We should setup the registers for trapping LLDP packets to the CPU.
Currently, these packets are forwarded to all ports which is not desired
behaviour.
Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
These registers control the handling of Link Layer Discovery Protocol
(LLDP) packets. This seems to be a typo in the naming.
Signed-off-by: Kevin Jilissen <info@kevinjilissen.nl>
This includes multiple updates for BCM2711 and BCM2712.
Full changelog:
0968de2871...1.20240424
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Newer compilers default to building with C++17 as default, which has the
register keyword removed and thus errors.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This device is similiar to the Wavlink WL-WN531A3.
Hardware
--------
SoC: Mediatek MT7620A
RAM: 64MB
FLASH: 8MB NOR (GigaDevice GD25Q64CS)
ETH:
- 2x 10/100/1000 Mbps Ethernet (RTL8211F)
- 3x 10/100 Mbps Ethernet (integrated in SOC)
WIFI:
- 2.4GHz: 1x (integrated in SOC) (2x2:2)
- 5GHz: 1x MT7612E (2x2:2)
- 4 external antennas
BTN:
- 1x Reset button
- 1x Touchlink button
- 1x Turbo button
- 1x Wps button
- 1x ON/OFF switch
LEDS:
- 1x Red led (system status)
- 1x Blue led (system status)
- 5x Blue leds (ethernet ports)
- 1x Power led
- 1x Wifi led
UART:
- 57600-8-N-1
Everything works correctly.
Installation
------------
Flash the initramfs image in the OEM firmware interface
When Openwrt boots, flash the sysupgrade image otherwise you won't be
able to keep configuration between reboots.
In my case the whole device was locked and there was no way
to flash the image, except for flashing directly to the flash
via an spi-flasher. You need to put the sysupgrade image file at
the beginning of 0x60000.
Notes
-----
1) Router mac addresses:
LAN XX:XX:XX:XX:XX:F0 (factory @ 0x28)
WAN XX:XX:XX:XX:XX:F1 (factory @ 0x2e)
WIFI 2G XX:XX:XX:XX:XX:F2 (factory @ 0x04)
WIFI 5G XX:XX:XX:XX:XX:F3 (factory @ 0x8004)
LABEL XX:XX:XX:XX:XX:F2
Signed-off-by: Eros Brigmann <erosbrigmann@gmail.com>
All kernel config files are refreshed by
`make kernel_oldconfig CONFIG_TARGET={subtarget_target,subtarget}`
"CONFIG_SQUASHFS_DECOMP_SINGLE=y" is manually selected as all ath79
SoCs are single core processors.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The upcoming 6.6 kernel will introduce a new upstream generic
"gpio-latch" driver. It will conflict with the downstream MikroTik
GPIO latch driver. Let's rename it to avoid any potential issues.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Hardware:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 128 MiB SPI NAND
- RAM: 512 MiB
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN, 802.11ax)
- Ethernet: 1x 10/100/1000/2500 Mbps RTL8221B WAN, 1x10/100/1000 Mbps MT7981 LAN
- USB 3.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Serial console: internal test points, 115200 8n1
- Power: 5 VDC, 3 A
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x1 | label+1 |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 82:af:ca:xx:xx:x0 | |
+---------+-------------------+-----------+
Installation:
The installation must be done via TFTP by disassembling the router. On other occasions Cudy has distributed intermediate firmware to make installation easier, and so I recommend checking the Wiki for this device if there is a more convenient solution than the one below.
To install using TFTP:
1. Connect to UART.
2. With the router off, press the RESET button. While the router is turning on, the button should continue to be pressed for at least 5 seconds.
3. A u-boot shell will automatically open.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP server and an OpenWrt initramfs-kernel.bin firmware file.
