
        sed -i '/login_ssh/s/^/#/g’ dropbear
        /etc/init.d/dropbear restart
        exit
4) ssh in to a (now-) normal OpenWRT SSH session
5) Flash your built image
   a) scp openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin
      admin@192.168.1.1:/tmp/
   b) ssh admin@192.168.1.1
   c) sysupgrade -n
      /tmp/openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin
6) After flash completes (it may say "Upgrade failed" followed by
   "Upgrade completed") and device reboots, log in to newly flashed
   system. Note you will now need to ssh as root rather than admin.

Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
[whitespace fixes, reordered partitions, removed rng node from 4.14,
fixed 901-arm-boot-add-dts-files.patch]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-21 00:57:54 +01:00
Marius Genheimer
41a86debe3 ipq40xx: limit frequencies for Asus Lyra
The Asus Lyra has filters in the antenna paths which limits
the usable frequencies on both 5GHz radios.

Signed-off-by: Marius Genheimer <mail@f0wl.cc>
2019-03-13 16:25:35 +01:00
David Bauer
148d29d47b ipq40xx: add support for AVM FRITZ!Repeater 3000
Hardware
--------
CPU:   Qualcomm IPQ4019
RAM:   256M (NANYA NT5CC128M16JR-EK)
FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI)
ETH:   Qualcomm QCA8072
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
WiFi5: QCA9984 4T4R 4SS n/ac
LED:    - Connect green/blue/red
        - Power green
BTN:   WPS/Connect
UART:  115200n8 3.3V
       VCC - RX - TX - GND (Square is VCC)

Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz3000'
   subdirectory. Place it in the same directory as the 'eva_ramboot.py'
   script. It is located in the 'scripts/flashing' subdirectory of the
   OpenWRT tree.

2. Assign yourself the IP address 192.168.178.10/24. Connect your
   Computer to one of the boxes LAN ports.

3. Connect Power to the Box. As soon as the LAN port of your computer
   shows link, load the U-Boot to the box using following command.

   > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin

4. The U-Boot will now start. Now assign yourself the IP address
   192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
   server root directory and rename it to 'FRITZ3000.bin'.

5. The Box will now boot OpenWRT from RAM. This can take up to two
   minutes.

6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
   scp. SSH into the Box and first write the Bootloader to both previous
   kernel partitions.

   > mtd write /path/to/uboot-fritz3000.bin uboot0
   > mtd write /path/to/uboot-fritz3000.bin uboot1

7. Remove the AVM filesystem partitions to make room for our kernel +
   rootfs + overlayfs.

   > ubirmvol /dev/ubi0 --name=avm_filesys_0
   > ubirmvol /dev/ubi0 --name=avm_filesys_1

8. Flash OpenWRT peristently using sysupgrade.

   > sysupgrade -n /path/to/openwrt-sysupgrade.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-03-13 16:25:35 +01:00
David Bauer
5389db72e3 fritz-tools: add support for IPQ40xx platform
AVM devices based on Qualcomm IPQ40xx do not store sector health
information in the OOB area. Make this check optional to support this
platform.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-03-13 16:25:34 +01:00
David Bauer
93601d647f ipq40xx: fix FRITZBox 7530 NAND controller node
This removes the 'cs-gpios' property from the AVM FRITZ!Box 7530 NAND
controller node. As pointed out by Christian Lamparter, the property is
not needed by the Qualcomm NAND controller driver.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-03-13 16:25:34 +01:00
Christian Lamparter
784f2e73df ipq40xx: fix phy interrupt setting
This patch fixes a problem that was discovered during DSA
development. On the MR33, the link change events from the
external AR8035-PHY would never make it to the qca8k driver.

