The Alcatel HH40V is a CAT4 LTE router used by various ISPs.
Specifications
==============
SoC: QCA9531 650MHz
RAM: 128MiB
Flash: 32MiB SPI NOR
LAN: 1x 10/100MBit
WAN: 1x 10/100MBit
LTE: MDM9607 USB 2.0 (rndis configuration)
WiFi: 802.11n (SoC integrated)
MAC address assignment
======================
There are three MAC addresses stored in the flash ROM, the assignment
follows stock. The MAC on the label is the WiFi MAC address.
Installation (TFTP)
===================
1. Connect serial console
2. Configure static IP to 192.168.1.112
3. Put OpenWrt factory.bin file as firmware-system.bin
4. Press Power + WPS and plug in power
5. Keep buttons pressed until TFTP requests are visible
6. Wait for the system to finish flashing and wait for reboot
7. Bootup will fail as the kernel offset is wrong
8. Run "setenv bootcmd bootm 0x9f150000"
9. Reset board and enjoy OpenWrt
Installation (without UART)
===========================
Installation without UART is a bit tricky and requires several steps too
long for the commit message. Basic steps:
1. Create configure backup
2. Patch backup file to enable SSH
3. Login via SSH and configure the new bootcmd
3. Flash OpenWrt factory.bin image manually (sysupgrade doesn't work)
More detailed instructions will be provided on the Wiki page.
Tested by: Christian Heuff <christian@heuff.at>
Signed-off-by: Andreas Böhler <dev@aboehler.at>
The RTL8366S/RB switch node in DTS defines "mii-bus = <&mdio0>" to permit
management via SMI but this has likely never worked, instead falling back
to using GPIOs in the past:
rtl8366s switch: cannot find mdio bus from bus handle (yet)
rtl8366s switch: using GPIO pins 19 (SDA) and 20 (SCK)
rtl8366s switch: RTL8366 ver. 1 chip found
Recently, the rtl8366s and rtl8366_smi drivers were changed from built-in
to loadable modules. This affected driver probing order and caused switch
initialization (and network access) to fail:
rtl8366s switch: using MDIO bus 'ag71xx_mdio'
rtl8366s switch: unknown chip id (ffff)
rtl8366s switch: chip detection failed, err=-19
Force using GPIOs to manage the switch by dropping the "mii-bus" DTS
definition, which works for both built-in and loadable switch drivers.
Fixes: 6e0f0eae5b ("ath79: use rtl8366s and rtl8366_smi as a module")
Fixes: 575ec7a4b1 ("ath79: use rtl8366rb as a module")
Tested-by: Tony Ambardar <itugrok@yahoo.com> # WZR-HP-G300NH (RTL8366S)
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Switch drivers for RTL8366S/RB were packaged as modules but not properly
added to device definitions for WZR-HP-G300NH router variants, breaking
network access to both after installation or upgrade.
Assign the correct switch driver package for each router.
Fixes: 6e0f0eae5b ("ath79: use rtl8366s and rtl8366_smi as a module")
Fixes: 575ec7a4b1 ("ath79: use rtl8366rb as a module")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This fixes a well known "LZMA ERROR 1" error, reported previously on
numerous of similar devices.
Fixes: #11919
Signed-off-by: Haoan Li <lihaoan1001@163.com>
Apart from the embedded BCM63268 wireless, this device has an external BCM4360
connected by PCIe which needs a fallback SPROM.
b43 isn't enabled for this device because BCM4360 isn't supported (AC PHY).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Apart from the embedded BCM6362 wireless, Netgear DGND3700v2 has external
BCM43228 wireless connected by PCIe.
Fallback SPROM isn't needed for this one because it has a physical SPROM.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
late_initcall_sync() is no longer needed so standard module functions can be
used on all bmips PCI/PCIe drivers.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
By default both kmod-bcma and kmod-ssb are selected by kmod-b43.
However, only one of both modules is needed for bmips subtargets:
- bcma: bcm6318, bcm6328, bcm6362, bcm63268
- ssb: bcm6358, bcm6368
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Stop using bmips b43-sprom fixups and switch to generic bcma/ssb fallback
SPROMs. This way we don't need to include the b43-sprom fixups on devices
without Broadcom wireless.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This adds generic kernel support for Broadcom Fallback SPROMs so that it can be
used in any target, even non Broadcom ones.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This adds a new package with Broadcom SPROMs that can be used as fallback when
the devices lack physical SPROMs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
A patch was added in kernel 5.4 to support the fiber operation of
AR8033 with ramips devices. In kernel 5.18 similar enhancements
were added to the kernel. Those patches are required for other
fiber based devices but when added, build fails for ramips targets.
This commit removes the ramips patch and adds the kernel 5.18 ones.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
[ split commit,refresh patch and improve commit message ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
A patch was added in kernel 5.4 to support the fiber operation of
AR8033 with ramips devices. In kernel 5.18 similar enhancements
were added to the kernel. Those patches are required for other
fiber based devices but when added, build fails for ramips targets.
This commit removes the ramips patch and adds the kernel 5.18 ones.
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
[ split commit, refresh patch and improve commit title ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Replace pending 730-net-phy-at803x-fix-feature-detection.patch with
upstream version and move it to backport.
Refresh other related patch while moving it.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Upload proposed refreshed patches if the check fails.
This should help devs refresh the patches if they don't have access to a
buildroot.
Devs should ALWAYS refresh the patches before submitting and merging
commits.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The patch needs to be refreshed to apply cleanly.
