This patch adds support for the Teltonika RUTX10.
This device is an industrial DIN-rail router with 4 ethernet ports,
2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs.
The RUTX series devices are very similiar so common parts of the DTS
are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev
board.
See https://teltonika-networks.com/product/rutx10 for more info.
Hardware:
SoC: Qualcomm IPQ4018
RAM: 256MB DDR3
SPI Flash 1: XTX XT25F128B (16MB, NOR)
SPI Flash 2: XTX XT26G02AWS (256MB, NAND)
Ethernet: Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports
WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n
Wifi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac
USB Hub: Genesys Logic GL852GT
Bluetooth: Qualcomm CSR8510 (A10U)
LED/GPIO controller: STM32F030 with custom firmware
Buttons: Reset button
Leds: Power (green, cannot be controlled)
WiFi 2.4G activity (green)
WiFi 5G activity (green)
MACs Details verified with the stock firmware:
eth0: Partition 0:CONFIG Offset: 0x0
eth1: = eth0 + 1
radio0 (2.4 GHz): = eth0 + 2
radio1 (5.0 GHz): = eth0 + 3
Label MAC address is from eth0.
The LED/GPIO controller needs a separate kernel driver to function.
The driver was extracted from the Teltonika GPL sources and can be
found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt
USB detection of the bluetooth interface is sometimes a bit flaky. When
not detected power cycle the device. When the bluetooth interface was
detected properly it can be used with bluez / bluetoothctl.
Flash instructions via stock web interface (sysupgrade based):
1. Set PC to fixed ip address 192.168.1.100
2. Push reset button and power on the device
3. Open u-boot HTTP recovery at http://192.168.1.1
4. Upload latest stock firmware and wait until the device is rebooted
5. Open stock web interface at http://192.168.1.1
6. Set some password so the web interface is happy
7. Go to firmware upgrade settings
8. Choose
openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi
9. Set 'Keep settings' to off
10. Click update, when warned that it is not a signed image proceed
Return to stock firmware:
1. Set PC to fixed ip address 192.168.1.100
2. Push reset button and power on the device
3. Open u-boot HTTP recovery at http://192.168.1.1
4. Upload latest stock firmware and wait until the device is rebooted
Note: The DTS expects OpenWrt to be running from the second rootfs
partition. u-boot on these devices hot-patches the DTS so running from the
first rootfs partition should also be possible. If you want to be save follow
the instructions above. u-boot HTTP recovery restores the device so that when
flashing OpenWrt from stock firmware it is flashed to the second rootfs
partition and the DTS matches.
Signed-off-by: Felix Matouschek <felix@matouschek.org>
This adds support for the MikroTik RouterBOARD RBD53iG-5HacD2HnD
(hAP ac³), a indoor dual band, dual-radio 802.11ac
wireless AP with external omnidirectional antennae, USB port, five
10/100/1000 Mbps Ethernet ports and PoE passthrough.
See https://mikrotik.com/product/hap_ac3 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4019
- RAM: 256 MB
- Storage: 16 MB NOR + 128 MB NAND
- Wireless:
· Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
· Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi antennae
- Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in, PoE passtrough on port 5
- 1x USB Type A port
Installation:
1. Boot the initramfs image via TFTP
2. Run "cat /proc/mtd" and look for "ubi" partition mtd device number, ex. "mtd1"
3. Use ubiformat to remove MikroTik specific UBI volumes
* Detach the UBI partition by running: "ubidetach -d 0"
* Format the partition by running: "ubiformat /dev/mtdN -y"
Replace mtdN with the correct mtd index from step 2.
3. Flash the sysupgrade image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
Tested-by: Mark Birss <markbirss@gmail.com>
Tested-by: Michael Büchler <michael.buechler@posteo.net>
Tested-by: Alex Tomkins <tomkins@darkzone.net>
The Zyxel NBG6617 already uses lzma to compress the kernel.
A local build with every module enabled (either as =Y or =M)
ended produced a 3058 KiB kernel (the kernel partition is 4MiB).
It booted just fine, let's reenable the device.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
P&W R619AC is a IPQ4019 Dual-Band AC1200 router.
It is made by P&W (p2w-tech.com) known as P&W R619AC
but marketed and sold more popularly as G-DOCK 2.0.
Specification:
* SOC: Qualcomm Atheros IPQ4019 (717 MHz)
* RAM: 512 MiB
* Flash: 16 MiB (NOR) + 128 MiB (NAND)
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN)
* Wireless:
- 2.4 GHz b/g/n Qualcomm Atheros IPQ4019
- 5 GHz a/n/ac Qualcomm Atheros IPQ4019
* USB: 1 x USB 3.0
* LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED)
* Input: 1 x reset
* 1 x MicroSD card slot
* Serial console: 115200bps, pinheader J2 on PCB
* Power: DC 12V 2A
* 1 x Unpopulated mPCIe Slot (see below how to connect it)
* 1 x Unpopulated Sim Card Slot
Installation:
1. Access to tty console via UART serial
2. Enter failsafe mode and mount rootfs
<https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset>
3. Edit inittab to enable shell on tty console
`sed -i 's/#ttyM/ttyM/' /etc/inittab`
4. Reboot and upload `-nand-factory.bin` to the router (using wget)
5. Use `sysupgrade` command to install
Another installation method is to hijack the upgrade server domain
of stock firmware, because it's using insecure http.
This commit is based on @LGA1150(at GitHub)'s work
<a4932c8d5a>
With some changes:
1. Added `qpic_bam` node in dts. I don't know much about this,
but I observed other dtses have this node.
2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not
working. This fix is from
<51143b4c75>
3. Removed the 32MB NOR variant.
4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes
wlan2g led light up.
5. Added ethphy led config in dts.
6. Changed nand partition label from `rootfs` to `ubi`.
About the 128MiB variant: The stock bootloader sets size of nand to 64MiB.
But most of this devices have 128MiB nand. If you want to use all 128MiB,
you need to modify the `MIBIB` data of bootloader. More details can be
found on github:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060>
For instructions on how to flash the MIBIB partition from u-boot console:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232>
About the Mini PCIe slot: (from "ygleg")
"The REFCLK signals on the Mini PCIe slot is not connected on
this board out of the box. If you want to use the Mini PCIe slot
on the board, you need to (preferably) solder two 0402 resistors:
R436 (REFCLK+) and R444 (REFCLK-)..."
This and much more information is provoided in the github comment:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670>
Signed-off-by: Richard Yu <yurichard3839@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
[Added comment about MIBIB+128 MiB variant. Added commit
message section about pcie slot. Renamed gpio-leds' subnodes
and added color, function+enum properties.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
After switch to 5.10 kernel, kernel size was too high.
This patch switches Cell-C RTL30VW from uImage to zImage build.
Lzma uImage wrap is required for factory booting and it must left
untouched.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Disable some of the ipq40xx devices due to their kernel size limitations.
These devices fail to build with kernel 5.10 and full buildbot config.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[keep gl-b1300/gl-s1300 enabled, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Netgear SRS60 and SRR60 (sold together as SRK60) are two almost
identical AC3000 routers. The SRR60 has one port labeled as wan while
the SRS60 not. The RBR50 and RBS50 (sold together as RBK50) have a
different external shape but they have an USB 2.0 port on the back.
This patch has been tested only on SRS60 and RBR50, but should work
on SRR60 and RBS50.
Hardware
--------
SoC: Qualcomm IPQ4019 (717 MHz, 4 cores 4 threads)
RAM: 512MB DDR3
FLASH: 4GB EMMC
ETH:
- 3x 10/100/1000 Mbps Ethernet
- 1x 10/100/1000 Mbps Ethernet (WAN)
WIFI:
- 2.4GHz: 1x IPQ4019 (2x2:2)
- 5GHz: 1x IPQ4019 (2x2:2)
- 5GHz: 1x QCA9984 (4x4:4)
- 6 internal antennas
BTN:
- 1x Reset button
- 1x Sync button
- 1x ON/OFF button
LEDS:
- 8 leds controlled by TLC59208F (they can be switched on/off
independendently but the color can by changed by GPIOs)
- 1x Red led (Power)
- 1x Green led (Power)
UART:
- 115200-8-N-1
Everything works correctly.
Installation
------------
These routers have a dual partition system. However this firmware works
only on boot partition 1 and the OEM web interface will always flash on
the partition currently not booted.
The following steps will use the SRS60 firmware, but you have to chose
the right firmware for your router.
There are 2 ways to install Openwrt the first time:
1) Using NMRPflash
1. Download nmrpflash (https://github.com/jclehner/nmrpflash)
2. Put the openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img
file in the same folder of the nmrpflash executable
3. Connect your pc to the router using the port near the power button.
4. Run "nmrpflash -i XXX -f openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img".
Replace XXX with your network interface (can be identified by
running "nmrpflash -L")
5. Power on the router and wait for the flash to complete. After about
a minute the router should boot directly to Openwrt. If nothing
happens try to reboot the router. If you have problems flashing
try to set "10.164.183.253" as your computer IP address
2) Without NMRPflash
The OEM web interface will always flash on the partition currently not
booted, so to flash OpenWrt for the first time you have to switch to
boot partition 2 and then flash the factory image directly from the OEM
web interface.
To switch on partition 2 you have to enable telnet first:
1. Go to http://192.168.1.250/debug.htm and check "Enable Telnet".
2. Connect through telent ("telnet 192.168.1.250") and login using
admin/password.
To read the current boot_part:
artmtd -r boot_part
To write the new boot_part:
artmtd -w boot_part 02
Then reboot the router and then check again the current booted
partition
Now that you are on boot partition 2 you can flash the factory Openwrt
image directly from the OEM web interface.
Restore OEM Firmware
--------------------
1. Download the stock firmware from official netgear support.
2. Follow the nmrpflash procedure like above, using the official
Netgear firmware (for example SRS60-V2.2.1.210.img)
nmrpflash -i XXX -f SRS60-V2.2.1.210.img
Notes
-----
1) You can check and edit the boot partition in the Uboot shell using
the UART connection.
"boot_partition_show" shows the current boot partition
"boot_partition_set 1" sets the current boot partition to 1
2) Router mac addresses:
LAN XX:XX:XX:XX:XX:69
WAN XX:XX:XX:XX:XX:6a
WIFI 2G XX:XX:XX:XX:XX:69
WIFI 5G XX:XX:XX:XX:XX:6b
WIFI 5G (2nd) XX:XX:XX:XX:XX:6c
LABEL XX:XX:XX:XX:XX:69
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[added 5.10 changes for 901-arm-boot-add-dts-files.patch, moved
sysupgrade mmc.sh to here and renamed it, various dtsi changes]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
In the "ipq40xx: switch to Kernel 5.10" discussion at GitHub,
Adrian noted [0] that these GL.iNet Conexa series devices,
GL-B1300 and GL-S1300 failed their image generation [1] as their gzipped
uImage kernel went above 4096k.
While notifying the vendor about this problem [2], I tested all U-Boot
releases from GL.iNet:
- they really fail to boot kernel above 4096k
- they don't support lzma: "Unimplemented compression type 3"
- but they boot zImage
Using zImage (xz compression) the kernel is 2909k which is
more than a megabyte away from the KERNEL_SIZE := 4096k limit.
