Let's use /etc/sysctl.d for package-provided snippets and leave
/etc/sysctl.conf to the admin. Don't backup /etc/sysctl.d on upgrades, so
old defaults get replaced properly.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
We can use /etc/sysctl.d/* for package-supplied sysctl snippets, giving
admins the option to use /etc/sysctl.conf to override settings.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
11_migrate-sysctl has not been updated with new file hashes since 2012.
Let's get rid of it.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some packages are already using $(1)/var on package install.
On multiuser systems this breaks the build when multiple
users build OpenWrt.
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
It's intentional that some boards within a target don't have all LEDs
which are tried to be setup in a common script. Don't show a warning in
such cases.
Fixes: 4f4fc993db ("base-files: add more name source to get_dt_led helper function")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Not all LED driver are using the label devicetree property for the led
name. Add support for the TI/National Semiconductor LP55xx Led Drivers,
which are using the chan-name property for the led name, as fallback.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add a fucntion to get the a binary mac address from file. Use the new
function for mtd_get_mac_binary() to limit duplicate code.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The default fragment low/high thresholds are 3 and 4 MB. On devices with
only 32MB RAM, these settings may lead to OOM when many fragments that
cannot be reassembled are received. Decrease fragment low/high thresholds
to 384 and 512 kB on devices with less than 64 MB RAM.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Many packages use the opkg conffiles field to list configuration files that
are to be retained on upgrades. Make this work on systems without opkg.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
There was a mismatch between indicating factory reset and code actually
starting it. After 5 seconds status LED started blinking rapidly letting
user know it's ready to release reset button. In practice button had to
stay pressed for another second in order to relly start the process.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Current code and also before commit da52dd0c83 was vulnerable to shell
injection using volume lables in the GPT partition table of block
devices. Given that partition names can be freely defined in GPT tables
we really shouldn't evaluate a string which is potentially crafted with
evil intentions. Hence rather use `export -n` to absorb the uevent's
variables into the environment.
Fixes commit da52dd0c83 (base-files: quote values when evaluating uevent)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[mschiffer@universe-factory.net: suggested export -n usage]
When sourcing /sys/class/block/*/uevent values have to be quoted as
they may contain spaces (e.g. in PARTNAME).
Fix this by pre-processing with sed before sourcing.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
We don't need two versions of this. The escaping quotes
is so that the sed commands aren't misinterpreted by shell;
it has nothing to do with the contents of the file, thus
one version is adequate.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Obviously not all GPIO controller allow to change the direction. The issue
is around since the beginning of the script but only due to the recent
changes error messages are more visible.
Add a check if a change of the direction is supported by the GPIO
controller and fallback to setting only the value if not.
Fixes: FS#1271
Signed-off-by: Mathias Kresin <dev@kresin.me>
GPIOs are exported as active high to the sysfs, hence the logic need to be
inverted.
Fixes: e66c47fb14 ("base-files: gpio switch: set output value with
direction")
Signed-off-by: Mathias Kresin <dev@kresin.me>
Commit 30f61a34b4 claimed to drop -d & -p
options. In reality only -d was dropped. Update command help text to
reflect that -d is no longer a supported option.
Fixes FS#1187
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Add the uci option nameprefix to specifc a target netdev name. Patch the
br2684ctl code to accept and set a netdev name via commandline parameters.
It allows to use the same netdev name for ATM and PTM lines on lantiq
xdsl hardware.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Mathis Kresin <dev@kresin.me>
Use the "low" and "high" values to configure the GPIO as an output with
that initial value. It ensures that the gpio doesn't have a unwanted value
during the time the direction is set to ouput and the actual value is
applied.
We don't need to take care of the GPIO polarity for now, since our
exported GPIOs are always active low.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Start gpio_switch before the boot state is set to up/initialised/done.
This way the exported GPIOs are available at the time rc.local is started.
Signed-off-by: Mathias Kresin <dev@kresin.me>
In current state, if there is START but no STOP, enbale()
will return 1 (failure), which is wrong.
Moreover there is no need to check for START/STOP twice.
Instead, add err variable to save success state and
and return it's value.
Also eliminate the need to disable() by using 'ln -sf',
which will first delete the old symlink if one exists.
