Commit e52c57bb1b renamed all
network ports to match the faceplate of the Gowin 1U Rack
Mount Server and added the br-lan bridge for the eth* ports.
This commit adds the PoE port to the br-lan bridge and a
br-wan bridge for the two SFP ports so that all ports are
part of the default network configuration.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/16965
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This adds auto-configuration of network ports on Dell EMC Edge620 (x86) product.
It is similar in specs/features to some of the Sophos x86-based appliances, but:
1. Serial console terminal is built in and requires just the micro-USB cable
2. Comes with both MMC (16Gb) and SSD (256Gb) installed
3. Comes with 6 ethernet ports all 6 are functional when no SFP is used
4. Comes with two SFP cages and not one, like some of revision 3 Sophos products
5. Unlike Sophos devices, there are no non-wireless models of Edge 620,
it comes with Qualcomm Atheros QCA9880 radio
These devices can be now found both second-hand and new at online marketplaces below
(sometimes well below) US $100, I believe they make great candidates for running OpenWrt.
The ethernet network ports on the case are marked GE1 thru to GE6 with the
following mapping once booted into OpenWrt:
```
GE1: eth2: pci0000:00/0000:00:0b.0/0000:02:00.2
GE2: eth3: pci0000:00/0000:00:0b.0/0000:02:00.3
GE3: eth0: pci0000:00/0000:00:0b.0/0000:02:00.0
GE4: eth1: pci0000:00/0000:00:0b.0/0000:02:00.1
GE5: eth7: pci0000:00/0000:00:17.0/0000:07:00.1
GE6: eth6: pci0000:00/0000:00:17.0/0000:07:00.0
```
Dell's instructions for [standard configuration](https://infohub.delltechnologies.com/en-us/l/dell-emc-edge-620-advanced-activation-guide/dell-emc-sd-wan-edge-620-standard-configuration/)
recommend using GE3, GE4, GE5, or GE6 for WAN, I've selected the GE6 as the sole
WAN port under OpenWrt with the rest of ethernet ports assigned to LAN.
Please merge before 24.xx is forked and if possible, cherry-pick for 23.05
if there's no ETA for 24.xx forking.
PS. @Hurricos I'm struggling with ixgbe mappings on Sophos devices which use
very similar hardware to Dell EMC, so even tho I know the sys paths for ethernet ports,
I'd prefer to do a separate commit to properly map ethernet ports to match the case markings
for this device at some point later.
Signed-off-by: Stan Grishin <stangri@melmac.ca>
This reverts commit 3004c20614.
The commit added the needed packages for the new target
to the generic x86_64 image. This results into unwanted
modules and firmware files for other x86 devices.
Additionally, there is the following error message
while booting the image on other x86 devices:
[ 8.531720] kmodloader: 1 module could not be probed
[ 8.532613] kmodloader: - leds-mlxcpld - 0
For now, the needed packages will have to be selected
manually while configuring the image.
Signed-off-by: Til Kaiser <til.kaiser@gmx.de>
Some platforms have their console on other ports than ttyS0, so
allow the developer to tailor this on bespoke platform images.
Fixes issue #13401.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
The Mellanox Spectrum SN2000 Series Switches are Managed Ethernet
Switches with a maximum speed of 100Gb/s and up to 56 ports.
Tested on a Mellanox Spectrum SN2100 with the following specs:
- CPU: Intel ATOM x86 dual-core 2.4GHz
- RAM: 8GB
- Disk: 16GB SSD
- Ports: 16x QSFP28 100GbE, 1x 100M Mgmt Port, 1x RJ45 Serial Port
- USB: 1x mini 2.0
- Button: 1x (reset)
- LEDs: 6x
Installation:
- Create a bootable USB device (either by flashing this image
onto it or another Linux distribution)
- Unzip the generic OpenWrt x64 image
and copy it onto the USB device
- Plug the USB device into the Mellanox Switch and boot from it
- Flash the image (e.g., with dd) onto the internal SSD
of the switch (should be /dev/sda)
To enter the BIOS, reboot the switch and press CTRL+B while you see
the BIOS information text (American Megatrends …). The default password
to enter the BIOS is admin. To boot from the USB device, switch to the
Boot index tab and set your USB device at the top of the boot order
(the internal SSD should be currently there). Don't forget to set
the SSD back at the top after you have flashed the image.
Signed-off-by: Til Kaiser <til.kaiser@gmx.de>
[unify with generic x64 image]
Signed-off-by: David Bauer <mail@david-bauer.net>
The Sophos SG/XG-135 revision 3 has odd numbering of eth ports
where the WAN port (as marked on the case) is:
`eth6` and `eth0`, `eth1`, `eth2`, `eth3`, `eth5`, `eth7`, `eth8` are LAN ports.
