drv_mac80211_teardown fails silently if the device to be torn down is
not defined. This commit prints an error message.
branches affected: trunk, 21.02
Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
When wifi is turned off, drv_mac80211_teardown sometimes fails (silently)
because the device to be torn down is not defined.
This situation arises if drv_mac80211_setup was called twice when
wifi was turned on.
This commit ensures that the device to be torn down is always defined
in drv_mac80211_teardown.
Steps to reproduce:
1) Use /sbin/wifi to turn on wifi.
uci set wireless.@wifi-iface[0].disabled=0
uci set wireless.@wifi-device[0].disabled=0
uci commit
wifi
2) Use /sbin/wifi to turn off wifi.
uci set wireless.@wifi-device[0].disabled=1
uci commit
wifi
3) Observe that wifi is still up.
branches affected: trunk, 21.02
Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
If drv_mac80211_setup is called twice with the same wifi configuration,
then the second call returns early with error HOSTAPD_START_FAILED.
(wifi works nevertheless, despite the fact that setup is incomplete. But
"ubus call network.wireless status" erroneously reports that radio0 is down.)
The relevant part of drv_mac80211_setup is,
if [ "$no_reload" != "0" ]; then
add_ap=1
ubus wait_for hostapd
local hostapd_res="$(ubus call hostapd config_add "{\"iface\":\"$primary_ap\", \"config\":\"${hostapd_conf_file}\"}")"
ret="$?"
[ "$ret" != 0 -o -z "$hostapd_res" ] && {
wireless_setup_failed HOSTAPD_START_FAILED
return
}
wireless_add_process "$(jsonfilter -s "$hostapd_res" -l 1 -e @.pid)" "/usr/sbin/hostapd" 1 1
fi
This commit sets no_reload = 0 during the second call of drv_mac80211_setup.
It is perhaps worth providing a way to reproduce the situation
where drv_mac80211_setup is called twice.
When /sbin/wifi is used to turn on wifi,
uci set wireless.@wifi-iface[0].disabled=0
uci set wireless.@wifi-device[0].disabled=0
uci commit
wifi
/sbin/wifi makes the following ubus calls,
ubus call network reload
ubus call network.wireless down
ubus call network.wireless up
The first and third ubus calls both call drv_mac80211_setup,
while the second ubus call triggers wireless_device_setup_cancel.
So the call sequence becomes,
drv_mac80211_setup
wireless_device_setup_cancel
drv_mac80211_setup
In contrast, when LuCI is used to turn on wifi only a single call
is made to drv_mac80211_setup.
branches affected: trunk, 21.02
Signed-off-by: Bob Cantor <coxede6557@w3boats.com>
CONFIG_CRYPTO_DEV_HIFN_795X depends on PCI. This driver only makes sense on
devices with pci support.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Without loading the igb at boot, the recovery wouldn't have
network available. All network drivers should be loaded before
etc/board.d/02_network is called. Note that other network drivers
already have this set, such as tg3.
Fixes: 7e0e5110bc ("kernel: add igb kernel module")
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Use of WPA3 and things like FILS is getting much more common, and platforms
that can't affort the extra kilobytes for this code are fading away.
Let's not hold back modern authentication methods any longer
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We need to skip sampling if the next sample time is after jiffies, not before.
This patch fixes an issue where in some cases only very little sampling (or none
at all) is performed, leading to really bad data rates
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The removed patches were integrated upstream.
The brcmf_driver_work workqueue was removed in brcmfmac with kernel
5.10.42, the asynchronous call was covered to a synchronous call. There
is no need to wait any more.
This part was removed manually from this patch:
brcm/860-brcmfmac-register-wiphy-s-during-module_init.patch
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add mt7915e dependency on kmod-thermal
22b690334c0f mt76: mt7915: do not fail if the cooling device could not be registered
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The ath patch number is already large and adding other patch for ath11k
will add more confusion with the patch numbering.
Since the support of ath11k based device is imminent, prepare the mac80211
ath patch dir and split it in the dedicated ath5k, ath9k, ath10k and ath11k
(empty for now).
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
bddc1db76d0f mt76: mt7915: drop the use of repeater entries for station interfaces
3c90f35dddac mt76: mt7915: add thermal sensor device support
afab0e8202ff mt76: mt7915: add thermal cooling device support
41cf02184699 mt76: mt7615: add thermal sensor device support
2ac6b8762565 mt76: connac: update BA win size in Rx direction
ddb301127291 mt76: mt7921: fix reset under the deep sleep is enabled
e4cbefd1d69a mt76: mt7921: avoid unnecessary consecutive WiFi resets
393eea2034d7 mt76: mt7921: fix invalid register access in wake_work
a15d46407ffa mt76: mt7921: fix OMAC idx usage
e4d267d8e900 mt76: mt7921: enable runtime pm by default
50fd8ce2412a mt76: connac: add bss color support for sta mode
e29058c3c860 mt76: mt7921: return proper error value in mt7921_mac_init
c89c8c347b1e mt76: mt7921: do not schedule hw reset if the device is not running
9f7bb428e587 mt76: mt7921: reset wfsys during hw probe
22ea365913b5 mt76: mt7915: add .offset_tsf callback
ad91f8e8e494 mt76: mt7615: add .offset_tsf callback
6f871f35e3c1 mt76: mt7915: use mt7915_mcu_get_txpower_sku() to get per-rate txpower
597b68b7daa3 mt76: mt7615: remove useless if condition in mt7615_add_interface()
3945264468eb mt76: testmode: fix memory leak in mt76_testmode_alloc_skb
bdcc57a11606 mt76: testmode: remove unnecessary function calls in mt76_testmode_free_skb
a9763452601d mt76: testmode: remove undefined behaviour in mt76_testmode_alloc_skb
4aef2a2be464 mt76: mt7615: fix potential overflow on large shift
d9dd7635b055 mt76: mt7915: use mt7915_mcu_get_mib_info() to get survey data
d740e921758a mt76: mt7921: introduce mac tx done handling
259ddfc7cb73 mt76: mt7921: update statistic in active mode only
757b93f4b179 mt76: mt7921: remove leftover 80+80 HE capability
1fcff599b2e1 mt76: allow hw driver code to overwrite wiphy interface_modes
c55c22e39b7d mt7915: update firmware to 2020110522
10548aef1f45 mt76: mt7915: improve error recovery reliability
ed6b0c79820c mt76: mt7921: set MT76_RESET during mac reset
321443258bea mt76: move mt76_rates in mt76 module
d1652e8af9e1 Revert "mt76: connac: do not schedule wake_work if the runtime-pm is disabled"
4f4cab39ed9f mt76: mt7915: read all eeprom fields from fw in efuse mode
71450535f164 mt76: mt7921: enable hw offloading for wep keys
833d577e430c mt76: mt7921: remove mt7921_get_wtbl_info routine
67b7a22d2b99 mt76: mt7921: enable random mac address during sched_scan
cf1ff7bf4f1b mt76: mt7915: setup drr group for peers
ef2f7aa8745f mt76: mt7615: update radar parameters
b9f09f530223 mt76: mt7915: fix MT_EE_CAL_GROUP_SIZE
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Some drivers advertise it, but it's not supported at the moment
Reported-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The colon does not directly follow the "VHT Capabilities" string
Reported-by: John Thomson <git@johnthomson.fastmail.com.au>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The name of the module is 'uleds', not 'leds-uleds'.
