Xiaomi MiWiFi Nano is based on Mediatek MT7628 with 64MB ram 16MB flash
Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com>
v3 includes changes suggested by L. D. Pinney & Karl Palsson-
Eliminate en25q64 (4MB) flash chip
Alphabetization
Remove hyphen in model
Rename profile from miwifinano.mk to xiaomi.mk
Add gpios that are attached to leds
SVN-Revision: 49024
Explicit sets the size of the mtdparts, because the kernel has also an explicit value.
If they have diffent sizes the ubi won't be detected.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49018
otherwise the uboot is missing important commands like bootz
Signed-off-by: Martin Mueller <mm@sig21.net>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49017
Since switching to new ubi(kernel,squashfs,ubifs) layout, the kernel lies in a
ubi volume. Dropping the mtd parts because the mtd layout is saved in the
device-tree, which is appended to the zImage.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
SVN-Revision: 49016
Add support for Xilinx ZC702 Dev board
Zynq target is using 4.4 kernel and mainline 2016.1 u-boot.
Patch is tested with Xilinx ZC702 Dev board with SD boot mode.
known issues:
- no QSPI driver in 4.4 kernel: no QSPI flash support
- USB is not working in 4.4 kernel
Signed-off-by: Jason Wu <jason.wu.misc@gmail.com>
create mode 100644 package/boot/uboot-zynq/Makefile
create mode 100644 target/linux/zynq/Makefile
create mode 100644 target/linux/zynq/base-files.mk
create mode 100755 target/linux/zynq/base-files/etc/board.d/02_network
create mode 100644 target/linux/zynq/base-files/etc/config/network
create mode 100644 target/linux/zynq/base-files/etc/inittab
create mode 100644 target/linux/zynq/config-4.4
create mode 100644 target/linux/zynq/image/Makefile
create mode 100755 target/linux/zynq/image/mkits.sh
create mode 100644 target/linux/zynq/patches-4.4/0001-arm-dts-zynq-zc702.dts-Set-default-rdinit-to-sbin-in.patch
create mode 100644 target/linux/zynq/profiles/zc702.mk
SVN-Revision: 48697
U-boot ships with the `mx6qsabresd` configuration file to configure a
bootloader suitable for booting the Freescale i.MX6q SABRE evaluation board
from SD card. Expose this option in the uboot-imx6 Makefile.
Signed-off-by: Keno Fischer <keno@juliacomputing.com>
SVN-Revision: 48014
OpenWrt configuration part of support for the PowerCloud Systems
CR5000. The CR5000 is a dual-band 802.11n wireless router with
8MB flash, 64MB RAM, (unused on stock firmware) USB 2.0 port and
five port gigabit ethernet switch. The CR5000 was sold as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47946
OpenWRt configuration part of support for the PowerCloud
Systems CR3000. The CR3000 is a 802.11n 2.4 GHz wireless router with
8MB flash, 64MB RAM, a four port gigabit ethernet switch, and a fast
ethernet wan port that was sold by PowerCloud Systems as
hardware for the Skydog cloud-managed router service.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47945
Openwrt configuration part of support for PowerCloud CAP324
Cloud AP. The CAP324 Cloud AP is a device sold by PowerCloud Systems
who's stock firmware (CloudCommand) provides 'cloud' based managment
of large numbers access points.
The CAP324 is a dual-band 802.11n wireless access point with 16MB flash
and 128MB RAM and single gigabit ethernet port. It can be powered via PoE
or a wall wart.
Signed-off-by: Daniel Dickinson <openwrt@daniel.thecshore.com>
SVN-Revision: 47944
- tested on Beagleboard C4
- remove upstream patches
- disable THUMB mode on OMAP3 this increases binary size
(remove CONFIG_SYS_THUMB_BUILD)
- reduce SPL size by disabling EXT feature
(remove CONFIG_SPL_EXT_SUPPORT)
this fixes 2015.07 and 2015.10-rc3
Beagleboard C4 booting
which were broken by upstream commit
with id: bd2c4522c26d535515aebca52d27c004a7e0c05c
Arm THUMB mode is broken because of an yet unknown errata
see: http://lists.denx.de/pipermail/u-boot/2015-August/225793.html
- backport upstream fix that was introduced in 2015.10-rc5
and was not fixed in 2015.10 final
Signed-off-by: Dirk Neukirchen <dirkneukirchen@web.de>
SVN-Revision: 47924
gcc-5 handles inline without static differently and that makes
uboot-mxs fail to build. Remove the inline so it gets exported and can
be used in other functions.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SVN-Revision: 47533
- Use board engineering names rather than marketing names
- Linksys uses a dual firmware layout, where the bootloader
will switch to the other stored image when one fails to
boot three consecutive times.
In order to make this firmware compatible with the factory
images and the stock bootloader we must match this layout.
Signed-off-by: Claudio Leite <leitec@staticky.com>
SVN-Revision: 47429
The current patch to add Duckbill support is wrong and does not
even compile. So replace this patch with a working one.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
SVN-Revision: 47007
Install uboot files to KERNEL_BUILD_DIR instead of BIN_DIR to fix
ImageBuilder. Similar fixes are necessary for many (all?) other uboot
targets.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
SVN-Revision: 46605