Port `eth4` seems to be the SFP port.
Also add the missing LED definition for supported Sophos devices.
Original discussion at:
https://forum.openwrt.org/t/openwrt-on-revision-3-of-sophos-desktop-appliances/152912
Signed-off-by: Stan Grishin <stangri@melmac.ca>
This hack was to bring all existing installations to the newest GRUB
version as fast as possible. Since 19.07.x is EoL we can assume this
task is completed. Now sysupgrade will solely be responsible for
bootloader upgrade.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Match interface numbers with printed numbers on device enclosure and
assign first port as WAN interface.
Notes
Serial console is available through RJ-45 port with Cisco pinout
baud: 19200, parity: none, flow control: none
The device is setup with UEFI. To enter setup hold DEL or ESC key on
boot. Default UEFI Administrator password is: bcndk1
For users using graphics IC it's advisable to disable display with:
i915.disable_display=1
appending to kernel command line inside bootloader, to save about
0.5-0.6W energy on idle.
For users not using graphics IC, disable it in UEFI, this will save about
1.5W energy on idle.
Pins marked CN19 are ATX power On/Off button.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
The Meraki MX100 has ten 1000BASE-T and 2 SFP ethernet ports through
3, 4-port PCIe devices. The default enumeration of these network
devices' names does not correspond to their labeling. Fix this by
explicitly naming the devices, mapping against their sysfs path.
Note that these default network names can only be up to 8 characters,
because we can have up to 8 characters of modifiers (e.g. ^br-,
.4096$), and because the maximum network interface name is 16
characters long.
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
[lowercase subject]
Signed-off-by: Paul Spooren <mail@aparcar.org>
This commit builds on previous efforts to add support
for Sophos devices.
* Add support for Sophos XG 85 with/without wireless
* Add support for Sophos XG 86 with/without wireless
Tested on Sophos XG 85w rev1 and XG 86 rev 1
Signed-off-by: Raylynn Knight <rayknight@me.com>
This reverts commit 80b7a8a7f5.
Now that 5.10 is the default kernel for all platforms, we can
bring back the NU801 userspace driver for platforms that rely
on it. Currently it's used on the MX100 x86_64 target, but
other Meraki platforms use this controller.
Note that we also now change how we load nu801. The way we did
this previously with procd worked, but it meant it didn't load
until everything was up and working.
To fix this, let's call nu801 from boot and re-trigger the
preinit blink sequence. Since nu801 runs as a daemon this is
now something we can do.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
(removed empty line, currently only MX100 uses it so: @TARGET_x86)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Previously, grub2 was hardcoded to always look on "hd0" for the
kernel.
This works well when the system only had a single disk.
But if there was a second disk/stick present, it may have look
on the wrong drive because of enumeration races.
This patch utilizes grub2 search function to look for a filesystem
with the label "kernel". This works thanks to existing setup in
scripts/gen_image_generic.sh. Which sets the "kernel" label on
both the fat and ext4 filesystem variants.
Signed-off-by: Jax Jiang <jax.jiang.007@gmail.com>
Suggested-by: Alberto Bursi <bobafetthotmail@gmail.com> (MX100 WA)
(word wrapped, slightly rewritten commit message, removed MX100 WA)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Correct typo that caused network interfaces for Sophos
SG/XG wireless devices to not be configured properly.
Tested on Sophos SG 135wr2, Sophos XG 125wr2 and
Sophos SG 105wr1
Signed-off-by: Raylynn Knight <rayknight@me.com>
Fall back to using board_vendor and board_name, if known dummy values
are used for sys_vendor and product_name.
Examples:
To be filled by O.E.M.:To be filled by O.E.M.
--> INTEL Corporation:ChiefRiver
System manufacturer:System Product Name
--> ASUSTeK COMPUTER INC.:P8H77-M PRO
To Be Filled By O.E.M.:To Be Filled By O.E.M.
--> ASRock:Q1900DC-ITX
Gigabyte Technology Co., Ltd.:To be filled by O.E.M.
--> Gigabyte Technology Co., Ltd.:H77M-D3H
empty:empty
--> TYAN Computer Corporation:TYAN Toledo i3210W/i3200R S5211
To Be Filled By O.E.M.:To Be Filled By O.E.M.
