a4355a6 firewall3: clean up the flow table detection logic
edd0dc5 firewall3: create a common helper to find strings in files
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This includes several improvements and fixes:
61db17e rules: fix device and chain usage for DSCP/MARK targets
7b844f4 zone: avoid duplicates in devices list
c2c72c6 firewall3: remove last remaining sprintf()
12f6f14 iptables: fix serializing multiple weekdays
00f27ab firewall3: fix duplicate defaults section detection
e8f2d8f ipsets: allow blank/commented lines with loadfile
8c2f9fa fw3: zones: limit zone names to 11 bytes
78d52a2 options: fix parsing of boolean attributes
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Moved to packages repo because it was considered
non-essential for most router configurations.
Signed-off-by: Jan Pavlinec <jan.pavlinec@nic.cz>
[shorten commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Instead of doing uci commit and reload_config for each setting do it
only once when one of these options was changed. This should make it a
little faster when both conditions are taken.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Without this change the config is only committed, but the uhttpd daemon
is not reloaded. This reload is needed to apply the config. Without the
reload of uhttpd, the ubus server is not available over http and returns
a Error 404.
This caused problems when installing luci on the snapshots and
accessing it without reloading uhttpd.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Now that ujail supports seccomp also on Aarch64, add missing syscall
'fstat' to the list of allowed syscalls.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This change was investigated previously [1] but not deemed necessary. With
the recent addition [2] of modern BPF loader support, however, tc gained
dependencies on libelf and libbpf, with a larger installation footprint.
Similar to ip-tiny/ip-full, split tc into tc-full and tc-tiny variants,
where the latter excludes the eBPF loader, uses a smaller executable, and
avoids libelf and libbpf package dependencies. Both variants provide the
'tc' virtual package, with tc-tiny as the default.
The previous tc package included a loadable module for iptables actions.
Separate this out into a common package, tc-mod-iptables, which both
variants depend on. Some package sizes on mips_24kc:
Before:
148343 tc_5.11.0-1_mips_24kc.ipk
After:
144833 tc-full_5.11.0-2_mips_24kc.ipk
138430 tc-tiny_5.11.0-2_mips_24kc.ipk (and no libelf or libbpf)
4115 tc-mod-iptables_5.11.0-2_mips_24kc.ipk
Also fix up some Makefile indentation.
[1] https://github.com/openwrt/openwrt/pull/1627#issuecomment-447619962
[2] b048a305a3 ("iproute2: update to 5.11.0")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The link equalizer sch_teql.ko of package kmod-sched relies on a hotplug
script historically included in iproute2's tc package. In previous
discussion [1], consensus was the hotplug script is best located together
with the module in kmod-sched, but this change was deferred at the time.
Relocate the hotplug script now. This change also simplifies adding a tc
variant for minimal size with reduced functionality.
[1] https://github.com/openwrt/openwrt/pull/1627#issuecomment-447923636
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This patch has been submitted upstream to fix an error reported by a few
users. One instance seen using gcc 10.2.0, binutils 2.35.1 and musl 1.1.24:
bpf_glue.c: In function 'get_libbpf_version':
bpf_glue.c:46:11: error: 'PATH_MAX' undeclared (first use in this function);
did you mean 'AF_MAX'?
46 | char buf[PATH_MAX], *s;
| ^~~~~~~~
| AF_MAX
Reported-by: Rui Salvaterra <rsalvaterra@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
If the environment variable FILTER is set before compilation,
compilation of the ppp-package will fail with the error message
Package ppp is missing dependencies for the following libraries:
libpcap.so.1
The reason is that the OpenWrt-patch for the Makefile only comments
out the line FILTER=y. Hence the pcap-library will be dynamically
linked if the environment variable FILTER is set elsewhere, which
causes compilation to fail. The fix consists on explicitly unsetting
the variable FILTER instead.
Signed-off-by: Eike Ritter <git@rittere.co.uk>
[ -d /sys/module/xfrm_interface ] is enough to check if
CONFIG_XFRM_INTERFACE support was enabled in kernel.
Signed-off-by: Alin Nastac <alin.nastac@technicolor.com>
Document the existence of this feature. This allows the user to execute a script
at each DHCPv4 event. This is useful, for example, as an ad-hoc way to update a
DDNS entry when (and only when) required.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Document the existence of this feature. This allows the user to execute a script
at each DHCPv6 event. This is useful, for example, as an ad-hoc way to update a
DDNS entry when (and only when) required.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Fix: bpftools 5.11.2 does not compile on macOS, because the -m option
was placed between src and dst. Corrected by moving -m 644 before src.
Signed-off-by: Georgi Valkov <gvalkov@abv.bg>
The pkgconfig file hardcodes a host library directory which cannot be
overridden by OpenWrt during builds. Use SED to fix this and potential
include directory problems, as is done with several other packages.
This fixes a strange issue intermittently seen building iproute2 on the
oxnas target:
iptables modules directory: /usr/lib/iptables
libc has setns: yes
SELinux support: no
libbpf support: no
libbpf version 0.3.0 is too low, please update it to at least 0.1.0
LIBBPF_FORCE=on set, but couldn't find a usable libbpf
Fixes: 2f0d672088 ("bpftools: add utility and library packages
supporting eBPF usage")
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
This will use the new application led trigger backend. For now this is
the only package that uses leds trigger in user space to configure the
kernel led triggers.
The callback script only emmits a message for now, so that this LED is now
managed by the rssileds service. Until now a generic warning was emitted that
this LED trigger is not supported. But that is not true.
-> Skipping trigger 'rssileds' for led '<name>' due to missing kernel module
I think this callback should be changed in the future to restart the
service.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
p2p_add_device() may remove the oldest entry if there is no room in the
peer table for a new peer. This would result in any pointer to that
removed entry becoming stale. A corner case with an invalid PD Request
frame could result in such a case ending up using (read+write) freed
memory. This could only by triggered when the peer table has reached its
maximum size and the PD Request frame is received from the P2P Device
Address of the oldest remaining entry and the frame has incorrect P2P
Device Address in the payload.
Fix this by fetching the dev pointer again after having called
p2p_add_device() so that the stale pointer cannot be used.
This fixes the following security vulnerabilities/bugs:
- CVE-2021-27803 - A vulnerability was discovered in how p2p/p2p_pd.c
in wpa_supplicant before 2.10 processes P2P (Wi-Fi Direct) provision
discovery requests. It could result in denial of service or other
impact (potentially execution of arbitrary code), for an attacker
within radio range.
