According to the vendor [1] these HATs share the same DT overlay:
hifiberry-dacplus. The PCM512x-compatible control unit is attached to
I2C, so the additional snd-soc-pcm512x-i2c kernel module is required.
Also explicitly note the Amp2 support to reduce confusion for those
users.
[1] <https://www.hifiberry.com/docs/software/configuring-linux-3-18-x/>
Signed-off-by: Torsten Duwe <duwe@lst.de>
(added bcm27xx tag, changed commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
(cherry picked from commit 7ea9936f7f)
The MikroTik RouterBOARD mAPL-2nd (sold as mAP Lite) is a small
2.4 GHz 802.11b/g/n PoE-capable AP.
See https://mikrotik.com/product/RBmAPL-2nD for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9533
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless: Atheros AR9531 (SoC) 802.11b/g/n 2x2:2, 1.5 dBi antenna
- Ethernet: Atheros AR8229 (SoC), 1x 10/100 port, 802.3af/at PoE in
- 4 user-controllable LEDs:
· 1x power (green)
· 1x user (green)
· 1x lan (green)
· 1x wlan (green)
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Note: following 781d4bfb39
The network setup avoids using the integrated switch and connects the
single Ethernet port directly. This way, link speed (10/100 Mbps) is
properly reported by eth0.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit eb38af7881)
Specification:
- QCA9533 (650 MHz), 64 or 128MB RAM, 16MB SPI NOR
- 2x 10/100 Mbps Ethernet, with 802.3at PoE support (WAN)
- 2T2R 802.11b/g/n 2.4GHz
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Clemens Hopfer <openwrt@wireloss.net>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry-picked from commit a05dcb0724)
[switch to mtd-mac-address instead of nvmem-cells]
Specification:
- QCA9563 (775MHz), 128MB RAM, 16MB SPI NOR
- 2T2R 802.11b/g/n 2.4GHz
- 2T2R 802.11n/ac 5GHz
- 2x 10/100/1000 Mbps Ethernet, with 802.3at PoE support (WAN port)
LED for 5 GHz WLAN is currently not supported as it is connected directly
to the QCA9882 radio chip.
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry-picked from commit c91df224f5)
Fixes two high-severity vulnerabilities:
- CVE-2022-25640: A TLS v1.3 server who requires mutual authentication
can be bypassed. If a malicious client does not send the
certificate_verify message a client can connect without presenting a
certificate even if the server requires one.
- CVE-2022-25638: A TLS v1.3 client attempting to authenticate a TLS
v1.3 server can have its certificate heck bypassed. If the sig_algo in
the certificate_verify message is different than the certificate
message checking may be bypassed.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
(cherry picked from commit e89f3e85eb)
This updates mac80211 to version 5.10.110-1 which is based on kernel
5.10.110.
The removed patches were applied upstream.
This new release contains many fixes which were merged into the upstream
Linux kernel.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rename feature variable clang-bpf-global-var following upstream changes.
This restores the HAVE_CLANG feature override and should avoid rare build
errors where a recent host clang and BTF-enabled host kernel are present.
Fixes: 23be333401 ("bpftools: update to 5.10.10")
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
(cherry picked from commit cf20f1bb5f)
The following devices have a Winbond W25Q256FV flash chip,
which does not have the RESET pin enabled by default,
and otherwise would require setting a bit in a status register.
Before moving to Linux 5.4, we had the patch:
0053-mtd-spi-nor-add-w25q256-3b-mode-switch.patch
which kept specific flash chips with explicit 3-byte and 4-byte address modes
to stay in 3-byte address mode while idle (after an erase or write)
by using a custom flag SPI_NOR_4B_READ_OP that was part of the patch.
this was obsoleted by the patch:
481-mtd-spi-nor-rework-broken-flash-reset-support.patch
which uses the newer upstream flag SNOR_F_BROKEN_RESET
for devices with a flash chip that cannot be hardware reset with RESET pin
and therefore must be left in 3-byte address mode when idle.
The new patch requires that the DTS of affected devices
have the property "broken-flash-reset", which was not yet added for most of them.