The gzip compressed version would be 4116k.
[0]: https://github.com/openwrt/openwrt/pull/4620#issuecomment-932765776
[1]: commit 7b1fa276f5 ("ipq40xx: add testing support for kernel 5.10")
[2]: https://forum.gl-inet.com/t/ipq40xx-kernel-size-and-u-boot-v5-10-is-too-big-for-4-mb/17619
Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
The board data file for the Plasma Cloud PA2200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.
Fixes: 4871fd2616 ("ipq40xx: add support for Plasma Cloud PA2200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The board data file for the Plasma Cloud PA1200 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device
package name resulted in a not correctly selected package for the device
specific board-2.bin. The wifi driver has therefore loaded the wrong
calibration information into the wifi chip.
Fixes: ea5bb6bbfe ("ipq40xx: add support for Plasma Cloud PA1200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The board data file for the EnGenius EMR3500 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.
Fixes: 3f61e5e1b9 ("ipq40xx: add support for EnGenius EMR3500")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The board data file for the EnGenius EMD1 is not part of the default
board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong
calibration information will be loaded into the wifi chip.
Fixes: 51f3035978 ("ipq40xx: add support for EnGenius EMD1")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The bootloader will look for a configuration section named ap.dk01.1-c2
in the FIT image. If this doesn't exist, the device won't boot.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
sysupgrade metadata is not flashed to the device, so check-size
should be called _before_ adding metadata to the image.
While at it, do some obvious wrapping improvements.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
When support for Luma WRTQ-329ACN was added, the instructions for
flashing this device include using tools from uboot-envtools package.
Unfortunately the OpenWrt buildroot system omits packages from
DEVICE_PACKAGES when CONFIG_TARGET_MULTI_PROFILE,
CONFIG_TARGET_PER_DEVICE_ROOTFS, CONFIG_TARGET_ALL_PROFILES are set. In
result the official images are without tools mentioned in the
instruction. The workoround for the fashing would be installing
uboot-envtools when booted with initramfs image, but not always the
access to internet is available. The other method would be to issue the
necesary command in U-Boot environment but some serial terminals default
configuration don't work well with pasting lines longer than 80 chars.
Therefore add uboot-envtools to default packages, which adds really
small flash footprint to rootfs, where increased size usually is not an
issue.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
This adds support for the Netgear WAC510 Insight Managed Smart Cloud
Wireless Access Point, an indoor dual-band, dual-radio 802.11ac
business-class wireless AP with integrated omnidirectional antennae
and two 10/100/1000 Mbps Ethernet ports.
For more information see:
<https://www.netgear.com/business/wifi/access-points/wac510>
Specifications:
SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
Flash1: 2 MiB Winbond W25Q16JV SPI-NOR
Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND
Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port,
WAN port active IEEE 802.3af/at PoE in
Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae
Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1
LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN
Serial: Header J2
1 - 3.3 Volt (Do NOT connect!)
2 - TX
3 - RX
4 - Ground
WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter!
The Serial settings are 115200-8-N-1.
Installation via Stock Web Interface:
BTW: The default factory console/web interface login user/password are
admin/password.
In the web interface navigating to Management - Maintenance - Upgrade -
'Firmware Upgrade' will show you what is currently installed e.g.:
Manage Firmware
Current Firmware Version: V5.0.10.2
Backup Firmware Version: V1.2.5.11
Under 'Upgrade Options' choose Local (alternatively SFTP would be
available) then click/select 'Browse File' on the right side, choose
openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar
and hit the Upgrade button below. After a minute or two your browser
should indicate completion printing 'Firmware update complete.' and
'Rebooting AP...'.
Note that OpenWrt will use the WAN PoE port as actual WAN port
defaulting to DHCP client but NOT allowing LuCI access, use LAN port
defaulting to 192.168.1.1/24 to access LuCI.
Installation via TFTP Requiring Serial U-Boot Access:
Connect to the device's serial port and hit any key to stop autoboot.
Upload and boot the initramfs based OpenWrt image as follows:
(IPQ40xx) # setenv serverip 192.168.1.1
(IPQ40xx) # setenv ipaddr 192.168.1.2
(IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb
(IPQ40xx) # bootm
Note: This only runs OpenWrt from RAM and has not installed anything
to flash as of yet. One may permanently install OpenWrt as follows:
Check the MTD device number of the active partition:
root@OpenWrt:/# dmesg | grep 'set to be root filesystem'
[ 1.010084] mtd: device 9 (rootfs) set to be root filesystem
Upload the factory image ending with .ubi to /tmp (e.g. using scp or
tftp). Then flash the image as follows (substituting the 9 in mtd9
below with whatever number reported above):
root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi
And reboot.
Dual Image Configuration:
The default U-Boot boot command bootipq uses the U-Boot environment
variables primary/secondary to decide which image to boot. E.g.
primary=0, secondary=3800000 uses rootfs while primary=3800000,
secondary=0 uses rootfs_1.
Switching their values changes the active partition. E.g. from within
U-Boot:
(IPQ40xx) # setenv primary 0
(IPQ40xx) # setenv secondary 3800000
(IPQ40xx) # saveenv
Or from a OpenWrt userspace serial/SSH console:
fw_setenv primary 0
fw_setenv secondary 3800000
Note that if you install two copies of OpenWrt then each will have its
independent configuration not like when switching partitions on the
stock firmware.
BTW: The kernel log shows which boot partition is active:
[ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB)
vs.
[ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB)
Note: After 3 failed boot attempts it automatically switches partition.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
[squashed netgear-tar commit into main and rename netgear-tar for
now, until it is made generic.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD),
an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet
port.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 256 MB
- Storage: 16 MB NOR
- Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae
- Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in
- 1x Ethernet LED (green)
- 7x user-controllable LEDs
· 1x power (blue)
· 1x user (green)
· 5x rssi (green)
Note:
Serial UART is probably available on the board, but it has not been
tested.
Flashing:
Boot via TFTP the initramfs image. Then, upload a sysupgrade image
via SSH and flash it normally. More info at the "Common procedures
for MikroTik products" page https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC
(hAP ac²), a indoor dual band, dual-radio 802.11ac
wireless AP with integrated omnidirectional antennae, USB port and five
10/100/1000 Mbps Ethernet ports.
See https://mikrotik.com/product/hap_ac2 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4018
- RAM: 128 MB
- Storage: 16 MB NOR
- Wireless:
· Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
· Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
- Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in
- 1x USB Type A port
Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
The bootloader of many ipq40xx boards seems to require the config node
of the FIT image to be 'config@1' (or a secific different value).
This requirement used to be implicitely satisfied because OpenWrt used
to also call the configuration node inside a FIT image 'config@1'.
However, as recent U-Boot now prohibits the use of the '@' symbol as
part of node names, this was changed by
commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes")
Explicitely restore the default name of the configuration node to
'config@1' on ipq40xx.
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The variables KERNEL_INITRAMFS_PREFIX and KERNEL_PREFIX are already
defined in include/image.mk and don't have to be redefined in the
target Makefiles.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[also cover imx6]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:
device/image name: vendor_model
compatible: vendor,model
The equal redundant definitions are a symptom of this process.
Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.
This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since generic images have been split to their own
Makefile boards are showing up twice in menuconfig
as $(eval $(call BuildImage)) was not dropped from
the new generic.mk.
Hence $(eval $(call BuildImage)) was being called
twice.
So, lets simply drop it from generic.mk.
Fixes: 378c7ff282 ("ipq40xx: split generic images into own file")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
MikroTik devices require the use of raw vmlinux out of the self
extracting compressed kernels.
They also require 4K sectors, kernel2minor, partition parser as well as
RouterBoard platform drivers.
So in order to not add unnecessary code to the generic sub target lets
introduce a MikroTik sub target.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Both devices use u-boot env variables to boot OpenWrt from its flash
partition. Using u-boot envtools, it is possible to change the bootcmd
back to the stock firmware partition directly from OpenWrt without
attaching a serial cable or even physically accessing the device.
Signed-off-by: Jan Alexander <jan@nalx.net>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
FLASH1: 4 MiB NOR
FLASH2: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: Reset
LED: Power, Internet
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
OTHER: On board with BLE module - by cp210x USB serial chip
On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed
Install via uboot tftp or uboot web failsafe.
By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi
(IPQ40xx) # run lf
By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8075 (2 ports)
PLC: MaxLinear G.hn 88LX5152
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET, WiFi, PLC Button
LEDS: red/white home, white WiFi
To modify a retail device to run OpenWRT firmware:
1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT
initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'.
2) Power on the device while pressing the recessed reset button next to
the Ethernet ports. This causes the bootloader to retrieve and start
the initramfs.
3) Once the initramfs is booted, the device will come up with IP
192.168.1.1. You can then connect through SSH (allow some time for
the first connection).
4) On the device shell, run 'fw_printenv' to show the U-boot environment.
Backup this information since it contains device unique factory data.
5) Change the boot command to support booting OpenWRT:
# fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm'
6) Change directory to /tmp, download the sysupgrade (e.g. through wget)
and install it with sysupgrade. The device will reboot into OpenWRT.
Notice that there is currently no support for booting the G.hn chip.
This requires userland software we lack the rights to share right now.
Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
Device specifications:
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200
* GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE
* GPIO-LEDs for power (orange) and status (blue)
* 1x GPIO-button (reset)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3at POE+
+ used as WAN interface
* 12V 2A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
* QCA IPQ4018
* 256 MB of RAM
* 32 MB of SPI NOR flash (w25q256)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200
* 3x GPIO-LEDs for status (cyan, purple, yellow)
* 1x GPIO-button (reset)
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio4:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ used as LAN interface
- phy@mdio3:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 802.3af/at POE(+)
+ used as WAN interface
* 12V/24V 1A DC
Flashing instructions:
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai>
[sven@narfation.org: prepare commit message, rebase, use all LEDs, switch
to dualboot_datachk upgrade script, use eth1 as designated WAN interface]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Adjust spelling of vendor name to what is used in other places.
Also move definition in shared section.
Signed-off-by: Moritz Warning <moritzwarning@web.de>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The OpenMesh related files were not updated since a while and the new
coding style requirements weren't integrated. This can cause problems
for new devices when an author uses these files as starting point.
* use SPDX-License-Identifiers instead of full license texts
* drop linux,default-trigger with value default-off for LEDs
* led nodes with label "abc:xyz" should have name "xyz_abc"
* led DT labels for "xyz_abc" should be "led_xyz_abc"
* "m25p80@0" flash node should be renamed to "flash@0"
* drop unnecessary empty lines
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[minor commit title and message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds several stylistic and functional improvements of the recently
added Edgecore ECW5211, especially:
* Drop the local BDFs as those are already in the upstream under different names
* Add SPDX tag to DTS
* Add label MAC address
* Move LED trigger to DTS
* Remove unnecessary status="okay"
* Disable unused SS USB phy as the USB port only supports USB 2.0
* Make uboot-env partition writable
* Remove qcom,poll_required_dynamic property as the driver does not use it
* Tidy up the device recipe
Fixes: 4488b260a0 ("ipq40xx: add Edgecore ECW5211 support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Acked-by: Robert Marko <robert.marko@sartura.hr>
The Linksys MR8300 is based on QCA4019 and QCA9888
and provides three, independent radios.