The issue turned out to be a misplaced memcpy that was copying
over the zero-initialized irq table, when it should have been
set to PHY_POLL. Hence this patch moves the memcpy after the
array has been initialized.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-13 16:25:34 +01:00
Christian Lamparter
39092ad9e9 ipq40xx: tidy up 02_networks
- fix linksys' EA6350v3 order

 - remove whitespace that should have been tabs

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-03-13 16:25:34 +01:00
Piotr Dymacz
24de7c29e5 ipq40xx: backport I2C QUP driver changes from 4.17
Backport below changes for I2C QUP driver from v4.17:

  0668bc44a426 i2c: qup: fix copyrights and update to SPDX identifier
  7239872fb340 i2c: qup: fixed releasing dma without flush operation completion
  eb422b539c1f i2c: qup: minor code reorganization for use_dma
  6d5f37f166bb i2c: qup: remove redundant variables for BAM SG count
  c5adc0fa63a9 i2c: qup: schedule EOT and FLUSH tags at the end of transfer
  7e6c35fe602d i2c: qup: fix the transfer length for BAM RX EOT FLUSH tags
  3f450d3eea14 i2c: qup: proper error handling for i2c error in BAM mode
  08f15963bc75 i2c: qup: use the complete transfer length to choose DMA mode
  ecb6e1e5f435 i2c: qup: change completion timeout according to transfer length
  6f2f0f6465ac i2c: qup: fix buffer overflow for multiple msg of maximum xfer len
  f7714b4e451b i2c: qup: send NACK for last read sub transfers
  fbfab1ab0658 i2c: qup: reorganization of driver code to remove polling for qup v1
  7545c7dba169 i2c: qup: reorganization of driver code to remove polling for qup v2

This fixes various I2C issues observed on AP120C-AC board equipped with
Atmel/Microchip AT97SC3205T TPM module.

Tested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-08 19:28:31 +01:00
Piotr Dymacz
ff8a8074b2 ipq40xx: add ath10k-calibration-variant in AP120C-AC DTS
Use 'ath10k-calibration-variant' (with the value sent upstream) for the
second (5 GHz) radio in AP120C-AC board DTS. First radio uses the same
BDF as in one of Qualcomm reference designs.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-03-08 19:28:31 +01:00
Koen Vandeputte
1cfbf95393 kernel: bump 4.14 to 4.14.104
Refreshed all patches.

Altered patches:
- 332-arc-add-OWRTDTB-section.patch

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-03-05 13:19:43 +01:00
David Bauer
95b0c07a61 ipq40xx: add support for FritzBox 7530
Hardware
--------
CPU:   Qualcomm IPQ4019
RAM:   256M
FLASH: 128M NAND
ETH:   QCA8075
VDSL:  Intel/Lantiq VRX518 PCIe attached
       currently not supported
DECT:  Dialog SC14448
       currently not supported
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
LED:    - Power/DSL green
        - WLAN green
        - FON/DECT green
        - Connect/WPS green
        - Info green
        - Info red
BTN:    - WLAN
        - FON
        - WPS/Connect
UART:  115200n8 3.3V (located under the Dialog chip)
       VCC - RX - TX - GND (Square is VCC)

Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz7530'
   subdirectory. Place it in the same directory as the 'eva_ramboot.py'
   script. It is located in the 'scripts/flashing' subdirectory of the
   OpenWRT tree.

2. Assign yourself the IP address 192.168.178.10/24. Connect your
   Computer to one of the boxes LAN ports.

3. Connect Power to the Box. As soon as the LAN port of your computer
   shows link, load the U-Boot to the box using following command.

   > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin

4. The U-Boot will now start. Now assign yourself the IP address
   192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
   server root directory and rename it to 'FRITZ7530.bin'.

5. The Box will now boot OpenWRT from RAM. This can take up to two
   minutes.

6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
   scp. SSH into the Box and first write the Bootloader to both previous
   kernel partitions.

   > mtd write /path/to/uboot-fritz7530.bin uboot0
   > mtd write /path/to/uboot-fritz7530.bin uboot1

7. Remove the AVM filesystem partitions to make room for our kernel +
   rootfs + overlayfs.

   > ubirmvol /dev/ubi0 --name=avm_filesys_0
   > ubirmvol /dev/ubi0 --name=avm_filesys_1

