Also remove vmlinuz-initramfs files from final imagebuilder image as
these file are not needed.
Fixes: c85348d9ab ("imagebuilder: remove initramfs image files")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Supports reading the same parameters currently being used by iwinfo.
Preparation for replacing iwinfo with a rewrite in ucode.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ALFA Network WiFi CampPro Nano Duo is a dual-radio Wi-Fi signal extender
(router) in USB dongle form-factor (Type-A plug is used only for power),
based on combination of two radio chipsets: Qualcomm QCA9531 (main SOC)
and MediaTek MT7610U (connected over USB 2.0 interface).
Specifications:
- SOC: QCA9531 v2 (650 MHz)
- DRAM: DDR2 128 MiB (Nanya NT5TU64M16HG-AC)
- Flash: 16 MiB SPI NOR (Macronix MX25L12835F)
- Ethernet: 1x 10/100 Mbps Ethernet (QCA9531)
- Wi-Fi: 2x2:2 2.4 GHz Wi-Fi 4 (QCA9531)
1x1:1 2.4/5 GHz Wi-Fi 5 (MT7610U)
- Antenna: 3x RP-SMA (female) antenna connectors
- LED: 1x orange (RJ45, power indicator)
2x green (status + RJ45 activity/link)
1x blue (Wi-Fi 2.4 GHz status)
- Button: 1x button (reset)
- UART: 1x 4-pin, 2.00 mm pitch header on PCB
- Other: external h/w watchdog (EM6324QYSP5B, enabled by default)
GPIO-controlled USB power for MT7610U
MAC addresses:
- LAN: 00:c0:ca:xx:xx:6d (art 0x2, -1)
- 2.4 GHz (QCA9531): 00:c0:ca:xx:xx:6e (art 0x2, device's label)
- 2.4/5 GHz (MT7610U): 00:c0:ca:xx:xx:6f (from eeprom)
Flash instructions:
You can use sysupgrade image directly in vendor firmware which is based
on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot:
1. Configure PC with static IP 192.168.1.2/24.
2. Connect PC with RJ45 port, press the reset button, power up device,
wait for first blink of status LED (indicates network setup), then
keep button for 3 following blinks and release it.
3. Open 192.168.1.1 address in your browser and upload sysupgrade image.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The larger switches of the Linksys LGS series (e.g. LGS352C) make
use of NAND. So the vendor firmware uses other commands to upload
an image through the WebUI.
Add the required scripts. With this we can upload an image to all
devices of that series. Independant of NOR or NAND.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/16711
Signed-off-by: Robert Marko <robimarko@gmail.com>
Instead of passing NULL to gpiochip_add_data, we can populate the
parameter and use gpiochip_get_data instead of a custom function.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16739
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Easier to just use devm_platform_ioremap_resource.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16701
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for the Cisco Meraki MX64 and MX65 devices which
use the Broadcom NSP SoC, which is compatible with the bcm53xx platform.
MX64 Hardware info:
- CPU: Broadcom BCM58625 Cortex A9 @ 1200Mhz
- RAM: 2 GB (4 x 4Gb SK Hynix H5TC4G83CFR)
- Storage: 1 GB (Micron MT29F8G08ABACA)
- Networking: BCM58625 internal switch (5x 1GbE ports)
- USB: 1x USB2.0
- Serial: Internal header
MX65 Hardware info:
- CPU: Broadcom BCM58625 Cortex A9 @ 1200Mhz
- RAM: 2 GB (4 x 4Gb SK Hynix H5TC4G83CFR)
- Storage: 1 GB (Micron MT29F8G08ABACA)
- Networking: BCM58625 switch (2x 1GbE ports, used for WAN ports 1 & 2)
2x Qualcomm QCA8337 switches (10x 1GbE ports, used for LAN ports 3-12)
- PSE: Broadcom BCM59111KMLG connected to LAN ports 11 & 12
- USB: 1x USB2.0
- Serial: Internal header
Notes:
- The Meraki provided GPL source are available at [2].