Signed-off-by: Evgeny Kolesnikov <evgenyz@gmail.com>
[improve commit title]
Signed-off-by: David Bauer <mail@david-bauer.net>
0d5860d fix memory leak in nat46_netdev_destroy().The netdev is forgotten to free in nat46_netdev_destroy function (#26)
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
ATH_REG_DYNAMIC_USER_REG_HINTS is currently not being set as mac80211
tries to set it as m which is not possible as its boolean only.
Since its used alongside user regulatory, move it to USER_REGD.
This is required for ath11k to accept regulatory changes, otherwise
it wont accept any changes and will simply force US.
Signed-off-by: Robert Marko <robimarko@gmail.com>
CONFIG_CRYPTO_DEV_TALITOS depends on FSL_SOC. This driver only makes sense
on Freescale(NXP) SoCs.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
CONFIG_CRYPTO_DEV_GEODE depends on X86_32. This driver only makes sense
on X86\geode.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
CONFIG_CRYPTO_PCOMP and CONFIG_CRYPTO_PCOMP2 have been removed in upstream commit[1].
This symbol doesn't exist since kernel 4.6 and this package is empty.
1. [ crypto: compress - remove unused pcomp interface ]
(110492183c)
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
CONFIG_CRYPTO_WORKQUEUE was removed in upstream commit[1]. This symbol doesn't
exist since kernel 5.3 and this package is empty.
1. [ crypto: cryptd - move kcrypto_wq into cryptd ]
(3e56e16863)
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Adds support for LEDs on input devices. Useful for example on x86 laptops-
allows re-purposing num/caps/scroll lock LEDs.
Signed-off-by: Anderson McKinley <coyoso@tuta.io>
28b162366d09 mt76: fix calling mt76_get_of_eeprom with an offset for pre-cal data
9d736545bb5a mt76: mt7915: disable pre-calibration support for now
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Before this commit, it was assumed that mkhash is in the PATH. While
this was fine for the normal build workflow, this led to some issues if
make TOPDIR="$(pwd)" -C "$pkgdir" compile
was called manually. In most of the cases, I just saw warnings like this:
make: Entering directory '/home/.../package/gluon-status-page'
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
bash: line 1: mkhash: command not found
[...]
While these were only warnings and the package still compiled sucessfully,
I also observed that some package even fail to build because of this.
After applying this commit, the variable $(MKHASH) is introduced. This
variable points to $(STAGING_DIR_HOST)/bin/mkhash, which is always the
correct path.
Signed-off-by: Leonardo Mörlein <me@irrelefant.net>
Includes fix for CVE-2020-24588
c7dd54a22e30 mt76: connac: skip wtbl reset on sta disconnect
3511fd430356 mt76: validate rx A-MSDU subframes
aedc3145de6e mt76: fix possible NULL pointer dereference in mt76_tx
5c2baab92cd0 mt76: mt7615: fix NULL pointer dereference in tx_prepare_skb()
af21659ee834 mt76: mt76x0: use dev_debug instead of dev_err for hw_rf_ctrl
e423c16f16f7 mt76: mt7615: free irq if mt7615_mmio_probe fails
f2d0da8da9b7 mt76: mt7663: enable hw rx header translation
d2713a5d9de9 mt76: mt7921: fix mt7921_wfsys_reset sequence
ce5f32d84f33 mt76: mt7921: Don't alter Rx path classifier
8ab8c7747197 mt76: connac: fw_own rely on all packet memory all being free
a747b0bb4956 mt76: mt7921: enable deep sleep at runtime
2e6e999509b1 mt76: mt7921: add deep sleep control to runtime-pm knob
30bcb2338ce2 mt76: connac: fix WoW with disconnetion and bitmap pattern
56518f4a126e mt76: mt7921: consider the invalid value for to_rssi
e969ab10a034 mt76: mt7921: add back connection monitor support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
From the patch series description:
Several security issues in the 802.11 implementations were found by
Mathy Vanhoef (New York University Abu Dhabi), who has published all
the details at
https://papers.mathyvanhoef.com/usenix2021.pdf
Specifically, the following CVEs were assigned:
* CVE-2020-24586 - Fragmentation cache not cleared on reconnection
* CVE-2020-24587 - Reassembling fragments encrypted under different
keys
* CVE-2020-24588 - Accepting non-SPP A-MSDU frames, which leads to
payload being parsed as an L2 frame under an
A-MSDU bit toggling attack
* CVE-2020-26139 - Forwarding EAPOL from unauthenticated sender
* CVE-2020-26140 - Accepting plaintext data frames in protected
networks
* CVE-2020-26141 - Not verifying TKIP MIC of fragmented frames
* CVE-2020-26142 - Processing fragmented frames as full frames
* CVE-2020-26143 - Accepting fragmented plaintext frames in
protected networks
* CVE-2020-26144 - Always accepting unencrypted A-MSDU frames that
start with RFC1042 header with EAPOL ethertype
* CVE-2020-26145 - Accepting plaintext broadcast fragments as full
frames
* CVE-2020-26146 - Reassembling encrypted fragments with non-consecutive
packet numbers
* CVE-2020-26147 - Reassembling mixed encrypted/plaintext fragments
In general, the scope of these attacks is that they may allow an
attacker to
* inject L2 frames that they can more or less control (depending on the
vulnerability and attack method) into an otherwise protected network;
* exfiltrate (some) network data under certain conditions, this is
specific to the fragmentation issues.
A subset of these issues is known to apply to the Linux IEEE 802.11
implementation (mac80211). Where it is affected, the attached patches
fix the issues, even if not all of them reference the exact CVE IDs.
In addition, driver and/or firmware updates may be necessary, as well
as potentially more fixes to mac80211, depending on how drivers are
using it.
Specifically, for Intel devices, firmware needs to be updated to the
most recently released versions (which was done without any reference
to the security issues) to address some of the vulnerabilities.
To have a single set of patches, I'm also including patches for the
ath10k and ath11k drivers here.
We currently don't have information about how other drivers are, if
at all, affected.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The allows userspace LEDs to be created and controlled. This can be useful
for testing triggers and can also be used to implement virtual LEDs.