8. Flash OpenWRT peristently using sysupgrade.

   > sysupgrade -n /path/to/openwrt-sysupgrade.bin

Signed-off-by: David Bauer <mail@david-bauer.net>
[removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:32:55 +01:00
Christian Lamparter
18e942b6c4 ipq40xx: fix pcie msi IRQ trigger level
From: Niklas Cassel <niklas.cassel@linaro.org>
|The databook clearly states that the MSI IRQ (msi_ctrl_int) is a level
|triggered interrupt.
|
|The msi_ctrl_int will be high for as long as any MSI status bit is set,
|thus the IRQ type should be set to IRQ_TYPE_LEVEL_HIGH, causing the
|IRQ handler to keep getting called, as long as any MSI status bit is set.
|[...]
|Not having the correct IRQ type defined will cause us to lose interrupts,
|which in turn causes timeouts in the PCIe endpoint drivers.
|
|Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
|Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:26:11 +01:00
Christian Lamparter
46b949a067 ipq40xx: enlarge PCIe BAR size
David Bauer reported that the VDSL modem (attached via PCIe)
on his AVM Fritz!Box 7530 was complaining about not having
enough space in the BAR. A closer inspection of the old
qcom-ipq40xx.dtsi pulled from the GL-iNet repository listed:

| qcom,pcie@80000 {
|       compatible = "qcom,msm_pcie";
|       reg = <0x80000 0x2000>,
|             <0x99000 0x800>,
|             <0x40000000 0xf1d>,
|             <0x40000f20 0xa8>,
|             <0x40100000 0x1000>,
|             <0x40200000 0x100000>,
|             <0x40300000 0xd00000>;
|       reg-names = "parf", "phy", "dm_core", "elbi",
|                       "conf", "io", "bars";

Matching the reg-names with the listed reg leads to
<0xd00000> as the size for the "bars".

BugLink: https://www.mail-archive.com/openwrt-devel@lists.openwrt.org/msg45212.html
Reported-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:26:11 +01:00
张鹏
bbab33724d ipq40xx: add support for Qxwlan E2600AC C1 and C2
Qxwlan E2600AC C1 based on IPQ4019

Specifications:
SOC:	Qualcomm IPQ4019
DRAM:	256 MiB
FLASH:	32 MiB Winbond W25Q256
ETH:	Qualcomm QCA8075
WLAN:	5G + 5G/2.4G
	* 2T2R 2.4/5 GHz
	 - QCA4019 hw1.0 (SoC)
	* 2T2R 5 GHz
	 - QCA4019 hw1.0 (SoC)
INPUT:  Reset buutton
LED:	1x Power ,6 driven by gpio
SERIAL: UART (J5)
UUSB:	USB3.0
POWER:	1x DC jack for main power input (9-24 V)
SLOT:	Pcie (J25), sim card (J11), SD card (J51)

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "sysupgrade" image
   and click the upgrade button.

Qxwlan E2600AC C2 based on IPQ4019

Specifications:
SOC:	Qualcomm IPQ4019
DRAM:	256 MiB
NOR:	16 MiB Winbond W25Q128
NAND:	128MiB Micron MT29F1G08ABAEAWP
ETH:	Qualcomm QCA8075
WLAN:	5G + 5G/2.4G
	* 2T2R 2.4/5 GHz
	 - QCA4019 hw1.0 (SoC)
	* 2T2R 5 GHz
	 - QCA4019 hw1.0 (SoC)
INPUT:  Reset buutton
LED:	1x Power, 6 driven by gpio
SERIAL: UART (J5)
USB:	USB3.0
POWER:	1x DC jack for main power input (9-24 V)
SLOT:	Pcie (J25), sim card (J11), SD card (J51)

Flash instruction (using U-Boot CLI and tftp server):

 - Configure PC with static IP 192.168.1.10 and tftp server.
 - Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp
   server directory.
 - Connect PC with one of RJ45 ports, power up the board and press
   "enter" key to access U-Boot CLI.
 - Use the following command to update the device to OpenWrt: "run lfw".

Flash instruction (using U-Boot web-based recovery):

 - Configure PC with static IP 192.168.1.xxx(2-254)/24.
 - Connect PC with one of RJ45 ports, press the reset button, power up
   the board and keep button pressed for around 6-7 seconds, until LEDs
   start flashing.
 - Open your browser and enter 192.168.1.1, select "ubi" image
   and click the upgrade button.