NAND provides two, alternate kernel/firmware images
with fail-over provided by the OEM U-Boot.
Hardware Highlights:
SoC: IPQ4019 at 717 MHz (4 CPUs)
RAM: 512MB RAM
SoC: Qualcomm IPQ4019 at 717 MHz (4 CPUs)
RAM: 512M DDR3
FLASH: 256 MB NAND (Winbond W29N02GV, 8-bit parallel)
ETH: Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks)
BTN: Reset and WPS
USB: USB3.0, single port on rear with LED
SERIAL: Serial pads internal (unpopulated)
LED: Four status lights on top + USB LED
WIFI1: 2x2:2 QCA4019 2.4 GHz radio on ch. 1-14
WIFI2: 2x2:2 QCA4019 5 GHz radio on ch. 36-64
WIFI3: 2x2:2 QCA9888 5 GHz radio on ch. 100-165
Support is based on the already supported EA8300.
Key differences:
EA8300 has 256MB RAM where MR8300 has 512MB RAM.
MR8300 has a revised top panel LED setup.
Installation:
"Factory" images may be installed directly through the OEM GUI using
URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1)
Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com>
[copied Hardware-highlights from EA8300. Fixed alphabetical order.
fixed commit subject, removed bogus unit-address of keys,
fixed author (used Signed-off-By to From:) ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Luma Home WRTQ-329ACN, also known as Luma WiFi System, is a dual-band
wireless access point.
Specification
SoC: Qualcomm Atheros IPQ4018
RAM: 256 MB DDR3
Flash: 2 MB SPI NOR
128 MB SPI NAND
WIFI: 2.4 GHz 2T2R integrated
5 GHz 2T2R integrated
Ethernet: 2x 10/100/1000 Mbps QCA8075
USB: 1x 2.0
Bluetooth: 1x 4.0 CSR8510 A10, connected to USB bus
LEDS: 16x multicolor LEDs ring, controlled by MSP430G2403 MCU
Buttons: 1x GPIO controlled
EEPROM: 16 Kbit, compatible with AT24C16
UART: row of 4 holes marked on PCB as J19, starting count from the side
of J19 marking on PCB
1. GND, 2. RX, 3. TX, 4. 3.3V
baud: 115200, parity: none, flow control: none
The device supports OTA or USB flash drive updates, unfotunately they
are signed. Until the signing key is known, the UART access is mandatory
for installation. The difficult part is disassembling the casing, there
are a lot of latches holding it together.
Teardown
Prepare three thin, but sturdy, prying tools. Place the device with back
of it facing upwards. Start with the wall having a small notch. Insert
first tool, until You'll feel resistance and keep it there. Repeat the
procedure for neighbouring walls. With applying a pressure, one edge of
the back cover should pop up. Now carefully slide one of the tools to
free the rest of the latches.
There's no need to solder pins to the UART holes, You can use hook clips,
but wiring them outside the casing, will ease debuging and recovery if
problems occur.
Installation
1. Prepare TFTP server with OpenWrt initramfs image.
2. Connect to UART port (don't connect the voltage pin).
3. Connect to LAN port.
4. Power on the device, carefully observe the console output and when
asked quickly enter the failsafe mode.
5. Invoke 'mount_root'.
6. After the overlayfs is mounted run:
fw_setenv bootdelay 3
This will allow to access U-Boot shell.
7. Reboot the device and when prompted to stop autoboot, hit any key.
8. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use
'setenv' to do that, then run following commands:
tftpboot 0x84000000 <openwrt_initramfs_image_name>
bootm 0x84000000
and wait till OpenWrt boots.
9. In OpenWrt command line run following commands:
fw_setenv openwrt "setenv mtdids nand1=spi_nand; setenv mtdparts mtdparts=spi_nand:-(ubi); ubi part ubi; ubi read 0x84000000 kernel; bootm 0x84000000"
fw_setenv bootcmd "run openwrt"
10. Transfer OpenWrt sysupgrade image to /tmp directory and flash it
with:
ubirmvol /dev/ubi0 -N ubi_rootfs
sysupgrade -v -n /tmp/<openwrt_sysupgrade_image_name>
11. After flashing, the access point will reboot to OpenWrt, then it's
ready for configuration.
Reverting to OEM firmware
1. Execute installation guide steps: 1, 2, 3, 7, 8.
2. In OpenWrt command line run following commands:
ubirmvol /dev/ubi0 -N rootfs_data
ubirmvol /dev/ubi0 -N rootfs
ubirmvol /dev/ubi0 -N kernel
ubirename /dev/ubi0 kernel1 kernel ubi_rootfs1 ubi_rootfs
ubimkvol /dev/ubi0 -S 34 -N kernel1
ubimkvol /dev/ubi0 -S 320 -N ubi_rootfs1
ubimkvol /dev/ubi0 -S 264 -N rootfs_data
fw_setenv bootcmd bootipq
3. Reboot.
Known issues
The LEDs ring doesn't have any dedicated driver or application to control
it, the only available option atm is to manipulate it with 'i2cset'
command. The default action after applying power to device is spinning
blue light. This light will stay active at all time. To disable it
install 'i2c-tools' with opkg and run:
i2cset -y 2 0x48 3 1 0 0 i
The light will stay off until next cold boot.
Additional information
After completing 5. step from installation guide, one can disable asking
for root password on OEM firmware by running:
sed -e 's/root❌/root::/' -i /etc/passwd
This is useful for investigating the OEM firmware. One can look
at the communication between the stock firmware and the vendor's
cloud servers or as a way of making a backup of both flash chips.
The root password seems to be constant across all sold devices.
This is output of 'led_ctl' from OEM firmware to illustrate
possibilities of LEDs ring:
Usage: led_ctl [status | upgrade | force_upgrade | version]
led_ctl solid COLOR <brightness>
led_ctl single COLOR INDEX <brightness 0 - 15>
led_ctl spinning COLOR <period 1 - 16 (lower = faster)>
led_ctl fill COLOR <period 1 - 16 (lower = faster)>
( default is 5 )
led_ctl flashing COLOR <on dur 1 - 128> <off dur 1 - 128>
(default is 34) ( default is 34 )
led_ctl pulsing COLOR
COLOR: red, green, blue, yellow, purple, cyan, white
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
[squash "ipq-wifi: add BDFs for Luma Home WRTQ-329ACN" into commit,
changed ubi volumes for easier integration, slightly reworded
commit message, changed ubi volume layout to use standard names all
around]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
flashing the unit
* first update to latest edcore FW as per the PDF instructions
* boot the initramfs
- tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm
* inside the initramfs call the following commiands
- ubiattach -p /dev/mtd0
- ubirmvol /dev/ubi0 -n0
- ubirmvol /dev/ubi0 -n1
- ubirmvol /dev/ubi0 -n2
* scp the sysupgrade image to the board and call
- sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin
Signed-off-by: John Crispin <john@phrozen.org>
This patch adds support for the Edgecore ECW5211 indoor AP.
Specification:
- SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7
- RAM: 256MB DDR3
- NOR Flash: 16MB SPI NOR
- NAND Flash: 128MB MX35LFxGE4AB SPI-NAND
- Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0)
- USB: 1 x USB 3.0 SuperSpeed
- WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn)
- CC2540 BLE connected to USB 2.0 port
- Atmel AT97SC3205T I2C TPM
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019.
Specification
-------------
- SoC: Qualcomm IPQ4019
- RAM: 512MiB
- Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC)
- Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch)
- Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch)
- Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch)
- Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN)
- LED: 4x white LED, 4x orange LED, 1x blue LED
- USB: 1x USB 3.0 port
- Input: 2x tactile switch, 2x slide switch (2x SP3T)
- Serial console: 115200bps, pinheader JP5 on PCB
- Power: DC 12V 2A
Flash instruction
-----------------
1. Set up a TFTP server (IP address: 192.168.11.10)
2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage"
and put it into the TFTP server directory.
3. Connect the TFTP server and WTR-M2133HP.
4. Hold down the AOSS button, then power on the router.
5. After booting OpenWrt initramfs image, connect to the router by SSH.
6. Transfer "squashfs-nand-factory.ubi" to the router.
7. Execute the following commands.
# ubidetach -p /dev/mtd15
# ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi
# fw_setenv bootcmd bootipq
8. Perform reboot.
Recover to stock firmware
-------------------------
1. Execute the following command.
# fw_setenv bootcmd bootbf
2. Reboot and wait several minutes.
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
Specifications:
SOC: Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core
RAM: 512 MiB
FLASH1: 16 MiB NOR - SPI0
FLASH2: 8 GiB eMMC
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2
INPUT: Reset, WPS
LED: Power, Mesh, WLAN
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
UART2: On board with BLE module
SPI1: On board socket for Zigbee module
Install via tftp
- NB: need to flash transition image firstly
Firstly install transition image:
(IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script
Secondly install openwrt sysupgrade bin:
(IPQ40xx) # run lf
Revert to factory image:
(IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img
(IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script
The kernel and rootfs of factory firmware are on eMMC, and openwrt
firmware is on NOR flash. The transition image includes U-boot
and partition table, which decides where to load kernel and rootfs.
After you firstly install openwrt image, you can switch between
factory and openwrt firmware by flashing transition image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
The Device/Default definition sets a default IMAGE/sysupgrade.bin,
but does not enable it by setting IMAGES. This is not consistent,
and has led to IMAGES being defined at various other places in the
file.
Thus, this patch consolidates the default value for IMAGES by putting
it in Device/Default. Since it's still overwritten where necessary,
this patch is cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The ZyXEL NBG6617 has a separate kernel partition which is 4MiB large.
Add the kernel size to validate the kernel won't be bigger than this
fixed limit.
Signed-off-by: David Bauer <mail@david-bauer.net>
The NETGEAR EX61500v2 and EX6150v2 U-Boot does not support booting LZMA
compressed images. Currently, they are using GZIP compressed kernels,
which results in ledd flash being available to the root and overlay
filesystems.
Using a zImage results in a smaller kernel and therefore increases
available space for rootfs and overlayfs.
Size reduced: ~1.1 MiB
Signed-off-by: David Bauer <mail@david-bauer.net>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8072 (2 ports)
USB: 1 x 2.0 (Host controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button
LEDS: White, Blue, Red, Orange
Flash instruction:
From EnGenius firmware to OpenWrt firmware:
In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emr3500-squashfs-factory.bin directly.
From OpenWrt firmware to EnGenius firmware:
1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
Put the EnGenius firmware in the TFTP server directory on your computer.
2. Power up EMR3500. Press 4 and then press any key to enter u-boot.
3. Download EnGenius firmware
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emr3500-nor-fw-s.img
4. Flash the firmware
(IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script
5. Reboot
(IPQ40xx) # reset
Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com>
[squashed update patch, updated to 5.4, dropped BOARD_NAME,
migrated to SOC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware
--------
SoC: Qualcomm IPQ4029
RAM: 512M DDR3
FLASH: - 128MB NAND (Macronix MX30LF1G18AC)
- 4MB SPI-NOR (Macronix MX25R3235F)
TPM: Atmel AT97SC3203
BLE: Texas Instruments CC2540T
attached to ttyMSM0
ETH: Atheros AR8035
LED: System (red / green / amber)
BTN: Reset
The USB port on the device is (in contrast to other Aruba boards) real
USB. The AP uses a CP2101 USB TTY converter on the board.