Signed-off-by: Keith T. Garner <kgarner@kgarner.com>
[squash fixup commit and improve option wording]
Signed-off-by: Paul Spooren <mail@aparcar.org>
186af01047b2 mt76: mt7921: introduce MCU_EVENT_LP_INFO event parsing
93b5c28c97d5 mt76: mt7921: add rcu section in mt7921_mcu_tx_rate_report
a8e89c5a1d1f mt76: testmode: add support to send larger packet
a0cc9a9e3877 mt76: mt7915: rework mt7915_tm_set_tx_len()
c8b96630324e mt76: mt7915: fix rate setting of tx descriptor in testmode
22fd2958c42a mt76: mt7615: fix memleak when mt7615_unregister_device()
7401e0db3143 mt76: mt7915: fix memleak when mt7915_unregister_device()
c3656268b3f6 mt76: mt7915: only free skbs after mt7915_dma_reset() when reset happens
0ce955b04ba8 mt76: mt7615: only free skbs after mt7615_dma_reset() when reset happens
b03d1e62acf7 mt76: mt7615: use ieee80211_free_txskb() in mt7615_tx_token_put()
5ac02e22fb03 mt76: flush tx status queue on DMA reset
c71f609b398a mt76: sync with upstream changes
23ecadd4af77 mt76: mt7615: fix hardware error recovery for mt7663
57a899ee3c3c mt76: mt7615: fix entering driver-own state on mt7663
42a2dddb706b mt76: mt7615: load ROM patch before checking patch semaphore status
cf0e406af84a mt76: mt7915: add support for applying pre-calibration data
459940ccbc58 mt76: mt7921: move hw configuration in mt7921_register_device
0a094b11f3c0 mt76: improve mcu error logging
bf536832e37d mt76: mt7921: run mt7921_mcu_fw_log_2_host holding mt76 mutex
7616f4f78163 mt76: mt7921: add wifisys reset support in debugfs
e620bd881ef5 mt76: mt7921: abort uncompleted scan by wifi reset
e8dacf59ab1c mt76: mt7915: rework the flow of txpower setting
c8c78e577236 mt76: mt7915: directly read per-rate tx power from registers
1622bf4f8705 mt76: mt7921: add mt7921_dma_cleanup in mt7921_unregister_device
ef96fafad8a9 mt76: Convert to DEFINE_SHOW_ATTRIBUTE
90e4bfea2948 mt76: mt7921: do not use 0 as NULL pointer
0a139d7f5966 mt76: connac: move mcu_update_arp_filter in mt76_connac module
de26c73ce3c2 mt76: mt7921: remove leftover function declaration
1c0b6cb4f942 mt76: mt7921: fix a race between mt7921_mcu_drv_pmctrl and mt7921_mcu_fw_pmctrl
2923e3e2b8e4 mt76: mt7663: fix a race between mt7615_mcu_drv_pmctrl and mt7615_mcu_fw_pmctrl
74d0fdaa7a99 mt76: connac: introduce wake counter for fw_pmctrl synchronization
28c87e09a5ea mt76: mt7921: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx path
36f664edc7db mt76: mt7663: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx path
51b3d1a9a2b7 mt76: dma: add the capability to define a custom rx napi poll routine
4f1339c9fb72 mt76: mt7921: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx/rx napi
1bc5e67a60be mt76: mt7663: rely on mt76_connac_pm_ref/mt76_connac_pm_unref in tx/rx napi
325f7b451c03 mt76: connac: unschedule ps_work in mt76_connac_pm_wake
12115052a02f mt76: connac: check wake refcount in mcu_fw_pmctrl
e5d28e3cef66 mt76: connac: remove MT76_STATE_PM in mac_tx_free
475112a3cdcc mt76: mt7921: get rid of useless MT76_STATE_PM in mt7921_mac_work
112998f32d85 mt76: connac: alaways wake the device before scanning
4334f3e2fc43 mt76: mt7615: rely on pm refcounting in mt7615_led_set_config
0562380659ad mt76: connac: do not run mt76_txq_schedule_all directly
acfa78df5708 mt76: connac: use waitqueue for runtime-pm
ca74a4cd0722 mt76: remove MT76_STATE_PM in tx path
0c2d3e74852e mt76: mt7921: add awake and doze time accounting
45e0eefffe9f mt76: mt7921: enable sw interrupts
fd2ff641166f mt76: mt7615: Fix a dereference of pointer sta before it is null checked
7e2521468767 mt76: mt7921: move mt7921_dma_reset in dma.c
c9dd6b1fa171 mt76: mt7921: introduce mt7921_wpdma_reset utility routine
2ac7c7e9c568 mt76: mt7921: introduce mt7921_dma_{enable,disable} utilities
662a89f2b9d1 mt76: mt7921: introduce mt7921_wpdma_reinit_cond utility routine
614efe9e9180 mt76: connac: introduce mt76_connac_mcu_set_deep_sleep utility
0dbb16ef39d8 mt76: mt7921: enable deep sleep when the device suspends
3c19f569cc70 mt76: mt7921: fix possible invalid register access
ade1f5aad4c6 mt76: move token_lock, token and token_count in mt76_dev
8d5c456be1ff mt76: move token utilities in mt76 common module
fb04d9df5e52 mt76: mt7915: do not read rf value from efuse in flash mode
2126b2176336 mt76: mt7921: get rid of mcu_reset function pointer
d325b7eff1b1 mt76: mt7921: improve doze opportunity
2ae25c7e547e mt76: mt7663: add awake and doze time accounting
349bbb9d6f13 mt76: connac: unschedule mac_work before going to sleep
98a235004dea mt76: mt7921: mt7921_stop should put device in fw_own state
63d80b9ab251 mt76: mt7921: introduce mt7921_mcu_sta_add routine
3c5bf837fdbd mt76: mt7615: fix a precision vs width bug in printk
ded14da5eacc mt76: mt7915: fix a precision vs width bug in printk
aaf0d254f9ea mt76: mt7921: fix a precision vs width bug in printk
757af5c67d32 mt76: move mt76_token_init in mt76_alloc_device
ed41ed73a495 mt76: mt7921: reinit wpdma during drv_own if necessary
92fb81e085c6 mt76: mt7921: fix possible AOOB issue in mt7921_mcu_tx_rate_report
53d915a23bc9 mt76: connac: do not schedule wake_work if the runtime-pm is disabled
23fe1bdcf15a mt76: connac: do not schedule mac_work if the device is not running
e5b19336c58e mt76: mt7615: do not set MT76_STATE_PM at bootstrap
0fc2136a61dd mt76_connac_mcu: move mt76_connac_mcu_update_arp_filter outside of CONFIG_PM
e693f3e23e06 mt76: mt7915: add MSI support
5231e7300fa4 mt7915: disable ASPM
554b50dabf54 mt76: connac: fix uninitialized HT A-MPDU setting field in STA_REC_PHY
43b9c0a838bb mt76: mt7921: fix max aggregation subframes setting
5a387a0a3004 mt76: mt7921: enable rx hw de-amsdu
c8cbcb87be07 mt76: connac: add missing configuration in mt76_connac_mcu_wtbl_hdr_trans_tlv
55921e57b380 mt76: mt7921: enable rx header traslation offload
01441f67d8b2 mt76: mt7921: enable rx csum offload
c9ab76dd93a0 mt76: mt7915: move mt7915_queue_rx_skb to mac.c
caedb4c4ee41 mt76: mt7615: fix fixed-rate tx status reporting
c6ae95d43e6d mt76: improve tx status codepath
27d468d094e6 mt76: mt7915: rework tx rate reporting
3b4ca5b09e2c mt76: mt7615: avoid use of ieee80211_tx_info_clear_status
e1f07d7f1cb9 mt76: mt7603: avoid use of ieee80211_tx_info_clear_status
18513ba5fbc2 mt76: mt7915: add support for tx status reporting
35f189cf81b2 mt76: mt7915: fix uninitialized variable in MSI error handling
9e928ac1ea9b mt76: dma: use ieee80211_tx_status_ext to free packets when tx fails
628eee9c386c mt76: fill queue entry wcid for all skbs with a station
a9bc4d94b7a1 mt76: intialize tx queue entry wcid to 0xffff by default
998ca8af7d17 mt76: mt7915: fix tssi indication field of DBDC NICs
7dd24b3cfacf mt76: mt7915: fix a signedness bug in mt7915_mcu_apply_tx_dpd()
535025d65d8d mt76: mt7915: cleanup mt7915_mcu_sta_rate_ctrl_tlv()
ff8bbe22dd87 mt76: mt7915: add .set_bitrate_mask() callback
Signed-off-by: Felix Fietkau <nbd@nbd.name>
QLCNIC_HWMON was activated when hwmon was set, but the dependency was
missing. This broke the build bot builds. Fix this by explicitly
activating HWMON support and adding a dependency.