Fixes: 17bef1e97a50 ("P2P: Add peer entry based on Provision Discovery Request")
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Changes:
- Remove custom Build/Compile because it's no longer needed
- Remove std=gnu99 which is added automaticaly by igmpproxy if needed
- Remove -Dlog from CFLAGS because igmpproxy doesn't have log function
Signed-off-by: Jan Pavlinec <jan.pavlinec@nic.cz>
Compile and run-tested on malta/mip32be, using bpftool directly and also
libbpf (linked with tc) to inspect and load simple eBPF programs.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The latest iproute2 version brings various improvements and fixes:
https://git.kernel.org/pub/scm/network/iproute2/iproute2.git/log/?qt=range&q=v5.10.0..v5.11.0
In particular, ip and tc now use libbpf as the standard way to load BPF
programs, rather than the old, limited custom loader. This allows more
consistent and featureful BPF program handling e.g. support for global
initialized variables.
Also fix a longstanding problem with iproute2 builds where unneeded DSO
dependencies are added to most utilities, bloating their installation
footprint. From research and testing, explicitly using a "--as-needed"
linker flag avoids the issue. Update accordingly and drop extra package
dependencies from Makefile.
Additional build and packaging updates include:
- install missing development header to iproute2/bpf_elf.h
- propagate OpenWrt verbose flag during build
- update and refresh patches
Compile and run tested: QEMU/malta-mips32be on kernels 5.4 & 5.10.
All iproute2 packages were built and installed to the test image. Some
regression testing using ip-full and tc was successfully performed to
exercise several kmods, tc modules, and simple BPF programs.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The following warnings are shown during build:
/usr/include/vdsl/cmv_message_format.h:33:6: warning: "MEI_SUPPORT_DEBUG_STREAMS" is not defined, evaluates to 0 [-Wundef]
#if (MEI_SUPPORT_DEBUG_STREAMS == 1)
^~~~~~~~~~~~~~~~~~~~~~~~~
/usr/include/vdsl/drv_mei_cpe_interface.h:2256:6: warning: "MEI_SUPPORT_OPTIMIZED_FW_DL" is not defined, evaluates to 0 [-Wundef]
#if (MEI_SUPPORT_OPTIMIZED_FW_DL == 1)
^~~~~~~~~~~~~~~~~~~~~~~~~~~
The headers are provided by the MEI driver, but the defines are never
set by the vdsl app. While the struct with the
MEI_SUPPORT_OPTIMIZED_FW_DL conditional isn't used by the vdsl app,
however CMV_USED_PAYLOAD_8BIT_SIZE which value depends on
MEI_SUPPORT_DEBUG_STREAMS is.
Since the MEI driver doesn't provide an autogenerated header with
compile flags, the flags are hardcoded for the vdsl app.
Set them for the MEI driver as well, to indicate a relation to the
values used for the vdsl app and to be not surprised by a changed
default in case the MEI driver gets updated. Use the current default
values defined in the MEI driver.
Signed-off-by: Mathias Kresin <dev@kresin.me>
To the vast majority of the users, wireguard-tools are not useful
without the underlying kernel module. The cornercase of only generating
keys and not using the secure tunnel is something that won't be done on
an embedded OpenWrt system often. On the other hand, maintaining a
separate meta-package only for this use case introduces extra
complexity. WireGuard changes for Linux 5.10 remove the meta-package.
So let's make wireguard-tools depend on kmod-wireguard
to make WireGuard easier to use without having to install multiple
packages.
Fixes: ea980fb9 ("wireguard: bump to 20191226")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
On Linux 5.4, build WireGuard from backports. Linux 5.10 contains
wireguard in-tree.
Add in-kernel crypto libraries required by WireGuard along with
arch-specific optimizations.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Upstream integrated multiple patches from Distributions and did other
changes:
* rp-pppoe.so was renamed to pppoe.so
* Converted to ANSI C
The following patches were applied upstream:
* 100-debian_ip-ip_option.patch
* 101-debian_close_dev_ppp.patch
* 103-debian_fix_link_pidfile.patch
* 106-debian_stripMSdomain.patch
* 107-debian_pppoatm_wildcard.patch
* 110-debian_defaultroute.patch
* 202-no_strip.patch
Compilation with musl libc was fixed upstream so
140-pppoe_compile_fix.patch is not needed any more
Parts of the 203-opt_flags.patch patch were applied in a different way
upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
There are efforts underway to bring wireguard in-tree for Linux 5.4 and
to have a common build infrastructure for both 5.4 and 5.10 for
kmod-wireguard[0]. Until then, restrict kmod-wireguard to build only on
Linux 5.4, because the wireguard-compat package will not build on Linux
5.10.
[0]: https://github.com/openwrt/openwrt/pull/3885
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
This is a backport of the upstream commit 58bbbb598144 ("nl80211: Ignore
4addr mode enabling error if it was already enabled") which fixes same
issue as in the current fix contained in '130-wpa_supplicant-multi_ap_roam.patch',
but in a different way:
nl80211_set_4addr_mode() could fail when trying to enable 4addr mode on
an interface that is in a bridge and has 4addr mode already enabled.
This operation would not have been necessary in the first place and this
failure results in disconnecting, e.g., when roaming from one backhaul
BSS to another BSS with Multi AP.
Avoid this issue by ignoring the nl80211 command failure in the case
where 4addr mode is being enabled while it has already been enabled.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
[bump PKG_RELEASE, more verbose commit description]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
After the ABI version rework, packages need to be declared in the order of
their dependencies, so that dependent packages will use the right ABI version
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Automatically setup dhcpv4 server just like it's done for dhcpv6.
To select whether odhcpd or dnsmasq are serving DHCPv4 requests there
still is the 'maindhcp' option. To make things less confusing, make
sure things really work out-of-the-box in case dnsmasq is not even
installed at the time the uci-defaults script is being run.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The removed patches were applied upstream.
This adapts ath10k-ct and mt76 to changed APIs.
nl80211.h in iw is updated to match the version from backports.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
5a2dd18 iwinfo: add hardware description for MediaTek MT7622
4a32b33 iwinfo: add PCI ID for MediaTek MT7613BE
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch is required to be able to roam from one backhaul AP to
another one in the same ESS.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(daniel@makrotopia.org: PKG_REVISION bump and refreshed patches)
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
This patch allows other applications to get events management
frames (for example: association requests).
This is useful in Multi-AP context to be able to save association
requests from stations.
It has been sent to upstream hostapd in this series:
https://patchwork.ozlabs.org/project/hostap/list/?series=217500
'700-wifi-reload.patch' is updated due to the introduction of
'110-notify-mgmt-frames.patch'.
Signed-off-by: Raphaël Mélotte <raphael.melotte@mind.be>
luci now uses ubus directly, so remove 'lucistat'.
For manual usage just print the ubus output, use luci for a pretty
version.
Signed-off-by: Andre Heider <a.heider@gmail.com>
luci now uses ubus directly, so remove 'lucistat'.
For manual usage just print the ubus output, use luci for a pretty
version.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Martin Schiller <ms@dev.tdt.de>
procd sends sigterm to stop daemons, hook it up.
This speeds up the shutdown sequence and gets rid of the following message:
daemon.info procd: Instance dsl_control::instance1 pid 15408 not stopped on SIGTERM, sending SIGKILL instead
Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Martin Schiller <ms@dev.tdt.de>
dnsmasq v2.84rc2 has been promoted to release.
