So far, WiFi MAC addresses for this device have been set up from
caldata. However, this returns values which do not look like MAC
addresses. They also do not match stock firmware:
wlan0 (5.0): 00:11:22:00:17:D0 from 0x8004
wlan1 (2.4): 00:11:22:00:17:CD from 0x4 (and 0x2e)
It looks like the only valid MAC address on this device is at 0x28.
So, this patch changes setup to calculate addresses based on the
value at 0x28:
lan: *:0A (flash, label)
wan: *:0B (flash + 1)
wifi2: *:0A (flash)
wifi5: *:0C (flash + 2)
Thanks to Roger Pueyo Centelles <roger.pueyo@guifi.net> for
investigating this on his devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit d1072096f4)
Update libevent to 2.1.11
Use CMake instead GNU Autotools
Backport following commits:
f05ba67193
..and partially
7201062f3e
to fix compilation
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
(cherry picked from commit f351beedfd)
(resolves FS#2435)
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The kconfig symbol is an invisible one since its introduction. It is
not supposed to be enabled on its own.
Resolves FS#1821
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
(cherry picked from commit 4bf9bec361)
Improves rate control responsiveness and performance
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[reworked to apply on 4.19.79 mac80211 + renumbered + refreshed]
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
The Unifi AC-LR has identical hardware to the Unifi AC-Lite.
The antenna setup is different according to the vendor,
which explains the thicker enclosure.
Therefore, it is helpful to know the exact device variant,
instead of having "Ubiquiti UniFi-AC-LITE/LR".
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
[fix legacy name in commit message; add old boardname to
SUPPORTED_DEVICES]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 07c1ddf522)
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds correct model detection for UniFi
AC-LR. Previously, said device was incorrectly detected
as UniFi-AC-LITE/MESH.
The Information about the device is stored at 0xC in the EEPROM
partition. It corresponds to the sysid in /etc/board.info of the
Ubiquiti stock firmware.
Signed-off-by: Andreas Ziegler <dev@andreas-ziegler.de>
[adjust naming style of target to existing ones]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 2bc7c519dc)
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes frequent crashes observed on a UniFi AC Mesh using OpenWrt
master and 19.07. 18.06 seems not affected from our testing.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 641a93f0f2)
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit changes the source of the Wave 1 ath10k-firmware
from linux-firmware to Kall Valos ath10k-firmware repository.
This is necessary as the firmware selected in linux-firmware produces
frequent crashes in some circumstances.
This patch can be removed as soon as linux-firmware carries
10.2.4-1.0-00047 firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit a3914783a3)
Signed-off-by: David Bauer <mail@david-bauer.net>
Several Archer Cxx devices were using board-specific LED names in
ar71xx, which were changed to "tp-link:*" in ath79.
This patch adds migration for them.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 53e6cc7a81)
Several devices added to LED migration script will just have their
(old) board name converted to tp-link.
By using a variable for this, the amount of code in the migration
script can be reduced and the chance for typos is reduced.
This patch also introduces the marker for beginning of a pattern
"^" to the regex, so the match is more specific.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 6b0eb84336)
The code line patching ath9k MAC address for this device contains
a wrong number of arguments including an unset "$mac", which
looks like a typo or copy/paste mistake.
This has been introduced already in the device support commit
745dee11ac ("ath79: add support for WD My Net Wi-Fi Range
Extender").
This patch just removes the "$mac" argument, leaving a formally
valid line. (No on-device test has been performed.)
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 6b53033783)
The ar71xx images for the Ubiquiti NanoStation M (XM) devices use
"nanostation-m" as board name, but the ath79 images are only
compatible with the "nano-m" board name, so sysupgrade complains.
By changing this additional supported device, sysupgrade smoothly
upgrades from ar71xx to ath79.
Ref: openwrt#2418
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit f473ce6f23)
The ar71xx images for the Ubiquiti NanoStation M (XW) devices use
"nanostation-m-xw" as the board name, but the ath79 images are only
compatible with the "nano-m-xw" board name, so sysupgrade complains.
By adding this additional supported device, sysuspgrade smoothly
upgrades from ar71xx to ath79.
Tested on a NanoStation M (XW) running OpenWrt ar71xx r10250-016d1eb.
Ref: https://github.com/openwrt/openwrt/pull/2418
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[removed duplicate DEVICE_VARIANT, removed uneeded nano-m-xw support]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 6dda2ea6ad)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The device did not appear to be reachable unless the connection were
forced to 100Mb or lower. Revert to previously working pll-data.
Also fix the phy-mode to represent the actual state needed for ethernet
to function.
Reported-by: Moritz Schreiber <moritz@mosos.de>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
[add remark about phy-mode property]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit ee41b602a2)
edma_read_append_stats() gets called from two places in the driver.