Fixes: f88c64d28c ("kernel: netdev: add qlcnic")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This kmod is similar to macvlan with the difference being that the
endpoints have the same mac address.
It is useful on cloud where only one mac address allowed on port,
where macvlan not works but ipvlan would.
One use case is where multiple IPs and gateways assign on one net port
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Missing braces in a macro were leading to badly working rates sometimes
getting a success probabilty of 1.0
Signed-off-by: Felix Fietkau <nbd@nbd.name>
9df230a Zero checksum handling (#25)
7688102 skip generating a UDP4 csum if the UDP6 csum is 0 and zero_csum_pass is set
4a9e4b1 zero csum: avoid calling the checksum adjustment function if udp csum is zero
2de14c5 add a module argument to skip checksum adjust for UDP if checksum is zero
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Select kmod-backlight as dependency for kmod-drm in case kmod-backlight
is compiled.
This fixes kernel 5.10 build issues on x86-geode with all kmods
enabled:
Package kmod-drm is missing dependencies for the following libraries:
backlight.ko
Signed-off-by: David Bauer <mail@david-bauer.net>
CONFIG_MDIO_OF depends on CONFIG_OF which is not enabled for x86.
Fixes builds of x86 with Kernel 5.10 due to unresolved dependencies.
Signed-off-by: David Bauer <mail@david-bauer.net>
As the name suggests, act_gact has the generic actions such as dropping
and accepting packets, so move it into kmod-sched-core.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
CRYPTO_DEV_CCP depends on X86 or ARM64
CRYPTO_DEV_CCP_DD depends on CPU_SUP_AMD or ARM64
Compiling this driver makes sense for x86 mainly. If one day support for
ARM64 board with AMD Secure Processor gets added this package may be
updated.
Trying to build this package on bcm4908 was causing:
ERROR: module 'build_dir/target-aarch64_cortex-a53_musl/linux-bcm4908_generic/linux-5.4.110/drivers/crypto/ccp/ccp-crypto.ko' is missing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
For linux 5.10, kmod-ltq-deu need to be migrated to the new crypto
API/framework.
Leave it in tree for now and enable it only for Kernel 5.4. Maybe
someone picks up the work to migrate the package.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The callback handling of the tasklet API was redesigned and the macros
using the old syntax renamed to _OLD.
The stuck queue is now passed to ndo_tx_timeout callback but not used so
far.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Due to SCHED_FIFO being a broken scheduler model, all users of
sched_setscheduler() are converted to sched_set_fifo_low() upstream and
sched_setscheduler() is no longer exported.
The callback handling of the tasklet API was redesigned and the macros
using the old syntax renamed to _OLD.
Signed-off-by: Mathias Kresin <dev@kresin.me>
ltq tapi
ioremap has provided non-cached semantics by default since the Linux 2.6
days and was removed with kernel version 5.6.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The can-dev.ko kernel module was moved in kernel 5.4.110 and 5.10.28.
Fixes: a1311df95587 ("kernel: bump 5.10 to 5.10.28")
Fixes: b0a34e886d ("kernel: bump 5.4 to 5.4.110")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds monitoring for a couple of DSL line features that are
present in the lantiq firmware blobs.
* G.INP ON/OFF
* Trellis encoding ON/OFF
* Virtaul Noise ON/OFF
* Bitswap ON/OFF
Difference in size for ltq-vdsl-app = 1k
Difference in size for kmod-ltq-vdsl-vr9 < 1k
Reviewed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jeroen Peelaerts <jeroen.peelaerts@gmail.com>
NXP 74HC153 is a GPIO expander. Its original source cide sits in ar71xx
architecture tree. It has been slightly modified to get GPIO pin
configuration from the device tree rather than a MACH file.
Changes to the source file:
- Remove struct nxp_74hc153_config
- in nxp_74hc153_probe(), fetch GPIO configuration from device tree
- allow GPIO framework decide the base number by passing -1 to it
- remove support for kernel versions below 4.5.0
- add OF device compatibility string
Create a package for inclusion in image.
References: https://lore.kernel.org/linux-gpio/545111184.50061.1615922388276@ichabod.co-bxl/
Signed-off-by: Mauri Sandberg <sandberg@mailfence.com>
[added link to driver usptreaming work in progress]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Dependency tracking for kmod-sound-hda-core is fragile. Enabling some sound
codecs (Realtek, Conexant, Sigmatel) implicitly adds a kmod-ledtrig-audio
dependency, while an enabled kmod-ledtrig-audio can be picked up through
enabling others (e.g. kmod-sound-hda-intel), and the behaviour can change
across kernel versions.
As kmod-ledtrig-audio is under 2KB, make it an unconditional dependency.
Fixes: a374b8f190 ("kernel: 5.10: update sound modules")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
With kernel 5.10, exfat is out of staging and in tree.
Added small hack to make it work with kernel 5.4 as well.
Added removed config options for 5.4 to generic config.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[Set CONFIG_EXFAT_ config options to default values]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The link equalizer sch_teql.ko of package kmod-sched relies on a hotplug
script historically included in iproute2's tc package. In previous
discussion [1], consensus was the hotplug script is best located together
with the module in kmod-sched, but this change was deferred at the time.
Relocate the hotplug script now. This change also simplifies adding a tc
variant for minimal size with reduced functionality.
[1] https://github.com/openwrt/openwrt/pull/1627#issuecomment-447923636
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Update file paths for kmod-sound-hda-intel and reflect new dependency of
kmod-sound-hda-core on kmod-ledtrig-audio.
Reported-by: Javier Marcet <javier@marcet.info>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add conditional dependency on kmod-of-mdio due to mdio_devres.c code:
#if IS_ENABLED(CONFIG_OF_MDIO)
...
EXPORT_SYMBOL(devm_of_mdiobus_register);
#endif /* CONFIG_OF_MDIO */
Fixes: 95a3741d17 ("kernel: support new mdio_devres.ko module in 5.10")
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Add kmod-mdio-devres package and kernel config symbol, and update related
kmod-r8169 and kmod-ixgbe package dependencies.