Signed-off-by: 张鹏 <sd20@qxwlan.com>
[ added rng node. whitespace fixes, ported 02_network,
ipq-wifi Makefile, misc dts fixes, trivial message changes ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-28 11:26:11 +01:00
Piotr Dymacz
c568c6dc09 ipq40xx: add support for ALFA Network AP120C-AC
ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm
IPQ4018 + QCA8075 platform.

Specification:

- Qualcomm IPQ4018 (717 MHz)
- 256 MB of RAM (DDR3)
- 16 MB (SPI NOR) + 128 MB (SPI NAND) of flash
- 2x Gbps Ethernet, with 802.3af PoE support in one port
- 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922)
- 3x U.FL connectors
- 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas
- Atmel/Microchip AT97SC3205T TPM module (I2C bus)
- TI CC2540 Bluetooth LE module (USB 2.0 bus)
- 4x LED (all driven by GPIO)
- 1x button (reset)
- 1x USB 2.0 (optional, not installed in indoor version)
- DC jack for main power input (12 V)
- UART header available on PCB (2.0 mm pitch)

Flash instruction:

1. This board uses dual-image feature (128 MB NAND is divided into two
   64 MB partitions: 'rootfs1' and 'rootfs2').
2. Before update, make sure your device is running firmware no older
   than v1.1 (previous versions have incompatible U-Boot).
3. Use 'factory' image in vendor GUI or for sysupgrade tool, without
   preserving settings.

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-02-26 00:16:22 +01:00
Piotr Dymacz
99f72c0d62 ipq40xx: add support for Macronix MX35LF1GE4AB SPI NAND
Without a proper SPI NAND support (SPI NAND framework is available in
kernel >= 4.19) the only way to make such flash working is to include
it in raw/parallel NAND subsystem support and combine with mt29f staging
driver. Obviously, this approach isn't going to be accepted by upstream
(similar support for Winbond W25N01GV was rejected).

Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
2019-02-26 00:15:38 +01:00
Koen Vandeputte
3a2668c6d5 kernel: bump 4.14 to 4.14.102
Refreshed all patches.

Remove upstreamed:
- 272-uapi-if_ether.h-prevent-redefinition-of-struct-ethhd.patch

Remove upstreamed hunks:
- 080-pinctrl-msm-fix-gpio-hog-related-boot-issues.patch

Fixes:
- CVE-2018-1000026

Compile-tested on: ar71xx, cns3xxx, imx6, x86_64
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-02-22 10:53:42 +01:00
Christian Lamparter
a69e101ed1 ipq40xx: speed up ath10k-caldata extraction
Reading and writing to and from flash storage is slow and currently,
the ath10kcal_extract() scripts are even more at an disadvantage
because they use a block size of 1 to be able skip.

This patch reworks the extraction scripts to be much faster and
efficient by reading and writing the calibration data in possibly
one big block.

before: (Tested on a RT-AC58U, which has SPI-NAND).

 # time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=1 skip=4096 count=12064
12064+0 records in
12064+0 records out
real    0m 0.28s
user    0m 0.02s
sys     0m 0.24s

after:

 # time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=12064 skip=4096 count=1 iflag=skip_bytes
1+0 records in
1+0 records out
real    0m 0.01s
user    0m 0.00s
sys     0m 0.00s

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-20 18:51:19 +01:00
Oever González
c35d7f3f8a ipq40xx: fix ipq40xx_setup_macs for Linksys EA6350v3
This commit fixes the script that sets the MAC address of the LAN
switch. The LAN MAC address should be the WAN MAC address plus one.

Without this patch the WAN and the LAN interface will use the same
MAC address and an error will be generated.

With this patch all interfaces will have a different MAC address,
consecutive in the following order: WAN, LAN, radio0 and radio1.