This commit adds the property for remaining affected devices in ramips target,
specifically because of the flash chip model.
However, it is possible that there are other devices
where the flash chip uses an explicit 4-byte address mode
and the RESET pin is not connected to the SOC on the board,
and those DTS would also need this property.
Ref: 22d982ea00 ("ramips: add support for switching between 3-byte and 4-byte addressing")
Ref: dfa521f129 ("generic: spi-nor: rework broken-flash-reset")
Signed-off-by: Michael Pratt <mcpratt@pm.me>
[pepe2k@gmail.com: backported to 21.02]
Fixes: #9655, #9636, #9547
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
(backported from commit 74516f4357)
When using external targets there is a symlink being created for the
target under target/linux which then becomes dangling under Image
Builder. Fix it by dereferencing the possible symlink.
Tested on IB with external target, ipq40xx and mvebu.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 621f39d1f4)
(cherry picked from commit ec9af870f3)
When upgrading a TP-Link Archer C5 v1 from ar71xx to ath79,
the 5ghz radio stops working because the device path changed.
Same has been done for the Archer C7 before:
commit e19506f206 ("ath79: migrate Archer C7 5GHz radio device paths")
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
(cherry picked from commit c6eb63d48f)
The label has the MAC address of eth0, not the WLAN PHY address. We can
merge the definition back into ar7241_ubnt_unifi.dtsi, as both DTS
derived from it use the same interface for their label MAC addresses
after all.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit aee9ccf5c1)
This backports the following upstream Linux patches
net: sfp: add mode quirk for GPON module Ubiquiti U-Fiber Instant
net: sfp: relax bitrate-derived mode check
net: sfp: cope with SFPs that set both LOS normal and LOS inverted
for 5.4 for mvebu platform.
This fixes GPON modules:
Ubiquiti U-Fiber Instant SFP GPON
VSOL V2801F
CarlitoxxPro CPGOS03-0490 v2.0
Signed-off-by: Marek Behún <marek.behun@nic.cz>
- Binary files were renamed to cyfmac from brcmfmac, but the files needs
to be on the router with the previous naming
[ 6.656165] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac43455-sdio for chip BCM4345/6
[ 6.665182] brcmfmac mmc1:0001:1: Direct firmware load for brcm/brcmfmac43455-sdio.bin failed with error -2
[ 6.674928] brcmfmac mmc1:0001:1: Falling back to sysfs fallback for: brcm/brcmfmac43455-sdio.bin
- Cypress were acquired by Infineon Technologies
Thus change the project URL and switch to download files from their
GitHub repository. This is much better than the previous solution, which
requires finding new threads on their community forum about new driver
updates, and it will be necessary to change the URL each time.
Unfortunately, it seems that there is not published changelog, but
according to this forum thread [1], be careful by opening the link from
solution since it contains ending bracket ), it brings fixes for various
security vulnerabilities, which were fixed in 7_45_234.
Fixes:
- FragAttacks
- Kr00k
Also add LICENSE file
Run tested on Seeedstudio router powered by Raspberry Pi 4 CM with
package cypress-firmware-43455-sdio.
Before:
root@OpenWrt:~# dmesg | grep 'Firmware: BCM4345/6'
[ 6.895050] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Mar 23 2020 02:20:01 version 7.45.206 (r725000 CY) FWID 01-febaba43
After:
root@OpenWrt:~# dmesg | grep 'Firmware: BCM4345/6'
[ 6.829805] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM4345/6 wl0: Apr 15 2021 03:03:20 version 7.45.234 (4ca95bb CY) FWID 01-996384e2
[1] https://community.infineon.com/t5/Wi-Fi-Bluetooth-for-Linux/Outdated-brcmfmac-firmware-for-Raspberry-Pi-4-in-OpenWrt-21-02-1/m-p/331593#M2269
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 7ca7e0b22d)
The OCEDO Raccoon had significant packet-loss with cables longer than 50
meter. Disabling EEE restores normal operation.
