Rafał Miłecki
ecd9abc8c0
kernel: use upstream firmware patch for Broadcom's NVRAM
...
This replaces our 2 downstream patches.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-05-14 12:44:50 +02:00
Álvaro Fernández Rojas
e656bcbab0
kernel: add bcma/ssb fallback SPROM support
...
This adds generic kernel support for Broadcom Fallback SPROMs so that it can be
used in any target, even non Broadcom ones.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2023-04-23 12:18:35 +02:00
John Audia
f4989239cc
kernel: bump 5.15 to 5.15.107
...
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Signed-off-by: John Audia <therealgraysky@proton.me>
2023-04-19 00:55:58 +02:00
Rafał Miłecki
b4ae914037
kernel: backport NVMEM late fixes from v6.2
...
They were backported to stable kernels but we backport more stuff on our
own so we have to pick up few remaining.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-02-23 09:50:01 +01:00
John Audia
4e9365a654
kernel: bump 5.15 to 5.15.90
...
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod
Signed-off-by: John Audia <therealgraysky@proton.me>
2023-01-26 00:16:00 +01:00
Rafał Miłecki
8dfe69cdfc
kernel: update nvmem subsystem to the latest upstream
...
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2023-01-06 22:08:03 +01:00
Linus Walleij
1bef8d62d4
bcm53xx: Patch to support BCMA rev 11
...
A backported patch to the BCMA driver necessary to support the
DWL-8610AP and DIR-890L. Patch will be in upstream v6.2.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2022-12-15 15:08:08 +01:00
Christian Lamparter
f6c61571fb
bcm53xx: remove MR32's openwrt specific patch for LEDs
...
The patch managed to sneak into v5.15 whereas it was
properly deleted for v5.10.
Fixes: 8f6e2bb178
2022-12-12 09:06:17 +01:00
Rafał Miłecki
8cdafa149e
bcm53xx: update DTS files with the latest changes
...
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-11-10 09:51:25 +01:00
John Audia
1eebe72a80
kernel: bump 5.15 to 5.15.77
...
Manually rebased:
bcm27xx/patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
lantiq/patches-5.15/0028-NET-lantiq-various-etop-fixes.patch
All other patches automatically rebased
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <therealgraysky@proton.me>
2022-11-05 16:26:38 +01:00
John Audia
a34255b795
kernel: bump 5.15 to 5.15.75
...
Removed upstreamed:
bcm27xx/patches-5.15/950-0446-drm-vc4-Fix-timings-for-VEC-modes.patch[1]
Manually rebased:
patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch
bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch
bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
All other patches automatically rebased
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.75&id=2810061452f9b748b096ad023d318690ca519aa3
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-30 17:54:59 +01:00
John Audia
b0a94fc60d
kernel: bump 5.15 to 5.15.74
...
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-18 15:09:23 +02:00
Aleksey Nasibulin
3413409ef6
bcm53xx: linksys ea6500-v2: extend RAM to full 256MB
...
Linksys ea6500-v2 have 256MB of ram. Currently we only use 128MB.
Expand the definition to use all the available RAM.
Signed-off-by: Aleksey Nasibulin <alealexpro100@ya.ru>
[ wrap to 80 columns ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
2022-10-13 16:34:50 +02:00
John Audia
9110126620
kernel: bump 5.15 to 5.15.72
...
Removed upstreamed:
generic/pending-5.15/722-net-mt7531-only-do-PLL-once-after-the-reset.patch[1]
bcm53xx/patches-5.15/082-v6.0-clk-iproc-Do-not-rely-on-node-name-for-correct-PLL-s.patch[2]
All other patches automatically rebased
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200, mvebu/cortexa72
Run-tested: bcm2711/RPi4B, mt7622/RT3200, mvebu/cortexa72 (RB5009UG+S+IN)
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.72&id=5de02ab84aeca765da0e4d8e999af35325ac67c2
2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.72&id=ab5c5787ab5ecdc4a7ea20b4ef542579e1beb49d
Signed-off-by: John Audia <therealgraysky@proton.me>
2022-10-09 22:26:16 +02:00
Rafał Miłecki
77d9cce604
bcm53xx: backport clk driver fix for DT nodes names
...
