This package downloads raw files
which have names that are not corresponding to
the name and version of the package
as it is defined in the Makefile.
Use the option DL_SUBDIR to set the DL_DIR
to be a subdirectory named with
PKG_NAME and PKG_RELEASE
to better organize the downloads.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This package downloads raw files
which have names that are not corresponding to
the name and version of the package
as it is defined in the Makefile.
Use the option DL_SUBDIR to set the DL_DIR
to be a subdirectory named with
PKG_NAME and PKG_VERSION
to better organize the downloads.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This package downloads raw files
which have names that are not corresponding to
the name and version of the package
as it is defined in the Makefile.
Use the option DL_SUBDIR to set the DL_DIR
to be a subdirectory named with
PKG_NAME and PKG_VERSION
to better organize the downloads.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This package downloads raw files
which have names that are not corresponding to
the name and version of the package
as it is defined in the Makefile.
Use the option DL_SUBDIR to set the DL_DIR
to be a subdirectory named with
PKG_NAME and PKG_SOURCE_DATE
to better organize the downloads.
Define PKG_VERSION here
using PKG_SOURCE_DATE.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
The currently used shell expansion doesn't seem to exist [0] and also
does not work. This surely was not intended, so lets allow default
naming to actually work.
[0]: https://pubs.opengroup.org/onlinepubs/9699919799/utilities/V3_chap02.html
Fixes: be09c5a3cd65 ("base-files: add board.d support for bridge device")
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
46f04f3808e8 devices: add MediaTek MT7986 WiSoC
b3e08c8b5a8f ops: make support for wireless extensions optional
1f695d9c7f82 nl80211: allow phy names that don't start with 'phy'
b7f9f06e1594 nl80211: fix phy/netdev index lookup
4a43b0d40ba5 nl80211: look up the phy name instead of assuming name == phy<idx>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Also include the station auth_type in the ubus and log message in order
to detect, if clients used FT or FILS to associate
Signed-off-by: Felix Fietkau <nbd@nbd.name>
All contents of staging_dir/image are included in Image Builder (IB) in
case some binary needs to be included in final image. But in case of
this package, all sources are stored there and those clutter the final
tarball of IB for no reason. Those sources are not used during image
creation and are just dead weight. To put it in perspective, the IB for
21.02.0 is 158 MiB, 22.03.0-rc6 is 366 MiB and snapshot is over 620 MiB!
To fix it, put them in package build directory, so they won't end up
included in IB tarball.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Reviewed-by: Andre Heider <a.heider@gmail.com>
b704dc72e tests: sigma_dut and updated ConfResult value for Configurator failures
89de431f2 DPP: Add config response status value to DPP-CONF-SENT
10104915a tests: sigma_dut and DPP PB session overlap
80d5e264c Enhance QCA vendor roam event to indicate MLO links after reassociation
662249306 Update copyright notices for the QCA vendor definitions
8adcdd659 tests: Temporary workaround for dpp_chirp_ap_5g
ddcd15c2d tests: Fix fuzzing/sae build
7fa67861a tests: Fix p2p_channel_avoid3
ee3567d65 tests: Add more time for scan/connection
1d08b238c nl80211: Allow more time for the initial scan with 6 GHz
ac9e6a2ab tests: Allow 6 GHz opclasses in MBO checks
faf9c04cb Remove a host of unnecessary OPENSSL_IS_BORINGSSL ifdefs
b9cd5a82f Always process pending QCA_NL80211_VENDOR_SUBCMD_KEY_MGMT_ROAM_AUTH data
ef4cd8e33 QoS: Use common classifier_mask for ipv4/ipv6
93be02592 Add fixed FDD mode to qca_btc_chain_mode QCA vendor attribute
e7cbfa1c1 tests: sigma_dut and DPP Enrollee unsupported curves
5565fbee2 DPP: Check Enrollee supported curves when building Config Response
ceae05cec tests: sigma_dut and DPP MUDURL setting for hostapd
4cfb484e9 DPP: Allow dpp_controller_start without arguments in CLIs
c97000933 Fix ifdef condition for imsi_privacy_cert
2a9a61d6c tests: SAE with extended key AKM
e35f6ed1d tests: More detailed report on SAE PMKSA caching error case
f70db167a SAE: Derive a variable length PMK with the new AKM suites
91010e6f6 SAE: Indicate AKM suite selector in commit for new AKM suites