The first place is the kernel timer that periodically updates
the statistics, so nothing gets lost due to overflows.
The second one it's part of the userspace ethtool ioctl handler
to provide up-to-date values.
For this configuration, the use of spin_lock() is not sufficient
and as per:
<https://mirrors.edge.kernel.org/pub/linux/kernel/people/rusty/kernel-locking/c214.html>
the locking has to be upgraded to spin_lock_bh().
Signed-off-by: Masafumi UTSUGI <mutsugi@allied-telesis.co.jp>
[folded patch into 710-, rewrote message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit f1d761f95e)
This adds engine configuration sections to openssl.cnf, with a commented
list of engines. To enable an engine, all you have to do is uncomment
the engine line.
It also adds some useful comments to the devcrypto engine configuration
section. Other engines currently don't have configuration commands.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit cebf024c4d)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This corrects the additional boardname for the image metadata to the one
used in ar71xx. The previously present additional entry was never used
on a running system.
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 1a256470e7)
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit fixes TP-Link TL-WDR4900 v1 MAC address assignment.
Previously, the MAC addrss was read for the ethernet from the "config"
partition. However, the content of this partition is dependent on the
firmware which was previously installed on the device.
Switch the MAC address source to the U-Boot partition, where the MAC
address is always present at a fixed partition. The partition was
previously already used for the WiFi MAC-addresses.
Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 07e555d873)
Signed-off-by: David Bauer <mail@david-bauer.net>
The default sizes render Device/linksys_audi mage un-flashable.
Restore the pagesize, subpagesize, and blocksize for linksys_audi
from https://github.com/openwrt/archive.
Signed-off-by: Eubert Bao <bunnier@gmail.com>
(cherry picked from commit e11fc8439c)
The first allows usage of several functions in the std namespace, which
broke compilation of gddrescue specifically with uClibc-ng and uClibc++.
The second allows usage of long long with normal C++11, which is part of
the standard. Before, std=gnu++11 needed to be passsed to work around it.
As a result of the second patch, the pedantic patch can safely be removed.
Both patches are upstream backports.
Added -std=c++11 to CFLAGS to guarentee proper inclusion of long long.
Added another patch that fixes a typo with the long long support. Sent to
upstream.
Fixed up license information according to SPDX.
Small cleanups for consistency.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(cherry picked from commit 6ab386c9bc)
Upon writing to "remove" file, debugfs_remove_recursive() blocks while
holding rtnl_lock. This is because debugfs' file_ops callbacks are
executed in debugfs_use_file_*() context which prevents file removal.
Fix this by only flagging the device for removal and then do the cleanup
in file_ops.release callback which is executed out of that context.
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
(cherry picked from commit c2635b871d)
Since v3.11, netdevice notification data are of type
"struct netdev_notifier_info". Handle it as such!
This should fix a critical bug in which devices are unable get released
because trelay does not release resources in response to UNREGISTER
event spamming the log with something like:
unregister_netdevice: waiting for eth0.1 to become free. Usage count = 1
Signed-off-by: Ali MJ Al-Nasrawy <alimjalnasrawy@gmail.com>
(cherry picked from commit 77cfc0739d)
if gcc not linker whith this LDFLAGS, "file libbz2.so.1.0.8" will
recognize as pie executable ELF file ( which should be shared object).
this because the file command version before 5.36 not recognize
correctly.
Signed-off-by: leo chung <gewalalb@gmail.com>
(cherry picked from commit 56ab58fb6c)
This fixes a compilation error as follows:
drivers/staging/fsl_qbman/qman_config.c:815:29: error: bitwise comparison
always evaluates to false [-Werror=tautological-compare]
if ((qman_ip_rev & 0xFF00) == QMAN_REV31) {
Signed-off-by: Biwen Li <biwen.li@nxp.com>
(cherry picked from commit 53b73131e9)
The prepare target was added some 11 years ago to build tools and
toolchain and was recently extended to create buildinfo files for
reproducibility, meaning {feeds,version,config}.buildinfo.
As the buildbot workflow is more complex than the single prepare (kmod
feed insertion), prepare is only used to create those buildinfo files.
Running prepare however runs `target/compile` as well, taking time even
everything is already compiled.
Splitting this allows the buildbot to run only the `buildinfo` target
while others can still use the convenience feature `prepare`.
Signed-off-by: Paul Spooren <mail@aparcar.org>
(cherry picked from commit 6caf437652)
The destination buffer size `d_len` is passed to `lzma_inflate` as a
pointer. Therefore, it needs to be dereferenced to compare its content.
Signed-off-by: Christian Franke <nobody@nowhere.ws>
(cherry picked from commit d544bc84a0)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The fwutil command will interpret the final 16 byte of a given firmware
image files as "struct fwimage_trailer".