Fixes: 998b973157 ("kernel: net: phy: realtek: improve RealTek 2.5G PHY driver")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware specification:
SoC: MediaTek MT7986A 4x A53
Flash: ESMT F50L1G41LB 128MB
RAM: ESMT M15T4G16256A 512MB
Ethernet (Max Speed):
XDR4288: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan
XDR6086: 1x 2.5G Wan, 1x 2.5G Lan, 1x 1G Lan
XDR6088: 1x 2.5G Wan, 1x 2.5G Lan, 4x 1G Lan
WiFi:
XDR4288: MT7976DAN (2.4G 2T2R, 5G 3T3R)
XDR6086/XDR6088:
WiFi1: MT7976GN 2.4GHz 4T4R
WiFi2: MT7976AN 5GHz 4T4R
Button: Reset, WPS, Turbo
USB: 1 x USB 3.0
Power: DC 12V 4A
Flash instructions:
1. Execute the following operation to open nc shell:
https://openwrt.org/inbox/toh/tp-link/xdr-6086#rooting
2. Replace the stock bootloader to OpenWrt's:
dd bs=131072 conv=sync of=/dev/mtdblock9 if=/tmp/xxx-preloader.bin
dd bs=131072 conv=sync of=/dev/mtdblock9 seek=28 if=/tmp/xxx-bl31-uboot.fip
3. Connect to your PC via the Gigabit port of the router,
set a static ip on the ethernet interface of your PC.
(ip 192.168.1.254, gateway 192.168.1.1)
4. Download the initramfs image, and restart the router,
waiting for tftp recovery to complete.
5. After openwrt boots up, perform sysupgrade.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
[Add uboot build, fit and sysupgrade support, fix RealTek PHYs]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
TP-Link TL-XDR608x comes with locked vendor loader. Add U-Boot build
for replacement loader for both TL-XDR6086 and TL-XDR6088. The only
difference at U-Boot level is the different filename requested via
TFTP, matching the corresponding OpenWrt build artifacts for each
device.
The TP-Link TL-XDR4288 has the same hardware as the TP-Link TL-XDR6088
except for the wireless part. Also create a uboot for the TP-Link
TL-XDR4288.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[rebase to uboot 23.04, correct led and button]
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* use interface mode switching only when operating in C45 mode
Linux prevents switching the interface mode when using C22 MDIO,
hence use rate-adapter mode in case the PHY controlled via C22.
* use phy_read_paged where appropriate
* use existing generic inline functions to handle 10GbE advertisements
instead of redundantly defining register macros in realtek.c which
are not actually vendor-specific.
* make sure 10GbE advertisement is valid, preventing false-positive
warning "Downshift occurred from negotiated speed 2.5Gbps to actual
speed 1Gbps, check cabling!" with some link-partners using 1G mode.
* Support Link Down Power Saving Mode (ALDPS)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of use mac-address-ascii in nvmem_get_mac_address
function, move it into of_get_mac_addr_nvmem function to
support more devices.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
The Config partition of some machines is special, and the openwrt script
cannot read the protest_lan_mac correctly. This problem can be solved by
reading the mac address (ascii) in dts.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Fix the network configuration according to the device tree.
Fixes: 5faff99 ("mediatek: filogic: fix mt7986a ethernet devicetree entries")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Due to us keeping a patch around for years and never proposing it to
squashfs4 repository, we resulted in having the same squashfs4 version
but with different supported options. (openwrt patched -- upstream)
To workaround this problem, a non-standard option was required.
To not have surprise on tool bump, backport the patch and add the new
config option required to enable these extended non-standard options.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
U-Boot commit ea6fdc13595 ("dm: button: add support for linux_code in
button-gpio.c driver") makes it mandatory to specify linux,code for all
buttons. As that broke handling of the reset button in U-Boot with the
update to U-Boot 2023.04, add linux,code for all butons.
Reported-by: @DragonBluep
Fixes: 50f7c5af4a ("uboot-mediatek: update to v2023.04")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
According to SinoVoip up to 3A @ 3.3V are available for both
SFP modules together. Raise energy limit from 1W (default) to 3W,
however, be aware that using modules consuming more than 1W will
require active cooling!
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
qrtr/ns.ko is now merged into qrtr/qrtr.ko, so drop the individual module packaging.
Fixes: f4989239cc ("kernel: bump 5.15 to 5.15.107")
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> #ipq807x/ax3600, x86_64/FW-7543B, mt7621/dap-x1860
upstream PR 408 improvements:
-Fix AMSDU packets unused
-Removed the ASMDU packets queue
-Add more info in the iw tool
-fix is_hw_crypto_enabled
-Optimization AMPDU_TX_OPERATIONAL (avoid a spinlock)
change to wongsyrone mod
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
`bzip2` is the standard executable for bzip2 compression
this includes development includes and both static and shared libs
(libbz2) which can be used by other packages
the initramfs generator offers the BZIP2 option but there was no
executable to support it, and worked only via side effect of having a
system-installed version of bzip2, which could be less predictable
Signed-off-by: Tony Butler <spudz76@gmail.com>
[ remove unintended change ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This reverts commit 394d7134ec.
The commit has unintentded change that cause compilation error with SDK
or LZO compression.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
QCA has finally sent a proper fixup for the 160MHz regression upstream,
so lets use the pending fix which also properly sets center frequency 2
in case 80+80 MHz is used.
Signed-off-by: Robert Marko <robimarko@gmail.com>