e81ec0962 SAE: Use H2E unconditionally with the new AKM suites
f8eed2e8b SAE: Store PMK length and AKM in SAE data
9dc4e9d13 SAE: EAPOL-Key and key/MIC length information for the new AKM suites
a32ef3cfb SAE: Driver capability flags for the new SAE AKM suites
91df8c9c6 SAE: Internal WPA_KEY_MGMT_* defines for extended key AKMs
5c8a714b1 SAE: Use wpa_key_mgmt_sae() helper
5456b0f26 Define new RSN AKM suite selector values
def33101c DPP: Clear push button announcement state on wpa_supplicant FLUSH
35587fa8f tests: DPP Controller/Relay with need to discover Controller
d22dfe918 DPP: Event message for indicating when Relay would need a Controller
ca7892e98 tests: DPP Relay and adding/removing connection to a Controller
bfe3cfc38 DPP: Allow Relay connections to Controllers to be added and removed
808834b18 Add a comparison function for hostapd_ip_addr
f7763880b DPP: Advertise Configurator connectivity on Relay automatically
ff7cc1d49 tests: DPP Relay and dynamic Controller addition
ca682f80a DPP: Dynamic Controller initiated connection on Relay
d2388bcca DPP: Strict validation of PKEX peer bootstrapping key during auth
a7b8cef8b DPP3: Fix push button boostrapping key passing through PKEX
69d7c8e6b DPP: Add peer=id entry for PKEX-over-TCP case
b607d2723 tests: sigma_dut and DPP PB Configurator in wpa_supplicant
1ff9251a8 DPP3: Push button Configurator in wpa_supplicant
b94e46bc7 tests: PB Configurator in wpa_supplicant
ca4e82cbf tests: sigma_dut DPP/PKEX initiator as Configurator over TCP and Wi-Fi
e9137950f DPP: Recognize own PKEX Exchange Request if it ends up being received
692956446 DPP: Note PKEX code/identifier deletion in debug log
dfa9183b1 tests: DPP reconfig after Controller-initiated operation through Relay
ae4a3a6f6 DPP: Add DPP-CONF-REQ-RX event for Controller
17216b524 tests: sigma_dut DPP/PKEX initiator as Configurator (TCP) through Relay
fb2937b85 DPP: Allow Controller to initiate PKEX through Relay
15af83cf1 DPP: Delete PKEX code and identifier on success completion of PKEX
d86ed5b72 tests: Allow DPP_PKEX_REMOVE success in dpp_pkex_hostapd_errors
0a4f391b1 tests: sigma_dut and DPP Connector Privacy
479e412a6 DPP3: Default value for dpp_connector_privacy
7d12871ba test: DPP Private Peer Introduction protocol
148de3e0d DPP3: Private Peer Introduction protocol
786ea402b HPKE base mode with single-shot API
f0273bc81 OpenSSL: Remove a forgotten debug print
f2bb0839f test: DPP 3rd party config information
68209ddbe DPP: Allow 3rd party information to be added into config object
0e2217c95 DPP: Allow 3rd party information to be added into config request obj
3d82fbe05 Add QCA vendor subcommand and attributes for SCS rule configuration
16b62ddfa QCA vendor attribute for DBAM configuration
004b1ff47 tests: DPP Controller initiating through Relay
451ede2c3 DPP: Allow AP/Relay to be configured to listed for new TCP connections
248654d36 tests: sigma_dut DPP PB test cases
697b7d7ec tests: DPP push button
7bbe85987 DPP3: Allow external configuration to be specified on AP for PB
8db786a43 DPP3: Testing functionality for push button announcements
37bccfcab DPP3: Push button bootstrap mechanism
a0054fe7c Add AP and STA specific P802.11az security capabilities (vendor command)
159e63613 QCA vendor command for CoAP offload processing
3b7bb17f6 Add QCA vendor attribute for TIM beacon statistics
09a281e52 Add QCA vendor interface for PASN offload to userspace
809fb96fa Add a vendor attribute to configure concurrency policy for AP interface
a5754f531 Rename QCA_NL80211_VENDOR_SUBCMD_CONCURRENT_MULTI_STA_POLICY
085a3fc76 EHT: Add 320 channel width support
bafe35df0 Move CHANWIDTH_* definitions from ieee80211_defs.h to defs.h
92f549901 tests: Remove the 80+80 vs. 160 part from wpa2_ocv_ap_vht160_mismatch
c580c2aec tests: Make OCV negative test error cases more robust
3c2ba98ad Add QCA vendor event to indicate driver recovery after internal failures
6b461f68c Set current_ssid before changing state to ASSOCIATING
8dd826741 QCA vendor attribute to configure direct data path for audio traffic
504be2f9d QCA vendor command support to get WLAN radio combinations
d5905dbc8 OCV: Check the Frequency Segment 1 Channel Number only on 80+80 MHz
Signed-off-by: David Bauer <mail@david-bauer.net>
Don't select channels designated for exclusive-indoor use when the
country3 element is set on outdoor operation.