In case these bytes do look like a valid trailer, we must ensure that we
print them out along with the remainder of the image to not accidentally
truncate non-trailer-images by 16 bytes when they're piped through fwtool,
e.g. as part of an image verification command sequence.
Some command sequences pipe images through fwtool in order to strip any
possible metadata, certificate or signature trailers and do not expect
bare images without any of that metadata to get truncated as other non-
fwtool specific metadata is expected at the end of the file, e.g. an
information block with an md5sum in case of the combined image format.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 889b841048)
The switch port naming in LuCI does not fit the physical numbers
on the front of this device. Since this is confusing, fix it.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
(cherry picked from commit e56e5a454e)
GDB 8.3.1 brings the following fixes and enhancements over GDB 8.3:
PR c++/20020 (GDB segfault on printing objects)
PR gdb/24454 (nat/x86-linux-dregs.c failed assertion)
PR breakpoints/24541 (Incorrect evaluation of systemtap probes due to register being signed and probe expression assuming unsigned)
PR symtab/24545 (Symbol loading performance regression with cc1)
PR gdb/24592 (amd64->i386 linux syscall restart problem)
PR gdb/25009 (terminate called after throwing an instance of 'srchilite::ParserException')
PR gdb/25010 (Calls to error () can cause SIGTTOU to send gdb to the background)
PR breakpoints/25011 (Breakpoints on file reloads broken for PIE binaries)
This corrective release also brings the following testsuite fixes and
enhancements:
PR testsuite/25005 (gdb-caching-proc.exp takes a lot of time on skip_opencl_tests)
PR testsuite/25016 (Test-case failures for -pie)
GDB 8.3 includes the following changes and enhancements:
* Support for new native configurations (also available as a target configuration):
- RISC-V GNU/Linux (riscv*-*-linux*)
- RISC-V FreeBSD (riscv*-*-freebsd*)
* Support for new target configurations:
- CSKY ELF (csky*-*-elf)
- CSKY GNU/Linux (csky*-*-linux)
- NXP S12Z ELF (s12z-*-elf)
- OpenRISC GNU/Linux (or1k*-*-linux*)
* Native Windows debugging is only supported on Windows XP or later.
* The Python API in GDB now requires Python 2.6 or later.
* GDB now supports terminal styling for the CLI and TUI.
Source highlighting is also supported by building GDB with GNU
Highlight.
* Experimental support for compilation and injection of C++ source
code into the inferior (requires GCC 7.1 or higher, built with
libcp1.so).
* GDB and GDBserver now support IPv6 connections.
* Target description support on RISC-V targets.
* Various enhancements to several commands:
- "frame", "select-frame" and "info frame" commands
- "info functions", "info types", "info variables"
- "info thread"
- "info proc"
- System call alias catchpoint support on FreeBSD
- "target remote" support for Unix Domain sockets.
* Support for displaying all files opened by a process
* DWARF index cache: GDB can now automatically save indices of DWARF
symbols on disk to speed up further loading of the same binaries.
* Various GDB/MI enhancements.
* GDBserver on PowerPC GNU/Linux now supports access to the PPR,
DSCR, TAR, EBB/PMU, and HTM registers.
* Ada task switching support when debugging programs built with
the Ravenscar profile added to aarch64-elf.
* GDB in batch mode now exits with status 1 if the last executed
command failed.
* Support for building GDB with GCC's Undefined Behavior Sanitizer.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
GDB 8.3.1 brings the following fixes and enhancements over GDB 8.3:
PR c++/20020 (GDB segfault on printing objects)
PR gdb/24454 (nat/x86-linux-dregs.c failed assertion)
PR breakpoints/24541 (Incorrect evaluation of systemtap probes due to register being signed and probe expression assuming unsigned)
PR symtab/24545 (Symbol loading performance regression with cc1)
PR gdb/24592 (amd64->i386 linux syscall restart problem)
PR gdb/25009 (terminate called after throwing an instance of 'srchilite::ParserException')
PR gdb/25010 (Calls to error () can cause SIGTTOU to send gdb to the background)
PR breakpoints/25011 (Breakpoints on file reloads broken for PIE binaries)
This corrective release also brings the following testsuite fixes and
enhancements:
PR testsuite/25005 (gdb-caching-proc.exp takes a lot of time on skip_opencl_tests)
PR testsuite/25016 (Test-case failures for -pie)
GDB 8.3 includes the following changes and enhancements:
* Support for new native configurations (also available as a target configuration):
- RISC-V GNU/Linux (riscv*-*-linux*)
- RISC-V FreeBSD (riscv*-*-freebsd*)
* Support for new target configurations:
- CSKY ELF (csky*-*-elf)
- CSKY GNU/Linux (csky*-*-linux)
- NXP S12Z ELF (s12z-*-elf)
- OpenRISC GNU/Linux (or1k*-*-linux*)
* Native Windows debugging is only supported on Windows XP or later.