5. Run these steps in u-boot using the name of your file.
setenv bootfile initramfs-kernel.bin
tftpboot
bootm
6. If you can reach LuCI or SSH now, just use the sysupgrade image with the 'Keep settings' option turned off.
Signed-off-by: Luis Mita <luis@luismita.com>
Hardware Specification:
SoC: Mediatek MT7621DAT (MIPS1004Kc 880 MHz, dual core)
RAM: 128 MB
Storage: 128 MB NAND flash
Ethernet: 5x 10/100/1000 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
Wireless: 2.4GHz: Mediatek MT7603EN up to 300Mbps (802.11b/g/n MIMO 2x2)
Wireless: 5GHz: Mediatek MT7615N up to 1733Mbps (802.11n/ac MU-MIMO 4x4)
LEDs: Power (white & amber), Internet (white & amber)
LEDs: 2.4G (White), 5Ghz (White)
Buttons: WPS, Reset
MAC Table
Label xx:xx:xx:xx:xx:EB
LAN xx:xx:xx:xx:xx:EB
2.4Ghz xx:xx:xx:xx:xx:EC
5Ghz xx:xx:xx:xx:xx:ED
WAN xx:xx:xx:xx:xx:EE
Flash instructions:
D-Link normal OEM firmware update page
1. upload OpenWRT factory.bin like any D-Link upgrade image
D-Link Recovery GUI:
1. Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
2. Give it ~30 seconds, to boot the recovery mode GUI
3. Connect your client computer to LAN1 of the device
4. Set your client IP address manually to 192.168.0.2 / 255.255.255.0
5. Call the recovery page for the device at http://192.168.0.1/
6. Use the provided emergency web GUI to upload the recovery.bin to the device
Firefox on Windows in a Private Window (incognito) works me
Internet Explorer mode in Microsoft Edge works for others
seems to not work in Linux or virtual machine on Linux for most
some see success using 'curl -v -i -F "firmware=@file.bin" 192.168.0.1'
Thanks to @frkca and @rodneyrod for testing and pushing for its creation
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
Setting the LED name and abandoning the label and using the
function/color syntax for some TP-Link Archer series routers:
Archer C2 v1, Archer C20 v1, Archer C20i and Archer C50 v1
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Abandoning the label and using the function/color syntax for some dlink
dir series routers: dir-1960-a1, dir-2660-a1, dir-2640-a1, dir-3040-a1
and dir-3060-a1
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Rename from mt7621_dlink_dir-xx60-a1.dtsi to mt7621_dlink_dir_nand_128m.dtsi
and associated group name when creating the mt7621.mk image
Co-authored-by: Alan Luck <luckyhome2008@gmail.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Continuation of commit 8b66f1a. Set the switch address on the MDIO bus to 31.
This is required for all boards currently working with the mt7530 DSA driver.
Fixes: #15419
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
don't mention SHA1 in order to not confuse users - SHA1 support is already disabled (except RSA-SHA1 signagures).
ref: https://github.com/openwrt/openwrt/issues/15281
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
- update dropbear to latest stable 2024.85;
for the changes see https://matt.ucc.asn.au/dropbear/CHANGES
- drop cherry-picked patches (merged in release 2024.84)
- refresh remaining patches
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Konstantin Demin <rockdrilla@gmail.com>
Backport patch merged upstream for rgmii-id support in stmmac-ipq806x.
This is needed for some device that directly connets PHY to the gmac
port and require rgmii-id phy-modes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
New:
- mold is now up to 10% faster when linking very large, debug
info-enabled executables such as Blender (~1.8 GiB) or Clang (~3.8
GiB), thanks to several improvements we've made to the string merging
algorithm. (53ebcd8, d714301, 40f6b17, c9faf3d)
- -z start-stop-visibility=hidden is now supported so that
linker-synthesized __start_<section-name> and __stop_<section-name>
symbols can be completely hidden from other ELF modules. Previously,
only -z start-stop-visibility=protected was supported. (99a5b15)
- -Bsymbolic-non-weak and -Bsymbolic-non-weak-functions options are now
supported for compatibility with LLVM lld. Just like lld, these options
control which symbols are exported as dynamic symbols.
-Bsymbolic-non-weak makes the linker to export only weak symbols,
whereas -Bsymbolic-non-weak-functions makes it to export only weak
function symbols. (7d17aa8)
Bug fixes and compatibility improvements:
- Previously, if a linker script contains a newline character in the
beginning four bytes of a file, it was not recognized as a linker
script by mold. Now, mold allows newlines at the beginning of a file.
(ea054cc)
- Under rare circumstances, the INPUT linker script command may have
found a different file than GNU ld would. Now, mold's behavior aligns
with GNU ld's. (163975d)
- Previously, the --repro option produced corrupted tar files. Now the
bug has been fixed. (32c4a09)
- mold generally guarantees that its output is reproducible, meaning that
if you run the linker with the exact same command line options and
input files, the output is guaranteed to be bit-for-bit identical to
the previous outputs. However, under rare circumstances, it might
produce different output due to a bug. It's reported that this
nondeterminism caused random crashes for some programs (#1247). This
bug has been fixed. (6463a7c)
- mold no longer sets the address of the .text section as the entry point
address if --entry option is not given, just like LLVM lld. (020b1a7)
- [RISC-V] __global_pointer$ symbol is now exported from executables as
required by the processor-specific ABI. (3df7c8e)
- [ARM32] --long-plt option is now recognized as known option by mold.