Signed-off-by: David Bauer <mail@david-bauer.net>
This matches the scheme used by other target packages and will avoid
confusion with any future version.
Signed-off-by: Andre Heider <a.heider@gmail.com>
The 'fxload' tool contained in the examples provided with libusb is
actually useful and turns out to be the only way to load firmware into
some rather ancient EZ-USB microcontrollers made by Cypress (formerly
Anchor Chips).
The original 'fxload' tool from hotplug-linux has been abandonned long
ago and requires usbfs to be mounted in /proc/bus/usb/ (like it was in
Linux 2.4...).
Hence the best option is to package the modern 'fxload' from the libusb
examples which (unsurprisingly) uses libusb and works on modern
systems.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
e065a7627a46 pex: update last query sent timestamp
6c888f897862 unet-cli: add stun server list editing support
Signed-off-by: Felix Fietkau <nbd@nbd.name>
21360a1b1ce6 cli: fix typo
abfebece0af1 wg-linux: ship a copy of linux/wireguard.h
1cbb1a543cb3 pex: reduce unnecessary ping traffic
0c2f39e52d5d pex: remove pex event debug spam
dcf1362c2104 pex: add support for sending/receiving global PEX messages via unix socket
df5f70b8858c ubus: notify on network updates
e58a56697131 add DHT discovery service
be175767bc67 pex: keep active pex hosts after the specified timeout
543e4a3d2ed7 pex: move rx header check to callback function
395659b9c415 pex: move raw ip send code to sendto_rawudp() in utils.c
dda15ea8b3b2 pex: add utility function to get the sockets based on type / address family
e88f2cd4d3f0 utils: add support for passings address family to network_get_endpoint()
639cdcdf6eda pex: add support for figuring out the external data port via STUN servers
9144339ebe1f pex: improve handling of a longer list of PEX hosts
38212218ecdd unet-cli: add DHT support
0d37ca75434d pex: automatically create host entries from incoming endpoint port notifications
035fcc56ef60 host: keep multiple endpoint candidates, one for each type
a089e8ae7504 pex: avoid sending a query to a host more than once every 15 seconds
Signed-off-by: Felix Fietkau <nbd@nbd.name>
libwolfssl-cpu-crypto is a variant of libwolfssl with support for
cryptographic CPU instructions on x86_64 and aarch64.
On aarch64, wolfSSL does not perform run-time detection, so the library
will crash when the AES functions are called. A preinst script attempts
to check for support by querying /proc/cpuinfo, if installed in a
running system. When building an image, the script will check the
DISTRIB_TARGET value in /etc/openwrt_release, and will abort
installation if target is bcm27xx.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
cc4eb79 ubus: support obtaining numeric error code
01c412c ubus: add toplevel constants for ubus status codes
8e240fa ubus: allow object method call handlers to return a numeric status code
5cdddd3 lib: add limit support to split() and replace()
0ba9c3e fs: add optional third permission argument to fs.open()
c1f7b3b lib: remove fixed capture group limit in match() and regex replace()
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Instead of always including the XHCI driver in the kernel on all
MediaTek boards, selectively include the kernel module only on boards
which actually make use of USB functionality.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
add Flow Queuing with Proportional Integral controller Enhanced (FQ-PIE) as an
optional kmod in network support and extract sched-pie from kmod-sched to
allow dependency on just kmod-sched-pie (PIE).
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
Add support for the TP-Link SG2210P switch. This is an RTL8380 based
switch with eight RJ-45 ports with 802.3af PoE, and two SFP ports.
This device shares the same board with the SG2008P and SG2008. To
model this, declare all the capabilities in the sg2xxx dtsi, and
disable unpopulated on the lower end models.
Specifications:
---------------
- SoC: Realtek RTL8380M
- Flash: 32 MiB SPI flash (Vendor varies)
- RAM: 256 MiB (Vendor varies)
- Ethernet: 8x 10/100/1000 Mbps with PoE (all ports)
2x SFP ports
- Buttons: 1x "Reset" button on front panel
- Power: 53.5V DC barrel jack
- UART: 1x serial header, unpopulated
- PoE: 2x TI TPS23861 I2C PoE controller
Works:
------
- (8) RJ-45 ethernet ports
- (2) SFP ports (with caveats)
- Switch functions
- System LED
Not yet enabled:
----------------
- Power-over-Ethernet (driver works, but doesn't enable "auto" mode)
- PoE LEDs
Enabling SFP ports:
-------------------
The SFP port control lines are hardwired, except for tx-disable. These
lines are controller by the RTL8231 in shift register mode. There is
no driver support for this yet.