* The Python API in GDB now requires Python 2.6 or later.
* GDB now supports terminal styling for the CLI and TUI.
Source highlighting is also supported by building GDB with GNU
Highlight.
* Experimental support for compilation and injection of C++ source
code into the inferior (requires GCC 7.1 or higher, built with
libcp1.so).
* GDB and GDBserver now support IPv6 connections.
* Target description support on RISC-V targets.
* Various enhancements to several commands:
- "frame", "select-frame" and "info frame" commands
- "info functions", "info types", "info variables"
- "info thread"
- "info proc"
- System call alias catchpoint support on FreeBSD
- "target remote" support for Unix Domain sockets.
* Support for displaying all files opened by a process
* DWARF index cache: GDB can now automatically save indices of DWARF
symbols on disk to speed up further loading of the same binaries.
* Various GDB/MI enhancements.
* GDBserver on PowerPC GNU/Linux now supports access to the PPR,
DSCR, TAR, EBB/PMU, and HTM registers.
* Ada task switching support when debugging programs built with
the Ravenscar profile added to aarch64-elf.
* GDB in batch mode now exits with status 1 if the last executed
command failed.
* Support for building GDB with GCC's Undefined Behavior Sanitizer.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
(cherry picked from commit 942f020bf4d0f49e4c5586a59ddf21c00e9d8bbe)
1.1.24 release notes
new features:
- GLOB_TILDE extension to glob
- non-stub catgets localization API, using netbsd binary catalog format
- posix_spawn file actions for [f]chdir (extension, pending future standard)
- secure_getenv function (extension)
- copy_file_range syscall wrapper (Linux extension)
- header-level support for new linux features in 5.2
performance:
- new fast path for lrint (generic C version) on 32-bit archs
major internal changes:
- functions involving time are overhauled to be time64-ready in 32-bit archs
- x32 uses the new time64 code paths to replace nasty hacks in syscall glue
compatibility & conformance:
- support for powerpc[64] unaligned relocation types
- powerpc[64] and sh sys/user.h no longer clash with kernel asm/ptrace.h
- select no longer modifies timeout on failure (or at all)
- mips64 stat results are no longer limited to 32-bit time range
- optreset (BSD extension) now has a public declaration
- support for clang inconsistencies in wchar_t type vs some 32-bit archs
- mips r6 syscall asm no longer has invalid lo/hi register clobbers
- vestigial asm declarations of __tls_get_new are removed (broke some tooling)
- riscv64 mcontext_t mismatch glibc's member naming is corrected
bugs fixed:
- glob failed to match broken symlinks consistently
- invalid use of interposed calloc to allocate initial TLS
- various dlsym symbol resolution logic errors
- semctl with SEM_STAT_ANY didn't work
- pthread_create with explicit scheduling was subject to priority inversion
- pthread_create failure path had data race for thread count
- timer_create with SIGEV_THREAD notification had data race getting timer id
- wide printf family failed to support l modifier for float formats
arch-specific bugs fixed:
- x87 floating point stack imbalance in math asm (i386-only CVE-2019-14697)
- x32 clock_adjtime, getrusage, wait3, wait4 produced junk (struct mismatches)
- lseek broken on x32 and mipsn32 with large file offsets
- riscv64 atomics weren't compiler barriers
- riscv64 atomics had broken asm constraints (missing earlyclobber flag)
- arm clone() was broken when compiled as thumb if start function returned
- mipsr6 setjmp/longjmp did not preserve fpu register state correctly
Refreshed all patches.
Removed upstreamed.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Memory auto-detection for mt7621 has just been added to 19.07
stable branch.
This removes the memory node for the ZBT-WE1326, which will support
revision 5 that has 256MiB RAM (Nanya NT5CC128M16IP-DI) instead of
512MiB (up to revision 4).
ref: #1930
This is taken from master commit a2c19f1d2f ("ramips: dts: drop
memory nodes"), where _all_ memory nodes were removed.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
mt7621 has the following memory map:
0x0-0x1c000000: lower 448m memory
0x1c000000-0x2000000: peripheral registers
0x20000000-0x2400000: higher 64m memory
detect_memory_region in arch/mips/kernel/setup.c only add the first
memory region and isn't suitable for 512m memory detection because
it may accidentally read the memory area for peripheral registers.
This commit adds memory detection capability for mt7621:
1. add the highmem area when 512m is detected.
2. guard memcmp from accessing peripheral registers:
This only happens when some weird user decided to change
kernel load address to 256m or higher address. Since this
is a quite unusual case, we just skip 512m testing and return
256m as memory size.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 6d91ddf517)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