It allows dropping downstream patch renaming DT nodes.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-09-29 05:51:25 +02:00
Rafał Miłecki
2f50c53f17
bcm53xx: update NVMEM driver for NVRAM
...
Include support for NVMEM cells.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-09-14 14:21:57 +02:00
John Audia
fbe2f7db86
kernel: bump 5.15 to 5.15.67
...
All patches automatically rebased
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <therealgraysky@proton.me>
2022-09-09 21:08:37 +01:00
Petr Štetiar
ca5c695a45
kernel: bump 5.15 to 5.15.62
...
Deleted following upstreamed patches:
bcm27xx: 950-0006-drm-vc4-hdmi-Fix-HPD-GPIO-detection.patch
bcm27xx: 950-0420-drm-vc4-Adopt-the-dma-configuration-from-the-HVS-or-.patch
bcm27xx: 950-0425-drm-vc4-A-present-but-empty-dmas-disables-audio.patch
bcm27xx: 950-0432-vc4-drm-Avoid-full-hdmi-audio-fifo-writes.patch
bcm27xx: 950-0433-vc4-drm-vc4_plane-Remove-subpixel-positioning-check.patch
bcm27xx: 950-0435-drm-vc4-Correct-pixel-order-for-DSI0.patch
bcm27xx: 950-0436-drm-vc4-Register-dsi0-as-the-correct-vc4-encoder-typ.patch
bcm27xx: 950-0437-drm-vc4-Fix-dsi0-interrupt-support.patch
bcm27xx: 950-0438-drm-vc4-Add-correct-stop-condition-to-vc4_dsi_encode.patch
bcm27xx: 950-0443-drm-vc4-Fix-timings-for-interlaced-modes.patch
bcm27xx: 950-0445-drm-vc4-Fix-margin-calculations-for-the-right-bottom.patch
bcm27xx: 950-0475-drm-vc4-Reset-HDMI-MISC_CONTROL-register.patch
bcm27xx: 950-0476-drm-vc4-Release-workaround-buffer-and-DMA-in-error-p.patch
bcm27xx: 950-0477-drm-vc4-Correct-DSI-divider-calculations.patch
bcm27xx: 950-0664-drm-vc4-dsi-Correct-max-divider-to-255-not-7.patch
bcm53xx: 072-next-ARM_dts_BCM53015-add-mr26.patch
mediatek: 920-linux-next-dts-mt7622-bpi-r64-fix-wps-button.patch
Manually rebased following patches:
bcm27xx: 950-0004-drm-vc4-hdmi-Remove-the-DDC-probing-for-status-detec.patch
bcm27xx: 950-0700-net-phy-lan87xx-Decrease-phy-polling-rate.patch
bcm27xx: 950-0711-drm-vc4-Rename-bridge-to-out_bridge.patch
bcm27xx: 950-0713-drm-vc4-Remove-splitting-the-bridge-chain-from-the-d.patch
bcm27xx: 950-0715-drm-vc4-Convert-vc4_dsi-to-using-a-bridge-instead-of.patch
bcm27xx: 950-0787-vc4-drm-vc4_plane-Keep-fractional-source-coords-insi.patch
bcm27xx: 950-0914-mmc-block-Don-t-do-single-sector-reads-during-recove.patch
Runtime tested on turris-omnia and glinet-b1300.
Tested-by: John Audia <therealgraysky@proton.me> [bcm2711/RPi4B, mt7622/RT3200]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
2022-08-23 10:37:04 +02:00
John Audia
4921ab0be4
kernel: bump 5.15 to 5.15.56
...
Manually rebased:
bcm27xx/patches-5.15/950-0470-sound-usb-add-device-quirks-for-A4Tech-FHD-1080p-web.patch
Remove upstreamed:
bcm27xx/patches-5.15/950-0060-tty-amba-pl011-Add-un-throttle-support.patch[1]
All other patches automatically rebased.
1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.56&id=2db3b95166f72e6481a79b82b1d6f94f4b18fcc1
Build system: x86_64
Build-tested: bcm2711/RPi4B, mt7622/RT3200
Run-tested: bcm2711/RPi4B, mt7622/RT3200
Signed-off-by: John Audia <therealgraysky@proton.me>
2022-07-31 18:55:22 +02:00
Christian Lamparter
e37ba80633
bcm53xx: add support for Meraki MR26
...