However, to enable the lasers on SFP1 and SFP2 respectively:
echo 0x0510ff00 > /sys/kernel/debug/rtl838x/led/led_p_en_ctrl
echo 0x140 > /sys/kernel/debug/rtl838x/led/led_sw_p_ctrl.26
echo 0x140 > /sys/kernel/debug/rtl838x/led/led_sw_p_ctrl.24
Install via serial console/tftp:
--------------------------------
The footprints R27 (0201) and R28 (0402) are not populated. To enable
serial console, 50 ohm resistors should be soldered -- any value from
0 ohm to 50 ohm will work. R27 can be replaced by a solder bridge.
The u-boot firmware drops to a TP-Link specific "BOOTUTIL" shell at
38400 baud. There is no known way to exit out of this shell, and no
way to do anything useful.
Ideally, one would trick the bootloader into flashing the sysupgrade
image first. However, if the image exceeds 6MiB in size, it will not
work. The sysupgrade image can also be flashed. To install OpenWrt:
Prepare a tftp server with:
1. server address: 192.168.0.146
2. the image as: "uImage.img"
Power on device, and stop boot by pressing any key.
Once the shell is active:
1. Ground out the CLK (pin 16) of the ROM (U7)
2. Select option "3. Start"
3. Bootloader notes that "The kernel has been damaged!"
4. Release CLK as sson as bootloader thinks image is corrupted.
5. Bootloader enters automatic recovery -- details printed on console
6. Watch as the bootloader flashes and boots OpenWrt.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[OpenWrt capitalisation in commit message]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Serge Vasilugin reports:
To improve mt7620 built-in wifi performance some changes:
1. Correct BW20/BW40 switching (see comments with mark (1))
2. Correct TX_SW_CFG1 MAC reg from v3 of vendor driver see
https://gitlab.com/dm38/padavan-ng/-/blob/master/trunk/proprietary/rt_wifi/rtpci/3.0.X.X/mt76x2/chips/rt6352.c#L531
3. Set bbp66 for all chains.
4. US_CYC_CNT init based on Programming guide, default value was 33 (pci),
set chipset bus clock with fallback to cpu clock/3.
5. Don't overwrite default values for mt7620.
6. Correct some typos.
7. Add support for external LNA:
a) RF and BBP regs never be corrected for this mode
b) eLNA is driven the same way as ePA with mt7620's pin PA
but vendor driver explicitly pin PA to gpio mode (for forrect calibration?)
so I'm not sure that request for pa_pin in dts-file will be enough
First 5 changes (really 2) improve performance for boards w/o eLNA/ePA.
Changes 7 add support for eLNA
Configuration w/o eLAN/ePA and with eLNA show results
tx/rx (from router point of view) for each stream:
35-40/30-35 Mbps for HT20
65-70/60-65 Mbps for HT40
Yes. Max results for 2T2R client is 140-145/135-140
with peaks 160/150, It correspond to mediatek driver results.
Boards with ePA untested.
Reported-by: Serge Vasilugin <vasilugin@yandex.ru>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Prepare patches for sending upstream by adding patch descriptions
generated from the original OpenWrt commits adding each patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Hardware:
SoC: MediaTek MT7629 Cortex-A7 (ARMv7 1.25GHz, Dual-Core)
RAM: DDR3 128MB
Flash: Macronix MX35LF1GE4AB (SPI-NAND 128MB)
WiFi: MediaTek MT7761N (2.4GHz) / MediaTek MT7762N (5GHz) - no driver
Ethernet: SoC (WAN) / MediaTek MT7531 (LAN x4)
UART: [GND, RX, TX, 3.3V] (115200)
Installation:
- Flash recovery image with TFTP recovery
Revert to stock firmware:
- Flash stock firmware with TFTP recovery
TFTP Recovery method:
1. Unplug the router
2. Hold the reset button and plug in
3. Release when the power LED stops flashing and go off
4. Set your computer IP address manually to 192.168.0.x / 255.255.255.0
5. Flash image with TFTP client to 192.168.0.1
Signed-off-by: Yoonji Park <koreapyj@dcmys.kr>
xdp-tools build currently breaks on build hosts which do not have
libbpf headers installed because the build system wrongly tries to
use the host's include path.
