Disable video and input drivers - they are needed only for one
board and can be enabled via modules if/when UI will be available.
Use LED drivers from packages.
Cleanup other things unnecessarily overriding defaults.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
This adds the patches to get fairly complete Gemini support
using kernel v4.14. It is mainly a backport of patches from
kernel v4.16 with omissions of things like graphics that require
substantial changes and will be better handled once we move
to the v4.16 kernel proper.
On top of this are some WIP patches for USB support.
Tested on Raidsonic NAS4220B and D-link DNS-313.
ChangeLog v4->v5:
- Fix ethernet single gmac usecase
- Fix USB reset (patch from Hans)
- Fix Raidsonic ethernet skew delay
- Fix kernel config (bridge, squashfs, jffs2, usb)
- Disable second usb port on Raidsonic board until fotg210_hcd is fixed
ChangeLog v3->v4:
- Make sure to use tabs rather than spaces in base-files.
- Use the dns313 image tool from the firmware-utils.
- Break out the addition of the v4.14 patches and the removal
of the v4.4 patches to separate (big) patches.
ChangeLog v2->v3:
- Update the kernel config as indicated by Hauke Martens:
- Regenerate again after rebasing using kernel_oldconfig
dropping a few optimization settings that are now generic
- Drop CFG80211 stuff (module)
- Drop CIFS stuff (module)
- Drop MAC80211 (module)
- Drop wireless drivers (module)
- Enabled OverlayFS
- Added proper DNS-313 boot image generation with the special
file header tool.
- Disable CMA in the kernel
- Enable LZMA compression of the kernel
- Consequently name the nas4220b images nas4220b
- Update preinit MAC detection script to handle also DNS-313
- Add board.d/03_hdparm to set the disk to spin down after
1 minute by default, if we have the hdparm tool installed
ChangeLog v1->v2:
- Processed config through kernel_oldconfig
- Processed patches through make target/linux/{clean,refresh} V=99
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Add target device as at91-sama5d2_ptc_ek in SAMA5D2 subtarget and
build images for SAMA5D2 PTC Ek board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
reorganizing at91 subtargets based on sama5 soc features and this fix
below problems.
1. able to set neon flags to sama5d2 & sama5d4 subtargets.
2. fix the make clean which removes all the subtargets in bin folder.
3. able to configure kernel specific to subtarget.
4. able to set vfpu4 flags to samad3 subtargets.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
creating sdcard image with ext4 rootfs only and ignoring creating
other filesystem in sdcard image.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Add support for SAMA5D27 SOM1 with target device as at91-sama5d27_som1_ek
in SAMA5 subtarget and build images for SAMA5D27 SOM1 Ek board.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
copying at91bootstrap and uboot binaries to sdcard image is done
based on device name instead of dts name and this avoids creating
multiple u-boot and at91bootstrap binaries.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
In typical OpenWrt setups, there are no other users that have a shell spawned for them by default.
This can be overriden by the kernel.dmesg_output syssctl.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
sama5d2 & samad4 have neon feature and sama5d3 does not have neon
feature due to which sama5d3 boot fails with error message Kernel
panic - not syncing: Attempted to kill init! exitcode=0x00000004.
removing neon & VFPv4 support to fix this
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
when external kernel is selected from menuconfig, device wb50n is not
avaliable and build fails. As a fix adding checks for external kernel.
Signed-off-by: Sandeep Sheriker Mallikarjun <sandeepsheriker.mallikarjun@microchip.com>
Kernel support already present.
Patch adds userspace for the 'iLS' suffix model of the RB2011 family.
Enables correct initial switch settings, sysupgrade, etc.
https://mikrotik.com/product/RB2011iLS-IN
Signed-off-by: Simon Paterson <simon.paterson.nz@gmail.com>
The harden branch predictor was backported for arm64 with 4.9.92-96.
Fixes: 9aa196e0f2 ("kernel: bump 4.9 to bump 4.9.96")
Signed-off-by: Mathias Kresin <dev@kresin.me>
This is mainly a bug fix for multi-core MIPS systems where L1 caches besides the primary do not get flushed.
The most obvious problem is data corruption on SATA and USB devices where read requests are typically larger than the cacheline size.