Console baudrate is 9600 8n1.
To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.
Installation
------------
1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
into the TFTP server root directory. Configure the TFTP server to
be reachable at 192.168.1.75/24. Connect the machine running the TFTP
server to the ethernet port of the access point.
2. Connect to the serial console. Interrupt autobooting by pressing
Enter when prompted.
3. Configure the bootargs and bootcmd for OpenWrt.
$ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8"
$ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
ubi read 0x85000000 kernel; bootm 0x85000000"
$ setenv ramboot_openwrt "run bootargs_openwrt;
setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
netget; set fdt_high 0x87000000; bootm"
$ setenv bootcmd "run nandboot_openwrt"
$ saveenv
4. Load OpenWrt into RAM:
$ run ramboot_openwrt
5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
/tmp folder on the device.
6. Flash OpenWrt:
Make sure you use the mtd partition with the label "ubi" here!
$ ubidetach -p /dev/mtd1
$ ubiformat /dev/mtd1
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:
$ setenv bootcmd "boot"
$ saveenv
Signed-off-by: David Bauer <mail@david-bauer.net>
Cell C RTL30VW is a LTE router with tho gigabit ethernets and integrated
QMI mPCIE modem.
This is stripped version of ASKEY RTL0030VW.
Hardware:
Specification:
-CPU: IPQ4019
-RAM: 256MB
-Flash: NAND 128MB + NOR 16MB
-WiFi: Integrated bgn/ac
-LTE: mPCIe card (Modem chipset MDM9230)
-LAN: 2 Gigabit Ports
-USB: 2x USB2.0
-Serial console: RJ-45 115200 8n1
-Unsupported VoIP
Known issues:
None so far.
Instruction install:
There are two methods: Factory web-gui and serial + tftp.
Web-gui:
1. Apply factory image via stock web-gui.
Serial + initramfs:
1. Rename OpenWrt initramfs image to "image"
2. Connect serial console (115200,8n1)
3. Set IP to different than 192.168.1.11, but 24 bit mask, eg. 192.168.1.4.
4. U-Boot commands:
sf probe && sf read 0x80000000 0x180000 0x10000
setenv serverip 192.168.1.4
set fdt_high 0x85000000
tftpboot 0x84000000 image
bootm 0x84000000
5. Install sysupgrade image via "sysupgrade -n"
Back to stock:
All is needed is swap 0x4c byte in mtd8 from 0 to 1 or 1 to 0,
do firstboot and factory reset with OFW:
1. read mtd8:
dd if=/dev/mtd8 of=/tmp/mtd8
2. go to tmp:
cd /tmp/
3. write first part of partition:
dd if=mtd8 of=mtd8.new bs=1 count=76
4. check which layout uses bootloader:
cat /proc/mtd
5a. If first are kernel_1 and rootfs_1 write 0:
echo -n -e '\x00' >> mtd8.new
5b. If first are kernel and rootfs write 1:
echo -n -e '\x01' >> mtd8.new
6. fill with rest of data:
dd if=mtd8 bs=1 skip=77 >> mtd8.new
7. CHECK IF mtd8.new HAVE CHANGED ONLY ONE BYTE! e.g with:
hexdump mtd8.new
8. write new mtd8 to flash:
mtd write mtd8.new /dev/mtd8
9. do firstboot
10.reboot
11. Do back to factory defaults in OFW GUI.
Based on work: Cezary Jackiewicz <cezary@eko.one.pl>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
MobiPromo CM520-79F is an AC1300 dual band router based on IPQ4019
Specification:
SoC/Wireless: QCA IPQ4019
RAM: 512MiB
Flash: 128MiB SLC NAND
Ethernet PHY: QCA8075
Ethernet ports: 1x WAN, 2x LAN
LEDs: 7 LEDs
2 (USB, CAN) are GPIO
other 5 (2.4G, 5G, LAN1, LAN2, WAN) are connected to a shift register
Button: Reset
Flash instruction:
Disassemble the router, connect UART pins like this:
GND TX RX
[x x . . x .]
[. . . . . .]
(QCA8075 and IPQ4019 below)
Baud-rate: 115200
Set up TFTP server: IP 192.168.1.188/24
Power on the router and interrupt the booting with UART console
env backup (in case you want to go back to stock and need it there):
printenv
(Copy the output to somewhere save)
Set bootenv:
setenv set_ubi 'set mtdids nand0=nand0; set mtdparts mtdparts=nand0:0x7480000@0xb80000(fs); ubi part fs'
setenv bootkernel 'ubi read 0x84000000 kernel; bootm 0x84000000#config@1'
setenv cm520_boot 'run set_ubi; run bootkernel'
setenv bootcmd 'run cm520_boot'
setenv bootargs
saveenv
Boot initramfs from TFTP:
tftpboot openwrt-ipq40xx-generic-mobipromo_cm520-79f-initramfs-fit-zImage.itb
bootm
After initramfs image is booted, backup rootfs partition in case of reverting to stock image
cat /dev/mtd12 > /tmp/mtd12.bin
Then fetch it via SCP
Upload nand-factory.ubi to /tmp via SCP, then run
mtd erase rootfs
mtd write /tmp/*nand-factory.ubi rootfs
reboot
To revert to stock image, restore default bootenv in uboot UART console
setenv bootcmd 'bootipq'
printenv
use the saved dump you did back when you installed OpenWrt to verify that
there are no other differences from back in the day.
saveenv
upload the backed up mtd12.bin and run
tftpboot mtd12.bin
nand erase 0xb80000 0x7480000
nand write 0x84000000 0xb80000 0x7480000
The BOOTCONFIG may have been configured to boot from alternate partition (rootfs_1) instead
In case of this, set it back to rootfs:
cd /tmp
cat /dev/mtd7 > mtd7.bin
echo -ne '\x0b' | dd of=mtd7.bin conv=notrunc bs=1 count=1 seek=4
for i in 28 48 68 108; do
dd if=/dev/zero of=mtd7.bin conv=notrunc bs=1 count=1 seek=$i
done
mtd write mtd7.bin BOOTCONFIG
mtd write mtd7.bin BOOTCONFIG1
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
[renamed volume to ubi to support autoboot,
as per David Lam's test in PR#2432]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Place DEVICE_VARS assignments at the top of the file or above Device/Default
to make them easier to find.
For ramips, remove redundant values already present in parent file.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Generate a cpximg that is compatible with the cpximg loader in Compex' u-boot.
The cpximg loader can be started either by holding the reset button during power
up or by entering the u-boot prompt and entering 'cpximg'.
Once it's running, a TFTP-server under 192.168.1.1 will accept an image
appropriate for the board revision that is etched on the board (e.g. 6A04).
The image can be pushed using tftp:
tftp -v -m binary 192.168.1.1 -c put openwrt-ipq40xx-generic-compex_wpj428-squashfs-cpximg-6a04.bin
cpximg files can also be used with the sysupgrade utility in stock images.
(add SSH key in luci for root access)
In mkmylofw_32m, the calculation of the "partition size" has been preferred
to just padding the partition as this will result in less block transfers
during flashing (while the additional complexity is bearable).
Signed-off-by: Leon M. George <leon@georgemail.eu>
Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the 8devices Habanero development board.
Specs are:
CPU: QCA IPQ4019
RAM: DDR3L 512MB
Storage: 32MB SPI-NOR and optional Parallel SLC NAND(Some boards ship with it and some without)
WLAN1: 2.4 GHz built into IPQ4019 (802.11n) 2x2
WLAN2: 5 GHz built into IPO4019 (802.11ac Wawe-2) 2x2
Ethernet: 5x Gbit LAN (QCA 8075)
USB: 1x USB 2.0 and 1x USB 3.0 (Both built into IPQ4019)
MicroSD slot (Uses SD controller built into IPQ4019)
SDIO3.0/EMMC slot (Uses the same SD controller)
Mini PCI-E Gen 2.0 slot (Built into IPQ4019)
5x LEDs (4 GPIO controllable)
2x Pushbutton (1 is connected to GPIO, other to SoC reset)
LCD ZIF socket (Uses the LCD controller built into IPQ4019 which has no driver support)
1x UART 115200 rate on J18
2x breakout development headers
12V DC Jack for power
DIP switch for bootstrap configuration
Installation instructions:
Since boards ship with vendors fork of OpenWrt sysupgrade can be used.
Signed-off-by: Robert Marko <robimarko@gmail.com>
SOC: IPQ4019 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
FLASH: NOR 4 MiB + NAND 128 MiB
ETH: Qualcomm Atheros QCA8072
WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11a/n/ac 2:2x2
WLAN2: Qualcomm Atheros QCA9888 5GHz 802.11a/n/ac 2:2x2
INPUT: WPS Button
LEDS: Power, LAN1, LAN2, WLAN 2.4GHz, WLAN 5GHz-1, WLAN 5GHz-2, OPMODE
1. Load Ramdisk via U-Boot
To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
* 115200bps
* 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports.
c. Set a static ip 192.168.99.8 for Ethernet that connects to board.
d. The PC must have a TFTP server launched and listening on the interface to which the board is connected.
e. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.
U-BOOT> set serverip 192.168.99.9 && tftpboot 0x84000000 192.168.99.8:openwrt.itb && bootm
Signed-off-by: Steven Lin <steven.lin@senao.com>
[copied 4.19 dts to 5.4]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8072 (1 port)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button
LEDS: White, Blue, Red, Orange
Flash instruction:
From EnGenius firmware to OpenWrt firmware:
In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emd1-squashfs-factory.bin directly.
From OpenWrt firmware to EnGenius firmware:
1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8
Put the EnGenius firmware in the TFTP server directory on your computer.
2. Power up EMD1. Press 4 and then press any key to enter u-boot.
3. Download EnGenius firmware
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emd1-nor-fw-s.img
4. Flash the firmware
(IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script
5. Reboot
(IPQ40xx) # reset
Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com>
[removed BOARD_NAME]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Specifications
==============
- SOC: IPQ4018
- RAM: DDR3 256MB
- Flash: SPI NOR 16MB
- WiFi:
- 2.4GHz: IPQ4018, 2x2, front end SKY85303-11
- 5GHz: IPQ4018, 2x2, front end SKY85717-21
- Ethernet: 1x 10/100/1000Mbps, POE 802.3af
- PHY: QCA8072
- UART: GND, blocked, 3.3V, RX, TX / 115200 8N1
- LED: 1x red / green
- Button: 1x reset / factory default
- U-Boot bootloader with tftp and "emergency web server" accessible
using serial port.
Installation
============
Flash factory image from D-Link web UI. Constraints in the D-Link web UI
makes the factory image unnecessarily large. Flash again using
sysupgrade from inside OpenWrt to reclaim some flash space.
Return to stock D-Link firmware
===============================
Partition layout is preserved, and it is possible to return to the stock
firmware simply by downloading it from D-Link and writing it to the
firmware partition.