No functional difference between v2.83test3 and v2.84/v2.84rc2
Backport 2 patches to fix the version reporting
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Use new ubus-based hotplug call in dhcp-script.sh
As sysntpd now makes use of the new ubus-based hotplug calls, dnsmasq
no longer needs to ship ACL to cover ntpd-hotplug.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Multiple sources are hosted on OpenWrts source server only. The source
URLs to point to the server vary based on different epochs in OpenWrts
history.
Replace all by @OPENWRT which is an "empty" mirror, therefore using the
fallback servers sources.cdn.openwrt.org and sources.openwrt.org.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Commit 7c8c4f1be6 ("hostapd: fix P2P group information processing
vulnerability") was missing the actual patch for the vulnerability.
Fixes: 7c8c4f1be6 ("hostapd: fix P2P group information processing vulnerability")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Use the latest stable kernel since the previous 5.8.x series is EOL.
Also drop the following patches recently accepted upstream:
* 001-libbpf-ensure-no-local-symbols-counted-in-ABI-check.patch
* 002-libbpf-fix-build-failure-from-uninitialized-variable.patch
* 003-bpftool-allow-passing-BPFTOOL_VERSION-to-make.patch
* 004-v5.9-bpftool-use-only-ftw-for-file-tree-parsing.patch
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
dnsmasq v2.83 has a bug in handling duplicate queries which means it may
try to reply using the incorrect network socket. This is especially
noticeable in dual stack environments where replies may be mis-directed to
IPv4 addresses on an IPv6 socket or IPv6 addresses on an IPv4 socket.
This results in system log spam such as:
dnsmasq[16020]: failed to send packet: Network unreachable
dnsmasq[16020]: failed to send packet: Address family not supported by protocol
dnsmasq v2.84test3 resolves these issues.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This is a helpful utility, but it does not have any dependencies
in this repository. Move it to packages feed.
The package does not seem to have a maintainer.
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Nick Hainke <vincent@systemli.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This is a helpful utility, but it does not have any dependencies
in this repository. Move it to packages feed.
Cc: Jo-Philipp Wich <jo@mein.io>
Cc: Nick Hainke <vincent@systemli.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The "cidr_contains6" functions clones the given cidr. The contains4
does not clone the cidr. Both functions do not behave the same.
I see no reason to push the cidr. I think that we get only a negligible
performance gain, but it makes ipv4 and ipv6 equal again.
Signed-off-by: Nick Hainke <vincent@systemli.org>
This fixes the following security problems in dnsmasq:
* CVE-2020-25681:
Dnsmasq versions before 2.83 is susceptible to a heap-based buffer
overflow in sort_rrset() when DNSSEC is used. This can allow a remote
attacker to write arbitrary data into target device's memory that can
lead to memory corruption and other unexpected behaviors on the target
device.
* CVE-2020-25682:
Dnsmasq versions before 2.83 is susceptible to buffer overflow in
extract_name() function due to missing length check, when DNSSEC is
enabled. This can allow a remote attacker to cause memory corruption
on the target device.
* CVE-2020-25683:
Dnsmasq version before 2.83 is susceptible to a heap-based buffer
overflow when DNSSEC is enabled. A remote attacker, who can create
valid DNS replies, could use this flaw to cause an overflow in a heap-
allocated memory. This flaw is caused by the lack of length checks in
rtc1035.c:extract_name(), which could be abused to make the code
execute memcpy() with a negative size in get_rdata() and cause a crash
in Dnsmasq, resulting in a Denial of Service.
* CVE-2020-25684:
A lack of proper address/port check implemented in Dnsmasq version <
2.83 reply_query function makes forging replies easier to an off-path
attacker.
* CVE-2020-25685:
A lack of query resource name (RRNAME) checks implemented in Dnsmasq's
versions before 2.83 reply_query function allows remote attackers to
spoof DNS traffic that can lead to DNS cache poisoning.
* CVE-2020-25686:
Multiple DNS query requests for the same resource name (RRNAME) by
Dnsmasq versions before 2.83 allows for remote attackers to spoof DNS
traffic, using a birthday attack (RFC 5452), that can lead to DNS
cache poisoning.
* CVE-2020-25687:
Dnsmasq versions before 2.83 is vulnerable to a heap-based buffer
overflow with large memcpy in sort_rrset() when DNSSEC is enabled. A
remote attacker, who can create valid DNS replies, could use this flaw
to cause an overflow in a heap-allocated memory. This flaw is caused
by the lack of length checks in rtc1035.c:extract_name(), which could
be abused to make the code execute memcpy() with a negative size in
sort_rrset() and cause a crash in dnsmasq, resulting in a Denial of
Service.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
53f07e9 ra: fix routing loop on point to point links
2b6959d ra: align ifindex resolving
Tested-by: Karl Vogel <karl.vogel@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
With encryption disabled, it was intended to set wpa_state=1 (enabled,
not configured) through the 'wps_not_configured' flag.
The flag is set appropriately but the condition using it is broken.
Instead, 'wps_configured' is checked and wpa_state is always 2 (enabled,
configured). Fix it by using the correct variable name.
Fixes: 498d84fc4e ("netifd: add wireless configuration support
and port mac80211 to the new framework")
Signed-off-by: Leon M. George <leon@georgemail.eu>
[commit title/message improvements]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The cidr_parse6 function parses a string to an ipv6-address.
The cidr struct contains a union called buf for the ipv4 and ipv6
address. Since it is a char pointer and the struct is initialized with
the maximum size (so ipv6 string) it does not make any difference.
However, we should access the buffer using the v6 name, since it could
be confusing otherwise.
Signed-off-by: Nick Hainke <vincent@systemli.org>
The key_mgmt variable was mistyped when checking against "WPS", so
the if clause was never entered.
Fixes: f5753aae23 ("hostapd: add support for WPS pushbutton station")
Signed-off-by: Leon M. George <leon@georgemail.eu>
[add commit message, bump PKG_RELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
'base' was never used.
Fixes: 498d84fc4e ("netifd: add wireless configuration support
and port mac80211 to the new framework")
Signed-off-by: Leon M. George <leon@georgemail.eu>
'enc_str' was never used.
Fixes: 498d84fc4e ("netifd: add wireless configuration support
and port mac80211 to the new framework")
Signed-off-by: Leon M. George <leon@georgemail.eu>
Granting capabilities CAP_NET_ADMIN and CAP_NET_RAW allows running
hostapd and wpa_supplicant without root priviledges.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This allows configuration of multicast_to_unicast and per_sta_vif options.
- multicast_to_unicast requests multicast-to-unicast conversion.
- per_sta_vif assigns each station its own AP_VLAN interface.
Signed-off-by: Etan Kissling <etan_kissling@apple.com>
Currently PHY information obtained from "iw phy" lacks information about
a PHYs HE capabilities when using the by default installed iw-tiny.