Changes from v1:
- fixed description
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fixes: 8170f280c4 ("base-files: set FAILSAFE in /etc/profile when
/tmp/.failsafe exists")
Since dropbear clears the environment, FAILSAFE was not set as intended in
failsafe mode. This also broke sysupgrade from failsafe mode over SSH.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Since /overlay/upper appeared, -b ignored -c silently (cause it was
still checking for /overlay/etc). Now, if /overlay/upper is absent,
sysupgrade -c will fail and exit verbosely.
Fix -l to consider -c (it never did).
Clean up to always use /overlay/upper/xxx instead of still checking
for /overlay/xxx.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Lantiq and IPQ806X (which includes IPQ40XX) both define the
same custom function {ipq806x|lantiq}_get_dt_led.
This patch moves the function into the base-file package at
lib/functions/leds.sh to make it more accessible for other
targets as well.
Cc: Mathias Kresin <dev@kresin.me>
Cc: John Crispin <john@phrozen.org>
Cc: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
To not clutter the system when building an opkg free image, generate the
distfeeds.conf only if CLEAN_IPKG is unset.
Since opkg is now a shared package, we can't rely on PACKAGE_opkg, but
since opkg is not reasonably usable without the status information, we
can tie the distfeeds.conf to it.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Ensure /etc/opkg exists before trying to write there. This fixes a build
failure if SIGNED_PACKAGES is disabled.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
All the relevant options used for distfeeds.conf are part of base-files,
so it makes more sense to move the file there as well.
This has the added benefit that the we can share the opkg package again,
reducing the amount of target specific packages.
Acked-by: Jo-Philipp Wich <jo@mein.io>
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
- use %d instead of %n for opkg feed identifiers
- remove %n / %N references from version files
Fixes bf5cef47b3 merge: release/banner: drop release name and update banner.
Fixes FS#1213.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Kernel and rootfs in a subdirectory matching the userspace boardname,
was intended to use a single sysupgrade-tar archive for multiple boards
with different kernel/rootfs images. This feature was never used.
Use the first found directory in the tar archive instead of relying on
a directory named according to the userspace boardname.
It allows to change the boardname without adding another compatibility
layer - using the nand_board_name() function - for (sub)targets using
the metadata based image validation in favour to
nand_do_platform_check().
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch fixes two issues with the current get_partitions()
function.
First: "Invalid partition table on $disk" will pop up on
legitimate images on big endian system.
This is because the little-endian representation of "55 AA" is
assumed in the context of little-endian architectures. On these
comparing it to the 16-bit word 0xAA55 does work as intented.
Whereas on big-endian systems, this would have to be 0x55AA.
This patch fixes the issue by replacing the integer conversion
and value match check with just a string comparision.
Second: The extraction of the type, start LBA and LBA num from
the partition table has the same endianness issue. This has been
fixed by using the new hex_le32_to_cpu() function. This function
will translate the stored little-endian data to the correct
byte-order if necessary.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add the parent of the sysupgrade script to the list of pids not getting
killed
Signed-off-by: Mat Trudel <mat@geeky.net>
Signed-off-by: John Crispin <john@phrozen.org>
Shell function return code only has range [0, 255]. Other values will
be truncated, e.g. return 65536 will have the same effect as return 0
While at it, drop other "return $rc" where rc will almost always take
value 0 and whose value current callers actually do not check
Fixes FS#988
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
When we run "opkg install" on a package that installs an uci-defaults
script, functions.sh will fail to evaluate that script in its
default_postinst function.
This happens because there is no "./" present and it searches for the
file in paths specified by the PATH variable. This would work on bash,
but it will not work on ash and some other shells like sh, zsh. This
applys to the ". filename" directive used in this case.
This patch will make the path relative to the /etc/uci-defaults
directory.
Fixes: FS#1021
Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
Let the generic postinstall script invoke "kmodloader" when the just
installed package contains any /etc/module.d/ entries.
This allows us to skip the explicit "insert_module()" calls in the
package postinstall.
Due to the removed insert_module calls we do not need to assemble a
complete list of modules per package anymore, which allows for vast
simplification of the package generation code.
While we're at it, also support specifying default parameters for
modules using either the MODPARAM or MODPARAM.modulename variables
in KernelPackage.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The /bin/config_generate script and some other scripts are assuming the
/etc/config directory exists in the image. This is true in case for
example the package firewall, dropbear or dnsmasq are included, which
are adding the files under /etc/config/. Without any of these package
the system will not boot up fully because the /etc/config/ directory is
missing and some init scripts just fail.