--> ASRock:H77 Pro4-M
Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* Add support for Sophos SG/XG-115 r1, r2 with/without wireless
* Add support for Sophos SG/XG-125 r1, r2 with/without wireless
* Add wireless support for SG/XG-105
Signed-off-by: Raylynn Knight <rayknight@me.com>
* Better product ID for Sophos SG/XG-105 models
* Add support for Sophos SG/XG-135 r1, r2 with/without wireless
Signed-off-by: Stan Grishin <stangri@melmac.ca>
[Changed subject to x86 - probably eaten somewhere, the PR had it]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This reverts commit f536f5ebdd.
As Hauke commented, this causes builder failures on 5.4 kernels.
This revert includes changes to the mx100 kernel modules
dependency as well as the uci led definitions.
Tested-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit will add support for the Meraki MX100 in OpenWRT.
Specs:
* CPU: Intel Xeon E3-1200 Series 1.5GHz 2C/4T
* Memory: 4GB DDR3 1600 ECC
* Storage: 1GB USB NAND, 1TB SATA HDD
* Wireless: None
* Wired: 10x 1Gb RJ45, 2x 1Gb SFP
UART:
The UART header is named CONN11 and is found in the
center of the mainboard. The pinout from Pin 1 (marked
with a black triangle) to pin 4 is below:
Pin 1: VCC
Pin 2: TX
Pin 3: RX
Pin 4: GND
Note that VCC is not required for UART on this device.
Booting:
1. Flash/burn one of the images from this repo to a
flash drive.
2. Take the top off the MX100, and unplug the SATA
cable from the HDD.
3. Hook up UART to the MX100, plug in the USB drive,
and then power up the device.
4. At the BIOS prompt, quickly press F7 and then
scroll to the Save & Exit tab.
5. Scroll down to Boot Override, and select the
UEFI entry for your jumpdrive.
Note: UEFI booting will fail if the SATA cable for
the HDD is plugged in.
The issue is explained under the Flashing instructions.
Flashing:
1. Ensure the MX100 is powered down, and not plugged
into power.
2. Take the top off the MX100, and unplug the SATA
cable from the HDD.
3. Using the Mini USB female port found by the SATA
port on the motherboard,
flash one of the images to the system. Example:
`dd if=image of=/dev/sdb conv=fdatasync` where sdb
is the USB device for the MX100's NAND.
4. Unplug the Mini USB, hook up UART to the MX100,
and then power up the device.
5. At the BIOS prompt, quickly press F7 and then
scroll to the Boot tab.
6. Change the boot order and set UEFI: USB DISK 2.0
as first, and USB DISK 2.0 as second.
Disable the other boot options.
7. Go to Save & Exit, and then select Save Changes and
Reset
Note that OpenWRT will fail to boot in UEFI mode when
the SATA hard drive is plugged in. To fix this, boot
with the SATA disk unplugged and then run the following
command:
`sed -i "s|hd0,gpt1|hd1,gpt1|g" boot/grub/grub.cfg`
Once the above is ran, OpenWRT will boot when the HDD
is plugged into SATA. The reason this happens is the
UEFI implementation for the MX100 will always set
anything on SATA to HD0 instead of the onboard USB
storage, so we have to accomidate it since OpenWRT's
GRUB does not support detecting a boot disk via UUID.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Similar to how this is done in the diag.sh found in the base-files
package, we should blink our status LED (if we have one) during the
upgrade process. This follows the same blink pattern as seen at
./package/base-files/files/etc/diag.sh#L36
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
eth0 -> single NIC (i211at)
eth1 -> single NIC (i211at) -> 4-port unmanaged switch (BCM53125U)
Notes
UART is exposed on J4 connector, pinout starting from pin marked 1:
1. GND, 2. NC?, 3. NC?, 4. RX, 5. TX, 6. NC?
baud: 115200, parity: none, flow control: none
The board is setup by coreboot with UEFI. To enter setup screen hold
ESC key on boot.
The 5-LED multicolor matrix is attached on first I2C device named
"Synopsys DesignWare I2C adapter" at address 0x60. Controlling values
are stored in /opt/roqos/etc/rcLED.conf of original firmware.
Remember to backup the original firmware, there are no downloadable
copies.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
This adds detection of the Sophos SG-105 and Sophos XG-105 models
and assignment of ethernet ports these models have to LAN/WAN.
Signed-off-by: Stan Grishin <stangri@melmac.net>
So far, board.d files were having execute bit set and contained a
shebang. However, they are just sourced in board_detect, with an
apparantly unnecessary check for execute permission beforehand.
Replace this check by one for existance and make the board.d files
"normal" files, as would be expected in /etc anyway.
Note:
This removes an apparantly unused '#!/bin/sh /etc/rc.common' in
target/linux/bcm47xx/base-files/etc/board.d/01_network
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This driver adds the LED support for the PC Engines APU1.