As there are already 802.11ax supported devices, enabled printing this
information for the by-default installed iw variant.
Signed-off-by: David Bauer <mail@david-bauer.net>
To simplify the way netifd acquires the PIDs of wpa_supplicant and
hostapd let the config_add method of both of them return the PID of the
called process. Use the returned PID instead of querying procd when
adding wpa_supplicant configuration.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
- Encode ABI version in compiled shared object file
- Only ship versioned shared library
a17f561 iwinfo: detect QCA IPQ4019 WiSoC from FDT
ea28dfb iwinfo: export ht and vht operation in scan results
4e22953 iwinfo: export center_chan info for local wifi
74d13fb cli: account for additional digit for frequencies above 10GHz
8bfd8d8 iwinfo: add support for GCMP cipher
618c1e8 iwinfo: add hardware description for QCA MIPS WiSoCs
0702f32 iwinfo: improve center channel handling
51c1336 iwinfo: set center chan unsupported for not-nl80211 driver
23d2722 build: add ability to specify shared object version
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This reverts commit f1620630e9.
This update introduces potentially remote exploitable buffer overreads
in IE parsing logic.
It also breaks the ABI without introdcing SOVERSION library versioning.
Furthermore, HT information is incorrectly added for non-HT BSSes.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
a17f561 iwinfo: detect QCA IPQ4019 WiSoC from FDT
ea28dfb iwinfo: export ht and vht operation in scan results
4e22953 iwinfo: export center_chan info for local wifi
74d13fb cli: account for additional digit for frequencies above 10GHz
8bfd8d8 iwinfo: add support for GCMP cipher
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This patch enables hostapd.sh to properly configure wpa_supplicant
for when GCMP is used as cipher in station mode.
Without this wpa_supplicant will be unable to connect to AP.
This is needed for wil6210 as it does not support CCMP.
Signed-off-by: Robert Marko <robimarko@gmail.com>
This adds an option "hostapd_bss_options" that does the same as
"hostapd_options" but on a per-BSS level, instead of a per-device level.
This can be used, for example, to configure different per-devce sae_passwords
per BSS or to augment some of the existing per-BSS options.
Signed-off-by: Florian Beverborg <flo@beverb.org>
[remove whitespace errors, bump release]
Signed-off-by: Paul Spooren <mail@aparcar.org>
This patch was already applied upstream and not needed here.
Fixes: 06403981e1 ("ppp: update to version 2.4.7.git-2019-05-06")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
By setting 'auto', the zero address or the empty string as source
address (option ipaddr, option ip6addr), vxlan will choose one
dynamically. This helps in setups where a wan ip or prefix changes.
This corresponse to setting up an vxlan tunnel with:
proto vxlan6:
# ip link add vx0 type vxlan id ID local :: ...
proto vxlan:
# ip link add vx0 type vxlan id ID local 0.0.0.0 ...
While it is possible to not specify a source ip at all, the kernel will
default to setting up a ipv4 tunnel. The kernel will take any hint from
source and peer ips to figure out, what tunnel type to use. To make sure
we setup an ipv6 tunnel for proto vxlan6, this workaround is needed.
This will not change the behaviour of currently working configurations.
However this will allow former broken configurations, namely those not
specifying both a source address and tunnel interface, to setup a
tunnel interface. Previously those configurations weren't reporting an
error and were stueck in a setup loop like in Bug FS#3426.
This change lifts the currently very strict behaviour and should fix the
following bug:
Fixes: FS#3426
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3426
Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
b75bcad dhcpv6-ia: remove assignment equal to 0 checks
d1ae052 dhcpv6-ia: fix logic to include IA_PD prefix with lifetimes set to 0
9d5e379 dhcpv6-ia: fix prefix delegation behavior
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
As of hostapd upstream commit 7d2ed8ba "Remove CONFIG_IEEE80211W build parameter"
https://w1.fi/cgit/hostap/commit?id=7d2ed8bae86a31dd2df45c24b3f7281d55315482
802.11w feature is always enabled in the build time.
It doesn't make sense to opt-in 802.11w per driver as hostapd will always
be compiled with this feature enabled.
As suggested by Hauke Mehrtens, for now keep 11w enabled in build_features.h
for compatibility reasons. This option will be dropped when LuCI is adjusted.
Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
When hostapd gets restarted to often/quickly will cause procd to not restart it
anymore. it will think that hapd is in a crash loop.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name> [adjust respawn time]
Currently, EAPOLv2 (802.1X-2004) is used by default for legacy clients that
are not WPA2 (RSN) capable. These legacy clients are often intolerant to this
EAPOL version and fail to connect.
hostapd.conf upstream documents for eapol_version the following and that this
is a known compatibility issue with version 2:
// IEEE 802.1X/EAPOL version
// hostapd is implemented based on IEEE Std 802.1X-2004 which defines EAPOL
// version 2. However, there are many client implementations that do not handle
// the new version number correctly (they seem to drop the frames completely).
// In order to make hostapd interoperate with these clients, the version number
// can be set to the older version (1) with this configuration value.
// Note: When using MACsec, eapol_version shall be set to 3, which is
// defined in IEEE Std 802.1X-2010.
//eapol_version=2
For the wpa parameter, hostapd.conf upstream documents that this is a bitfield,
configured as follows:
// Enable WPA. Setting this variable configures the AP to require WPA (either
// WPA-PSK or WPA-RADIUS/EAP based on other configuration). For WPA-PSK, either
// wpa_psk or wpa_passphrase must be set and wpa_key_mgmt must include WPA-PSK.
// Instead of wpa_psk / wpa_passphrase, wpa_psk_radius might suffice.
// For WPA-RADIUS/EAP, ieee8021x must be set (but without dynamic WEP keys),
// RADIUS authentication server must be configured, and WPA-EAP must be included
// in wpa_key_mgmt.
// This field is a bit field that can be used to enable WPA (IEEE 802.11i/D3.0)
// and/or WPA2 (full IEEE 802.11i/RSN):
// bit0 = WPA
// bit1 = IEEE 802.11i/RSN (WPA2) (dot11RSNAEnabled)
// Note that WPA3 is also configured with bit1 since it uses RSN just like WPA2.
// In other words, for WPA3, wpa=2 is used the configuration (and
// wpa_key_mgmt=SAE for WPA3-Personal instead of wpa_key_mgmt=WPA-PSK).
//wpa=2
For client compatibility therefore:
EAPOLv1 (802.1X-2001) should be used by default where WPA is enabled.
EAPOLv2 (802.1X-2004) should be used by default where WPA is disabled.
To fix this, we can therefore change in the script:
set_default eapol_version 0
To the following:
set_default eapol_version $((wpa & 1))
This therefore:
1) Sets eapol_version to 1 where WPA has been enabled via wpa bit0 being set.
2) Sets eapol_version to 0 where WPA has been disabled via wpa bit0 being unset.