This may also fix ar71xx systems that suffer from similar data corruption but I have not tested if it does.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Some Ubiquiti U-boot versions, in particular the "U-Boot 1.1.4.2-s956
(Jun 10 2015 - 10:54:50)" found with AirOS 5.6, do not correctly flush the
caches for the whole kernel address range after decompressing the kernel
image, leading to hard to debug boot failures, depending on kernel version
and configuration.
As a workaround, prepend the relocate-kernels loader, which will invalidate
the caches after moving the kernel to the correct load address.
Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
There is no pinmux group "jtag" for mt7628 and the pinmux driver fails
to load due to the use of the not existing group.
Fixes: FS#1515
Signed-off-by: Mathias Kresin <dev@kresin.me>
The old DTB method (OWRTDTB) is not recognized by the boot process
anymore with 4.9/4.14.
This patch reuses KERNEL_DTB to get a valid DTB applied to the kernel
image.
Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
The current option driver binds to the usb interface 2,3,4,5.
But the interface 4 and 5 doesn't answer to the AT commands.
On the new openwrt configuration the wwan script select the 5th
interface as control interface, failing to establish the
3G connection.
Backport the fix for the problem.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
* QCA IPQ4019
* 256 MB of RAM
* 32 MB of SPI NOR flash (s25fl256s1)
- 2x 15 MB available; but one of the 15 MB regions is the recovery image
* 2T2R 2.4 GHz
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62
* 2T2R 5 GHz (channel 36-64)
- QCA9888 hw2.0 (PCI)
- requires special BDF in QCA9888/hw2.0/board-2.bin
bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62
* 2T2R 5 GHz (channel 100-165)
- QCA4019 hw1.0 (SoC)
- requires special BDF in QCA4019/hw1.0/board-2.bin with
bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62
* multi-color LED (controlled via red/green/blue GPIOs)
* 1x button (reset; kmod-input-gpio-keys compatible)
* external watchdog
- triggered GPIO
* 1x USB (xHCI)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x gigabit ethernet
- phy@mdio3:
+ Label: Ethernet 1
+ gmac0 (ethaddr) in original firmware
+ 802.3at POE+
- phy@mdio4:
+ Label: Ethernet 2
+ gmac1 (eth1addr) in original firmware
+ 18-24V passive POE (mode B)
* powered only via POE
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the factory image to the u-boot when the device boots up.
The initramfs image can be started using
setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)'
tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb
set fdt_high 0x85000000
bootm 0x84000000
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
The pinctrl initialization fails with the MSM pinctrl code and gpio-hogs
because either the gpio ranges are not yet initialized (missing gpio-range
in DT) or that the msm driver unconditionally tries to re-initializes the
ranges (gpio-range in DT).
To allow gpio-hogs and similar early-boot gpio code, the gpio-ranges must
be in the device tree and the pinctrl-msm code must check whether the range
was already initialized by the DT.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
[drop changes to unrelated dtsi files, refresh patches]
Signed-off-by: Mathias Kresin <dev@kresin.me>
The BDFs for all boards were upstreamed to the ath10k-firmware
repository and are now part of ath10k-firmware 2018-04-19.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
These devices have only one ethernet port. It doesn't make sense to
expose the unused GMACs as separate network devices.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
The tz and smem reserved-memory information handled in the upstream Linux
sources by the SoC specific dtsi and not by the the boards dts. Using the
same approach in OpenWrt avoids unneccessary duplication.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
The reserved-memory regions are mostly undocumented by QCA and are named
very unspecific in the QSDK device trees. It was tried to clean them up by
commit 71ed9f10a3 ("ipq40xx: Use detailed reserved memory for A42") and
similar changes.
The features which require these regions were mostly unknown but
Senthilkumar N L <snlakshm@qti.qualcomm.com> and Sricharan Ramabadhran
<srichara@qti.qualcomm.com> provided some more insight in some of them:
* crash dump feature
- a couple of regions used when 'qca,scm_restart_reason' dt node has the
value 'dload_status' not set to 1
+ apps_bl <0x87000000 0x400000>
+ sbl <0x87400000 0x100000>
+ cnss_debug <0x87400000 0x100000>
+ cpu_context_dump <0x87b00000 0x080000>
- required driver not available in Linux
- safe to remove
* QSEE app execution
- region tz_apps <0x87b80000 0x280000>
- required driver not available in Linux
- safe to remove
* communication with TZ/QSEE
- region smem <0x87b80000 0x280000>
- driver changes not yet upstreamed
- must not be removed because any access can crash kernel/program
* trustzone (QSEE) private memory
- region tz <0x87e80000 0x180000>
- must not be removed because any access can crash kernel/program
Removing the unnecessary regions saves some kilobyte of reserved-memory and
cleans up the device tree:
* 2560 KiB
- 8devices Jalapeno
- AVM FRITZ!Box 4040
- Compex WPJ428
- Meraki MR33 Access Point
- OpenMesh A42
* 14336 KiB
- GL.iNet GL-B1300
- Qualcomm Technologies, Inc. IPQ40xx/AP-DK01.1-C1
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Merge the two existing functions and use a parameter for the type
header field.
