Because these capability advertisements default to on in lldpd, they
became absent at reload, and not restart, due to how the reload logic
works ( keep daemon running, send unconfigured and then the new config
via socket ), and it was not evident unless you happened to be looking
for it (e.g. via pcap or tcpdump). It was also not evident from the
manpage ( have now sent patches upstream ).
At reload time, the unconfigure logic disabled them unless they were
explicitly enabled (compare with other settings where 'unconfigure' just
resets them). Now they default to on/enabled at init time, and are
explicitly 'unconfigure'd at startup if the user disables them via:
lldp_mgmt_addr_advertisements=0
lldp_capability_advertisements=0
In other words: explicit is necessary to disable the advertisements.
The same applies to 'configure system capabilities enabled'. Technically
'unconfigure'd is the default but now it is explicit at reload.
Tested on: 23.05.3
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
For interface type parameters, the man page documents patterns:
```
*,!eth*,!!eth1
uses all interfaces, except interfaces starting with "eth",
but including "eth1".
```
* Renamed `_ifname` to `_l2dev`.
* get the l2dev via network_get_physdev (and not l3dev)
* Glob pattern `*` is also valid - use noglob for this
The net result is that now interface 'names' including globs '*' and '!'
inversions are included in the generated lldpd configs.
Temporarily `set -o noglob` and then `set +o noglob` to disable & enable
globbing respectively, because when we pass `*` as an interface choice,
other file and pathnames get sucked in from where the init script runs,
and the `*` never makes it to lldpd.
Tested extensively on: 22.03.6, 23.05.3
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
[ squash with commit bumping release version ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
only available from >= 1.0.15
Comments are useful. Apparently this config parameter was committed when
openwrt used an older version of lldpd which did not yet support it.
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
For certain lldp_class scenarios (2 & 3) a policy must be set also.
Class 4 is default, although it's good to handle the policy eventuality.
Here, set a default lldp_policy for all lldp_class scenarios. Any
lldp_policy can now be set.
Depends on PR #14584 (which introduced an `if` block)
Tested on 22.03.5, 22.03.6
Signed-off-by: Paul Donald <newtwen@gmail.com>
Previously only partially implemented. After commit
5007f488bb lldp_location was never removed
Now, add the value of lldp_location to the generated config.
The location param has a few syntaxes, so the config acquires the first
usage from the man page: 'address country EU'
Supplementary fix for PR #14193 (this param was included in the original
PR #13018 but the lldp_location fixes were absent from PR #14193).
Tested on 22.03.5, 22.03.6
Signed-off-by: Paul Donald <newtwen@gmail.com>
from commit 3ce909914a
The lldpd man page says that "configure lldp tx-interval" can
specify an interval value in milliseconds by appending a "ms" suffix to
the figure. Thus mandating string handling, and not integer comparison.
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
from commit 909f063066
Now pass two params to get_config_cid_ifaces() for:
cid_interface
interface
Each of which is a CSV of interfaces.
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
from commit ac771313eb
portidsubtype takes 1 of 2 possible keywords which do not need quoting:
configure lldp portidsubtype ifname | macaddress
The third keyword 'local' is used in the syntax when individual ports
are being defined:
configure [ports ethX [,…]] lldp portidsubtype local value
When this syntax is used, quoting is useful (see test cases for lldpd).
In the init file, the 'local' syntax is unused.
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
from commit c98ee4dbb3
agent-type takes 1 of 3 possible keywords which do not require quoting:
configure lldp agent-type nearest-bridge | nearest-non-tpmr-bridge
| nearest-customer-bridge
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen@gmail.com>
Bind to the configured system interfaces only. Switchport interfaces
are no longer ignored and uci interface values for LLDPD are honored.
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
Init script reload with trigger to detect config file update.
Reload command added to attempt non-impactful lldpd reload where
lldpcli can be used to update config without process restart.
Config hash function used to track whether process restart is needed.
Signed-off-by: Stephen Howell <howels@allthatwemight.be>
allow to overwrite the detected system capabilities e.g. if devices
does not operate as bridge.
Signed-off-by: Sebastian Pflieger <sebastian@pflieger.email>
add option to set management IP pattern
also add missing 'unconfigure system hostname'
for example pattern '!192.168.1.1' makes it possible that
WAN IP is selected instead of LAN IP
Signed-off-by: Daniel A. Maierhofer <git@damadmai.at>
[grammar and spelling fixes in commit message]
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
commit eb204d14f75c ("base-files: implement generic service_running")
introduced generic service_running so it's not needed to copy&paste same
3 lines over and over again.
I've removed service_running from netifd/network init script as well,
because it was not working properly, looked quite strange and I didn't
understand the intention:
$ /etc/init.d/network stop
$ service network running && echo "yes" || echo "nope"
( have to wait for 30s )
Command failed: Request timed out
yes
Signed-off-by: Petr Štetiar <ynezz@true.cz>
I think I added these respawn params [a while back],
when I did the conversion to procd init script format.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Enabling this makes it possible to query LLDP neighbors via SNMP.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Jo-Philipp Wich <jo@mein.io>
During reload, we could send invalid information to the other
side and confuse it.
That's why, during reload we'll pause execution, do the reconfig
and resume + update when reload is done.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
The problem is that interfaces are specified at start as
command line arguments, making them unchange-able via reload.
That means, we have to move (since lldpd allows this) the
interfaces-match-pattern option to be in a config file and reload
the configuration.
It's either that, or do a 'restart'.
Since we're generating the lldpd.conf file, we'll have to
move the 'sysconfdir' of lldpd to /tmp, where the files will
get written ; this will prevent any unncessary flash writes.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
With the addition of /etc/os-release patching lldpd to use
/etc/openwrt_release and to have the initscript use
/etc/openwrt_release and/or /etc/openwrt_version becomes
unnecessary.
Signed-off-by: Daniel Dickinson <lede@daniel.thecshore.com>
This should ensure that lldpd is among the first processes to stop,
so that it has time to send the shutdown LLDPU to the other side,
before the network goes down.
Signed-off-by: Alexandru Ardelean <ardeleanalex@gmail.com>
SVN-Revision: 47786