Signed-off-by: Oever González <notengobattery@gmail.com>
2019-02-14 16:56:15 +01:00
Marius Genheimer
9ad3967f14 ipq40xx: add support for ASUS Lyra
SoC:   Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores
RAM:   256 MiB (Nanya NT5CC128M16IP-DI)
FLASH: 128 MiB (Macronix NAND)
WiFi0: Qualcomm IPQ4019 b/g/n 2x2
WiFi1: Qualcomm IPQ4019 a/n/ac 2x2
WiFi2: Qualcomm Atheros QCA9886 a/n/ac
BT:    Atheros AR3012
IN:    WPS Button, Reset Button
OUT:   RGB-LED via TI LP5523 9-channel Controller
UART:  Front of Device - 115200 N-8
       Pinout 3.3v - RX - TX - GND (Square is VCC)

Installation:
1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp.
Login credentials are identical to the Web UI.

2. Login to the device via SSH.

3. Flash the initramfs image using

> mtd-write -d linux -i openwrt-image-file

4. Power-cycle the device and wait for OpenWRT to boot.

5. From there flash the OpenWRT-sysupgrade image.

Ethernet-Ports: Although labeled identically, the port next to
the power socket is the LAN port and the other one is WAN. This
is the same behavior as in the stock firmware.

Signed-off-by: Marius Genheimer <mail@f0wl.cc>
[Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh,
reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79,
minor dts touchup, added rng to 4.19 dts]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-14 16:56:15 +01:00
Christian Lamparter
5ee9763aaa ipq40xx: ea6350v3: 4.19: enable pseudo rng support
Robert Marko made a big effort to enable the rng on all
ipq40xx for 4.19, so let's continue the quest.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-14 16:56:15 +01:00
Christian Lamparter
d753a3ef0e ipq40xx: fix ASUS RT-AC58U switch port numbering
This patch fixes the ASUS' RT-AC58U port order by
unifying the configuration with the NBG6617.

Reported-by: Roberto Socrates (rtac58u-user on the forum)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-05 16:28:12 +01:00
Christian Lamparter
775258c128 ipq40xx: consolidate 02_network board defaults
This patch splits the big board case switch in 02_network in
two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs()
just like ath79 and ramips do.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-02-05 16:28:12 +01:00
Oever González
a873b29284 ipq40xx: add support for Linksys EA6350v3
Specifications:
SOC: Qualcomm IPQ4018
RAM: 256 MiB Samsung K4B2G1646F-BYK0
FLASH1: MX25L1605D 2 MB
FLASH2: Winbond W25N01GV 128Mb
ETH: Qualcomm QCA8075
WLAN0: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN1: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: WPS, Reset
LED: Status - Green
SERIAL: Header at J19, Beneath DC Power Jack
        1-VCC ; 2-TX ; 3-RX; 4-GND;
        Serial 115200-8-N-1.

Tested and working:
- USB (requires extra packages)
- LAN Ethernet (Correct MAC-address)
- WAN Ethernet (Correct MAC-address)
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from Web UI
- OpenWRT sysupgrade
- LED
- Reset Button

Need Testing:
- WPS button

Install via Web UI:
- Attach to a LAN port on the router.
- Connect to the Linksys Smart WiFi Page (default 192.168.1.1) and login
- Select the connectivity tab on the left
- In the manual update box on the right
- Select browse, and browse to
  openwrt-ipq40xx-linksys_ea6350v3-squashfs-factory.bin
- Click update.
- Read and accept the warning
- The router LED will start blinking. When the router LED goes solid, you
  can now navigate to 192.168.1.1 to your new OpenWrt installation.

Sysupgrade:
- Flash the sysupgrade image as usual. Please: try to do a reset everytime
  you can (doing it with LuCI is easy and can be done in the same step).

Recovery (Automatic):
- If the device fails to boot after install or upgrade, whilst the unit is
  turned on:
1 - Wait 15 seconds
2 - Switch Off and Wait 10 seconds
3 - Switch on
4 - Repeat steps 1 to 3, 3 times then go to 5.
5 - U-boot will have now erased the failed update and switched back to the
    last working firmware - you should be able to access your router on
    LAN.

Recovery (Manual):
- The steps for manual recovery are the same as the generic u-boot tftp
  client method.

Back To Stock:
- Use the generic recovery using the tftp client method to flash the
  "civic.img". Also you can strip-and-pad the original image and use
  the generic "mtd" method by flashing over the "kernel" partition.
* Just be careful to flash in the partition that the device is currently
  booted.