It updates the syntax of the former mpc85xx fake ramdisk header
command to be compatible with mkimage from u-boot 2018.03 and fixes the
build error spotted by the build bot.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This reverts commit 5555545494.
The target supports both NEON and VFPv4, but for this to work properly,
a few more changes are needed:
- enable NEON support in the kernel config
- add the fpu feature flag to the makefile
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The stats update needs to protect against being interrupted by a tasklet
The u64 stats seqlock needs to be initialized
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The pins are used as (LED) GPIOs and can't be used at the same time as
hardware controlled ephy (LED) pins.
Fixes: FS#1500
Signed-off-by: Mathias Kresin <dev@kresin.me>
In the new USB phy driver, it checks the compatible string before
attempting to iomap its mem resource and do the extra PHY init
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The MX60's uboot disables all the PHYs before starting linux.
This causes the PHY/switch detection code to malfunction
almost all of the time. To get around this, set a compatible
flag to force PHYID.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
Don't select the firmware with the board file, it prevents an easy use
of the -ct ath10k firmware. Select the firmware within the default
packages instead.
Remove the per device selection of the firmware now that it the
firmware is selected by default.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MB Winbond W632GU6KB12J
FLASH: 16 MiB Macronix MX25L12805D
ETH: Qualcomm QCA8072
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac
1x1 (EX6100)
2x2 (EX6150)
INPUT: Power, WPS, reset button
AP / Range-extender toggle
LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow
SERIAL: Header next to QCA8072 chip.
VCC, TX, RX, GND (Square hole is VCC)
WARNING: The serial port needs a TTL/RS-232 v3.3 level converter!
The Serial setting is 115200-8-N-1.
Tested and working:
- Ethernet
- 2.4 GHz WiFi (Correct MAC-address)
- 5 GHz WiFi (Correct MAC-address)
- Factory installation from WebIF
- Factory installation from tftp
- OpenWRT sysupgrade (Preserving and non-preserving)
- LEDs
- Buttons
Not Working:
- AP/Extender toggle-switch
Untested:
- Support on EX6100v2. They share the same GPL-Code and vendor-images.
The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz
board-blob. I only own a EX6150v2, therefore i am only able to verify
functionality on this device.
Install via Web-Interface:
Upload the factory image to the device to the Netgear Web-Interface.
The device might asks you to confirm the update a second time due to
detecting the OpenWRT firmware as older. The device will automatically
reboot after the image is written to flash.
Install via TFTP:
Connect to the devices serial. Hit Enter-Key in bootloader to stop
autobooting. Command "fw_recovery" will start a tftp server, waiting for
a DNI image to be pushed.
Assign your computer the IP-address 192.168.1.10/24. Push image with
tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY>
Device will erase factory-partition first, then writes the pushed image
to flash and reboots.
Parts of this commit are based on Thomas Hebb's work on the
openwrt-devel mailinglist.
See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds support for 8devices Jalapeno.
Specification:
QCA IPQ4018, Quad core ARM v7 Cortex A7 717MHz
256 MB of DDR3 RAM
8 MB of SPI NOR flash
128 MB of Winbond SPI NAND flash
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
requires special BDF in QCA4019/hw1.0/board-2.bin with:
bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=8devices-Jalapeno
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
requires special BDF in QCA4019/hw1.0/board-2.bin with:
bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=8devices-Jalapeno
ETH: Qualcomm Atheros QCA8072 Gigabit Switch (1 x LAN, 1 x WAN)
phy@mdio3:
Label: eth0
gmac0
phy@mdio4:
Label: eth1
gmac1
Installation instructions:
Since boards ship with old version of LEDE installation is simple.