Meraki MR26 is an EOL wireless access point featuring a
PoE ethernet port and two dual-band 3x3 MIMO 802.11n
radios and 1x1 dual-band WIFI dedicated to scanning.
Thank you Amir for the unit and PSU.
Hardware info:
SOC : Broadcom BCM53015A1KFEBG (dual-core Cortex-A9 CPU at 800 MHz)
RAM : SK hynix Inc. H5TQ1G63EFR, 1 Gbit DDR3 SDRAM = 128 MiB
NAND : Spansion S34ML01G100TF100, 1 Gbit SLC NAND Flash = 128 MiB
ETH : 1 GBit Ethernet Port - PoE
WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn
WIFI1 : Broadcom BCM43431KMLG, BCM43431 802.11 abgn
WIFI3 : Broadcom BCM43428 abgn (1x1:1 - id: 43428)
BUTTON: one reset button
LEDS : RGB-LED
MISC : Atmel AT24C64 8KiB EEPROM (i2c - seems empty)
: Ti INA219 26V, 12-bit, i2c output current/voltage/power monitor
: TPS23754, High Power/High Efficiency PoE Interface+DC/DC Controller
SERIAL:
WARNING: The serial port needs a TTL/RS-232 3V3 level converter!
The Serial setting is 115200-8-N-1. The board has a populated
right angle 1x4 0.1" pinheader.
The pinout is: VCC (next to J3, has little white arrow), RX, TX, GND.
This flashing procedure for the MR26 was tested with firmware:
"22-143410M-gf25cbf5a-asa".
U-Boot 2012.10-00063-g83f9fe4 (Jun 04 2014 - 21:22:39)
A guide how to open up the device is available on the wiki:
<https://openwrt.org/toh/meraki/mr26 >
Notes:
- The WIFI do work to a degree. Limited to 802.11bg in the 2.4GHz band.
- the WIFI macs are made up.
0. Create a separate Ethernet LAN which can't have access to the internet.
Ideally use 192.168.1.2 for your PC. The new OpenWrt firmware will setup
the network via DHCP Discovery, so make sure your PC is running
a DHCP-Server (i.e.: dnsmasq)
'# dnsmasq -i eth# -F 192.168.1.5,192.168.1.50
Download the openwrt-meraki-mr26 initramfs file from openwrt.org and
rename it to something simple like mr26.bin. Then put it into the tftp's
server directory.
1. Disassemble the MR26 device by removing all screws (4 screws are located
under the 4 rubber feets!) and prying open the plastic covers without
breaking the plastic retention clips. Once inside, remove the plastic
back casing. Be careful, there some "hidden" retention clips on both
sides of the LAN port, you need a light to see those. Next, you want to
remove all the screws on the outer metal shielding to get to the PCB.
It's not necessary to remove the antennas!
2. Connect the serial cable to the serial header and Ethernet patch cable
to the device.
4. Before connecting the power, get ready flood the serial console program
with the magic: xyzzy . This is necessary in order to get into the
u-boot prompt. Once Ready: connect power cable.
5. If you don't get the "u-boot>" prompt within the first few seconds,
you have to disconnect and reconnect the power cable and try again.
6. In the u-boot prompt enter:
setenv ipaddr 192.168.1.4
setenv serverip 192.168.1.2
tftpboot ${meraki_loadaddr} mr26.bin; bootm
this will boot a in-ram-only OpenWrt image.
7. Once it booted use sysupgrade to permanently install OpenWrt.
To do this: Download the latest sysupgrade.bin file and move
it to the device. Then use sysupgrade *sysupgrade.bin to install it.
WARNING: DO NOT DELETE the "storage" ubi volume!
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-07-15 15:21:44 +02:00
Rui Salvaterra
b55efebb1f
kernel: bump 5.15 to 5.15.47
...
Deleted (upstreamed):
generic/backport-5.15/702-v5.19-32-net-ethernet-mtk_eth_soc-out-of-bounds-read-in-mtk_h.patch [01]
[01] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.47&id=b24ca1cf846273361d5bd73a35de95a486a54b6d
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[Removed 702-v5.19-32-net-ethernet-mtk_eth_soc-out-of-bounds-read-in-mtk_h.patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-06-27 00:57:16 +02:00
Rui Salvaterra
251a382c28
kernel: bump 5.15 to 5.15.46
...