Make sure all images with the base-files contain a /etc/config/
directory.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: John Crispin <john@phrozen.org>
Setting ipv6 to auto in case of a pppoe interface will trigger the
creation of a dynamic wan_6 interface meaning two IPv6 interfaces
(wan6 and wan_6) will be active on top of the pppoe interface.
This leads to unpredictable behavior in the network; therefore set
ipv6 to 1 which will prevent the dynamic creation of the wan_6
interface.
Further alias the wan6 interface on top of the wan interface for pppoe
as the wan6 interface can only be started when the link local address is
ready. In case of pppoe the link local address is negotiated during the
Internet Protocol Control Protocol when the PPP link is setup meaning
all the IP address info is only available when the wan interface is up.
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Set sysctl fs.suid_dumpable = 2
This allows suid processes to dump core according to kernel.core_pattern
setting. LEDE typically uses suid to drop root priviledge rather than
gain it but without this setting any suid process would be unable to
produce coredumps (e.g. dnsmasq)
Processes still need to set a non zero core file process limit ('ulimit
-c unlimited' or if procd used 'procd_set_param limits
core="unlimited"') in order to produce a core. This setting removes an
obscure stumbling block along the way.
>From https://www.kernel.org/doc/Documentation/sysctl/fs.txt
suid_dumpable:
This value can be used to query and set the core dump mode for setuid
or otherwise protected/tainted binaries. The modes are
0 - (default) - traditional behaviour. Any process which has changed
privilege levels or is execute only will not be dumped.
1 - (debug) - all processes dump core when possible. The core dump is
owned by the current user and no security is applied. This is
intended for system debugging situations only. Ptrace is unchecked.
This is insecure as it allows regular users to examine the memory
contents of privileged processes.
2 - (suidsafe) - any binary which normally would not be dumped is dumped
anyway, but only if the "core_pattern" kernel sysctl is set to
either a pipe handler or a fully qualified path. (For more details
on this limitation, see CVE-2006-2451.) This mode is appropriate
when administrators are attempting to debug problems in a normal
environment, and either have a core dump pipe handler that knows
to treat privileged core dumps with care, or specific directory
defined for catching core dumps. If a core dump happens without
a pipe handler or fully qualifid path, a message will be emitted
to syslog warning about the lack of a correct setting.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
With failsafe disabled there is no point in early network setup. We
don't send announcement over UDP and there is no way to ssh to the
device.
A side effect of this is avoiding a possibly incorrect network config
(only with failsafe disabled). This problem is related to possible
changes made by user in /etc/config/network.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
When processes don't die on SIGKILL (usually because of kernel bugs), it's
better to give up instead of looping forever.
upgraded will trigger a reboot in this case (and if this fails, a hardware
watchdog will eventually time out and reset the system, if present).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
For targets using the generic board detection and board specific
settings in diag.sh, the board name is still unset at the time the
set_state() provided by diag.sh is called by 10_indicate_preinit.
Change the execution order to ensure the boardname is populated before
required the first time. Do the target specific board detection as
early as possible, directly followed by the generic one to allow a
seamless switch to the generic function for populating /tmp/sysinfo/.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Depending on busybox applet selection, paths of basic utiilties may differ,
and may not work as symlinks to busybox. Simply using whatever binary is
found in PATH and detecting symlinks automatically is more robust and
easier to maintain.
The list of binaries is also slightly cleaned up and duplicates are
removed.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This is needed for an upcoming change to the hotplug default rules which
will cause /dev/tty* nodes to get assigned to the "tty" group in order
to support unprivileged user access when needed.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Including version.mk sets PKG_CONFIG_DEPENDS to config entries used for
VERSION_SED command. We should keep these configs to make sure package
gets refreshed when needed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
There already exist static assignment of uid/gid 65533 in packages feed
and we have nobody/nogroup taking 65534 as their ids. Let's change the
pid of dynamic assignment to start from 65536 so that the two assignment
scheme will not collide with each other
While at it, fix the scan command checking existence of uid/gid
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The offset and factor are only related for LEDs which can have
different brightness values. But binary LEDs are more common and don't
require any further configuation than setting the factor to 1.
Use offset = 0 and factor = 1 in case nothing else is specified.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Don't pass the value unconditionally to swconfig as a parameter but
instead only call reset if it is 1.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* Change network_get_subnet6() to sensibly guess a suitable prefix
Attempt to return the first non-linklocal, non-ula range, then attempt
to return the first non-linklocal range and finally fall back to the
previous behaviour of simply returning the first found item.