Also change the ethernet config to reduce loss on sub-1G links.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 4551bfd91f)
Required to allow sysupgrades from OpenWrt 19.07.
Closes#7071
Fixes: 98fbf2edc0 ("ath79: move TPLINK_HWID/_HWREV to parent for tplink-safeloader")
Tested-by: J. Burfeind <git@aiyionpri.me>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 8ba71f1f6f)
Tavis has just reported, that he was recently trying to track down a
reproducible crash in a compressor. Believe it or not, it really was a
bug in zlib-1.2.11 when compressing (not decompressing!) certain inputs.
Tavis has reported it upstream, but it turns out the issue has been
public since 2018, but the patch never made it into a release. As far as
he knows, nobody ever assigned it a CVE.
Suggested-by: Tavis Ormandy <taviso@gmail.com>
References: https://www.openwall.com/lists/oss-security/2022/03/24/1
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit b3aa2909a7)
(cherry picked from commit 3965dda0fa)
a20-olinuxino-lime2 is currently having hard time with link detection of
certain 1000Mbit partners due to usage of generic PHY driver, probably
due to following missing workaround introduced in upstream in commit
3aed3e2a143c ("net: phy: micrel: add Asym Pause workaround"):
The Micrel KSZ9031 PHY may fail to establish a link when the Asymmetric
Pause capability is set. This issue is described in a Silicon Errata
(DS80000691D or DS80000692D), which advises to always disable the
capability. This patch implements the workaround by defining a KSZ9031
specific get_feature callback to force the Asymmetric Pause capability
bit to be cleared.
This fixes issues where the link would not come up at boot time, or when
the Asym Pause bit was set later on.
As a20-olinuxino-lime2 has Micrel KSZ9031RNXCC-TR Gigabit PHY since
revision H, so we need to use Micrel PHY driver on those devices.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit ffa1088f63)
uDPU has 2 LM75 compatible temperature sensors, so include the driver for
them by default in order to utilize them.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebase]
(cherry picked from commit a8b2d35903)
(cherry picked from commit b9e90935db)
uDPU provides a FIT based initramfs, but currently gets stuck after U-boot
starts the kernel at "Starting kernel..".
It is due to the load address being too low, so increase it in order to get
the initramfs booting again.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 80f21e5336)
(cherry picked from commit d65269a732)
The label has the MAC address of eth0, not the WLAN PHY address.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit 2a02b70499)
This firmware should only be used for mobile devices (e.g. laptops), where
AP mode functionality is typically not used. This firmware supports a lot
of power saving offload functionality at the expense of AP mode support.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit a1ac8728f8)
Add the STAs extended capabilities to the ubus STA information. This
way, external daemons can be made aware of a STAs capabilities.
This field is of an array type and contains 0 or more bytes of a STAs
advertised extended capabilities.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 6f78723977)
Include the current operation class to hostapd get_status interface.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 2a31e9ca97)
Add the beacon interval to hostapd status output. This allows external
services to discover the beacon interval for a specific VAP.
This way, external wireless management daemons can correctly calculate
fields containing TBTT value from absolute time-values.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 3ba9846842)
Imports a function from iw to convert frequencies to channel numbers.
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Martin Weinelt <hexa@darmstadt.ccc.de>
[fix potential out of bounds read]
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 398df62756)
To allow steering daemons to be aware of the STA-decided transition
target, publish WNM transition responses to ubus. This way, steerings
daemons can learn about STA-chosen targets and send a better selection
of transition candidates.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit a3de42e72c)
The existing wnm_disassoc_imminent ubus method only supports issuing a
bss transition request with the disassoc imminent flag set.
For use-cases, where the client is requested to roam to another BSS
without a pending disassoc, this existing method is not suitable.