Build tested module dependencies on x86/64 with CONFIG_ALL_KMODS=y.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Make packages depending on usb-serial selective, so we do not have
to add kmod-usb-serial manually for every device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Partially restore the wild-card matching for kmod-usb3 modules to fix
build on platforms without PCI which otherwise file, as seen on
buildbot:
ERROR: module '[...]/linux-5.4.102/drivers/usb/host/xhci-pci.ko' is missing.
modules/usb.mk:1675: recipe for target '[...]/kmod-usb3_5.4.102-1_mips_mips32.ipk' failed
Fixes: 7bda2e9aba ("kernel: fix kmod-usb3 dependencies")
Fixes: be23f9818a ("apm821xx: add support for kernel 5.10")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Adding CONFIG_USB_XHCI_PCI_RENESAS to KCONFIG made it so it was set
for all targets that included kmod-usb3, not just the intended
apm821xx/nand. xhci-pci has a dependency on xhci-pci-renesas if
CONFIG_USB_XHCI_PCI_RENESAS is set, breaking kmod-usb3 builds on
Linux 5.10 on all other targets.
Rework the dependencies by breaking out xhci-hcd, xhci-mtk, and
xhci-pci-renesas into new hidden kernel modules and setting kmod-usb3
dependencies properly.
Tested by building mt7621 and apm821xx/nand with kmod-usb3 on Linux 5.10
Fixes: be23f981 ("apm821xx: add support for kernel 5.10")
Cc: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
This patch copies over refreshed patches from 5.4.
- dropped crypto patches (they got upstreamed)
- dropped renesas USB 3 firmware loader (they got upstreamed)
- NAND now needs extra device-properties for ECC settings.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The QOS feature depends on KPI2UDP which was removed from the tree with
commit a95775e4b2 ("drop unmaintained packages") in 2012.
Since QOS was the last user of the KPI, the feature can be disabled by
default.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The following warnings are shown during build:
/usr/include/vdsl/cmv_message_format.h:33:6: warning: "MEI_SUPPORT_DEBUG_STREAMS" is not defined, evaluates to 0 [-Wundef]
#if (MEI_SUPPORT_DEBUG_STREAMS == 1)
^~~~~~~~~~~~~~~~~~~~~~~~~
/usr/include/vdsl/drv_mei_cpe_interface.h:2256:6: warning: "MEI_SUPPORT_OPTIMIZED_FW_DL" is not defined, evaluates to 0 [-Wundef]
#if (MEI_SUPPORT_OPTIMIZED_FW_DL == 1)
^~~~~~~~~~~~~~~~~~~~~~~~~~~
The headers are provided by the MEI driver, but the defines are never
set by the vdsl app. While the struct with the
MEI_SUPPORT_OPTIMIZED_FW_DL conditional isn't used by the vdsl app,
however CMV_USED_PAYLOAD_8BIT_SIZE which value depends on
MEI_SUPPORT_DEBUG_STREAMS is.
Since the MEI driver doesn't provide an autogenerated header with
compile flags, the flags are hardcoded for the vdsl app.
Set them for the MEI driver as well, to indicate a relation to the
values used for the vdsl app and to be not surprised by a changed
default in case the MEI driver gets updated. Use the current default
values defined in the MEI driver.
Signed-off-by: Mathias Kresin <dev@kresin.me>
CHACHA_MIPS depends on CPU_MIPS32_R2. Therefore,
kmod-crypto-lib-chacha20 should not contain chacha-mips.ko on MIPS32 R1
targets. Enforce that in the target-specific definition.
Fixes bcm47xx, bcm63xx, lantiq/ase, ath25 builds.
Fixes: 06351f1 ("kernel: migrate wireguard into the kernel tree")
Cc: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Use NETWORK_SUPPORT_MENU like all other modules in netsupport.mk. Drop
SECTION and CATEGORY fields as they are set by default and to match
other packages in netsupport.mk. Use better TITLE for kmod-wireguard
(taken from upstream drivers/net/Kconfig).
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
On Linux 5.4, build WireGuard from backports. Linux 5.10 contains
wireguard in-tree.
Add in-kernel crypto libraries required by WireGuard along with
arch-specific optimizations.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Modify existing modules to reflect their new location in Linux 5.10. Add
missing dependenices.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
[enable CRYPTO_USER_API_ENABLE_OBSOLETE; add kmod-crypto-hash dependency
to usb-net-rtl8152]
Signed-off-by: David Bauer <mail@david-bauer.net>
This driver adds the LED support for the PC Engines APU1.
This integrates the Linux kernel driver and includes a patch to support
newer firmware versions. Also the default LED configuration is updated
to use the correct devices.
Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
If an external module uses exported symbols from another external
module, Kbuild needs to have full knowledge of all symbols to
avoid spitting out warnings about undefined symbols.
Use PKG_EXTMOD_SUBDIRS to point to the build directory which contains
the Module.symvers.
Pass KERNEL_MAKE_FLAGS to the external module build, to inject
KBUILD_EXTRA_SYMBOLS. KBUILD_EXTRA_SYMBOLS holds a space separated list
of Module.symvers, which list all exported symbols.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Let's switch to 5.10 now that mac80211 has been updated.
Runtime-tested on ipq806x (Netgear R7800).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
When transmitting to a receiver in dynamic SMPS mode, all transmissions that
use multiple spatial streams need to be sent using CTS-to-self or RTS/CTS to
give the receiver's extra chains some time to wake up.
This fixes the tx rate getting stuck at <= MCS7 for some clients, especially
Intel ones, which make aggressive use of SMPS.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
On hardware that supports this, this will improve performance by passing
802.3 frames from the hardware to the stack
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The removed patches were applied upstream.
This adapts ath10k-ct and mt76 to changed APIs.
nl80211.h in iw is updated to match the version from backports.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The removed patches were applied upstream.
Remove the 300-mac80211-optimize-skb-resizing.patch.
This patch was not applied upstream, but it conflicts with upstream
changes and needs bigger changes. It was applied with Felix to remove
this patch for now. It should be reworked and then send upstream later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
After looking at various vendor GPL source code dumps I discovered that some
of them contain updated versions of ltq-ptm driver when compared to what
openwrt has.
The driver update is mostly cursory (simple changes to comments, whitespace,
formatting etc.) or adds debug features not used by openwrt.
However the updated driver also contains a later version of PTM firmware which
is extracted and included in this commit along with bits to correctly identify
its version when driver loads.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
erley.org no longer exists; attempting to connect to it during package
download results in lengthy timeouts. Use the new OpenWrt CDN alias to
download from reliable OpenWrt mirrors.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Multiple sources are hosted on OpenWrts source server only. The source
URLs to point to the server vary based on different epochs in OpenWrts
history.
Replace all by @OPENWRT which is an "empty" mirror, therefore using the
fallback servers sources.cdn.openwrt.org and sources.openwrt.org.