For usual configurations that only have WPA2 enabled, EAPOLv2 is then used.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
The patch removes a libpcap check to avoid a problem with libpcap. Fix
libpcap instead.
Modernize Makefile:
Use a normal autoconf bool instead of checking for CONFIG_IPV6.
Remove old configure and MAKE_FLAGS hacks. Removing them results in
compilation continuing to work without a problem.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
hostapd.sh does not parse skip_inactivity_poll boolean from
/etc/config/wireless despite being mentioned in the documentation [1].
This change fixes this, and by default sets its value to 0 [1].
[1] https://openwrt.org/docs/guide-user/network/wifi/basic
Signed-off-by: Nadim Atiya <nadim.atiya@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[fix and reformat commit message, make patch apply]
So we can ship px5g-wolfssl by default in the release image, but still
make the HTTPS for LuCI optional. This small change with addition of
`CONFIG_PACKAGE_px5g-wolfssl=y` into the buildbot's seed config for the
next release should provide optional HTTPS in the next release.
Disabling the current default automatic uhttpd's redirect to HTTPS
should make the HTTPS optional. That's it, user would either need to
switch to HTTPS by manually switching to https:// protocol in the URL or
by issuing the following commands to make the HTTPS automatic redirect
permanent:
$ uci set uhttpd.main.redirect_https=1
$ uci commit uhttpd
$ service uhttpd reload
Signed-off-by: Petr Štetiar <ynezz@true.cz>
You shouldn't need the overhead of GRE just to add multicast
capability on a point-to-point interface (for instance, you might
want to run mDNS over IPsec transport connections, and Avahi
requires IFF_MULTICAST be set on interfaces, even point-to-point
ones).
Borrowed heavily from:
b3c9321b9e gre: Support multicast configurable gre interfaces
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Bump package version after previous changes.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
[added missing commit description]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
binary size cost is much less than 1k.
tested on ath79/generic:
bin: 215128 -> 215132 (+4b)
ipk: 111183 -> 111494 (+311b)
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
this commit removes manual recipes for options and introduces mapping lists:
- DB_OPT_COMMON holds option mappings which are common for all builds;
- DB_OPT_CONFIG holds option mappings which are depend on config settings.
DB_OPT_COMMON is space-separated list of 'words', each of them is in format:
'header_option|value'
'header_option' is added with value 'value' to 'localoptions.h'.
if 'header_option' is preceded by two exclamation marks ('!!')
then option is not added to 'localoptions.h' but replaced in 'sysoptions.h'.
in short:
option|value - add option to localoptions.h
!!option|value - replace option in sysoptions.h
DB_OPT_CONFIG is space-separated list of 'words', each of them is in format:
'header_option|config_variable|value_enabled|value_disabled'
'header_option' is handled likewise in DB_OPT_COMMON.
if 'config_variable' is enabled (technically: not disabled)
then 'header_option' is set to 'value_enabled' and 'value_disabled' otherwise.
in short:
option|config|enabled|disabled = add option to localoptions.h
!!option|config|enabled|disabled = replace option in sysoptions.h
option := (config) ? enabled : disabled
If you're not sure that option's value doesn't have '|' within - add your recipe
manually right after '$(Build/Configure/dropbear_headers)' and write some words
about your decision.
PS about two exclamation marks:
early idea was to use one exclamation mark to denote such header options
but then i thought single exclamation mark may be overlooked by mistake.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
- add two helper functions to avoid mistakes with
choice of correct header file to work with
- update rules accordingly
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
put static options at first place, then place configurable options.
also put DROPBEAR_ECC right before DROPBEAR_ECC_FULL to ease maintainance.
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
this option was disabled in 2011 and these long nine years showed us that change was definitely wrong.
binary size cost is much less than 1k.
tested on ath79/generic:
bin: 215128 -> 215128 (no change)
ipk: 111108 -> 111183 (+75b)
Fixes: 3c801b3dc0 ("tune some more options by default to decrease size")
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
The package has no reason to be in openwrt.git. Move it to packages.git.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Acked-by: Jo-Philipp Wich <jo@mein.io>
The lldpd sources ship a modified local AX_LIB_READLINE M4 macro which
conflicts with the official macro shipped by autoconf-archive.
Due to the official macro having the same name and a higher serial
number, autoconf will prefer including that one instead of the local
copy, preventing the substitution of @READLINE_LIBS@ in Makefile.in
templates, ultimately leading to the following build failure when
linking lldpcli:
...-gcc: error: READLINE_LIBS@: No such file or directory
Avoid this problem by renaming the locally shipped macro to not clash
with the official implementation anymore.
Ref: https://github.com/lldpd/lldpd/pull/423
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Tested-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Set legacy_rates to 0 by default to disable 802.11b data rates by default.
The time has long come where 802.11b DSSS/CCK data rates should be disabled
by default in OpenWRT. Users in need of 802.11b client support can reasonably
enable these where they are needed.
The balance of equities has significantly, and for a long time, tipped
such that dropping backwards compatibility by default with 802.11b
devices is appropriate, proportionate and justified. By doing so,
management and control traffic is moved by default to a 20
MHz wide 6 Mb/s OFDM data rate instead of a 22 MHz wide 1 Mb/s DSSS data
rate. This is significantly more airtime efficient.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
faed29a dhcpv6: only refresh timers when reconfigure is valid
9c50975 dhcpv6: fix printing identity association id
a7b2221 dhcpv6: avoid sending continuous renew/rebind messages
d7afa2b dhcpv6: add extra syslog info traces
f5728e4 odhcp6c_find_entry: exclude priority from the list of fields that must match
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
d6bd1047d004 vlandev: dump vlan id in device status
e0c838bd06a6 vlandev: support bridge-vlan aliases in the vid config parameter
574dc4a17105 system-dummy: print configured mac address
14f0e8ff928f system-linux: simplify mask check in system_if_apply_settings
524310276f20 system-linux: move device settings handling to device.c
42c48866f1c1 config: parse default mac address from board.json
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This should fix an issue when user have a router with enabled seccomp
and tries to run umdns package which was build with SDK with disabled
seccomp support.
Signed-off-by: Jan Pavlinec <jan.pavlinec@nic.cz>
Add a cell_density option to configure data rates for normal, high and
very high cell density wireless deployments.
The purpose of using a minimum basic/mandatory data rate that is higher
than 6 Mb/s, or 5.5 Mb/s (802.11b compatible), in high cell density
environments is to transmit broadcast/multicast data frames using less
airtime or to reduce management overheads where significant co-channel
interference (CCI) exists and cannot be avoided.
Caution: Without careful design and validation, configuration of a too
high minimum basic/mandatory data rate can sacrifice connection stability
or disrupt the ability to reliably connect and authenticate for little to
no capacity benefit. This is because this configuration affects the
ability of clients to hear and demodulate management, control and
broadcast/multicast data frames.
Deployments that have not been specifically designed and validated are
usually best suited to use 6, 12 and 24 Mb/s as basic/mandatory data
rates.