Add a new bss_transition_request ubus method, which provides a more
universal way to dispatch a transition request. It takes the following
arguments:
Required:
addr: String - MAC-address of the STA to send the request to (colon-seperated)
Optional:
abridged - Bool - Indicates if the abridged flag is set
disassociation_imminent: Bool - Whether or not the disassoc_imminent
flag is set
disassociation_timer: I32 - number of TBTTs after which the client will
be disassociated
validity_period: I32 - number of TBTTs after which the beacon
candidate list (if included) will be invalid
neighbors: blob-array - Array of strings containing neighbor reports as
hex-string
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 0eed96ca5d)
This is a bugfix release. Changelog:
*) Fixed a bug in the BN_mod_sqrt() function that can cause it to loop
forever for non-prime moduli. (CVE-2022-0778)
*) Add ciphersuites based on DHE_PSK (RFC 4279) and ECDHE_PSK
(RFC 5489) to the list of ciphersuites providing Perfect Forward
Secrecy as required by SECLEVEL >= 3.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
(cherry picked from commit e17c6ee627)
This fixes:
bash: xxd: command not found
on hosts without xxd installed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 9dbca6bf6e)
Fixes: 45b3f2aa0f ("uboot-bcm4908: add package with BCM4908 U-Boot")
Don't download all of vim just to build xxd. Use a tight tarball
containing only xxd sources instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 2b94aac7a1)
U-Boot requires xxd to create the default environment from an external
file as done in uboot-mediatek.
Build xxd (only, not the rest of vim) as part of tools to make sure it
is present on the buildhost.
Reported-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit c4dd2441e7)
OpenWrt uses a lot of (b)ash scripts for initial setup. This isn't the
best solution as they almost never consider syncing files / data. Still
this is what we have and we need to try living with it.
Without proper syncing OpenWrt can easily get into an inconsistent state
on power cut. It's because:
1. Actual (flash) inode and data writes are not synchronized
2. Data writeback can take up to 30 seconds (dirty_expire_centisecs)
3. ubifs adds extra 5 seconds (dirty_writeback_centisecs) "delay"
Some possible cases (examples) for new files:
1. Power cut during 5 seconds after write() can result in all data loss
2. Power cut happening between 5 and 35 seconds after write() can result
in empty file (inode flushed after 5 seconds, data flush queued)
Above affects e.g. uci-defaults. After executing some migration script
it may get deleted (whited out) without generated data getting actually
written. Power cut will result in missing data and deleted file.
There are three ways of dealing with that:
1. Rewriting all user-space init to proper C with syncs
2. Trying bash hacks (like creating tmp files & moving them)
3. Adding sync and hoping for no power cut during critical section
This change introduces the last solution that is the simplest. It
reduces time during which things may go wrong from ~35 seconds to
probably less than a second. Of course it applies only to IO operations
performed before /etc/init.d/boot . It's probably the stage when the
most new files get created.
All later changes are usually done using smarter C apps (e.g. busybox or
uci) that creates tmp files and uses rename() that is expected to be
atomic.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
(cherry picked from commit 9851d4b6ce)
This is a step forward in adding support for devices with U-Boot.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 34fd5e325a)
New BCM4908 devices come with U-Boot instead of CFE. Firmwares for such
devices has to include U-Boot.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 0d45e1ea96)
This driver is needed to boot from CompactFlash on the Siemens Futro S400.
The device has an AMD NX1500 CPU, which seems to be unsupported by the
geode subtarget, so it must use legacy.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
(cherry picked from commit c8350dfb3c)
1. Create "rootfs_data" dynamicaly
U-Boot firmware images can contain only 2 UBI volumes: bootfs (container
with U-Boot + kernel + DTBs) and rootfs (e.g. squashfs). There is no way
to include "rootfs_data" UBI volume or make firmware file tell U-Boot to
create one.
For that reason "rootfs_data" needs to be created dynamically. Use
preinit script to handle that. Fire it right before "mount_root" one.
2. Relate "rootfs_data" to flashed firmware
As already explained flashing new firmware with U-Boot will do nothing
to the "rootfs_data". It could result in new firmware reusing old
"rootfs_data" overlay UBI volume and its file. Users expect a clean
state after flashing firmware (even if flashing the same one).