* Fix network_get_ipaddrs_all()
Instead of replicating the flawed logic appending a fixed ":1" suffix
to IPv6 addresses, rely on network_get_ipaddrs() and network_get_ipaddrs6()
to build a single list of all interface addresses.
* Fix network_get_subnets6()
Instead of replicating the flawed logic appending a fixed ":1" suffix
to IPv6 addresses, rely on the ipv6-prefix-assignment.local-address
field to figure out the proper network address.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Rework the network_get_ipaddr6() and network_get_ipaddrs6() functions to
fetch the effective local IPv6 address of delegated prefix from the
"local-address" field instead of naively hardcoding ":1" as static suffix.
Fixes FS#829.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
mvebu was modifying RAMFS_COPY_BIN and RAMFS_COPY_DATA from a
sysupgrade_pre_upgrade hook. As the ramfs is created from stage2, this
did not have an effect anymore after the staged sysupgrade changes.
As it doesn't really hurt to copy fw_printenv and fw_setenv
unconditionally, simply add them in /lib/upgrade/platform.sh, so stage2
will see them.
Config copying is moved to a function called by platform_copy_config, where
it belongs.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fixes: FS#821
Fixes: 30f61a34b4 "base-files: always use staged sysupgrade"
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
This patch is in continuation of: commit 93aa860405
"procd: nand: make it possible to configure kernel and ubi partition"
The $CI_KERNPART variable should be used in place
of the fixed "kernel" partition name. This allows
targets to specifiy alternate names for the kernel
partition.
Cc: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Some functions only used by stage2 are moved there from common.sh.
One piece that could still use more cleanup is platform_pre_upgrade: many
targets reference files from there are aren't available in the ramfs, so
we need to evaluate it before the switch; conversely, flash writes happen
in that function on some targets. Targets that do the latter should be
fixed eventually to use platform_do_upgrade for that purpose.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Support for the -d and -p options is dropped; it may be added again at some
point by adding these flags to the ubus sysupgrade call.
A downside of this is that we get a lot less information about the progress
of the upgrade: as soon as the actual upgrade starts, all shell sessions
are killed to allow unmounting the root filesystem.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
We always want to support staged upgrades now, so it's better to include
upgraded into the main package. /lib/upgrade/nand.sh is moved to
base-files.
The procd-nand-firstboot package is removed for now, it may return later
as a separate package.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This reverts commit e96a9a9af8.
The change breaks sysupgrade through LuCI and two-stage sysupgrade on
NAND targets. There is also a mismatch of file paths in lock and unlock
operations.
This commit was apparently neither properly tested, nor reviewed, so
drop it for now.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Bug introduced with 6713694.
I did not count on procd handling reload as mentioned
in this doc:
https://wiki.openwrt.org/inbox/procd-init-scripts
```
procd_set_param file /var/etc/your_service.conf # /etc/init.d/your_service reload will restart the daemon if these files have changed
procd_set_param netdev dev # likewise, except if dev's ifindex changes.
procd_set_param data name=value ... # likewise, except if this data changes.
```
The service would be restarted regardless of any of those params.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
uci_set_leds_ataport() allows to set a led to show activity
on a specific (s)ata port, which is needed for devices that have
a Sata led for each sata port.
The led trigger is from the 834-ledtrig-libata.patch LEDE kernel patch.
uci_set_leds_usbhost() allows to set a led to show total usb activity.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[Jo-Philipp Wich: use a single underscore to denote private functions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
create a function with code common to all led functions,
create another function with code common to functions setting
a simple led trigger, restore alphabetical order in function names.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[Jo-Philipp Wich: use a single underscore to denote private functions]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Commit 2036ae4 (base-files: support hostname and ntp servers through board.d)
was supposed to implement these procedures but lacked the required changes
to uci-defaults.sh.
Add the missing procedures now to fix config generation on targets relying
on hostname or NTP server presetting.
Fixes FS#754.
Reported-by: Cristian Morales Vega <cristian@samknows.com>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This was also working before, with a slightly
different semantic.
[ Original semantic ]
If no reload hooks was implemented, the default one would
kick in, it would return fail, and restart would happen.
This would happen also in the case where a reload hook
would be implemented, it would fail, and it would restart
the service.
[ New semantic ]
The default reload hook calls restart.