Deleted (upstreamed):
generic/backport-5.15/400-mtdblock-warn-if-opened-on-NAND.patch [01]
generic/backport-5.15/420-v5.19-01-mtd-spinand-gigadevice-fix-Quad-IO-for-GD5F1GQ5UExxG.patch [02]
bcm27xx/patches-5.15/950-0029-Revert-mailbox-avoid-timer-start-from-callback.patch [03]
bcm27xx/patches-5.15/950-0417-bcm2711_thermal-Don-t-clamp-temperature-at-zero.patch [04]
bcm27xx/patches-5.15/950-0740-drm-vc4-hvs-Fix-frame-count-register-readout.patch [05]
bcm27xx/patches-5.15/950-0755-drm-vc4-hvs-Reset-muxes-at-probe-time.patch [06]
bcm27xx/patches-5.15/950-0759-drm-vc4-txp-Don-t-set-TXP_VSTART_AT_EOF.patch [07]
bcm27xx/patches-5.15/950-0760-drm-vc4-txp-Force-alpha-to-be-0xff-if-it-s-disabled.patch [08]
bcm53xx/patches-5.15/031-v5.17-0005-ARM-dts-BCM5301X-update-CRU-block-description.patch [09]
mediatek/patches-5.15/102-mt7629-enable-arch-timer.patch [10]
Manually rebased:
bcm27xx/patches-5.15/950-0741-drm-vc4-hvs-Use-pointer-to-HVS-in-HVS_READ-and-HVS_W.patch
[01] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=f41c9418c5898c01634675150696da290fb86796
[02] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=d5b66645305c6f3a1b2cf75cee4157b07f293309
[03] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=119f99209d8531359bcb935f252ec435f9d21b13
[04] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=c4e1280abead1552e1764684079a43e222ccd163
[05] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=08465a1889cb48ec64431e9db745b5be15399251
[06] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=0e26a6da02e63b75b629573d13966c36aa6264f0
[07] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=01c9020b2e7c85e394879f34851805179ac3d1d8
[08] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=d47f85cc0171a5d3c5bd8cbb8a98983ca3357cbd
[09] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=5151f24ac937ff7eb1f078257c66e3c0f0296010
[10] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.46&id=ffea838686b82fbb2801cdfad6ba5309d15c032d
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-06-27 00:57:16 +02:00
Rafał Miłecki
c6f16b63fa
bcm53xx: copy patch disabling GRO to kernel 5.15
...
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-06-24 09:09:27 +02:00
Rafał Miłecki
d19c37486b
bcm53xx: copy bgmac revert (performance fix) to 5.15
...
Ref: 230c9da963
2022-06-17 08:04:31 +02:00
Rui Salvaterra
be381a7ac7
kernel: bump 5.15 to 5.15.33
...
Deleted (upstreamed):
generic/backport-5.15/350-v5.18-MIPS-pgalloc-fix-memory-leak-caused-by-pgd_free.patch [1]
generic/backport-5.15/730-v5.16-hv-utils-add-PTP_1588_CLOCK-to-Kconfig-to-fix-build.patch [2]
generic/pending-5.15/850-0014-PCI-aardvark-Fix-reading-PCI_EXP_RTSTA_PME-bit-on-em.patch [3]
generic/pending-5.15/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch [4]
Manually rebased:
generic/pending-5.15/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch
ramips/patches-5.15/710-at803x.patch
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=d29cda15cab086d82d692de016f7249545d4b6b4
[2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=d5aad7d63b1b5c1f3c4b69e12c05e7c7d196fae8
[3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=ed750e22e44366e264bcdf7b1cf0713f08f7980a
[4] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.33&id=0fe94b84c43cfea867e1721606185e8686d7d32f
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[Refresh patches again]
[Remove generic/pending-5.15/850-0002-PCI-aardvark-Fix-reading-MSI-interrupt-number.patch]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2022-04-09 19:31:46 +02:00
Rafał Miłecki
9ac80a47ea
bcm53xx: prepare kernel 5.15 support
...
Tested on Luxul XWR-3150 (boot, NAND, PCIe, switch, Ethernet).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-03-30 23:22:46 +02:00