# mtd -r write dap2610-firmware.bin firmware
Quirks
======
To be flashable from the D-Link http server, the firmware must be larger
then 6MB, and the size in the firmware header must match the actual file
size. Also, the boot loader verifies the checksum of the firmware before
each boot, thus the jffs2 must be after the checksum covered part. This
is solved in the factory image by having the rootfs at the very end of
the image (without pad-rootfs).
The sysupgrade image which does not have to be flashable from the D-Link
web UI may be smaller, and the checksum in the firmware header only
covers the kernel part of the image.
Signed-off-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com>
[added WRGG Variables to DEVICE_VARS, squashed spi pinconf/mux,
added emd1's gmac0 config,fix dtc warnings]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The Aruba AP-303H is the hospitality version of the Aruba AP-303 with a
POE-passthrough enabled ethernet switch instead of a sigle PHY.
Hardware
--------
SoC: Qualcomm IPQ4029
RAM: 512M DDR3
FLASH: - 128MB SPI-NAND (Macronix)
- 4MB SPI-NOR (Macronix MX25R3235F)
TPM: Atmel AT97SC3203
BLE: Texas Instruments CC2540T
attached to ttyMSM1
ETH: Qualcomm QCA8075
LED: WiFi (amber / green)
System (red / green /amber)
PSE (green)
BTN: Reset
USB: USB 2.0
To connect to the serial console, you can solder to the labled pads next
to the USB port or use your Aruba supplied UARt adapter.
Do NOT plug a standard USB cable into the Console labled USB-port!
Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself
an adapter cable:
VCC - NC
D+ - TX
D- - RX
GND - GND
The console setting in bootloader and OS is 9600 8N1. Voltage level is
3.3V.
To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.
Installation
------------
1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
into the TFTP server root directory. Configure the TFTP server to
be reachable at 192.168.1.75/24. Connect the machine running the TFTP
server to the E0 (!) ethernet port of the access point, as it only
tries to pull from the WAN port.
2. Connect to the serial console. Interrupt autobooting by pressing
Enter when prompted.
3. Configure the bootargs and bootcmd for OpenWrt.
$ setenv bootargs_openwrt "setenv bootargs console=ttyMSM0,9600n8"
$ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
ubi read 0x85000000 kernel; set fdt_high 0x87000000;
bootm 0x85000000"
$ setenv ramboot_openwrt "run bootargs_openwrt;
setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
netget; set fdt_high 0x87000000; bootm"
$ setenv bootcmd "run nandboot_openwrt"
$ saveenv
4. Load OpenWrt into RAM:
$ run ramboot_openwrt
5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
/tmp folder on the device. You will need to plug into E1-E3 ports of
the access point to reach OpenWrt, as E0 is the WAN port of the
device.
6. Flash OpenWrt:
$ ubidetach -p /dev/mtd16
$ ubiformat /dev/mtd16
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:
$ setenv bootcmd "boot"
$ saveenv
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware:
SOC: Qualcomm IPQ4018
RAM: 128 MB Nanya NT5CC64M16GP-DI
FLASH: 16 MB Macronix MX25L12805D
ETH: Qualcomm QCA8075 (4 Gigabit ports, 3xLAN, 1xWAN)
WLAN: Qualcomm IPQ4018 (2.4 & 5 Ghz)
BUTTON: Shared WPS/Reset button
LED: RGB Status/Power LED
SERIAL: Header J8 (UART, Left side of board). Numbered from
top to bottom:
(1) GND, (2) TX, (3) RX, (4) VCC (White triangle
next to it).
3.3v, 115200, 8N1
Tested/Working:
* Ethernet
* WiFi (2.4 and 5GHz)
* Status LED
* Reset Button (See note below)
Implementation notes:
* The shared WPS/Reset button is implemented as a Reset button
* I could not find a original firmware image to reverse engineer, meaning
currently it's not possible to flash OpenWrt through the Web GUI.
Installation (Through Serial console & TFTP):
1. Set your PC to fixed IP 192.168.1.12, Netmask 255.255.255.0, and connect to
one of the LAN ports
2. Rename the initramfs image to 'C0A8010B.img' and enable a TFTP server on
your pc, to serve the image
2. Connect to the router through serial (See connection properties above)
3. Hit a key during startup, to pause startup
4. type `setenv serverip 192.168.1.12`, to set the tftp server address
5. type `tftpboot`, to load the image from the laptop through tftp
6. type `bootm` to run the loaded image from memory
6. (If you want to return to stock firmware later, create an full MTD backup,
e.g. using instructions here https://openwrt.org/docs/guide-user/installation/generic.backup#create_full_mtd_backup)
7. Transfer the 'sysupgrade' OpenWrt firmware image from PC to router, e.g.:
`scp xxx-squashfs-sysupgrade.bin root@192.168.1.1:/tmp/upgrade.bin`
8. Run sysupgrade to permanently install OpenWrt to flash: `sysupgrade -n /tmp/upgrade.bin`
Revert to stock:
To revert to stock, you need the MTD backup from step 6 above:
1. Unpack the MTD backup archive
2. Transfer the 'firmware' partition image to the router (e.g. mtd8_firmware.backup)
3. On the router, do `mtd write mtd8_firmware.backup firmware`
Signed-off-by: Tom Brouwer <tombrouwer@outlook.com>
[removed BOARD_NAME, OpenWRT->OpenWrt, changed LED device name to board name]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch uses the SOC variable to calculate DTS names automatically
based on the SOC and the device definition node name.
This reduces redundancy and (by having to choose DTS name
appropriately) will unify the naming of a device in different places
(image/Makefile, DTS name, compatible, image name). This is supposed
to make life easier for developers and reviewers.
Since the kernel uses a "soc-device.dts" scheme for this target, we
use this for the derivation of DEVICE_DTS, too, and rename the files
not having followed it so far.
Note that for some devices the kernel itself is inconsistent, leaving
us with a manual overwrite for ap.dk01.1-c1 and ap.dk04.1-c1.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware
--------
SoC: Qualcomm IPQ4029
RAM: 512M DDR3
FLASH: - 128MB NAND (Macronix MX30LF1G18AC)
- 4MB SPI-NOR (Macronix MX25R3235F)
TPM: Atmel AT97SC3203
BLE: Texas Instruments CC2540T
attached to ttyMSM0
ETH: Atheros AR8035
LED: WiFi (amber / green)
System (red / green)
BTN: Reset
To connect to the serial console, you can solder to the labled pads next
to the USB port or use your Aruba supplied UARt adapter.
Do NOT plug a standard USB cable into the Console labled USB-port!
Aruba/HPE simply put UART on the micro-USB pins. You can solder yourself
an adapter cable:
VCC - NC
D+ - TX
D- - RX
GND - GND
The console setting in bootloader and OS is 9600 8N1. Voltage level is
3.3V.
To enable a full list of commands in the U-Boot "help" command, execute
the literal "diag" command.
Installation
------------
1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it
into the TFTP server root directory. Configure the TFTP server to
be reachable at 192.168.1.75/24. Connect the machine running the TFTP
server to the ethernet port of the access point.
2. Connect to the serial console. Interrupt autobooting by pressing
Enter when prompted.
3. Configure the bootargs and bootcmd for OpenWrt.
$ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8"
$ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1;
ubi read 0x85000000 kernel; bootm 0x85000000"
$ setenv ramboot_openwrt "run bootargs_openwrt;
setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75;
netget; set fdt_high 0x87000000; bootm"
$ setenv bootcmd "run nandboot_openwrt"
$ saveenv
4. Load OpenWrt into RAM:
$ run ramboot_openwrt
5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the
/tmp folder on the device.
6. Flash OpenWrt:
$ ubidetach -p /dev/mtd1
$ ubiformat /dev/mtd1
$ sysupgrade -n /tmp/openwrt-sysupgrade.bin
To go back to the stock firmware, simply reset the bootcmd in the
bootloader to the original value:
$ setenv bootcmd "boot"
$ saveenv
Signed-off-by: David Bauer <mail@david-bauer.net>
MeshPoint.One is Wi-Fi hotspot and smart IoT gateway (based upon
Jalapeno module from 8Devices).
MeshPoint.One (https://meshpointone.com) is a unique Wi-Fi hotspot and
smart city gateway that can be installed and powered from street
lighting (even solar power in the future). MeshPoint provides up to 27
hours of interrupted Wi-Fi and IoT services from internal battery even
when external power is not available. MeshPoint.One can be used for
disaster relief efforts in order to provide instant Wi-Fi coverage that
can be easily expanded by just adding more devices that create wide area
mesh network. MeshPoint.One devices have standard Luci UI for
management.
Features:
- 1x 1Gpbs WAN
- 1x 1Gbps LAN
- POE input (eth0)
- POE output (eth1)
- Sensor for temperature, humidity and pressure (Bosch BME280)
- current, voltage and power measurement via TI INA230
- Hardware real time clock
- optional power via Li-Ion battery
- micro USB port with USB to serial chip for easy OpenWrt terminal
access
- I2C header for connecting additional sensors
Installation:
-------------
Simply flash the sysupgrade image from stock firmware.
Or use the built in Web recovery into bootloader:
Hold Reset button for 5 to 20 seconds or use UART and httpd command.
Web UI will appear on 192.168.2.100 by default.
For web recovery use the factory.ubi image.
Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
Signed-off-by: Damir Franusic <damir.franusic@sartura.hr>
Signed-off-by: Valent Turkovic <valent@meshpoint.me>
Signed-off-by: Robert Marko <robert@meshpoint.me>
[commit description long line wrap, usb->USB]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This cosmetical patch converts IMAGE_SIZE, KERNEL_SIZE and
BLOCKSIZE definitions to kilobytes, as this is consistent and
easier to read/type.
An exception was made for asus_rt-ac58u, where the IMAGE_SIZE of
20439364 cannot be divided by 1024 (and also does not seem to
match anything in DTS).
Build-tested for all devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This device contains 2 flash devices. One NOR (32M) and one NAND (128M).
U-boot and caldata are on the NOR, the firmware on the NAND.
SoC: IPQ4019
CPU: 4x 710MHz ARMv7
RAM: 256MB
FLASH: NOR:32MB NAND:128MB
ETH: 2x GMAC Gigabit
POE: 802.3 af/at POE, IEEE802.3af/IEEE802.3at(48-56V)
WIFI: 1x 2.4Ghz Atheros qca4019 2x2 MU-MIMO
1x 5.0Ghz Atheros qca4019 2x2 MU-MIMO
USB: 1x 3.0
PCI: 1x Mini PCIe
SIM: 1x Slot
SD: 1x MicroSD slot
BTN: Reset
LED: - Power
- Ethernet
UART: 1x Serial Port 4 Pin Connector (UART)
1x Serial Port 6 Pin Connector (High Speed UART)
POWER: 12V 2A
Installation
------------
Initial flashing can only be done via u-boot using the following commands:
tftpboot openwrt-ipq40xx-generic-compex_wpj419-squashfs-nand-factory.ubi
nand erase.chip; nand write ${fileaddr} 0x0 ${filesize}
res
Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com>
If flash size is used as part of a device's title, it should be
specified as DEVICE_VARIANT like for the other devices so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Hardware
--------
SoC: Qualcomm IPQ4019
RAM: 256M DDR3
FLASH: 128M NAND
WiFi: 2T2R IPQ4019 bgn
2T2R IPQ4019 a/n/ac
ETH: Atheros AR8033 RGMII PHY
BTN: 1x Connect (WPS)
LED: Power (green/red/yellow)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz1200'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz1200.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ1200.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz1200.bin uboot0
> mtd write /path/to/uboot-fritz1200.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
This commit adds support for the 32MB storage/512MB RAM version of the U4019
IPQ4019-based board from Unielec. The board has the following specifications:
* Qualcomm IPQ4019 (running at 717MHz)
* 512MB DDR3 RAM (optional 256MB/1GB)
* 32MB SPI NOR (optional 8/16MB or NAND)
* Five gigabit ports (Qualcomm QCA8075)
* 1x 2.4 GHz wifi (QCA4019 hw1.0)
* 1x 5 Ghz wifi (QCA4019 hw1.0)
* 1x mini-PCIe slot (only USB-pins connected)
* 1x SIM slot (mini-SIM)
* 1x USB2.0 port
* 1x button
* 1x controllable LED
* 1x micro SD-card reader
Working:
* Ethernet
* Wifi
* USB-port
* mini-PCIe slot + SIM slot
* Button
* Sysupgrade
Not working:
* SD card slot (no upstream support)
Installation instructions:
In order to install OpenWRT on the U4019, you need to go via the
initramfs-image. The installation steps are as follows:
* Connect to board via serial (header exposed and clearly marked).