Solve that by reading flash counter of running firmware and storing it
in "rootfs_data" UBI volume. Every mismatch will result in wiping old
data.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 93259e8ca2)
This fixes problem with USB PHY not handling some USB 3.0 devices.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 0dbcefdd52)
For debugging purposes, we need to know if users are using modified
U-boot versions or not. Currently, the U-boot version is somehow
stripped. This is a little bit problematic when there are
backported/wip/to-upstream patches.
To make it more confusing, there was (before this commit) two U-boot
versioning. U-boot compiled by OpenWrt build bots are missing ``Build:``
This is also the case when the U-boot is compiled locally.
Example:
```
U-Boot SPL 2022.01 (Jan 27 2022 - 00:24:34 +0000)
U-Boot 2022.01 (Jan 27 2022 - 00:24:34 +0000)
```
On the other hand, if you run full build, you can at least see, where it
was compiled. Notice added ``Build:``.
Example:
```
U-Boot 2022.01 (Jan 27 2022 - 00:24:34 +0000), Build: jenkins-turris-os-packages-burstlab-omnia-216
```
In both cases, it is not clear to U-boot developers if it is an unmodified
build. This is also caused that there is a missing ``.git`` file from
U-boot folder, and so there is no history. It leads to that it can not
contain suffix ``-dirty`` (uncommitted modifications) or even something
else like number of commits, etc. [1]
When U-boot is compiled as it should be, the version should look like
this: ``U-Boot 2022.04-rc1-01173-g278195ea1f (Feb 11 2022 - 14:46:50 +0100)``
The date is not changed daily when there are new OpenWrt builds.
This commit adds OpenWrt specific version, which could be verified by
using strings.
```
$ strings bin/targets/mvebu/cortexa9/u-boot-omnia/u-boot-spl.kwb | grep -E "OpenWrt*"
U-Boot SPL 2022.01-OpenWrt-r18942+54-cbfce92367 (Feb 21 2022 - 13:17:34 +0000)
arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.2.0 r18942+54-cbfce92367) 11.2.0
2022.01-OpenWrt-r18942+54-cbfce92367
U-Boot 2022.01-OpenWrt-r18942+54-cbfce92367 (Feb 21 2022 - 13:17:34 +0000)
```
[1] https://u-boot.readthedocs.io/en/latest/develop/version.html
Reported-by: Pali Rohár <pali@kernel.org>
Suggested-by: Karel Kočí <karel.koci@nic.cz>
[rebased for OpenWrt 21.02]
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit d6aa9d9e07)
Release notes:
https://ftp.openbsd.org/pub/OpenBSD/LibreSSL/libressl-3.4.2-relnotes.txt
```
It includes the following security fix
* In some situations the X.509 verifier would discard an error on an
unverified certificate chain, resulting in an authentication bypass.
Thanks to Ilya Shipitsin and Timo Steinlein for reporting.
```
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 495c4f4e19)
The following patch was integrated upstream:
target/linux/bcm4908/patches-5.4/180-i2c-brcmstb-fix-support-for-DSL-and-CM-variants.patch
All other updated automatically.
The new config option CONFIG_BPF_UNPRIV_DEFAULT_OFF is now handled too.
Compile-tested on: lantiq/xrx200, armvirt/64
Runtime-tested on: lantiq/xrx200, armvirt/64
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
From version 2021.09 U-Boot will fixup Turris Omnia's DTB before
booting, separating U-Boot's environment into separate MTD partition
"u-boot-env" [1].
Check if "u-boot-env" MTD partition exists and set the uci defaults
accordingly.
[1] https://lists.denx.de/pipermail/u-boot/2021-July/455017.html
Signed-off-by: Marek Behún <marek.behun@nic.cz>
(cherry picked from commit 713be75439)
Fixes following warning message during image building process:
Finalizing root filesystem...
root-ipq806x/lib/upgrade/asrock.sh: line 1: /lib/functions.sh: No such file or directory
Enabling boot
root-ipq806x/lib/upgrade/asrock.sh: line 1: /lib/functions.sh: No such file or directory
Enabling bootcount
Fixes#9350
Fixes: 98b86296e6 ("ipq806x: add support for ASRock G10")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit fc317a190c)