Just use sysupgrade -n -F sysupgrade.bin
Syuspgrade needs to be forced since OpenWRT uses DT detection in recent
releases.
If you get error that FIT configuration is not found during boot it is
due to older U-boot used on your board.
That is because 8devices used custom FIT configuration partition name
as they internally had v1 and v2 boards.
Only v2 boards are sold so now they are shipping boards with never
U-boot using generic config@1 FIT partition name.
Also for old uboot it is possible to force loading config@1 by changing
uboot environment:
setenv boot5 'bootm 0x84000000#config@1’
saveenv
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is important fix for flash parsing in some corner cases. In case
of TRX subpartition with rootfs being aligned to the flash block size it
was incorrectly registered twice. Detecting & registering it as a
standalone partition was resulting in an incorrect "firmware" partition
size and possibly broken sysupgrade.
It wasn't noticed before because "rootfs" alignment depends on a kernel
size. It can happen though - depending on the configuration and the
kernel size.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Previously, tplink_pharos_check_image() would accept any image with ELF
magic and only non-printable data in the support-list, as in this case the
while-read loop would not run at all. Add the new support-list offset and
ensure an image is only accepted when the model string is actually found.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Some Airmax devices can establish a Gigabit link even though the MAC only
supports 10/100 MBit/s, leading to broken connectivity. Prevent this from
happening by limiting the speed to 100MBit/s.
Fixes: FS#296
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This solution is more upstream compatible as it only requires specifying
of_match_table in the parser code and doesn't depend on linux,part-probe
which is solution made generic by a LEDE downstream patch that can't be
upstreamed.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Acked-by: John Crispin <john@phrozen.org>
These patches were finally accepted and are already present in the
Linus's tree. This should be good enough to make is "backport" material.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
With kernel 4.14 the OpenWrt specific module name collides with the
upstream added module for Mediatek ARM Socs.
During addition of preliminary support for kernel 4.14, the config
symbol used by the out of tree driver was already renamed but the ramips
kernel package wasn't updated.
Fix the build error by updating the config and kernel module name for
the kernel package.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The Zorlik ZL5900V2 is an unbranded clone of HAME MPR-A1/2. It is
marketed as "3G Wi-Fi Router". Only the PCB has the model name
"ZL5900V2" printed on it.
Specifications:
- Ralink RT5350F (360 MHz)
- 32 MB RAM
- 8 MB Flash
- 802.11bgn 1T1R
- 1x 10/100 Mbps Ethernet
- 1x USB 2.0 (Type-A)
- 5200 mAh battery
The ramdisk image (not the squashfs sysupgrade image) can be flashed
through the web interface (named "GoAhead") of the factory firmware.
However, as the factory firmware does not cleanly unmount the rootfs
before flashing, the device may hang instead of rebooting after
successful write. Power cycling the device gets you in OpenWrt where
the squashfs image may be flashed through normal sysupgrade procedure.
Signed-off-by: Vianney le Clément de Saint-Marcq <code@quartic.eu>
YouHua tech WR1200JS is an AC1200 router with 5 1Gb ports (4 Lan, 1 Wan)
and 1 USB 2.0 port.
Devices is base on MediaTek MT7621AT + MT7603E + MT7612E.
Specification:
- MT7612AT (880 MHz)
- 128 MB of RAM
- 16 MB of FLASH (SPI NOR)
- 5x 10/100/1000 Mbps Ethernet
- 2T2R 2.4 GHz (MT7603E)
- 2T2R 5 GHz (MT7612E)
- 1x USB 2.0
- 10x LED (Power 2G 5G WPS Internet LAN4-1 USB)
- 3x button (reset wifi wps)
- DC jack for main power input (12V)
Installation:
1.) Press reset key 5 sec and restore the factory default
2.) Login webUI and change username to root and set a
new password
3.) Visit http://192.168.2.254/adm/telnetd.shtml and
turn on the telnet service
4.) Copy openwrt-ramips-mt7621-youhua_wr1200js-initramfs-kernel.bin
to a usb pan
5.) Plug the usb pan to the router, telnet to the router
and login by root
6.) cd /media/sda1 and check the initramfs file is there
7.) exec command:
mtd_write write openwrt-ramips-mt7621-youhua_wr1200js-initramfs-kernel.bin Kernel
8.) reboot and visit 192.168.1.1
Signed-off-by: Zheng Qian <sotux82@gmail.com>
The previous fw version require the replacement of the stock bootloader
with u-boot. This prevent an easy stock restore of the original fw.