This integrates the Linux kernel driver and includes a patch to support
newer firmware versions. Also the default LED configuration is updated
to use the correct devices.
Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
The comment content can be useful for readers of both the log and code
Previously when dd command "records in/out" messages are not filtered
like now with get_image_dd, it's not clear that these messages are for
extracting boot sectors. E.g.
Before
== upgrade: Reading partition table from bootdisk...
37+26 records in
37+26 records out
== upgrade: Reading partition table from image...
After
== upgrade: Reading partition table from bootdisk...
== upgrade: Extract boot sector from the image
37+26 records in
37+26 records out
== upgrade: Reading partition table from image...
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The mount point is "/tmp/boot", the path in the boot partition is
"/boot/grub/upgraded".
Origin of this mark b9c1cf16 ("x86: add preinit hook for bootloader
upgrade")
Fixes 32f675ca ("x86: fix grub-bios-setup fail during sysupgrade")
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3140
Reported-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
grub-bios-setup requires two images (boot.img and core.img),
but they are missing. This make an error during sysupgrade:
Upgrading bootloader on /dev/sda...
grub-bios-setup: error: cannot open `/tmp/boot/boot/grub/boot.img': No
such file or directory.
Signed-off-by: 李国 <uxgood.org@gmail.com>
Add EFI platform bootable images for x86 platforms. These images can
also boot from legacy BIOS platform.
EFI System Partition need to be fat12/fat16/fat32 (not need to load
filesystem drivers), so the first partition of EFI images are not ext4
filesystem any more.
GPT partition table has an alternate partition table, we did not
generate it. This may cause problems when use these images as qemu disk
(kernel can not find rootfs), we pad enough sectors will be ok.
Signed-off-by: 李国 <uxgood.org@gmail.com>
[part_magic_* refactoring, removed genisoimage checks]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This commit fills the void for current OpenWrt installations which will
be still on old bootloader version even after "x86: add bootloader
upgrade on sysupgrade", since it performs bootloader upgrade only on
sysupgrade. To keep all OpenWrt deploynents on the same GRUB version,
add preinit hook, which will perform upgrade of the bootloader on first
boot after sysupgrade.
It's temporary solution and should be deleted, when the first release
including this hook will no longer be supported by OpenWrt team.
We can assume that all installations should be on current bootolader
version and from there sysupgrade routine will be sufficient.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Currently bootloader always stays on the same version as when first
written to boot medium (not true if partition layout changed, which will
trigger sysupgrade process to write full disk image). That creates
inconveniences as it always stays with same features or/and bugs. Users
wishing to add support to additional modules or new version, would need
to write the whole image, potentially destroying previous system
configuration. To fix these, this commit adds additional routine to
sysupgrade which upgrades unconditionally the bootloader to the latest
state provided by OpenWrt.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
It's a variable set by procd that should replace hardcoded
/tmp/sysupgrade.tgz.
This change requires the most recent procd with the commit 0f3c136
("sysupgrade: set UPGRADE_BACKUP env variable").
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
$CONF_TAR shouldn't be assumed to always point to the sysupgrade.tgz.
This change makes code more generic and allows refactoring $CONF_TAR.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
1) Add BACKUP_FILE and use it when copying an archive to be restored
after sysupgrade (on the next preinit).
2) Use CONF_TAR for copying backup prepared by the /sbin/sysupgrade
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This explicitly lets stage2 know if partitions should be preserved. No
more "touch /tmp/sysupgrade.always.overwrite.bootdisk.partmap" hack.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
When running OpenWrt inside an LXC container no shell is opend as LXC
defaults to a virtual /dev/console.
This patch allows to enter a shell after starting the container via
`lxc-start`, without it is only posible to access a shell on tty1 via
`lxc-console`.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Moving binding mount before check for saved sysupgrade configuration
made it unreachable. Fix it by moving binding mount after the check.
Fixes: f78b2616 (x86: mount writable bootfs)
Reported-by: Lucian Cristian <luci@powerneth.ro>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Create initrd enries for x86 images, that'll load amd microcode as early
as possible. Also remove the preinit script responsible for late load of
microcode.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Create initrd enries for x86 images, that'll load intel microcode as
early as possible. To achieve that the test module for grub is enabled
which provides shell-like conditionals. Also restrict the late load of
microcode to AMD processors.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Mount boot file system with rw option to allow installation of packages
which install files to /boot directory.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
There is a new APU-model available, APU3. The device is configured in
the same way as the APU1 and APU2, so the same LED/network setup can be
used.
I considered changing the case to pc-engines-apu*, but I chose to follow
the existing pattern and add the full board name.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