* Interrupt bootloader by pressing a button.
* Copy the initramfs-image to your tftp folder, call the file C0A80079.img.
* Give the network interface connected to the U4019 the address
192.168.0.156/24.
* Start your tftp-server and run tftpboot on the board.
* Run bootm when the file has been transferred, to boot OpenWRT.
* Once OpenWRT has booted, copy the sysupgrade-image to the device and run
sysupgrade to install OpenWRT on the U4019.
Notes:
- Since IPQ4019 has been moved to 4.19, I have not added support for kernel
4.14.
- There is a bug with hardware encryption on IPQ4019, causing poor performance
with TCP and ipsec (see for example FS#2355). In order to improve performance,
I have disabled hardware encryption in the DTS. We can enable hw. enc. once/if
bug is fixed.
- In order for Ethernet to work, the phy has to be reset by setting gpio 47
low/high. Adding support for phy reset via gpio required patching the
mdio-driver, and the code added comes from the vendor driver. I do not know if
patching the driver is an acceptable approach or not.
v1->v2:
* Do not use wildcard as identifier in the board.d-scripts (thanks
Adrian Schmutzler).
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Harri Hursti reported that ALFA Network AP120C-AC does not
work anymore due to: "Unknown package 'ipq-wifi-alfa-network_ap120c-ac'."
This patch fixes the issue by removing the stale package from
the device's dependencies as the calibration data is now
provided by the upstream board-2.bin.
Reported-by: Harri Hursti <harri@nordicinnovationlabs.com>
Fixes: 8f757d427c ("ipq-wifi: drop upstreamed custom board-2.bin")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The BDFs for the:
ALFA Network AP120C-AC
ASUS Lyra
AVM FRITZ!Box 7530
AVM FRITZ!Repeater 3000
EnGenius EAP1300
EnGenius ENS620EXT
Netgear Orbi Pro SRK60
boards were upstreamed to the ath10k-firmware repository
and linux-firmware.git.
Furthermore the BDFs for the:
OpenMesh A42 specific BDFs
OpenMesh A62 specific BDFs
Linksys EA6350v3
have been updated.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three,
independent radios. NAND provides two, alternate kernel/firmware
images with fail-over provided by the OEM U-Boot.
Installation:
"Factory" images may be installed directly through the OEM GUI.
Hardware Highlights:
* IPQ4019 at 717 MHz (4 CPUs)
* 256 MB NAND (Winbond W29N02GV, 8-bit parallel)
* 256 MB RAM
* Three, fully-functional radios; `iw phy` reports (FCC/US, -CT):
* 2.4 GHz radio at 30 dBm
* 5 GHz radio on ch. 36-64 at 23 dBm
* 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm
#{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1
* All two-stream, MCS 0-9
* 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights
* USB3, single port on rear with LED
* WPS and reset buttons
* Four status lights on top
* Serial pads internal (unpopulated)
"Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1"
Implementation Notes:
The OEM flash layout is preserved at this time with 3 MB kernel and
~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and
syscfg (56 MB) partitions are untouched, available as read-only.
Serial Connectivity:
Serial connectivity is *not* required to flash.
Serial may be accessed by opening the device and connecting
a 3.3-V adapter using 115200, 8n1. U-Boot access is good,
including the ability to load images over TFTP and
either run or flash them.
Looking at the top of the board, from the front of the unit,
J3 can be found on the right edge of the board, near the rear
|
J3 |
|-| |
|O| | (3.3V seen, open-circuit)
|O| | TXD
|O| | RXD
|O| |
|O| | GND
|-| |
|
Unimplemented:
* serial1 "ttyQHS0" (serial0 works as console)
* Bluetooth; Qualcomm CSR8811 (potentially conected to serial1)
Other Notes:
https://wikidevi.com/wiki/Linksys_EA8300 states
FCC docs also cover the Linksys EA8250. According to the
RF Test Report BT BR+EDR, "All models are identical except
for the EA8300 supports 256QAM and the EA8250 disable 256QAM."
Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
Extended mksenaofw to support new "capwap" header structure.
This supports flashing from factory 3.0.0, 3.0.1, 3.1.0 and 3.5.5
firmware.
Note that the factory image format changes for 3.1 and later firmware,
and that the 3.1.0 and 3.5.5 Engenius firmware will refuse the
factory_30.bin file. Similarly, the 3.0.0 and 3.0.1 Engenius firmware
will refuse the factory_35.bin file.
Flashing from the Engenius 3.1.0 firmware with the factory_35.bin
firmware has not been tested, as 3.1.0 firmware (Engenius "middleFW")
is only intended as part of the upgrade path to 3.5.5 firmware.
Modified ipq40xx image Makefile to appropriately invoke mksenaofw
with new parameters to configure the capwap header.
Note that there is currently no method to return to factory firmware,
so this is a one-way street.
Path from factory 3.0.0 and 3.0.1 (EnGenius) software to OpenWrt is
to navigate to 192.168.1.1 on the stock firmware and navigate to the
firmware menu. Then copy the URL you have for that page, something like
http://192.168.1.1/cgi-bin/luci/;stok=12345abcdef/admin/system/flashops
and replace the trailing /admin/system/flashops with just /easyflashops
You should then be presented with a simple "Firmware Upgrade" page.
On that page, BE SURE TO CLEAR the "Keep Settings:" checkbox.
Choose the openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_30.bin,
click "Upgrade" and on the following page select "Proceed".
Path from factory 3.5.5 (EnGenius) software to OpenWrt is simply to
use the stock firmware update menu. Choose the
openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_35.bin and click
"Upload" and "Proceed".
The device should then flash the OpenWrt firmware and reboot. Note
that this resets the device to a default configuration with Wi-Fi
disabled, LAN1/PoE acting as a WAN port (running DHCP client) and LAN2
acting as a LAN port with a DHCP server on 192.168.1.x (AP is at
192.168.1.1)
Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[sorry, for unfixing the 80-lines eyesores.]
Hardware
--------
CPU: Qualcomm IPQ4018
RAM: 256M
FLASH: 32M SPI NOR W25Q256
ETH: QCA8075
WiFi2: IPQ4018 2T2R 2SS b/g/n
WiFi5: IPQ4018 2T2R 2SS n/ac
LED: - Power amber
- LAN1(PoE) green
- LAN2 green
- Wi-Fi 2.4GHz green
- Wi-Fi 5GHz green
BTN: - WPS
UART: 115200n8 3.3V J1
VCC(1) - GND(2) - TX(3) - RX(4)
Added basic support to get the device up and running for a sysupgrade
image only.
There is currently no way back to factory firmware, so this is a one-way
street to OpenWRT.
Install from factory condition is convoluted, and may brick your device:
1) Enable SSH and disable the CLI on the factory device from the web user
interface (Management->Advanced)
2) Reboot the device
3) Override the default, limited SSH shell:
a) Get into the ssh shell:
ssh admin@192.168.1.1 /bin/sh --login
b) Change the dropbear script to disable the limited shell. At the
empty command prompt type:
sed -i '/login_ssh/s/^/#/g’ dropbear
/etc/init.d/dropbear restart
exit
4) ssh in to a (now-) normal OpenWRT SSH session
5) Flash your built image
a) scp openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin
admin@192.168.1.1:/tmp/
b) ssh admin@192.168.1.1
c) sysupgrade -n
/tmp/openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin
6) After flash completes (it may say "Upgrade failed" followed by
"Upgrade completed") and device reboots, log in to newly flashed
system. Note you will now need to ssh as root rather than admin.
Signed-off-by: Steve Glennon <s.glennon@cablelabs.com>
[whitespace fixes, reordered partitions, removed rng node from 4.14,
fixed 901-arm-boot-add-dts-files.patch]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M (NANYA NT5CC128M16JR-EK)
FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI)
ETH: Qualcomm QCA8072
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
WiFi5: QCA9984 4T4R 4SS n/ac
LED: - Connect green/blue/red
- Power green
BTN: WPS/Connect
UART: 115200n8 3.3V
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz3000'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ3000.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz3000.bin uboot0
> mtd write /path/to/uboot-fritz3000.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
AVM devices based on Qualcomm IPQ40xx do not store sector health
information in the OOB area. Make this check optional to support this
platform.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
CPU: Qualcomm IPQ4019
RAM: 256M
FLASH: 128M NAND
ETH: QCA8075
VDSL: Intel/Lantiq VRX518 PCIe attached
currently not supported
DECT: Dialog SC14448
currently not supported
WiFi2: IPQ4019 2T2R 2SS b/g/n
WiFi5: IPQ4019 2T2R 2SS n/ac
LED: - Power/DSL green
- WLAN green
- FON/DECT green
- Connect/WPS green
- Info green
- Info red
BTN: - WLAN
- FON
- WPS/Connect
UART: 115200n8 3.3V (located under the Dialog chip)
VCC - RX - TX - GND (Square is VCC)
Installation
------------
1. Grab the uboot for the Device from the 'u-boot-fritz7530'
subdirectory. Place it in the same directory as the 'eva_ramboot.py'
script. It is located in the 'scripts/flashing' subdirectory of the
OpenWRT tree.
2. Assign yourself the IP address 192.168.178.10/24. Connect your
Computer to one of the boxes LAN ports.
3. Connect Power to the Box. As soon as the LAN port of your computer
shows link, load the U-Boot to the box using following command.
> ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin
4. The U-Boot will now start. Now assign yourself the IP address
192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP
server root directory and rename it to 'FRITZ7530.bin'.
5. The Box will now boot OpenWRT from RAM. This can take up to two
minutes.
6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using
scp. SSH into the Box and first write the Bootloader to both previous
kernel partitions.
> mtd write /path/to/uboot-fritz7530.bin uboot0
> mtd write /path/to/uboot-fritz7530.bin uboot1
7. Remove the AVM filesystem partitions to make room for our kernel +
rootfs + overlayfs.