Services can implement their own reload.
If reload fails, then the '/etc/init.d/<service> reload'
would return a non-zero code, and the caller can choose
a way to handle this.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Overwrite an already set proto if a new one is passed to
_ucidef_set_interface() similar to what is done for the interface.
It is required when using ""ucidef_set_interface_wan 'ptm0' 'pppoe'"
after some initial wan interface configuration is already done by
ucidef_add_switch.
The "json_is_a protocol string" guard is meant to not reset an earlier
set interface proto in case something like
"ucidef_set_interface_lan 'eth0'" is used afterwards.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This can be used to tweak the buildbot behavior without having to change
buildbot's configuration.
It will also allow us to add more aggressive clean steps (e.g. on
toolchain changes), which would break developers' workflows if enable
by default.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When running wifi detect, the user will be told on error output that
wifi detect is deprecated, that wifi config must be used instead. Also
the commit that changes it is referenced for further info.
Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
Since commit 5f8f8a3661 wifi detect does
not longer work and wifi config it's used to configure not yet
configured wireless devices.
This commit changes command usage to reflect that change.
Signed-off-by: David Pinilla Caparrós <dpinitux@gmail.com>
Instead of only using tagged CPU port configurations when more than one VLAN
is present on the switch, always emit tagged configurations unless a board
explicitely opts out of this behaviour by using the previously introduced
[0-9]u@netdev syntax.
Emitting default tagged configurations has the following benefits:
- Relation of switch vlans to netdevs is easier to understand, especially
for multi-cpu-port switches
- Adding additional VLANs (e.g. to break out a LAN port for other purposes)
becomes easier as users are not forced to change the existing untagged
VLAN to tagged and the existing ifname notation from ethX to ethX.Y
anymore, drastly reducing the likelyhood of soft-bricks.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The condition is always true due to the literal string followed the
-n test parameter. A model name set by target scripts always gets
overwritten this way.
Change the condition to check for an already existing destination file
as it was before 5e85ae9 ("base-files: fix error message during boot").
Signed-off-by: Mathias Kresin <dev@kresin.me>
The name will appear in shell prompt and LuCI page title. Uppercase
letters seem to be more vigorous
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
If only a single opkg control file exists (which can happen with
CONFIG_CLEAN_IPKG), grep would not print the file name by default. Instead
of forcing it using -H, we just switch to -l (print only file names) and
get rid of the cut.
Add -s to suppress an error message when no control files exist.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Knowing the package architecture at runtime can be useful, e.g. to
configure opkg repository URLs. The value of ARCH_PACKAGES ("%A" in
VERSION_SED) as added to openwrt_release (as DISTRIB_ARCH) and os-release
(as LEDE_ARCH).
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
It has never been used by default (due to being too bloated), and it is
properly replaced by usign (which has been the default for a long time
now).
Remove this feature to simplify the build system
Signed-off-by: Felix Fietkau <nbd@nbd.name>
currently (after blogic's edit to my commit) it prints like this:
root@lede:/# service aa
aa does not exist. the following services are available :adblock dnsmasq gpio_switch rpcd system
boot done led sqm uhttpd
crelay dropbear log sysctl umount
cron firewall network sysfixtime urandom_seed
ddns fstab odhcpd sysntpd
which looks pretty bad, and is even worse if someone writes only "service" without arguments, as it will print " does not exist. " which is confusing.
with this commit it looks like this:
root@lede:/# service
service "" not found, the following services are available:
adblock dnsmasq gpio_switch rpcd system
boot done led sqm uhttpd
crelay dropbear log sysctl umount
cron firewall network sysfixtime urandom_seed
ddns fstab odhcpd sysntpd
Yes there is some play with " and ', it is to display "name" or just "" if no service name is entered (like in the example).
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
This adds support for install-overlay define. When used in package it
allows installing files to a special directory that gets copied to the
root when installing it.
It allows overwriting files provided by other packages.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Calling a build ##.##-CURRENT might mislead users into thinking that this
build is the most current release of a branch.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Now that the VERSION_NUMBER variable holds the human friendly name and not
the commit ID anymore, we need to support adding the revision ID as well.
Introduce a new config variable CONFIG_VERSION_CODE_FILENAMES which, if set,
causes the resulting file names to contain a commit ID designation as printed
by scripts/getver.sh.
Also sanitize the input variables to ensure that the resulting strings are
lowercased and no not contain spaces.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