Only usually seek to configure a 12 Mb/s, or 11 Mb/s (802.11b
compatible), minimum basic/mandatory rate in high cell density
deployments that have been designed and validated for this.
For many deployments, the minimum basic/mandatory data rate should not be
configured above 12 Mb/s to 18 Mb/s, 24 Mb/s or higher. Such a
configuration is only appropriate for use in very high cell density
deployment scenarios.
A cell_density of Very High (3) should only be used where a deployment
has a valid use case and has been designed and validated specifically for
this use, nearly always with highly directional antennas - an example
would be stadium deployments. For example, with a 24 Mb/s OFDM minimum
basic/mandatory data rate, approximately a -73 dBm RSSI is required to
decode frames. Many clients will not have roamed elsewhere by the time
that they experience -73 dBm and, where they do, they frequently may not
hear and be able to demodulate beacon, control or broadcast/multicast
data frames causing connectivity issues.
There is a myth that disabling lower basic/mandatory data rates will
improve roaming and avoid sticky clients. For 802.11n, 802.11ac and
802.11ax clients this is not correct as clients will shift to and use
lower MCS rates and not to the 802.11b or 802.11g/802.11a rates that are
able to be used as basic/mandatory data rates.
There is a myth that disabling lower basic/mandatory data rates will
ensure that clients only use higher data rates and that better
performance is assured. For 802.11n, 802.11ac and 802.11ax clients this
is not correct as clients will shift around and use MCS rates and not the
802.11b or 802.11g/802.11a rates that able to be used as basic/mandatory
data rates.
Cell Density
0 - Disabled (Default)
Setting cell_density to 0 does not configure data rates. This is the
default.
1 - Normal Cell Density
Setting cell_density to 1 configures the basic/mandatory rates to 6, 12
and 24 Mb/s OFDM rates where legacy_rates is 0. Supported rates lower
than the minimum basic/mandatory rate are not offered.
Setting cell_density to 1 configures the basic/mandatory rates to the 5.5
and 11 Mb/s DSSS rates where legacy_rates is 1. Supported rates lower
than the minimum basic/mandatory rate are not offered.
2 - High Cell Density
Setting the cell_density to 2 configures the basic/mandatory rates to the
12 and 24 Mb/s OFDM rates where legacy_rates is 0. Supported rates lower
than the minimum basic/mandatory rate are not offered.
Setting the cell_density to 2 configures the basic/mandatory rates to the
11 Mb/s DSSS rate where legacy_rates is 1. Supported rates lower than the
minimum basic/mandatory rate are not offered.
3 - Very High Cell Density
Setting the cell_density to 3 configures the basic/mandatory rates to the
24 Mb/s OFDM rate where legacy_rates is 0. Supported rates lower than the
minimum basic/mandatory rate are not offered.
Setting the cell_density to 3 only has effect where legacy_rates is 0,
else this has the same effect as being configured with a cell_density of 2.
Where specified, the basic_rate and supported_rates options continue to
override both the cell_density and legacy_rates options.
Signed-off-by: Nick Lowe <nick.lowe@gmail.com>
Several variables in hostapd.sh can be used uninitialized in numerical
comparisons, causing errors in logread:
netifd: radio24 (1668): sh: out of range
Set defaults for those variables to silence those errors.
Fixes: b518f07d4b ("hostapd: remove ieee80211v option")
Fixes: cc80cf53c5 ("hostapd: add FTM responder support")
Fixes: e66bd0eb04 ("hostapd: make rrm report independent of ieee80211k setting")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
This PR backports upstream fix for CVE-2020-8037. This fix is only
relevant for tcpdump package, tcpdump-mini is not affeted by this issue.
Signed-off-by: Jan Pavlinec <jan.pavlinec@nic.cz>
[added missing commit description]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Setting the plmn to '0' (auto) will implicitly lead to a (delayed)
network re-registration, which could further lead to some timing
related issues in the qmi proto handler.
On the other hand, if you switch back from manual plmn selection
to auto mode you have to set it to '0', because this setting is
permanently "saved" in the wwan module.
Conclusion:
If plmn is configured, check if it's already set euqally in the module.
If so, do nothing. Otherwise set it.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixes the offset of the patch added in 93bbd998aa
("hostapd: enter DFS state if no available channel is found").
Signed-off-by: Leon M. George <leon@georgemail.eu>
213748a9bcd9 system-linux: implement full device present state management for force-external devices
3abe1fc87151 system-linux: add retry for adding member devices to a bridge
Signed-off-by: Felix Fietkau <nbd@nbd.name>
There already was an option for autoconfiguring IPv4 from QMI but this
was removed by commit 3b9b963e6e ("uqmi: always use DHCP for IPv4").
DHCP does not work on MR400 LTE module (in TL-MR6400 v4) so let's readd
support for IPv4 autoconf from QMI but this time allow to configure this
for IPv4 and IPv6 independently and keep DHCP default on IPv4.
Signed-off-by: Filip Moc <lede@moc6.cz>
Give possibility to wait forever the registration by setting timeout
option to 0.
No timeout can be useful if the interface starts whereas no network is
available, because at the end of timeout the interface will be stopped
and never restarted.
Signed-off-by: Thomas Richard <thomas.richard@kontron.com>
351d690f1a09 wireless: fix passing bridge name for vlan hotplug pass-through
c1c2728946b5 config: initialize bridge and bridge vlans before other devices
5e18d5b9ccb1 interface: do not force link-ext hotplug interfaces to present by default
4544f026bb09 bridge-vlan: add support for defining aliases for vlan ids
Signed-off-by: Felix Fietkau <nbd@nbd.name>
No special changes, just get in sync with recent code.
See here for the changelog:
http://software.es.net/iperf/news.html#iperf-3-9-released
The ipkg sizes changes as follows for mips 24kc :
3.7 : iperf3_3.7-1_mips_24kc.ipk 39675
3.9 : iperf3_3.9-1_mips_24kc.ipk 41586
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This sets the validity interval for the BSS transition candidate
list to the same value as the disassociation timer.
Currently the value is always 0, which is the specification states is a
reserved value. Also, wpa_supplicant and from the looks of it some
Android implementations will outright ignore the candidate list in this
case.
Signed-off-by: David Bauer <mail@david-bauer.net>
* Add support for passing airtime_sta_weight into hostapd configuration.
* Since that commit it is possible to configure station weights. Set higher
value for larger airtime share, lower for smaller share.
I have tested this functionality by modyfing /etc/config/wireless to:
config wifi-device 'radio0'
...
option airtime_mode '1'
config wifi-iface 'default_radio0'
...
list airtime_sta_weight '01:02:03:04:05:06 1024'
Now, when the station associates with the access point it has been assigned
a higher weight value.
root@OpenWrt:~# cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/stations/01\:02\:03\:04\:05\:06/airtime
RX: 12656 us
TX: 10617 us
Weight: 1024
Deficit: VO: -2075 us VI: 256 us BE: -206 us BK: 256 us
[MAC address has been changed into a dummy one.]
Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
airtime_mode is always parsed as an empty string since it hasn't been
added into hostapd_common_add_device_config function.
Fixes: e289f183 ("hostapd: add support for per-BSS airtime configuration")
Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
This adds a new get_status method to a hostapd interface, which
provides information about the current interface status.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds information from mac80211 to hostapd get_client ubus function.
This way, TX as well as RX status information as well as the signal can
be determined.
Signed-off-by: David Bauer <mail@david-bauer.net>
procd-seccomp switched to OCI-compliant seccomp parser instead of our
(legacy, OpenWrt-specific) format. Convert ruleset to new format.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
wireguard-tools is trying to import the menuconfig section
from the wireguard package, but since it's not anymore in
the same makefile this seems to fail and wireguard-tools
ends up in "extra packages" category instead with other
odds and ends.
Same for the description, it's trying to import it from the
wireguard package but it fails so it only shows the line
written in this makefile.
remove the broken imports and add manually the entries
and description they were supposed to load
Fixes: ea980fb9c6 ("wireguard: bump to 20191226")
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
[fix trailing whitespaces, add Fixes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Update dropbear to latest stable 2.81; for the changes see https://matt.ucc.asn.au/dropbear/CHANGES
Refresh patches
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
BusyBox ip already provides the required functionality and is enabled by default
in OpenWrt. This patch drops the ip dependency and makes the BusyBox ip required
dependencies explicit, allowing for a significant image size reduction.
openwrt-ath79-generic-ubnt_nanostation-loco-m-squashfs-sysupgrade.bin size:
4588354 bytes (with ip-tiny)
4457282 bytes (with BusyBox ip)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Update iproute2 to latest stable 5.9; for the changes see https://lwn.net/Articles/834755/
Refresh patches
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Acked-by: Hauke Mehrtens <hauke@huake-m.de>
* noise: take lock when removing handshake entry from table
This is a defense in depth patch backported from upstream to account for any
future issues with list node lifecycles.
* netns: check that route_me_harder packets use the right sk
A test for an issue that goes back to before Linux's git history began. I've
fixed this upstream, but it doesn't look possible to put it into the compat
layer, as it's a core networking problem. But we still test for it in the
netns test and warn on broken kernels.
* qemu: drop build support for rhel 8.2
We now test 8.3+.
* compat: SYM_FUNC_{START,END} were backported to 5.4
* qemu: bump default testing version
The real motivation for this version bump: 5.4.76 made a change that broke our
compat layer.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
3023b0cc7352 bridge: add support for defining port member vlans via hotplug ops
a3016c451248 vlan: add pass-through hotplug ops that pass the VLAN info to the bridge
d59f3ddcbaf0 vlandev: add pass-through hotplug ops that pass the VLAN info to the bridge
dd5e61153636 bridge: show vlans in device status
a56e14afa612 bridge: preserve hotplug ports on vlan update if config is unchanged
d1e8884f8911 bridge: fix use-after-free bug on bridge member free
3a2b21001c3c system-dummy: set present state only for simple devices
ed11f0c0ffe4 bridge: only overwrite implicit vlan assignment if vlans are configured
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Allow configuring ipsets with dedicated config sections:
config ipset
list name 'ss_rules_dst_forward'
list name 'ss_rules6_dst_forward'
list domain 't.me'
list domain 'telegram.org'
instead of current, rather inconvenient syntax:
config dnsmasq
...
list ipset '/t.me/telegram.org/ss_rules_dst_forward,ss_rules6_dst_forward'
Current syntax will still continue to work though.
With this change, a LuCI GUI for DNS ipsets should be easy to implement.
Signed-off-by: Aleksandr Mezin <mezin.alexander@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
The uhttpd package takes care of creating self-signed certificates if
px5g is installed. This improves the security of router management as it
encrypts the LuCI connection.
The EC P-256 curve is faster than RSA which which improves the user
experience on embedded devices. EC P-256 is support for as old devices
as Android 4.4.
Signed-off-by: Paul Spooren <mail@aparcar.org>
If only AP mode is needed, this is currently the most space-efficient way to
provide support for WPA{2,3}-PSK, 802.11w and 802.11r.
openwrt-ath79-generic-ubnt_nanostation-loco-m-squashfs-sysupgrade.bin sizes:
4719426 bytes (with wpad-basic-wolfssl)
4457282 bytes (with hostapd-basic-wolfssl)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Hotspot 2.0 AP features have been made available in the -full variants
of hostapd and wpad. Hence we no longer need a seperate package for
that.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add OpenSSL-linked basic variants (which provides WPA-PSK only, 802.11r and
802.11w) of both hostapd and wpad. For people who don't need the full hostapd
but are stuck with libopenssl for other reasons, this saves space by avoiding
the need of an additional library (or a larger hostapd with built-in crypto).
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This adds missing config symbols for interworking as well as Hotspot 2.0
to the wpa_supplicant-full configuration.
These symbols were added to the hostapd-full configuration prior to this
commit. Without adding them to the wpa_supplicant configuration,
building of wpad-full fails.
Thanks to Rene for reaching out on IRC.
Fixes: commit be9694aaa2 ("hostapd: add UCI support for Hotspot 2.0")
Fixes: commit 838b412cb5 ("hostapd: add interworking support")
Signed-off-by: David Bauer <mail@david-bauer.net>
/etc/hotplug.d/ntp/25-dnsmasqsec is being sourced by /sbin/hotplug-call
running as ntpd user. For that to work the file needs to be readable by
that user.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds configuration options to enable interworking for hostapd.
All options require iw_enabled to be set to 1 for a given VAP.
All IEEE802.11u related settings are supported with exception of the
venue information which will be added as separate UCI sections at a
later point.
The options use the same name as the ones from the hostapd.conf file
with a "iw_" prefix added.
All UCI configuration options are passed without further modifications
to hostapd with exceptions of the following options, whose elements can
be provided using UCI lis elements:
- iw_roaming_consortium
- iw_anqp_elem
- iw_nai_realm
- iw_domain_name
- iw_anqp_3gpp_cell_net
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds support for enabling the FTM responder flag for the APs
extended capabilities. On supported hardware, enabling the ftm_responder
config key for a given AP will enable the FTM responder bit.
FTM support itself is unconditionally implemented in the devices
firmware (ath10k 2nd generation with 3.2.1.1 firmware). There's
currently no softmac implementation.
Also allow to configure LCI and civic location information which can be
transmitted to a FTM initiator.
Signed-off-by: David Bauer <mail@david-bauer.net>
Remove the ieee80211v option. It previously was required to be enabled
in order to use time_advertisement, time_zone, wnm_sleep_mode and
bss_transition, however it didn't enable any of these options by default.
Remove it, as configuring these options independently is enough.
This change does not influence the behavior of any already configured
setting.