- Wireless capability on the MX64W and MX65W exists in the form of 2x
Broadcom BCM43520KMLG, which is not supported. These devices will work
otherwise as standard MX64 or MX65 devices.
- Early MX64 units use an A0 variant of the BCM958625 SoC which lacks
cache coherency and uses a different "secondary-boot-reg". As a
consequence a different device tree is needed.
- Installation of OpenWrt requires changing u-boot to a custom version.
This is due to the stock u-boot "nand read" command being limited to
load only 2MB, in spite of the bootkernel1 and bootkernel2 partitions
both being 3MB in the stock layout. It is also required to allow
booting via USB, enabling cache coherency and setting up the QCA
switches and Serdes link on the MX65. The modified sources for U-boot
are available for the MX64[3] and MX65[4].
- Initial work on this device used a small bootloader within the OEM
partition scheme. To allow booting of larger kernels, UBI and bootm
support has been added, along with ability to store env variables to
the NAND. The Shmoo and newly created env partitions have been moved
to the extra space available after the nvram data.
- Users who installed the previous non-UBI supporting bootloader will
need to convert to the new one before flashing a compatible image.
These steps are detailed below.
References:
[1] https://www.broadcom.com/products/embedded-and-networking-processors/c
ommunications/bcm5862x
[2] https://dl.meraki.net/wired-14-39-mx64-20190426.tar.bz2
[3] https://github.com/clayface/U-boot-MX64-20190430_MX64
[4] https://github.com/clayface/U-boot-MX64-20190430_MX65
Installation guide:
Initial installation steps:
1. Compile or obtain OpenWrt files for the MX64 or MX65, including
u-boot[3][4], initramfs and sysupgrade images.
2. A USB disk with DOS partition scheme and primary FAT partition is
required.
3. If installing onto an MX64, set up a local web server.
4. On the device, boot into diagnostic mode by holding reset when
powering on the device. Continue to hold reset until the orange LED
begins to flash white. On used units the white flash may be difficult
to see.
5. Plug an Ethernet cable into the first LAN port, set the host to
192.168.1.2 and confirm telnet connectivity to 192.168.1.1.
U-boot installation - MX64 Only:
1. Newer fw versions require extra steps to support OpenWrt. To check,
please connect via telnet and run:
`cat /sys/block/mtdblock0/ro`
If the result is 1, your mtd0 is locked will need to perform extra
steps 4 and 5 in this section. If the result is 0 then skip these.
2. Check which SoC is in use by running the following command:
`devmem 0x18000000`
If devmem is not found then try:
`devmem2 0x18000000`
If the output begins with anything between "0x3F00-0x3F03" you will
need to use the A0 release. For any other output, eg "0x3F04" or
higher, use the regular MX64 image.
3 Confirm the size of the device's boot(mtd0) partition. In most
cases it should be 0x100000 or larger. If this is the case, please
proceed to use the uboot_mx64 image. If the reported size is
0x80000, please use the uboot_mx64_small image, then follow the
later guide to change to the larger image.
`cat /proc/mtd`
Example output:
`# cat /proc/mtd
cat /proc/mtd
dev: size erasesize name
mtd0: 00100000 00040000 "boot"
mtd1: 00080000 00040000 "shmoo"
mtd2: 00300000 00040000 "bootkernel1"
mtd3: 00100000 00040000 "nvram"
mtd4: 00300000 00040000 "bootkernel2"
mtd5: 3f700000 00040000 "ubi"
mtd6: 40000000 00040000 "all"`
4. Set up a webserver to serve the appropriate uboot_mx64 from the
following location and verify the SHA512:
https://github.com/clayface/U-boot-MX64-20190430_MX64
5. (Only if mtd0 is locked) You will also need the mtd-rw.ko kernel
module to unlock the partition from the same repo. An mtd executable
is also needed to write the mtd block. Place these on the web server
as well.