> ubirmvol /dev/ubi0 --name=avm_filesys_0
> ubirmvol /dev/ubi0 --name=avm_filesys_1
8. Flash OpenWRT peristently using sysupgrade.
> sysupgrade -n /path/to/openwrt-sysupgrade.bin
Signed-off-by: David Bauer <mail@david-bauer.net>
[removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Qxwlan E2600AC C1 based on IPQ4019
Specifications:
SOC: Qualcomm IPQ4019
DRAM: 256 MiB
FLASH: 32 MiB Winbond W25Q256
ETH: Qualcomm QCA8075
WLAN: 5G + 5G/2.4G
* 2T2R 2.4/5 GHz
- QCA4019 hw1.0 (SoC)
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
INPUT: Reset buutton
LED: 1x Power ,6 driven by gpio
SERIAL: UART (J5)
UUSB: USB3.0
POWER: 1x DC jack for main power input (9-24 V)
SLOT: Pcie (J25), sim card (J11), SD card (J51)
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "sysupgrade" filename to "firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "sysupgrade" image
and click the upgrade button.
Qxwlan E2600AC C2 based on IPQ4019
Specifications:
SOC: Qualcomm IPQ4019
DRAM: 256 MiB
NOR: 16 MiB Winbond W25Q128
NAND: 128MiB Micron MT29F1G08ABAEAWP
ETH: Qualcomm QCA8075
WLAN: 5G + 5G/2.4G
* 2T2R 2.4/5 GHz
- QCA4019 hw1.0 (SoC)
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
INPUT: Reset buutton
LED: 1x Power, 6 driven by gpio
SERIAL: UART (J5)
USB: USB3.0
POWER: 1x DC jack for main power input (9-24 V)
SLOT: Pcie (J25), sim card (J11), SD card (J51)
Flash instruction (using U-Boot CLI and tftp server):
- Configure PC with static IP 192.168.1.10 and tftp server.
- Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp
server directory.
- Connect PC with one of RJ45 ports, power up the board and press
"enter" key to access U-Boot CLI.
- Use the following command to update the device to OpenWrt: "run lfw".
Flash instruction (using U-Boot web-based recovery):
- Configure PC with static IP 192.168.1.xxx(2-254)/24.
- Connect PC with one of RJ45 ports, press the reset button, power up
the board and keep button pressed for around 6-7 seconds, until LEDs
start flashing.
- Open your browser and enter 192.168.1.1, select "ubi" image
and click the upgrade button.
Signed-off-by: 张鹏 <sd20@qxwlan.com>
[ added rng node. whitespace fixes, ported 02_network,
ipq-wifi Makefile, misc dts fixes, trivial message changes ]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm
IPQ4018 + QCA8075 platform.
Specification:
- Qualcomm IPQ4018 (717 MHz)
- 256 MB of RAM (DDR3)
- 16 MB (SPI NOR) + 128 MB (SPI NAND) of flash
- 2x Gbps Ethernet, with 802.3af PoE support in one port
- 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922)
- 3x U.FL connectors
- 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas
- Atmel/Microchip AT97SC3205T TPM module (I2C bus)
- TI CC2540 Bluetooth LE module (USB 2.0 bus)
- 4x LED (all driven by GPIO)
- 1x button (reset)
- 1x USB 2.0 (optional, not installed in indoor version)
- DC jack for main power input (12 V)
- UART header available on PCB (2.0 mm pitch)
Flash instruction:
1. This board uses dual-image feature (128 MB NAND is divided into two
64 MB partitions: 'rootfs1' and 'rootfs2').
2. Before update, make sure your device is running firmware no older
than v1.1 (previous versions have incompatible U-Boot).
3. Use 'factory' image in vendor GUI or for sysupgrade tool, without
preserving settings.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
SoC: Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores
RAM: 256 MiB (Nanya NT5CC128M16IP-DI)
FLASH: 128 MiB (Macronix NAND)
WiFi0: Qualcomm IPQ4019 b/g/n 2x2
WiFi1: Qualcomm IPQ4019 a/n/ac 2x2
WiFi2: Qualcomm Atheros QCA9886 a/n/ac
BT: Atheros AR3012
IN: WPS Button, Reset Button
OUT: RGB-LED via TI LP5523 9-channel Controller
UART: Front of Device - 115200 N-8
Pinout 3.3v - RX - TX - GND (Square is VCC)
Installation:
1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp.
Login credentials are identical to the Web UI.
2. Login to the device via SSH.
3. Flash the initramfs image using
> mtd-write -d linux -i openwrt-image-file
4. Power-cycle the device and wait for OpenWRT to boot.
5. From there flash the OpenWRT-sysupgrade image.
Ethernet-Ports: Although labeled identically, the port next to
the power socket is the LAN port and the other one is WAN. This
is the same behavior as in the stock firmware.
Signed-off-by: Marius Genheimer <mail@f0wl.cc>
[Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh,
reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79,
minor dts touchup, added rng to 4.19 dts]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Specifications:
SOC: Qualcomm IPQ4018
RAM: 256 MiB Samsung K4B2G1646F-BYK0
FLASH1: MX25L1605D 2 MB
FLASH2: Winbond W25N01GV 128Mb
ETH: Qualcomm QCA8075
WLAN0: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN1: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: WPS, Reset
LED: Status - Green
SERIAL: Header at J19, Beneath DC Power Jack
1-VCC ; 2-TX ; 3-RX; 4-GND;
Serial 115200-8-N-1.
Tested and working:
- USB (requires extra packages)
- LAN Ethernet (Correct MAC-address)
- WAN Ethernet (Correct MAC-address)
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from Web UI
- OpenWRT sysupgrade
- LED
- Reset Button
Need Testing:
- WPS button
Install via Web UI:
- Attach to a LAN port on the router.
- Connect to the Linksys Smart WiFi Page (default 192.168.1.1) and login
- Select the connectivity tab on the left
- In the manual update box on the right
- Select browse, and browse to
openwrt-ipq40xx-linksys_ea6350v3-squashfs-factory.bin
- Click update.
- Read and accept the warning
- The router LED will start blinking. When the router LED goes solid, you
can now navigate to 192.168.1.1 to your new OpenWrt installation.
Sysupgrade:
- Flash the sysupgrade image as usual. Please: try to do a reset everytime
you can (doing it with LuCI is easy and can be done in the same step).
Recovery (Automatic):
- If the device fails to boot after install or upgrade, whilst the unit is
turned on:
1 - Wait 15 seconds
2 - Switch Off and Wait 10 seconds
3 - Switch on
4 - Repeat steps 1 to 3, 3 times then go to 5.
5 - U-boot will have now erased the failed update and switched back to the
last working firmware - you should be able to access your router on
LAN.
Recovery (Manual):
- The steps for manual recovery are the same as the generic u-boot tftp
client method.
Back To Stock:
- Use the generic recovery using the tftp client method to flash the
"civic.img". Also you can strip-and-pad the original image and use
the generic "mtd" method by flashing over the "kernel" partition.
* Just be careful to flash in the partition that the device is currently
booted.
Signed-off-by: Ryan Pannell <ryan@osukl.com>
Signed-off-by: Oever González <notengobattery@gmail.com>
[minor edits, removed second compatible of nand, added dtb entry to 4.19]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Copy U-Boot to STAGING_DIR_IMAGE (and append it to the EVA-image from
there) to fix image generation using the image-builder.
Also remove the bootloader from DEVICE_PACKAGES and instead use the
BUILD_DEVICES directive from within the U-Boot makefile.
This fixes eva-image generation using the OpenWRT image-builder.
Signed-off-by: David Bauer <mail@david-bauer.net>
The ZyXEL NBG6617 USB LED was not working with the default images.
It turned out that kmod-usb-ledtrig-usbport was missing from the
default installation.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This commit removes the fixed kernel size-padding for the Netgear
DNI image creation as it is not necessary for a working image.
The fake rootfs still needs to be padded to the blocksize.
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB
NOR: 32 MiB
ETH: Qualcomm Atheros QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button
LEDS: Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz
1. Load Ramdisk via U-Boot
To set up the flash memory environment, do the following:
a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters:
* 115200bps
* 8N1
b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown.
U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm
2. Load image via GUI
a. Upgrade EAP1300 to FW v3.5.3.2
In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade.
b. Transfer to OpenWrt from EnGenius.
In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin.
3. Revert to EnGenius EAP1300
To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration.
$ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin
Signed-off-by: Steven Lin <steven.lin@senao.com>
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and linux-firmware.git.
We switched to the upstream board-2.bin, hence the files can be removed
here.
Keep the ipq-wifi package in case new boards are added. It might take
some time till board-2.bins send upstream are merged.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
We select ath10k-ct by default, but it is still possible to build
the upstream version.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <john@phrozen.org>
The current make-ras.sh image generation script for the ZyXEL NBG6617
has portability issues with bash. Because of this, factory images are
currently not built correctly by the OpenWRT buildbots.
This commit replaces the make-ras.sh by C-written mkrasimage.
The new mkrasimage is also compatible with other ZyXEL devices using
the ras image-format.
This is not tested with the NBG6616 but it correctly builds the
header for ZyXEL factory image.
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 128 MB Nanya NT5CC64M16GP-DI
FLASH: 16 MiB Macronix MX25L12845EMI-12G
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: WPS, Mode-toggle-switch
LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS
(LAN not controllable by software)
(WLAN each green / red)
SERIAL: Header next to eth-phy.
VCC, TX, GND, RX (Square hole is VCC)
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet (Correct MAC-address)
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from tftp
- OpenWRT sysupgrade
- LEDs
- WPS Button
Not Working:
- Mode-toggle-switch
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command `tftpboot` will pull an initramfs image named
`C0A86302.img` from a tftp server at `192.168.99.08/24`.
After successfull transfer, boot the image with `bootm`.
To persistently write the firmware, flash an openwrt sysupgrade image
from inside the initramfs, for example transfer
via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device
with `sysupgrade -n /tmp/<sysupgrade>`.
append-cmdline patch taken from chunkeeys work on the NBG6617.
Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de>
Co-authored-by: David Bauer <mail@david-bauer.net>
Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
This commit adds an EVA flashable image for the FRITZ!Box 4040.
The image contains the U-Boot with OpenWRT appended to it. This way we
remove the need to use UART for initial flashing.
Signed-off-by: David Bauer <mail@david-bauer.net>
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-04-19.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Merge the two existing functions and use a parameter for the type
header field.
It updates the syntax of the former mpc85xx fake ramdisk header
command to be compatible with mkimage from u-boot 2018.03 and fixes the
build error spotted by the build bot.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Don't select the firmware with the board file, it prevents an easy use
of the -ct ath10k firmware. Select the firmware within the default
packages instead.
Remove the per device selection of the firmware now that it the
firmware is selected by default.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MB Winbond W632GU6KB12J
FLASH: 16 MiB Macronix MX25L12805D
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac
1x1 (EX6100)
2x2 (EX6150)
INPUT: Power, WPS, reset button
AP / Range-extender toggle
LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow
SERIAL: Header next to QCA8072 chip.
VCC, TX, RX, GND (Square hole is VCC)
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from WebIF
- Factory installation from tftp
- OpenWRT sysupgrade (Preserving and non-preserving)
- LEDs
- Buttons
Not Working:
- AP/Extender toggle-switch
Untested:
- Support on EX6100v2. They share the same GPL-Code and vendor-images.