Signed-off-by: Paul Spooren <mail@aparcar.org>
If the driver uses .sta_add, station entries are only uploaded after the sta
is in assoc state. Fix early station rate table updates by deferring them
until the sta has been uploaded
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Enable support for the Ubiquiti UniFi Outdoor+ RF filter via
device-tree. The old way of using platform data is not required anymore,
as it was only used on the now removed ar71xx target.
Signed-off-by: David Bauer <mail@david-bauer.net>
Changelog:
- ath10k-ct: Pull in some upstream patches.
Runtime-tested on ipq806x (Netgear R7800).
Signed-off-by: Michael Yartys <michael.yartys@gmail.com>
65abbcd9f6fb mt76: usb: process URBs with status EPROTO properly
3199ef5fa35e mt76: mt7615: set mcu country code in mt7615_mcu_set_channel_domain()
5c86d5bb079b mt76: mt7915: Remove unneeded semicolon
3f546330b59d mt76: mt7915: support TxBF for DBDC
032ad7e02545 mt76: mt7615: unify init work
cc3f23d1e654 mt76: mt7915: bring up the WA event rx queue for band1
fa3d334a0e22 mt76: fix crash on tearing down ext phy
c4c9c402d14a mt76: mt7915: fix vif sta index for DBDC
eca2f0ec0d4c mt76: mt7915: fix command id for txbf action
c828124ef9a5 mt76: mt7915: add support for using a secondary PCIe link for gen1
dbaf0f4679f3 mt76: mt7915: make vif index per adapter instead of per band
fb3e5ce1eb00 mt76: move vif_mask back from mt76_phy to mt76_dev
be2bea66d6e3 mt76: mt7915: detect wrong nss eeprom parameter on dbdc cards
8dc5d4a0da7c Revert "mt76: mt7915: fix vif sta index for DBDC"
8c796a33781c mt76: mt7915: only set int1 when using the second hif
4eb5caaf6cc1 mt76: reduce q->lock hold time
0714890bf0fd mt76: mt7615: reduce VHT maximum MPDU length
2f85aa5cbc62 mt76: mt7915: avoid writes to MT_PCIE_RECOG_ID when not using gen1 devices
8696919d9aae mt76: dma: fix a possible memory leak in mt76_add_fragment()
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The following four led triggers are enabled in generic config.
* kmod-ledtrig-default-on
* kmod-ledtrig-heartbeat
* kmod-ledtrig-netdev
* kmod-ledtrig-timer
Drop the packages and remove them from DEVICE_PACKAGES.
There's no other package depending on them in this repo.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
CONFIG_THERMAL option was changed to boolean in upstream linux commit
554b3529fe01 ("thermal/drivers/core: Remove the module Kconfig's option").
Switch it to 'y' and remove FILES and AUTOLOAD for non-existant module file.
And update the descripton text for the package as in upstream linux commit
eb8504620381 ("thermal: Rephrase the Kconfig text for thermal").
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
a46f9a9160e9 mt76: mt7915: add vif check in mt7915_update_vif_beacon()
27ad12352ac9 mt76: mt7615: add vif check in mt7615_update_vif_beacon()
0a449cef024e mt76: mt7915: fix MT_CIPHER_BIP_CMAC_128 setkey
eacd2d493c61 mt76: mt7915: reset token when mac_reset happens
e4b23301e6c9 mt76: mt7615: reset token when mac_reset happens
6e22bbfe0360 mt76: mt7615: convert comma to semicolon
37865118ae2d mt76: mt7915: convert comma to semicolon
742c36b2e527 mt76: mt7915: run mt7915_configure_filter holding mt76 mutex
a515727e8423 mt76: mt7915: add support for flash mode
b6f7b3da5216 mt76: mt7915: fix endianness warning in mt7915_mcu_set_radar_th
062f3f4f06a2 mt76: mt7915: simplify mt7915_mcu_send_message routine
dbba9b993300 mt76: mt7915: drop zero-length packet to avoid Tx hang
36a745d0f71c mt76: Fix queue ID variable types after mcu queue split
a4539760b0b1 mt7915: update the testmode support to the latest upstream patch
64bd6f87e4c2 mt7915: fix crash on failure in pci_set_dma_mask
c202ace409e0 mt76: remove unused variable q
d1b827781f84 mt76: mt7915: add partial add_bss_info command on testmode init
a897a69769f5 mt76: testmode: introduce dbdc support
b44472e99822 mt76: testmode: move mtd part to mt76_dev
45e27e6cdc12 mt76: mt7915: move testmode data from dev to phy
b6673b005770 mt76: mt7615: move testmode data from dev to phy
abdd471e9f2d mt76: mt7915: fix ht mcs in mt7915_mcu_get_rx_rate()
d679b56b9585 mt76: move mac_work in mt76_core module
36cd48ab4454 mt76: move chainmask in mt76_phy
89a6781ed045 mt76: mt7915: force ldpc for bw larger than 20MHz in testmode
3d0834e78005 mt76: testmode: add support to set user-defined spe index
cc05f4679667 mt76: testmode: add attributes for ipg related parameters
77b18b16fe16 mt76: testmode: make tx queued limit adjustable
6365a58573cb mt76: mt7915: split edca update function
e56282bf67f6 mt76: mt7915: add support for ipg in testmode
6fa642903e4e mt76: mt7915: calculate new packet length when tx_time is set in testmode
729ec5daeba5 mt76: mt7915: clean hw queue before starting new testmode tx
981443da5cf7 mt76: testmode: add a new state for continuous tx
4793fc9b3d48 mt76: mt7915: rework set state part in testmode
11a1e86e5946 mt76: mt7915: add support for continuous tx in testmode
364affef82fc mt76: mt7615: mt7915: disable txpower sku when testmode enabled
9fc19db51293 mt76: mt7915: simplify peer's TxBF capability check
6377b7f330be mt76: mt7915: add implicit Tx beamforming support
983091a40633 mt76: mt7915: fix MESH ifdef block
bbb7a9e77751 mt76: mt76u: fix NULL pointer dereference in mt76u_status_worker
a28a8dd2f7de mt76: usb: fix crash on device removal
9c312f2ce2c5 mt76: mt7915: rework mcu API
e6fe82acb111 mt76: mt7915: disable RED support in the WA firmware
25d7429bdc41 mt76: mt7915: fix eeprom parsing for DBDC
7a93026dd3dc mt76: mt7915: fix eeprom DBDC band selection
4c8a09cc45d0 tools: Set mode for new file /tmp/mt76-test-%s
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This allows libnetfilter_queue to access connection tracking information
by requesting NFQA_CFG_F_CONNTRACK. Connection tracking information is
provided in the NFQA_CT attribute.
CONFIG_NETFILTER_NETLINK_GLUE_CT enables the interaction between
nf_queue and nf_conntrack_netlink. Without this option, trying to access
connection tracking information results in "Operation not supported".
Signed-off-by: Etan Kissling <etan_kissling@apple.com>
This patch adds kernel module for Silicon Labs CP2112 HID USB to SMBus
Master Bridge. This is a HID device driver which registers as an i2c
adapter and gpiochip to expose these functions of the CP2112.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This patch adds wil6210 driver for Wilocity/QCA based 802.11ad
PCI cards.