6. (Only if mtd0 is locked) Use wget to retrieve the files on the MX64:
`wget http://192.168.1.2/mtd-rw.ko`
`insmod mtd-rw.ko i_want_a_brick=1`
and confirm the unlock is set with dmesg
`mtd-rw: mtd0: setting writeable flag`
7. Download the appropriate u-boot image according to step 3. If you
did not need to unlock the mtd0 partition then use dd to write the
file, with caution:
`wget http://192.168.1.2/uboot_mx64`
`dd if=uboot_mx64 of=/dev/mtdblock0`
If you needed to unlock the mtd0 partition using the mtd-rw module,
run these commands instead to install u-boot instead:
`wget http://192.168.1.2/mtd`
`chmod +x mtd`
`wget http://192.168.1.2/uboot_mx64`
`./mtd write uboot_mx64 /dev/mtd0`
8. Once this has successfully completed, power off the device. If you
did not need to install the small u-boot image, proceed to
"OpenWrt Installation". Otherwise proceed to "UBI supporting
bootloader installation".
U-boot installation - MX65 Only:
1. Obtain telnet access to the MX65.
2. Confirm the size of the device's boot(mtd0) partition. In most
cases it should be 0x100000 or larger. If this is the case, please
proceed to use the uboot_mx65 image. If the reported size is
0x80000, please use the uboot_mx65_small image, then follow the
later guide to change to the larger image.
`cat /proc/mtd`
3. Prepare a USB drive formatted to FAT. Download the appropriate
uboot_mx65 to the USB drive from the following location and verify
the SHA512:
https://github.com/clayface/U-boot-MX64-20190430_MX65
3. Once you have telnet access to the MX65, plug in the USB disk and
run the following commands, with caution. The USB disk should
automount but if it does not, you will need to power off and on
again with reset held. Depending on step 2, use the uboot_mx65 or
uboot_mx65_small image accordingly:
`cd /tmp/media/sda1`
`dd if=uboot_mx65 of=/dev/mtdblock0`
4. Once this has successfully completed, power off the device. If you
did not need to install the small u-boot image, proceed to
"OpenWrt Installation". Otherwise proceed to "UBI supporting
bootloader installation".
UBI supporting bootloader installation:
These steps need to be followed if the older u-boot image was
installed, either because the Meraki diagnostic partition scheme used
0x80000 as the mtd0 size, or because you installed the u-boot provided
while OpenWrt support was still under development. If using OpenWrt,
please make a backup before proceeding.
1. Obtain the relevant image from the MX64(A0) or MX65 u-boot repo:
`openwrt-bcm5862x-generic-meraki_XXXX-initramfs-kernel.bin`
2. With the USB drive already inserted, power on the device while
holding the reset button. A white/orange flashing pattern will
occur shortly after power on. Let go of the reset button. The
device is now booting into OpenWrt initramfs stored on the USB
disk.
3. Connect by SSH to 192.168.1.1 and flash the embedded u-boot image,
changing X as appropriate:
`mtd write /root/uboot_mx6X /dev/mtd0`
You do not need to reboot as this image can handle "Kernel-in-UBI"
OpenWrt installation.
4. You can proceed to obtain and flash the appropriate OpenWrt image
at "OpenWrt Installation" Step 3.
5. Reboot will take significantly longer due to Shmoo calibration. In
case the device does not come online after several minute, power-
cycle the device and see if it boots. If you see an orange/white
flashing pattern, this indicates UBI booting was not successful and
you will need to copy a new bcm53xx image to a USB disk before
booting it and attempting to install OpenWrt again - refer to
"OpenWrt Installation" step 1. Do not attempt to reflash u-boot in
this scenario.
OpenWrt Installation:
1. Having obtained an OpenWrt image, please copy the file
`openwrt-bcm53xx-generic-meraki_XXXX-initramfs.bin`
to the base directory of a FAT formatted USB drive using DOS
partition scheme ,where XXXX is mx64, mx64_a0 or mx65 depending on
which device you have.