Signed-off-by: Ryan Pannell <ryan@osukl.com>
Signed-off-by: Oever González <notengobattery@gmail.com>
[minor edits, removed second compatible of nand, added dtb entry to 4.19]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-26 21:43:11 +01:00
Christian Lamparter
b2e1333de3 ipq40xx: 4.19: fix pcie wifi unit-address of the MR33 and A62
The unit address should be wifi@1,0 since the device is located
at 0000:01:00.0.

Reported-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-26 17:10:19 +01:00
David Bauer
25eb02ae8e ipq40xx: remove misplaced MR33 UCI definition
This removes the misplaced UCI-network configuration for the MR33. The
LAN port is set in 01_leds while it is already correctly defined in
02_network.

This was most likely an oversight as no network configuration belongs
into 01_leds.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-26 10:45:34 +01:00
Petr Štetiar
540a7d1ecc ipq40xx: dts: Unify naming of gpio-led nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-01-24 15:53:03 +01:00
Petr Štetiar
98c6c8cdfe ipq40xx: dts: Unify naming of gpio-keys nodes
In DTS Checklist[1] we're now demanding proper generic node names, as
the name of a node should reflect the function of the device and use
generic name for that[2]. Everybody seems to be copy&pasting from DTS
files available in the repository today, so let's unify that naming
there as well and provide proper examples.

1. https://openwrt.org/submitting-patches#dts_checklist
2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation

Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
2019-01-24 15:53:03 +01:00
Stijn Tintel
a37098a2d0 kernel: bump 4.19 to 4.19.16
Refresh patches.
Remove upstreamed patches:
- backport/096-mips-math-emu-Write-protect-delay-slot-emulation-pages.patch
- backport/096-v4.20-netfilter-ipv6-Preserve-link-scope-traffic-original-.patch
- backport/424-v4.20-net-dsa-fix-88e6060-roaming.patch
- hack/100-mtd-rawnand-qcom-fix-memory-corruption-that-causes-p.patch
- pending/510-f2fs-fix-sanity_check_raw_super-on-big-endian-machines.patch
Update patch that no longer applies:
- backport/343-netfilter-nft_flow_offload-handle-netdevice-events-f.patch

Compile-tested: mesongx
Runtime-tested: mesongx

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2019-01-17 03:04:13 +02:00
Koen Vandeputte
f56a4e809b kernel: bump 4.14 to 4.14.91
Refreshed all patches.

Removed upstreamed:
- 500-ubifs-Handle-re-linking-of-inodes-correctly-while-re.patch

Compile-tested on: ar71xx, cns3xxx, imx6
Runtime-tested on: ar71xx, cns3xxx, imx6

Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
2019-01-07 17:09:06 +01:00
David Bauer
634c733065 ipq40xx: copy Fritz4040 UBoot to STAGING_DIR_IMAGE
Copy U-Boot to STAGING_DIR_IMAGE (and append it to the EVA-image from
there) to fix image generation using the image-builder.

Also remove the bootloader from DEVICE_PACKAGES and instead use the
BUILD_DEVICES directive from within the U-Boot makefile.

This fixes eva-image generation using the OpenWRT image-builder.

Signed-off-by: David Bauer <mail@david-bauer.net>
2019-01-06 12:26:12 +01:00
Robert Marko
bba1428274 ipq40xx: 4.14: Sync kernel config
This patch syncs the 4.14 kernel config to the
current generic configuration.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
2019-01-05 22:23:41 +01:00
Robert Marko
0c1f1dab59 ipq40xx: 4.19: Sync kernel config
This patch syncs the 4.19 kernel config since the
KERNEL_STACKPROTECTOR and compiler options are
now part of the 4.19 generic config.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
2019-01-05 22:23:41 +01:00
Christian Lamparter
32e953b821 ipq40xx: fix 4.14 ImageBuilder build woes
Robert Marko reported an issue with the current imagebuilder images:
"Imagebuilder includes the new kmod-usb-dwc3-qcom USB driver
package by default even on 4.14. [...] the current state imagebuilder
can't build images under 4.14 at all as the kmod-usb-dwc3-qcom does
not exist in it so it throws and error and exits."