The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz
board-blob. I only own a EX6150v2, therefore i am only able to verify
functionality on this device.
Install via Web-Interface:
Upload the factory image to the device to the Netgear Web-Interface.
The device might asks you to confirm the update a second time due to
detecting the OpenWRT firmware as older. The device will automatically
reboot after the image is written to flash.
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command "fw_recovery" will start a tftp server, waiting for
a DNI image to be pushed.
Assign your computer the IP-address 192.168.1.10/24. Push image with
tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY>
Device will erase factory-partition first, then writes the pushed image
to flash and reboots.
Parts of this commit are based on Thomas Hebb's work on the
openwrt-devel mailinglist.
See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds support for 8devices Jalapeno.
Specification:
QCA IPQ4018, Quad core ARM v7 Cortex A7 717MHz
256 MB of DDR3 RAM
8 MB of SPI NOR flash
128 MB of Winbond SPI NAND flash
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
requires special BDF in QCA4019/hw1.0/board-2.bin with:
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=8devices-Jalapeno
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
requires special BDF in QCA4019/hw1.0/board-2.bin with:
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=8devices-Jalapeno
ETH: Qualcomm Atheros QCA8072 Gigabit Switch (1 x LAN, 1 x WAN)
phy@mdio3:
Label: eth0
gmac0
phy@mdio4:
Label: eth1
gmac1
Installation instructions:
Since boards ship with old version of LEDE installation is simple.
Just use sysupgrade -n -F sysupgrade.bin
Syuspgrade needs to be forced since OpenWRT uses DT detection in recent
releases.
If you get error that FIT configuration is not found during boot it is
due to older U-boot used on your board.
That is because 8devices used custom FIT configuration partition name
as they internally had v1 and v2 boards.
Only v2 boards are sold so now they are shipping boards with never
U-boot using generic config@1 FIT partition name.
Also for old uboot it is possible to force loading config@1 by changing
uboot environment:
setenv boot5 'bootm 0x84000000#config@1’
saveenv
Signed-off-by: Robert Marko <robimarko@gmail.com>
The AVM Fritz!Box 4040 uses an IPQ4018 as SoC and not an IPQ4019. The DTS
must be adjusted to reflect this.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The OpenMesh A42 will use the default config entry in the FIT when no other
on is found but prefers the config@om.a42. This only becomes relevant when
a Multi-FIT image is prepared for this device.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* QCA IPQ4028
* 256 MB of RAM
* 32 MB of SPI NOR flash (mx25l25635e)
* 128 MB of SPI NAND flash (gd5f1gq4ucy1g)
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- uses AP-DK03 BDF from QCA4019/hw1.0/board-2.bin
* 2T2R 5 GHz
- QCA4019 hw1.0 (SoC)
- uses AP-DK03 BDF from QCA4019/hw1.0/board-2.bin
* 2 fully software controllable GPIO-LEDs
* 2 additional GPIO-LEDs which also affect the SIM card detection
* 1x button (reset)
* 1x GPIO buzzer
* 1x USB (xHCI)
* 1x NGFF (USB-only with Dual-SIM support, untested)
* TTL pins are on board (R124 is next to GND, then follows: RX, TX, VCC)
* 2x gigabit ethernet
- phy@mdio4:
+ Manual: Ethernet port 0
+ gmac0 (ethaddr) in original firmware
+ 802.3af POE (HV version)
+ 24v passive POE (LV version)
- phy@mdio3:
+ Manual: Ethernet port 1
+ gmac1 (eth1addr) in original firmware
* DC Jack connector
+ 24-56V (HV version)
+ 12-24V (LV version)
The SPI NAND flash isn't supported at the moment.
The bootloader has to be updated before OpenWrt is installed to fix a
reboot problem. The nor-ipq40xx-single.img from
https://downloads.compex.com.sg/?dir=uploads/QSDK/QCA-Reference/WPJ428/b170123-IPQ40xx-Reference-Firmware
has to be downloaded and the transfered in u-boot via TFTP
set ipaddr 192.168.1.11
set serverip 192.168.1.10
ping ${serverip}
tftpboot 0x84000000 nor-ipq40xx-single.img
imgaddr=0x84000000 && source $imgaddr:script
The sysupgrade image can be installed directly on flash using u-boot:
sf probe
tftpboot 0x84000000 openwrt-ipq40xx-compex_wpj428-squashfs-sysupgrade.bin
sf erase 0x00180000 +$filesize
sf write 0x84000000 0x00180000 $filesize
bootipq
The initramfs image can be started using
tftpboot 0x82000000 openwrt-ipq40xx-compex_wpj428-initramfs-fit-uImage.itb
set fdt_high 0x83000000
bootm 0x82000000
The used SIM card slot can be changed using
# slot 1 (also enables orange LED)
echo 1 > /sys/class/gpio/gpio3/value
# slot 2
echo 0 > /sys/class/gpio/gpio3/value
It can be checked whether a SIM card is inserted in the current slot and
the red LED is subsequently on via:
echo 2 > /sys/class/gpio/export
cat /sys/class/gpio/gpio2/value
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This patch adds support for Cisco Meraki MR33
hardware highlights:
SOC: IPQ4029 Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600 @ 627 MHz Micron MT41K128M16JT-125IT
NAND: 128 MiB SLC NAND Spansion S34ML01G200TFV00 (106 MiB usable)
ETH: Qualcomm Atheros AR8035 Gigabit PHY (1 x LAN/WAN) + PoE
WLAN1: QCA9887 (168c:0050) PCIe 1x1:1 802.11abgn ac Dualband VHT80
WLAN2: Qualcomm Atheros QCA4029 2.4GHz 802.11bgn 2:2x2
WLAN3: Qualcomm Atheros QCA4029 5GHz 802.11a/n/ac 2:2x2 VHT80
LEDS: 1 x Programmable RGB+White Status LED (driven by Ti LP5562 on i2c-1)
1 x Orange LED Fault Indicator (shared with LP5562)
2 x LAN Activity / Speed LEDs (On the RJ45 Port)
BUTTON: one Reset button
MISC: Bluetooth LE Ti cc2650 PG2.3 4x4mm - BL_CONFIG at 0x0001FFD8
AT24C64 8KiB EEPROM
Kensington Lock
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
1x4 0.1" header with half-height/low profile pins.
The pinout is: VCC (little white arrow), RX, TX, GND.
Flashing needs a serial adaptor, as well as patched ubootwrite utility
(needs Little-Endian support). And a modified u-boot (enabled Ethernet).
Meraki's original u-boot source can be found in:
<https://github.com/riptidewave93/meraki-uboot/tree/mr33-20170427>
Add images to do an installation via bootloader:
0. open up the MR33 and connect the serial console.
1. start the 2nd stage bootloader transfer from client pc:
# ubootwrite.py --write=mr33-uboot.bin
(The ubootwrite tool will interrupt the boot-process and hence
it needs to listen for cues. If the connection is bad (due to
the low-profile pins), the tool can fail multiple times and in
weird ways. If you are not sure, just use a terminal program
and see what the device is doing there.
2. power on the MR33 (with ethernet + serial cables attached)
Warning: Make sure you do this in a private LAN that has
no connection to the internet.
- let it upload the u-boot this can take 250-300 seconds -
3. use a tftp client (in binary mode!) on your PC to upload the sysupgrade.bin
(the u-boot is listening on 192.168.1.1)
# tftp 192.168.1.1
binary
put openwrt-ipq40xx-meraki_mr33-squashfs-sysupgrade.bin
4. wait for it to reboot
5. connect to your MR33 via ssh on 192.168.1.1
For more detailed instructions, please take a look at the:
"Flashing Instructions for the MR33" PDF. This can be found
on the wiki: <https://openwrt.org/toh/meraki/mr33>
(A link to the mr33-uboot.bin + the modified ubootwrite is
also there)
Thanks to Jerome C. for sending an MR33 to Chris.
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch adds support for ASUS RT-AC58U/RT-ACRH13.
hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 128 MiB DDR3L-1066 @ 537 MHz (1074?) NT5CC64M16GP-DI
NOR: 2 MiB Macronix MX25L1606E (for boot, QSEE)
NAND: 128 MiB Winbond W25NO1GVZE1G (cal + kernel + root, UBI)
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: one Reset and one WPS button
LEDS: Status, WAN, WIFI1/2, USB and LAN (one blue LED for each)
Serial:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has an unpopulated
1x4 0.1" header. The pinout (VDD, RX, GND, TX) is printed on the
PCB right next to the connector.
U-Boot Note: The ethernet driver isn't always reliable and can sometime
time out... Don't worry, just retry.
Access via the serial console is required. As well as a working
TFTP-server setup and the initramfs image. (If not provided, it
has to be built from the OpenWrt source. Make sure to enable
LZMA as the compression for the INITRAMFS!)
To install the image permanently, you have to do the following
steps in the listed order.
1. Open up the router.
There are four phillips screws hiding behind the four plastic
feets on the underside.
2. Connect the serial cable (See notes above)
3. Connect your router via one of the four LAN-ports (yellow)
to a PC which can set the IP-Address and ssh and scp from.
If possible set your PC's IPv4 Address to 192.168.1.70
(As this is the IP-Address the Router's bootloader expects
for the tftp server)
4. power up the router and enter the u-boot
choose option 1 to upload the initramfs image. And follow
through the ipv4 setup.
Wait for your router's status LED to stop blinking rapidly and
glow just blue. (The LAN LED should also be glowing blue).
3. Connect to the OpenWrt running in RAM
The default IPv4-Address of your router will be 192.168.1.1.
1. Copy over the openwrt-sysupgrade.bin image to your router's
temporary directory
# scp openwrt-sysupgrade.bin root@192.168.1.1:/tmp
2. ssh from your PC into your router as root.
# ssh root@192.168.1.1
The default OpenWrt-Image won't ask for a password. Simply hit the Enter-Key.
Once connected...: run the following commands on your temporary installation
3. delete the "jffs2" ubi partition to make room for your new root partition
# ubirmvol /dev/ubi0 --name=jffs2
4. install OpenWrt on the NAND Flash.
# sysupgrade -v /tmp/openwrt-sysupgrade.bin
- This will will automatically reboot the router -
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Rename the dts file to match the used SoC type and drop the unnecessary
KERNEL_INSTALL from the image build code.
Remove the fixed rootfs and kernel partitions and create an image with
rootfs appended after kernel.
Setup a switch portmap matching the hardware and a default network/switch
configuration to make make the second lan port working. Use eth0 as lan
to have it consistent accross the target.
Use the power LED to indicate the boot status.
Sort the SoC entries within the dts by address and use dtc labels
whenever possible.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This removes the block- and pagesize from the FritzBox 4040
image description, fixing incorrectly working sysupgrade.
With this commit, the default values for block- and pagesize are
used.
Signed-off-by: David Bauer <mail@david-bauer.net>
[chunkeey@gmail.com: removed 105-mtd-nor-add-mx25l25635f.patch as well]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Sort the soc entries in the dts by address and use dtc labels whenever
possible.
Adjust the DTS files, the OpenMesh A42 is actually an IPQ4018 and not an
IPQ4019.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