2. With the USB drive already inserted, power on the device. Boot time
will be longer than usual while Shmoo calibration takes place. A
different white/orange flashing pattern will eventually occur to
indicate device is now booting into OpenWrt initramfs stored on the
USB disk.
3. Ensuring Ethernet is plugged into a LAN port with IP set in the
192.168.1.0/24 subnet excluding 192.168.1.1, use SCP to copy the
sysupgrade file to 192.168.1.1:/tmp, eg:
`scp openwrt-bcm53xx-generic-meraki_XXXX-squashfs.sysupgrade.bin\
192.168.1.1:/tmp`
4. Connect by SSH to 192.168.1.1 and run sysupgrade:
`sysupgrade \
/tmp/openwrt-bcm53xx-generic-meraki_XXXX-squashfs.sysupgrade.bin`
5. OpenWrt should now be installed on the device.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
[ Rebase kernel configuration for 6.6,
fix failsafe by making kmod-eeprom-at24 and kmod-dsa-qca8k built-in,
resolve conflicts,
add LED aliases,
fix eth0 MAC address at probe ]
TODO:
- fix multiple LED colors not applied despite aliases - due to custom
/etc/diag.sh
- fix race condition between preinit and probing of the DSA tree,
causing no network interface available in failsafe mode (in general
case - to allow moving drivers back to modules)
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable support for qca8k switch used in Meraki MX65. This is required to
properly support preinit networking on this device, otherwise unit won't
be accessible in failsafe mode.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is required for the AT24 EEPROM holding MAC address on Meraki
devices to probe before preinit starts, so all network devices can be
available at the preinit network setup starts
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Meraki MX6x devices use them to store MAC address, so it is required to be
built-in for networking to probe properly, before preinit network setup
happens, which in turn is required for proper failsafe mode access.
Enable CONFIG_EEPROM_AT24 for the target.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch is required to support reading MAC address on Meraki MX64/65
line of devices, but also touches MR32, so let's backport it first.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds "REQUIRE_IMAGE_METADATA=1" requirement for the MR26 and
MR32, with REQUIRE_IMAGE_METADATA explicitly 0 elsewhere. This is based
upon bcm63xx's base-files/lib/upgrade/platform.sh.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16634
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Oversight from 8d302f5ebc , which requires
this to work. I couldn't test it as I ended up wiping my UBI volume by
accident.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16580
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is needed in order to get a MAC address from UBI.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16580
Signed-off-by: Robert Marko <robimarko@gmail.com>
linux,ubi expects the volname variable, not volume.
This will fix NVMEM-on-UBI.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16580
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since kernel_oldconfig doesn't work properly with it, I ran that first
and then moved all the config symbols to config-6.6 and found the
differences.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16580
Signed-off-by: Robert Marko <robimarko@gmail.com>
make kernel_oldconfig doesn't seem to work with this. Handle manually.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16580
Signed-off-by: Robert Marko <robimarko@gmail.com>
Adjusts the default config to modern kernels.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16580
Signed-off-by: Robert Marko <robimarko@gmail.com>
The ImageBuilder when using the profile for the OpenWrt One has been
failing because the initramfs image included in the ubinized image could
not be found.
Fix that by using the staged initramfs instead when using the
ImageBuilder.
Fixes: 797904b3cb ("mediatek/filogic: add OpenWrt One support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This allows to obtain detailed diagnostic information about the DSL
connection from the modem. The script is copied from the corresponding
packages for VDSL modems.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20241019174041.1281093-4-jan@3e8.eu/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a preparation for adding support for dsl_cpe_pipe.sh with a
similar set of commands compared to the VDSL variant.
The configuration is simplified by using the "--enable-model" option.
Other options are chosen to match the VDSL variant, while also making
sure that previously enabled options stay like that. However, ReTx
options stay disabled, because of incompatibility with the ubus code.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20241019174041.1281093-3-jan@3e8.eu/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is a preparation for adding support for dsl_cpe_pipe.sh with a
similar set of commands compared to the VDSL variant.