Now a proper fw util has been developed to manage the stock jboot
bootloader. Therefore make sense have a fw image for the stock
bootloader.
The old fw configuration (u-boot) is not compatible with the new one
and will not be supported anymore.
So at the end 2 image can be generated:
1) factory image with jboot bootloader
openwrt-ramips-rt305x-dwr-512-b-squashfs-factory.bin
2) sysupgrade image with jboot bootloader
openwrt-ramips-rt305x-dwr-512-b-squashfs-sysupgrade.bin
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
The Ralink USB PHY driver merged into mainline has a slightly different
device tree binding than the patch that was used with linux 4.9.
The new driver requires a `ralink,sysctl` node pointing to the `syscon`
node.
This patch also sets `#phy-cells` to 0, as recommended by the mainline
documentation [1].
[1] Documentation/devicetree/bindings/phy/ralink-usb-phy.txt
Signed-off-by: Vianney le Clément de Saint-Marcq <code@quartic.eu>
TP-Link Archer C60 v2 is a dual-band AC1350 router, based on
Qualcomm/Atheros QCA9561 + QCA9886.
Specification:
- 775/650/258 MHz (CPU/DDR/AHB)
- 64 MB of RAM (DDR2)
- 8 MB of FLASH (SPI NOR)
- 3T3R 2.4 GHz
- 2T2R 5 GHz
- 5x 10/100 Mbps Ethernet
- 7x LED, 2x button
- UART header on PCB
Flash instruction (web):
Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and use
OEM System Tools - Firmware Upgrade site.
Flash instruction (recovery):
1. Set PC to fixed IP address 192.168.0.66
2. Download lede-ar71xx-generic-archer-c60-v2-squashfs-factory.bin and
rename it to tp_recovery.bin
3. Start a tftp server with the file tp_recovery.bin in its root
directory
4. Turn off the router
5. Press and hold reset button
6. Turn on router with the reset button pressed and wait ~15 seconds
7. Release the reset button and after a short time the firmware should
be transferred from the tftp server
8. Wait ~30 second to complete recovery
Flash instruction (under U-Boot, using UART):
tftp 0x81000000 lede-ar71xx-...-sysupgrade.bin
erase 0x9f030000 +$filesize
cp.b $fileaddr 0x9f030000 $filesize
reset
Signed-off-by: Henryk Heisig <hyniu@o2.pl>
Add support for TL-WR940N v6 board. It is pretty much the same as v5
except they only left WAN LED and removed other ones.
Installation: flash factory image through WEB UI or use TFTP.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rework (again) platform support for dual-role chipidea USB controller:
- include support for QCA9531
- use correct EHCI block size
- drop ar933x_usb_setup_ctrl_config() function
- simplify code after previous "register chipidea only in device mode"
change (fa22714181)
Reworked patch was tested on devices with below QCA WiSOCs (signal/GPIO
name with required bootstrap state for USB bus 0 in device mode):
- AR9331 (GPIO13 pull-down)
- AR9342 (RGMII_TXD1/ETXD1 pull-up)
- AR9344 (GPIO20 pull-up)
- QCA9531 (GPIO13 pull-up)
- QCA9558 (GPIO13 pull-up)
The only way to select device mode for bus 0 is to change SOC bootstrap
configuration which is sampled only once, at hard reset. Likely, other
models, like QCA9556 or AR9341, should also support dual-role USB mode
but they were not tested.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Supports IPv4 flow offloading on MT7621 for Routing, SNAT and DNAT
Supported are regular ethernet->ethernet connections, including one
802.1q VLAN and/or PPPoE encapsulation
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
of_dma_configure() sets a default ->dma_mask of
DMA_BIT_MASK(32), claiming devices can DMA from
the full 32bit address space.
The mtk-mmc driver does not support access to
highmem pages, so it is really limited to the
bottom 512M (actually 448M due to 64M of IO space).
Setting ->dma_mask to NULL causes mmc_setup_queue()
to fall-back to using BLK_BOUNCE_HIGH to tell the
block layer to use a bounce-buffer for any highmem
pages requiring IO.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
- avoid using garbage stack values as dst pointer if lookup fails
- provide the source address for ipv6 dst lookup
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Our .dts files only have one device defined and this is unlikely to
change, so statically initialize host->id to 0.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This commit adds correct model detection for UniFi
AC-Mesh. Previously said device was incorrectly detected
as UniFi AC-Lite.