mold ignores the option, though, because the PLTs generated by our
linker is always long. (d432e98)
Release Notes:
https://github.com/rui314/mold/releases/tag/v2.31.0
Signed-off-by: Sean Khan <datapronix@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/15403
Signed-off-by: Robert Marko <robimarko@gmail.com>
WPJ419 is still manually defining SPI node, so lets
convert it to use the existing upstream labels for SPI node.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
WPJ419 is still manually defining pinctrl node, so lets
convert it to use the existing upstream labels for pinctrl node.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
WPJ419 is still manually defining PCIe node, so lets
convert it to use the existing upstream labels for PCIe node and while we
are here use the -gpios suffix instead.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some boards are still defining MDIO nodes under soc instead of using the
existing upstream labels to reference them so convert them.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some boards are still defininig I2C nodes under soc instead of using the
existing upstream labels to reference them so convert them.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some boards are still defininig UART nodes under soc instead of using the
existing upstream labels to reference them so convert them.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
This device does not have NAND enabled at all and NAND is the only consumer
of QPIC BAM DMA, so drop the node.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
WPJ419 is still manually defining dma nodes(And even some labels), so lets
convert it to use the existing upstream labels for DMA nodes.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, a lot of boards are still not using the existing label to
reference the crypto node, so lets rectify this.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, a lot of boards are still not using the existing label to
reference the prng node, so lets rectify this.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
Currently, a lot of boards are still not using the existing label to
reference the watchdog node, so lets rectify this.
Link: https://github.com/openwrt/openwrt/pull/15415
Signed-off-by: Robert Marko <robimarko@gmail.com>
The 'nandbiterrs' tool is useful to find out of bit error correction of
NAND is working as expected by deliberately introducing bit errors and
telling up to which number they can be corrected.
Enable build of the testing tools and package the 'nandbiterrs' tool as
part of the nand-utils package.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The way to register the switch MDIO bus and PHYs on the bus in upstream
Linux is more strict and requires each PHY to explicitely state the
interrupt instead of assuming it in case the 'interrupts' property in DT
is missing.
Add missing interrupts for the PHYs of the build-in 4x1GE switch of the
MT7988 SoC.
Fixes: 4354b34f6f ("generic: 6.6: sync mt7530 DSA driver with upstream")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
To fix issue #15304
Correct br-lan ports 1-4 so that phy-handle matches reg nr not port label.
Fixes: eb13076e77 ("mediatek: fix DTS defining mt7530 switch phys but not referencing them")
Signed-off-by: Magnus Lindström <magnus1089@hotmail.com>
The Gemini works fine with kernel v6.6.
As per the example for ipq806x, drop support for anything
older than v6.6, there is no point in supporting it,
and the new DTS SoC directory just makes it hard to
maintain.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Backport driver from upcoming Linux 6.10 and put a pending fix on top
to make sure the netdev trigger offloading behaves as expected.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
With the switch from the uImage.FIT partition parser to fitblk the
cmdline needs to be adjusted as well. Do this now as it has been
forgotten when the switch was done.
Fixes: 6368ed1ae5 ("mediatek: mt7623: phase out uImage.FIT partition parser")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
99dd990690bc treewide: refactor pref(erred) to preferred_lt (lifetime)
4c2b51eab368 treewide: refactor valid to valid_lt (lifetime)
3b4e06055900 router: inherit user-assigned preferred_lifetime
e164414aa184 router: limit prefix preferred_lt to valid_lt in accordance with RFC4861
a2176af7bdeb treewide: spell-fixes and new comments for extra clarification
4590efd3a2b3 treewide: normalize spaces to tabs
2edc60cb7c7a router: rename minvalid to lowest_found_lifetime
7ee72ee17bfa router: disambiguate and clarify 'no route' messages
a29882318a4c config: set RFC defaults for preferred lifetime
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The needed file '.packageinfo' for creating the CycloneDX SBOM in the
imagebuilder is available in the top directory of the imagebuilder and
not in the tmp directory.
For this reason, the creation of the CycloneDX SBOM file is not available
for the imagebuilder.
To fix this, it is now first checked whether the CycloneDX SBOM should be
built at all and then second decided by checking the IB variable where the
'.packageinfo' file is to be found.
With this change, it is now possible to create the CycloneDX SBOM also for
the imagebuilder as well.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
This is an artifact and is not needed. We have already set the
information 'Maintainer:' in the '.packageinfo-*' files.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Support for Renesas Arm families was added in commit 1ff4f4df23
("armsr: armv8: enable CONFIG_ARCH_RENESAS"), but this did not
enable the console/tty hardware for these SoCs, which is derived
from the SuperH family (CONFIG_SERIAL_SH_SCI).
Link: https://github.com/openwrt/openwrt/issues/15284
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Due to a change in kernel 6.2, the GPIO numbers on certain
architectures (including arm64) have changed. This script
will update any defined GPIO switches to the new numbering.
See https://lists.openwrt.org/pipermail/openwrt-devel/2024-March/042448.html
for more information.
In the future, the GPIO switch mechanism will likely be
replaced with something using libgpiod.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