The configuration is simplified by using the "--enable-model" option.
Other options are chosen to match the VDSL variant, while also making
sure that previously enabled options stay like that. However, ReTx
options stay disabled, because of incompatibility with the ubus code.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20241019174041.1281093-2-jan@3e8.eu/
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
65bb027 CMakeLists.txt: bump minimum cmake version
252a9b0 libubus: Make UBUS_* macros work cleanly in C++
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds the build date during compilation to the os-release file.
This information can then be used later to output this via the the ubus,
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/15987
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Introduce EN7581 SoC support with currently rfb board supported.
This is a new 64bit SoC from Airoha that is currently almost fully
supported upstream with only the DTS missing. Setting source-only
waiting for the full upstream support to be completed.
Link: https://github.com/openwrt/openwrt/pull/16730
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport alloc_netdev_dummy patch from upstream needed for new Airoha
EN7581 SoC.
Refresh all affected patch with make target/linux/refresh.
Link: https://github.com/openwrt/openwrt/pull/16730
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
In preparation for EN7581 SoC support, move en7523 in dedicated
subtarget.
This is needed as EN7581 is now 64bit but en7523 is 32bit hence have
very different kernel config.
Also rename patch to a more friendly number sequence.
Link: https://github.com/openwrt/openwrt/pull/16730
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
COMFAST CF-E355AC v2 is a ceiling mount AP with PoE support,
based on Qualcomm/Atheros QCA9531 + QCA9886.
Short specification:
- 1x 10/100 Mbps Ethernet, with PoE support (wan/eth1)
- 1x 10/100/1000 Mbps Ethernet, with PoE support (lan/eth0)
- 128MB of RAM (DDR2)
- 16 MB of FLASH
- 2T2R 2.4 GHz, 802.11b/g/n (wlan2g)
- 2T2R 5 GHz, 802.11ac/n/a, WAVE 2 (wlan5g)
- built-in 4x 3 dBi antennas
- output power (max): 500 mW (27 dBm)
- 1x RGB LED, 1x button
- separate watchdog chip via GPIO (bottom of PCB?)
- UART header on PCB with proper labelling
Markings on PCB:
* R121QH_VER2.1 (silkscreen, bottom)
* CF-WA800 (sticker, top)
Initial flashing instructions:
Original firmware is based on OpenWrt.
a) Use sysupgrade image directly in vendor GUI.
b) Or via tftp:
ipaddr=192.168.1.1
serverip=192.168.1.10
bootfile="firmware.bin"
c) Or possibly via u-boot's `httpd` command.
MAC-address mapping follows original firmware:
* eth1 (wan) is the lowest mac address (art @ 0x0)
* eth0 (lan) uses eth1 + 1 (art @ 0x1002)
* wlan2g (phy1) uses eth1 + 2 (art @ 0x06)
* wlan5g (phy0) uses eth1 + 10 (not present in art)
* unused MAC (eth1 + 3) (art @ 0x5006)
Art dump (`hexdump /dev/mtd1 |grep ZZZZ`):
0000000 ZZZZ XXXX XXX0 ZZZZ XXXX XXX2 ffff ffff
0001000 0202 ZZZZ XXXX XXX1 0000 0000 0000 0000
0005000 202f bd21 0101 ZZZZ XXXX XXX3 0000 2000
Root access to original firmware (only via UART) can be achieved by
making a backup of configuration from web interface. Backup contains
whole `/etc` directory...
Signed-off-by: Priit Laes <plaes@plaes.org>
Link: https://github.com/openwrt/openwrt/pull/16556
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
don't use configuration directories which are relative
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14975
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add support for handling of DNS RR (Resource Records) requests, which
are needed for the HTTPS Type 65 records, introduced to support the
DNS-based Service Discovery (DNS-SD) mechanism for HTTPS services and
defined in the RFC 9460 (9.1. Query Names for HTTPS RRs).