The Information about the device is stored at 0xC in the EEPROM
partition. It corresponds to the sysid in /etc/board.info of the
Ubiquiti stock firmware.
Signed-off-by: David Bauer <mail@david-bauer.net>
D-Link DAP-1330 rev. A1 is a wall-plug N300 Wi-Fi range extender,
based on Qualcomm/Atheros QCA9533 v2.
Short specification:
- 650/393/216 MHz (CPU/DDR/AHB)
- 1x 10/100 Mbps Ethernet
- 64 MB of RAM (DDR1)
- 8 MB of FLASH
- 2T2R 2.4 GHz
- 2x external antennas
- 6x LED (2 are bi-color), 2x button
- 4 pin on pcb (looking from eth port and from left to right tx,rx,gnd,vcc)
Flash instruction: use "factory" image directly in vendor GUI.
This device has a recovery system that assign the ip addr of env
variable "serverip" via dhcp to a pc, and the "ipaddr" value to itself.
The recovery it's triggered by a not bootable firmware,
or pressing the reset button during the bootloader startup (first 30 seconds).
The recovery uses a http page to restore the firmware, and it's checking
the firmware image header, so use the "factory" image to
restore or the original firmware.
You can access vendor firmware over serial using:
- login: root
- password: linuxrocks
Image was tested only in EU version of the device, but should work
also with the same device version sold in other countries.
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
It was wrong from the beginning and the trigger for the wan led was
never set due to the typo.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
[add commit message]
Signed-off-by: Mathias Kresin <dev@kresin.me>
We need to reset the GPHYs on reboot as well. Otherwise the bootloader
might have issues to reset/find the GPHYs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The DWR-921-C3 Wireless Routers with LTE embedded modem is based on the
MT7620N SoC.
Specification:
* MediaTek MT7620N (580 Mhz)
* 64 MB of RAM
* 16 MB of FLASH
* 802.11bgn radio
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* 2x external, detachable (LTE) antennas
* UART header on PCB (57600 8n1)
* 6x LED (GPIO-controlled)
* 1x bi-color Signal Strength LED (GPIO-controlled)
* 2x button
* JBOOT bootloader
Installation:
Apply factory image via d-link http web-gui.
How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
curl -F FN=@XXXXX.binhttp://192.168.123.254/upg
where XXXXX.bin is name of firmware file.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The DWR-921-C1 Wireless Routers with LTE embedded modem is based on the
MT7620N SoC.
Specification:
* MediaTek MT7620N (580 Mhz)
* 64 MB of RAM
* 16 MB of FLASH
* 802.11bgn radio
* 5x 10/100 Mbps Ethernet (1 WAN and 4 LAN)
* 2x external, detachable (LTE) antennas
* UART header on PCB (57600 8n1)
* 6x LED (GPIO-controlled)
* 1x bi-color Signal Strength LED (GPIO-controlled)
* 2x button
* JBOOT bootloader
The status led has been assigned to the dwr-921-c1:green:sigstrength (lte
signal strength) led. At the end of the boot it is switched off and is
available for lte operation. Work correctly also during sysupgrade
operation.
Installation:
Apply factory image via d-link http web-gui.
How to revert to OEM firmware:
1.) Push the reset button and turn on the power. Wait until LED start
blinking (~10sec.)
2.) Upload original factory image via JBOOT http (IP: 192.168.123.254)
3.) If http doesn't work, it can be done with curl command:
curl -F FN=@XXXXX.binhttp://192.168.123.254/upg
where XXXXX.bin is name of firmware file.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
Backport patch which adds suport for the BroadMobi BM806U 3G/4G modem,
which is used in D-Link DWR-921 C3.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Backport patch which adds suport for the Wistron NeWeb d18q1 LTE modem
which is used in D-Link DWR-921 C1.
Signed-off-by: Giuseppe Lippolis <giu.lippolis@gmail.com>
drivers/mmc/host/mtk-mmc/dbg.c:51:13: warning: 'cmd_buf' defined but not used [-Wunused-variable]
static char cmd_buf[256];
^~~~~~~
In addition, msdc_reg[] is completely unused, even in debug
mode.
Signed-off-by: André Draszik <git@andred.net>