Signed-off-by: David Bauer <mail@david-bauer.net>
Allow to configure both RRM beacon as well as neighbor reports
independently and only enable them by default in case the ieee80211k
config option is set.
Signed-off-by: David Bauer <mail@david-bauer.net>
59e4fc98162d cache: cache_answer: fix off by one
4cece9cc7db4 cache: cache_record_find: fix buffer overflow
be687257ee0b cmake: tests: provide umdns-san binary
bf01f2dd0089 tests: add dns_handle_packet_file tool
134afc728846 tests: add libFuzzer based fuzzing
de08a2c71ca8 cmake: create static library
cdc18fbb3ea8 interface: fix possible null pointer dereference
1fa034c65cb6 interface: fix value stored to 'fd' is never read
3a67ebe3fc66 Add initial GitLab CI support
50caea125517 cmake: fix include dirs and libs lookup
Signed-off-by: Petr Štetiar <ynezz@true.cz>
For IPv6 native connections when using IPv6 DNS lookups, there is no
valid default resolver if ignoring WAN DHCP provided nameservers.
This uses a runtime check to determine if IPv6 is supported on the host.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
ntpd in packages feed had already a user 'ntp' with UID 123 declared.
Rename the username of busybox-ntpd to be 'ntp' instead of 'ntpd' so
it doesn't clash.
Reported-by: Etienne Champetier <champetier.etienne@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Changelog follows
ced0d535 build: find and use libnl header dirs
5722218e proto: rework parse_addr to return struct device_addr
3d7bf604 device_addr: record address index as in the blob
24ce1eab interface: proto_ip: order by address index first
This bump mainly affects order of interface addresses in ubus output. At the
moment dnsmasq uses first address of an interface for setting dhcp-range option
in its config
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Expose WPS ubus API only if compiled with WPS support and add new
handler for wps_status call.
Also add '-v wps' option to check whether WPS support is present in
hostapd.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is useful to bring up multiple client mode interfaces on a single
channel much faster without having to scan through a lot of channels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It should return false to indicate that the option should not be ignored
Fixes 064dc1e8 ("dnsmasq: abort when dnssec requested but not
available")
Reported-by: Sami Olmari <sami@olmari.fi>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The TFTP server provided by dnsmasq supports serving a select boot image
based on the client's MAC or IP address. This allows an administrator
to activate this feature in /etc/config/dhcp. Here is an example
/etc/config/dhcp that configures dnsmasq with --tftp-unique-root=mac:
...
config dnsmasq
option enable_tftp 1
option tftp_root /usr/libexec/tftpboot
option tftp_unique_root mac
config boot router
option serveraddress 192.168.1.1
option servername tftp.example.com
option filename openwrt-initramfs-kernel.bin
...
With this configuration, dnsmasq will serve
/usr/libexec/tftpboot/00-11-22-33-44-55/openwrt-initramfs-kernel.bin to
the client with MAC address 00:11:22:33:44:55.
Signed-off-by: W. Michael Petullo <mike@flyn.org>
Add config options:
srcportmin/srcportmax : range of port numbers to use as UDP source ports
to communicate to the remote VXLAN tunnel endpoint
ageing : lifetime in seconds of FDB entries learnt by the kernel
maxaddress : maximum number of FDB entries
learning : enable/disable entering unknown source link layer addresses
and IP addresses into the VXLAN device FDB.
rsc : enable/disable route short circuit
proxy : enable/disable ARP proxy
l2miss : enable/disable netlink LLADDR miss notifications
l3miss : enable/disable netlink IP ADDR miss notifications
gbp : enable/disable the Group Policy extension
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Make the BSSID and SSID fields optional when configuring a neighbor
report into hostapd.
Both options can now be an empty string. For the BSSID, the first 6 byte
are copied from the neighbor report. For the SSID, the SSID for the
affected hostapd BSS is used.
Signed-off-by: David Bauer <mail@david-bauer.net>
Rafal Milecki pointed out that ubus events are meant for low-level ubus
events only (e.g. addition or removal of an object). Higher level
events should happen as notifications on the ubus object itself.
Dispatch BSS events on the main hostapd ubus object instead of
publishing them as ubus events.
Signed-off-by: David Bauer <mail@david-bauer.net>
hostapd will emit a ubus event with the eventname hostapd.<ifname>.<event>
when adding, removing or reloading a BSS.
This way, services which install state (for example the RMM neighbor
list) can on-demand reinstall this information for the BSS without
polling this state.
Signed-off-by: David Bauer <mail@david-bauer.net>
UCI defaults scripts are supposed to be numbered, but odhcpd's lacked numbering, which
turned out to mess up my custom scripts numbered 9[0-9]_*. The idea is to have high number
(custom) scripts executed last. Jow confirmed numbering is the default case, not the
exception (thanks).
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
With global NLS support enabled (CONFIG_BUILD_NLS), the linked libelf.so
and libbfd.so libraries will depend on libintl.so. Import the nls.mk helper
to set library prefixes and flags accordingly, and also conditionally add
"-lintl" as link-time library.
Fix a build error on ppc due to a EDEADLOCK redefinition in errno.h.
Use upstream stable kernel 5.8.9, and fix overriding of feature detection
to only allow/hide detected features. Also refresh existing patches.
Fixes: 2f0d672088 ("bpftools: add utility and library packages supporting
eBPF usage")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add support for per-BSS airtime weight configuration. This allows to set
a airtime weight per BSS as well as a ratio limit based on the weight.
Support for this feature is only enabled in the full flavors of hostapd.
Consult the hostapd.conf documentation (Airtime policy configuration)
for more information on the inner workings of the exposed settings.
Signed-off-by: David Bauer <mail@david-bauer.net>
* ipc: split into separate files per-platform
This is in preparation for FreeBSD support, which I had hoped to have this
release, but we're still waiting on some tooling fixes, so hopefully next
wg(8) will support that. Either way, the code base is now a lot more amenable
to adding more kernel platform support.
* man: wg-quick: use syncconf instead of addconf for strip example
Simple documentation fix.
* pubkey: isblank is a subset of isspace
* ctype: use non-locale-specific ctype.h
In addition to ensuring that isalpha() and such isn't locale-specific, we also
make these constant time, even though we're never distinguishing between bits
of a secret using them. From that perspective, though, this is markedly better
than the locale-specific table lookups in glibc, even though base64 characters
span two cache lines and valid private keys must hit both. This may be useful
for other projects too: https://git.zx2c4.com/wireguard-tools/tree/src/ctype.h
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Don't use bash syntax, because /bin/sh is used here.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[bump PKG_RELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* compat: backport kfree_sensitive and switch to it
* netlink: consistently use NLA_POLICY_EXACT_LEN()
* netlink: consistently use NLA_POLICY_MIN_LEN()
* compat: backport NLA policy macros
Backports from upstream changes.
* peerlookup: take lock before checking hash in replace operation
A fix for a race condition caught by syzkaller.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