Driver uses cfg80211 and nl80211 but not mac80211.
Integration for UCI and LuCI will come in other patches.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Legacy minstrel is essentially unmaintained and was showing poor performance
Replace it with minstrel_ht and improve rate selection and sampling behavior
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since we're now able to select CONFIG_NET_UDP_TUNNEL at will, drop the fake
dependencies.
This is a partial revert of commit d7e040f8bc
"kernel: add fake users for udptunnel and iptunnel modules".
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This patch bumps cryptodev-linux to the latest stable release (1.11) and fixes
compilation against the next LTS (and likely OpenWrt) kernel 5.10.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Since generic has the option set to y and other targets now inherit that
choice, there is no behaviour change
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
As of hostapd upstream commit 7d2ed8ba "Remove CONFIG_IEEE80211W build parameter"
https://w1.fi/cgit/hostap/commit?id=7d2ed8bae86a31dd2df45c24b3f7281d55315482
802.11w feature is always enabled in the build time.
It doesn't make sense to opt-in 802.11w per driver as hostapd will always
be compiled with this feature enabled.
As suggested by Hauke Mehrtens, for now keep 11w enabled in build_features.h
for compatibility reasons. This option will be dropped when LuCI is adjusted.
Signed-off-by: Dobroslaw Kijowski <dobo90@gmail.com>
Testing with hwsim reveals two problems:
1. phyX/addresses has two addresses and mac80211_get_addr keeps
returning the last one when asked for more;
2. The base address has the local bit set and the operation unsets it.
Fix both.
Fixes: 866790fd82
Reported-by: Zero_Chaos
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
0fdfef9aa7ee68ddd508aef7c98630cfc054f8d6 upstream removed CIFS_SMB311.
Kernels 4.19 and above do not have it. Currently only kernels 4.19 and
5.4 are in the tree.
The Kconfig file in the kernel has more selection that what is in here.
Add the rest and reorder based on upstream ordering.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
7f53d68b1af9 mt76: mt7615: add debugfs knob for setting extended local mac addresses
1a2547b27dfc mt76: do not set NEEDS_UNIQUE_STA_ADDR for 7615 and 7915
2741fd071bb7 mt76: mt7915: support 32 station interfaces
709f2cd77810 mt76: mt7915: fix processing txfree events
434940e08233 mt76: mt7915: measure channel noise and report it via survey
236326896589 mt76: mt7615: retry if mt7615_mcu_init returns -EAGAIN
b5c593b63f4c mt76: mt7663s: move tx/rx processing in the same txrx workqueue
75157b59ae4e mt76: mt7663s: convert txrx_work to mt76_worker
6dc67b058e2a mt76: mt7663s: disable interrupt during txrx_worker processing
b381729626bb mt76: sdio: convert {status/net}_work to mt76_worker
9cb12f7042cc mt76: mt7915: fix DRR sta bss group index
75977a85e844 mt76: mt7915: disable OFDMA/MU-MIMO UL
6cdebe805862 mt76: rename __mt76_mcu_send_msg to mt76_mcu_send_msg
eb9afae96b65 mt76: rename __mt76_mcu_skb_send_msg to mt76_mcu_skb_send_msg
8c73f3b15ada mt76: implement .mcu_parse_response in struct mt76_mcu_ops
fcfbb046c2f3 mt76: move mcu timeout handling to .mcu_parse_response
477caa196ffe mt76: move waiting and locking out of mcu_ops->mcu_skb_send_msg
a4d71501bad6 mt76: make mcu_ops->mcu_send_msg optional
80c310c59ad1 mt76: mt7603: switch to .mcu_skb_send_msg
082b26181013 mt76: implement functions to get the response skb for MCU calls
ee40800df2e4 mt76: mt7915: move eeprom parsing out of mt7915_mcu_parse_response
d33943baac47 mt76: mt7915: query station rx rate from firmware
b8874e8756d9 mt76: add back the SUPPORTS_REORDERING_BUFFER flag
633ae5961db6 mt76: mt7615: enable beacon filtering by default for offload fw
9a203fea3540 mt76: mt7615: introduce quota debugfs node for mt7663s
f9ae638af7e2 mt76: mt7663s: get rid of mt7663s_sta_add
1a5758d894d0 mt76: mt7663s: fix a possible ple quota underflow
dea10c03316f mt76: sdio: get rid of sched.lock
eb4c09957938 mt76: mt7915: set fops_sta_stats.owner to THIS_MODULE
594890b11155 mt76: mt7915: update ppe threshold
8884a5def518 mt76: mt7915: rename mt7915_mcu_get_rate_info to mt7915_mcu_get_tx_rate
33b89f4a1bf4 mt76: set fops_tx_stats.owner to THIS_MODULE
4d019c9672ec sync with upstream changes
35e3cd1db479 mt76: mt7603: fix ED/CCA monitoring with single-stream devices
4f9f79b085b1 wireless: mt76: convert tasklets to use new tasklet_setup() API
20e8cf935ed0 mt76: dma: fix possible deadlock running mt76_dma_cleanup
36089a655f58 mt76: mt7915: fix sparse warning cast from restricted __le16
68c4eedafd61 mt76: fix memory leak if device probing fails
9a1a0a4dec71 mt76: mt7603: add additional EEPROM chip ID
01b943295719 mt76: move mt76_mcu_send_firmware in common module
0aee4999902a mt76: mt7663s: introduce WoW support via GPIO
79ebad117325 mt76: switch to wep sw crypto for mt7615/mt7915
af139725193a mt76: fix tkip configuration for mt7615/7663 devices
664e66b35c0b mt76: mt7615: run key configuration in mt7615_set_key for usb/sdio devices
f675358267d6 mt76: mt76u: rely on woker APIs for rx work
b9f9c16cb1bd mt76: mt76u: use dedicated thread for status work
cdeb1b29cd15 mt76: testmode: switch ib and wb rssi to array type for per-antenna report
0a898c0549b6 mt76: testmode: add snr attribute in rx statistics
3ea9a0433bcc mt76: testmode: add tx_rate_stbc parameter
73427ebbbd27 mt76: testmode: add support for LTF and GI combinations for HE mode
88ebccfe8a39 mt76: mt7915: fix tx rate related fields in tx descriptor
9909c0551e4c mt76: testmode: add support for HE rate modes
03ed0909f922 mt76: mt7915: implement testmode tx support
0aa696834a9c mt76: mt7915: implement testmode rx support
5ed3a34b46ce mt76: mt7915: add support to set txpower in testmode
f86361654e94 mt76: mt7915: add support to set tx frequency offset in testmode
64a765be750a mt76: mt7915: make mt7915_eeprom_read static
9b48c13b52f7 mt76: mt7915: use BIT_ULL for omac_idx
27227fd57ea7 mt76: mt7915: remove unused mt7915_mcu_bss_sync_tlv()
cd795267612d mt76: mt7615: support 16 interfaces
82da525ad0c8 mt76: mt7615: refactor usb/sdio rate code
b9a50da503ad mt76: mt7915: rely on eeprom definitions
c79d18723df0 mt76: move mt76_init_tx_queue in common code
b0b221e91445 mt76: sdio: introduce mt76s_alloc_tx_queue
caba5a99e5ae mt76: sdio: rely on mt76_queue in mt76s_process_tx_queue signature
3ed4aad81ce9 mt76: mt7663s: rely on mt76_queue in mt7663s_tx_run_queue signature
216cf8b28579 mt76: dma: rely on mt76_queue in mt76_dma_tx_cleanup signature