This patch reverts the Makefile to just kmod-usb-dwc3-of-simple and
once the switch to 4.19 is done. It also removes the
kmod-usb-phy-qcom-dwc3 as they only contain the usb-phy drivers for
the ipq806x generation.

Dynamic switching based on the KERNEL_PATCHVER is possible by using:
   $(if $(filter 4.14,$(KERNEL_PATCHVER)),kmod-usb-dwc3-of-simple,kmod-usb-dwc3-qcom)
though it

Fixes: 13321fa142 ("ipq40xx: Use kmod-usb-dwc3-qcom by default")
Fixes: 6e58fb2c33 ("ipq40xx: kmod-usb-dwc3-of-simple vs kmod-usb-dwc3-qcom")
Reported-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2019-01-05 22:23:10 +01:00
Christian Lamparter
ef5ff08662 ipq40xx: convert to device-tree based USB LED trigger
Thanks to the ledtrig-usb.c the USB LED trigger can be
setup in the device-tree definition for the Asus RT-AC58U
and ZyXEL NBG6617.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-27 14:36:23 +01:00
Christian Lamparter
ee5d3a6d7c ipq40xx: fix warning triggered by bad interrupt definition
This patch fixes a kernel warning that got triggered by 4.19
because of a bad/missing interrupt level definition in the DTS.

| WARNING: CPU: 2 PID: 1996 at drivers/irqchip/irq-gic.c:1016
| CPU: 2 PID: 1996 Comm: kmodloader Not tainted 4.19.9 #0
| Hardware name: Generic DT based system
| [<c0317884>] (warn_slowpath_null) from [<c04f9cd0>]
| [<c04f9cd0>] (gic_irq_domain_translate) from [<c035af30>]
| [<c035af30>] (irq_create_fwspec_mapping) from [<c035b1e0>]
| [<c035b1e0>] (irq_create_of_mapping) from [<c0614eec>]
| [<c0614eec>] (of_irq_get) from [<c0614f3c>]
| [<c0614f3c>] (of_irq_to_resource) from [<c0614ff0>]
| [<c0614ff0>] (of_irq_to_resource_table) from [<c0610e08>]
| [<c0610e08>] (of_device_alloc) from [<c0610ea0>]
| [<c0610ea0>] (of_platform_device_create_pdata)
| [<c061120c>] (of_platform_bus_create)
| [<c06113c4>] (of_platform_populate)
| [<bf4c06b4>] (dwc3_qcom_probe [dwc3_qcom])

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-27 14:36:23 +01:00
Christian Lamparter
6e58fb2c33 ipq40xx: kmod-usb-dwc3-of-simple vs kmod-usb-dwc3-qcom
Robert Marko <robimarko@gmail.com> noted in
"ipq40xx: Use kmod-usb-dwc3-qcom by default":
| Since 4.18 we cant use DWC3 OF Simple anymore so we
| have to use kmod-usb-dwc3-qcom.

This patch adds a TODO right next to the KERNEL_PATCHVER so
it will be picked up when moving to 4.19.

I would also like to point out:

All users/devs that are compiling their own images from source
and have a existing 4.14 config and want to switch to 4.19:

Please drop kmod-usb-dwc3-of-simple and add kmod-usb-dwc3-qcom
module package. Otherwise, the USB port on your router will no
longer work.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-27 14:36:23 +01:00
Christian Lamparter
a5ac9030ed ipq40xx: MR33: device-tree update
- 4.19 no longer refuses to initialize the mdio bus if
   a phy is not connected.

 - fix partition unit-address

 - restrict partition offset and size to 32-bit integers.

 - add note to warn people not to mess with the ubi
   partition size.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-27 14:36:23 +01:00
Christian Lamparter
a2501ebfb0 ipq40xx: remove qcom,ipq4019 on all devices
Upstream commit:
80483c3abf8 ("ARM: qcom: Cleanup/Remove unnecessary board file")
removed all the platform device compatibles stating that:
"This patch removes the unnecessary board file. The generic machine
definition is sufficient for the Qualcomm platforms."