Ref: https://forum.openwrt.org/t/resolving-query-type-65-to-local-address-for-ios-clients-in-dnsmasq/179504/11
uci config usage:
config dnsrr
option rrname 'foo.example.com'
option rrnumber '65'
option hexdata '00'
hexdata is optional.
Available since dnsmasq 2.62 (for around 12 years at this point).
Note: dnsmasq dns-rr are not affected by filter-rr
Tested on 22.03.5
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Tested-by: Vladimir Kochkovski <ask@getvladimir.com>
Link: https://github.com/openwrt/openwrt/pull/14975
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Prevents problems when variables contain spaces.
Tested on: 23.05.3
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14975
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Users can now freely add new dnsmasq parameters (i.e. a whole config)
via extraconf. This means users can add their own parameters without
changes to init or GUI.
Co-opted the default of confdir also to include the instance name.
This way each instance gets its own .d directory (and separate instances
do not all inherit the same 'extraconftext').
Usage:
config dnsmasq 'config'
...
option extraconftext 'cache-size=2048\nlog-async=20'
config dnsmasq 'blah'
...
option extraconftext 'cache-size=128\nlog-async=5'
or even (which would produce staggered output but still valid)
config dnsmasq 'blah'
...
option extraconftext 'cache-size=128
log-async=5'
See https://forum.openwrt.org/t/add-dnsmasq-custom-options-field-in-luci-gui/193184
Tested on: 23.05.3, 22.03.6
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Tested-by: Vladimir Kochkovski <ask@getvladimir.com>
Link: https://github.com/openwrt/openwrt/pull/14975
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
dnsmasq v2.90 introduced `--cache-rr=<rrtype>[,<rrtype>...]`.
uci config usage:
config dnsmasq
...
option cache_rr 'AAAA,CNAME,NXDOMAIN,SRV,...'
The dnsmasq instance internally builds a linked list of RR to cache
from the individually supplied parameters, so it's allowed to provide
multiples:
... --cache-rr=AAAA --cache-rr=A ...
See https://forum.openwrt.org/t/resolving-query-type-65-to-local-address-for-ios-clients-in-dnsmasq/179504
Tested on: 23.05.2
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Tested-by: Vladimir Kochkovski <ask@getvladimir.com>
Link: https://github.com/openwrt/openwrt/pull/14975
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
dnsmasq v2.90 introduced `--filter-rr=<rrtype>[,<rrtype>...]`.
uci config usage:
config dnsmasq
...
option filter_rr 'AAAA,CNAME,NXDOMAIN,SRV,...'
The dnsmasq instance internally builds a linked list of RR to filter
from the individually supplied parameters, so it's harmless to provide
synonyms:
... --filter-A --filter-rr=A ...
See https://forum.openwrt.org/t/resolving-query-type-65-to-local-address-for-ios-clients-in-dnsmasq/179504/23
Tested on: 23.05.2
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Tested-by: Vladimir Kochkovski <ask@getvladimir.com>
Link: https://github.com/openwrt/openwrt/pull/14975
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch allows the use of SAE when using PPSK after
https://w1.fi/cgit/hostap/commit/?id=fcbdaae8a52e542705a651ee78b39b02935fda20
added support for it.
It also implements a fix so that this option works with SAE. The reason this
doesn't work out of the box is because OpenWRT deviates from hostapd defaults
by setting `sae_pwe` option to 2 which makes this mode not function properly
(results in every auth attempt being denied).
That issue was addressed by not overriding hostapd's default for the `sae_pwe`
option when the PPSK option is in use. This should be fine because hostapd's
test cases specifically test this mode with the default SAE parameters. See:
https://w1.fi/cgit/hostap/commit/?id=c34b35b54e81dbacd9dee513b74604c87f93f6a3
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/16343
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix conditions for handling offloaded packets
Fixes: #13430
Signed-off-by: Leon M. Busch-George <leon@georgemail.eu>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