0f9350bef1b5 mt76: rely on mt76_queue in tx_queue_skb signature
8932975be066 mt76: introduce mt76_init_mcu_queue utility routine
b0eb7edcc624 mt76: rely on mt76_queue in tx_queue_skb_raw signature
ccd62467d0f3 mt76: move mcu queues to mt76_dev q_mcu array
2e217fb9e962 mt76: move tx hw data queues in mt76_phy
576647f2ec6a mt76: mt7915: fix endian issues
e881fd67c718 mt76: move band capabilities in mt76_phy
c728cecd7b77 mt76: rely on mt76_phy in mt76_init_sband_2g and mt76_init_sband_5g
231ef27697f9 mt76: move band allocation in mt76_register_phy
8aa24c91b13b mt76: move hw mac_addr in mt76_phy
b436da4d9d92 mt76: mt7915: introduce dbdc support
1e34a02c2dcb mt76: mt7915: get rid of dbdc debugfs knob
d8e681bd3268 mt76: mt7615: fix rdd mcu cmd endianness
19c9e277eff6 mt76: mt7915: fix memory leak in mt7915_mcu_get_rx_rate()
e361b6a71e4b mt76: improve tx queue stop/wake
fb24e5f2305b mt76: mt7915: stop queues when running out of tx tokens
066cc441eb8f mt76: attempt to free up more room when filling the tx queue
93c806a34ec2 mt7915: fix minor issues in the token queue blocking change
c017e329a326 mt76: mt7915: ensure that init work completes before starting the device
9e9da427b8a6 mt76: mt7915: fix polling firmware-own status
5cd805ddfb25 mt76: add more conditions for stopping tx scheduling
aa893c73bf85 mt76: mt7915; increase txq memory limit for non-DBDC 7915 cards to 32 MiB
e44b7c91070e mt76: skip queue stop/wake, rely entirely on txq scheduling
6c6a5c59c101 mt76: mt7915: do not set DRR group for stations
510cb5be1bf7 mt76: usb: remove wake logic in mt76u_status_worker
34f318a25421 mt76: sdio: remove wake logic in mt76s_process_tx_queue
4a90fdf6105e mt76: mt76s: fix NULL pointer dereference in mt76s_process_tx_queue
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The PKG_MIRROR_HASH was not updated when updating the package.
Fixes: f75c70aeca ("nat46: update to latest git HEAD")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This add support for USB-to-Ethernet Aquantia AQtion
5/2.5GbE adapters based on the AQC111U controllers.
Run-tested: x86
Adapter-tested: Sabrent NT-SS5G
Signed-off-by: Marty Jones <mj8263788@gmail.com>
Zstd is supported by the crypto API since Linux 4.18. Enable this feature and
reveal the package in the configuration section, so the user can select it.
This allows zstd to be used as a compression algorithm in zram, for example.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
I've just noticed on i.mx6 target, that there are missing kernel symbols
so I'm fixing it.
Fixes: 3c5d70ad26 ("kernel: add module support Solarflare network adapter")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Since we are using mac80211 5.8, let's also switch the ath10k-ct driver
to the new 5.8 version.
Modify patches so they patch the new ath10k-ct driver version.
Adapt 164-ath10k-commit-rates-from-mac80211.patch.
Drop upstreamed 205-ath10k-Add-NL80211_EXT_FEATURE_AQL-flag.patch.
Drop the other options for CT_KVER from the comment, as it is incorrect
and there are too many versions to sum up and maintain there.
Runtime-tested on ath79 (D-Link DAP-2695-A1, TP-Link EAP245-v3).
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
All targets that used mvsw61xx have switched to upstream mv88e6xxx DSA
driver, so it can be removed.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
This change adds the configuration option to build and include
the nft_queue kernel module, which allows traffic to be queued up
to userspace from an nftables rule
Tested-by: Sébastien Delafond sdelafond@gmail.com
Signed-off-by: Brett Mastbergen <bmastbergen@untangle.com>
Remove deferred sampling code which does not work well with rate tables +
probing.
Fix tx status handling if the first invalid rate idx is not set to -1
Signed-off-by: Felix Fietkau <nbd@nbd.name>
A lot of devices running OpenWrt x86 arch (32 or 64 bit) are either
"home-made routers" or devices that use PC class OEM components.
This commit enables OEM cards support on those devices by default.
Signed-off-by: Rafał Dzięgiel <rafostar.github@gmail.com>
[reformat commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
This removes switches dependent on kernel version 4.19 as well as
several packages/modules selected only for that version.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This reverts commit 7f94e2afcf.
Package kmod-nft-core is missing dependencies for the following libraries:
nft_reject.ko
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
If mac80211_setup_supplicant() is called with enabled=0 then it should just
destroy the interface and remove the configuration from wpa_supplicant. But
the ubus method call always returned
Command failed: Method not found
because the actual name of the method is "config_remove".
Fixes: b5516603dd ("mac80211: more wifi reconf related fixes")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[bump PKG_RELEASE]
Signed-off-by: David Bauer <mail@david-bauer.net>
hostapd_set_bss_options expects the PHY as second and the VIF as third
argument. However, only the VIF was passed as second argument without a
third argument at all.
This was never a problem, as both PHY and VIF were never accessed.
However, with FTM support the PHY is needed to determine the HW support
when configuring the BSS.
Signed-off-by: David Bauer <mail@david-bauer.net>
rt2800 olny gives you survey for current channel.
Survey-based ACS algorithms are failing to perform their job when working
with rt2800.
Make rt2800 save survey for every channel visited and be able to give away
that information.
There is a bug registred https://dev.archive.openwrt.org/ticket/19081 and
this patch solves the issue.
Signed-off-by: Markov Mikhail <markov.mikhail@itmh.ru>
After the status rework, ieee80211_tx_status_ext is leaking un-acknowledged
packets for stations in powersave mode.
To fix this, move the code handling those packets from __ieee80211_tx_status
into ieee80211_tx_status_ext
Reported-by: Tobias Waldvogel <tobias.waldvogel@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Size of the modules for a Cortex A7 build:
43920 linux-5.4.66/sound/soc/codecs/snd-soc-spdif-rx.ko
44044 linux-5.4.66/sound/soc/codecs/snd-soc-spdif-tx.ko
Signed-off-by: Andre Heider <a.heider@gmail.com>
This option is now activated in the generic kernel configuration, no
need to do it for a specific package.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This config option was moved to the generic kernel configuration.
Fixes: ab1bd57656 ("kernel: move F2FS_FS_XATTR and F2FS_STAT_FS symbols to generic")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