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-27 14:30:45 +01:00
Christian Lamparter
00dd84ca2e ipq40xx: rt-ac58u: fix device-tree snafu
- make the device userspace integration (WIFI,MAC,sysupgrade)
   work again by renaming the ubi to UBI_DEV as a temporary measure.
   In the future, once 4.14 support is dropped, this can all be
   refactored again. *sigh*

 - use the wifi0 and wifi1 labels

 - follow Device-Tree Release v0.2 2.2.2 Generic Names Recommendation

 - fix duplicated partition node-names

 - remove qcom,ipq4019 platform compatible. it's no longer needed
   (and wrong because the chip is a qcom,ipq4018).

Fixes: 4c67f3ad78d ("ipq40xx: Adapt 4.19 DTS for upstream SPI-NAND driver")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-27 14:30:45 +01:00
Robert Marko
077a63db1d ipq40xx: 4.19: Enable pseudo random number generator
IPQ40xx series has a HW pseudo random number generator built in.
It already has a node in the upstream ipq4019.dtsi so we just need to enable it.
Its driver has been rewritten to use crypto API so we dont have char interface like under 4.14 kernel.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-12-27 14:30:45 +01:00
Robert Marko
59485f7486 ipq40xx: files-4.19: Clear some DTC warnings
DTC was throwing warnings like this:
image-qcom-ipq4018-jalapeno.dtb: Warning (avoid_unnecessary_addr_size): /soc/spi@78b5000/m25p80@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
image-qcom-ipq4018-jalapeno.dtb: Warning (avoid_unnecessary_addr_size): /soc/spi@78b5000/spi-nand@1: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property

So lets fix this for our downstream boards.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-12-27 14:30:45 +01:00
Robert Marko
c29c8838a1 ipq40xx: Use upstream SPI-NAND driver instead of MT29F
Since 4.19 upstream kernel provides generic SPI-NAND
framework and vendor specific drivers.
Since only users of MT29F are 2 boards with Winbond
W25N01GV SPI-NAND for which support has been backported
from 4.20 we can drop the ever stuck in staging MT29F
driver and instead use the upstream driver.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [squashed]
2018-12-27 14:26:07 +01:00
Robert Marko
13321fa142 ipq40xx: Use kmod-usb-dwc3-qcom by default
Since 4.18 we cant use DWC3 OF Simple anymore so we have to use
kmod-usb-dwc3-qcom.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-12-27 14:06:38 +01:00
Robert Marko
30f2b22952 ipq40xx: Add 4.19 kernel config
This adds the neccessary 4.19 kernel config.

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-12-27 14:06:38 +01:00
Robert Marko
8b7abea2f6 ipq40xx: Add patches for 4.19
This adds the necessary patches for 4.19 kernel.
Upstreamed patches were dropped, backported upstreamed patches
from 4.20.
Drop Winbond ID patch since that NAND IC was upstreamed to use
SPI-NAND framework and support for it was backported from 4.20.
Rework ESSEDMA patches to compile under 4.19 due to timer changes,
Clément Péron did the hard work and his changes were taken from the
initial 4.19 PR.
MR33 changes had to be manually refreshed to apply.
Refresh other patches to apply.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove
2018-12-27 14:06:38 +01:00
Robert Marko
96b69c2e9a ipq40xx: Add files for 4.19
This copies over files from 4.14

Signed-off-by: Robert Marko <robimarko@gmail.com>
2018-12-27 14:06:38 +01:00
Christian Lamparter
360efb1ead ipq40xx: NBG6617: add usb-ledtrig-usbport to DEVICE_PACKAGES
The ZyXEL NBG6617 USB LED was not working with the default images.
It turned out that kmod-usb-ledtrig-usbport was missing from the
default installation.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2018-12-22 15:08:24 +01:00
David Bauer
b53111ad42 ipq40xx: disable kernel-padding for DNI image
This commit removes the fixed kernel size-padding for the Netgear
DNI image creation as it is not necessary for a working image.

The fake rootfs still needs to be padded to the blocksize.

Tested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
2018-12-20 23:54:24 +01:00