Properly pass path to libbpf headers to xdp-tools build system to
fix build e.g. on the buildbots.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add support for TP-Link Deco S4 wifi router
The label refers to the device as S4R and the TP-Link firmware
site calls it the Deco S4 v2. (There does not appear to be a v1)
Hardware (and FCC id) are identical to the Deco M4R v2 but the
flash layout is ordered differently and the OEM firmware encrypts
some config parameters (including the label mac address) in flash
In order to set the encrypted mac address, the wlan's caldata
node is removed from the DTS so the mac can be decrypted with
the help of the uencrypt tool and patched into the wlan fw
via hotplug
Specifications:
SoC: QCA9563-AL3A
RAM: Zentel A3R1GE40JBF
Wireless 2.4GHz: QCA9563-AL3A (main SoC)
Wireless 5GHz: QCA9886
Ethernet Switch: QCA8337N-AL3C
Flash: 16 MB SPI NOR
UART serial access (115200N1) on board via solder pads:
RX = TP1 pad
TX = TP2 pad
GND = C201 (pad nearest board edge)
The device's bootloader and web gui will only accept images that
were signed using TP-Link's RSA key, however a memory safety bug
in the bootloader can be leveraged to install openwrt without
accessing the serial console. See developer forum S4 support page
for link to a "firmware" file that starts a tftp client, or you
may generate one on your own like this:
```
python - > deco_s4_faux_fw_tftp.bin <<EOF
import sys
from struct import pack
b = pack('>I', 0x00008000) + b'X'*16 + b"fw-type:" \
+ b'x'*256 + b"S000S001S002" + pack('>I', 0x80060200) \
b += b"\x00"*(0x200-len(b)) \
+ pack(">33I", *[0x3c0887fc, 0x35083ddc, 0xad000000, 0x24050000,
0x3c048006, 0x348402a0, 0x3c1987f9, 0x373947f4,
0x0320f809, 0x00000000, 0x24050000, 0x3c048006,
0x348402d0, 0x3c1987f9, 0x373947f4, 0x0320f809,
0x00000000, 0x24050000, 0x3c048006, 0x34840300,
0x3c1987f9, 0x373947f4, 0x0320f809, 0x00000000,
0x24050000, 0x3c048006, 0x34840400, 0x3c1987f9,
0x373947f4, 0x0320f809, 0x00000000, 0x1000fff1,
0x00000000])
b += b"\xff"*(0x2A0-len(b)) + b"setenv serverip 192.168.0.2\x00"
b += b"\xff"*(0x2D0-len(b)) + b"setenv ipaddr 192.168.0.1\x00"
b += b"\xff"*(0x300-len(b)) + b"tftpboot 0x81000000 initramfs-kernel.bin\x00"
b += b"\xff"*(0x400-len(b)) + b"bootm 0x81000000\x00"
b += b"\xff"*(0x8000-len(b))
sys.stdout.buffer.write(b)
EOF
```
Installation:
1. Run tftp server on pc with static ip 192.168.0.2
2. Place openwrt "initramfs-kernel.bin" image in tftp root dir
3. Connect pc to router ethernet port1
4. While holding in reset button on bottom of router, power on router
5. From pc access router webgui at http://192.168.0.1
6. Upload deco_s4_faux_fw_tftp.bin
7. Router will load and execture in-memory openwrt
8. Switch pc back to dhcp or static 192.168.1.x
9. Flash openwrt sysupgrade image via luci/ssh at 192.168.1.1
Revert to stock:
Press and hold reset button while powering device to start the
bootloader's recovery mode, where stock firmware can be uploaded
via web gui at 192.168.0.1
Please note that one additional non-github commits is also needed:
firmware-utils: add tplink-safeloader support for Deco S4
Signed-off-by: Nick French <nickfrench@gmail.com>
FCC ID: U2M-CAP2100AG
WatchGuard AP100 is an indoor wireless access point with
1 Gb ethernet port, dual-band but single-radio wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP300 v2
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- AR9344 SOC MIPS 74kc, 2.4 GHz AND 5 GHz WMAC, 2x2
- AR8035-A EPHY RGMII GbE with PoE+ IN
- 25 MHz clock
- 16 MB FLASH mx25l12805d
- 2x 64 MB RAM
- UART console J11, populated
- GPIO watchdog GPIO 16, 20 sec toggle
- 2 antennas 5 dBi, internal omni-directional plates
- 5 LEDs power, eth0 link/data, 2G, 5G
- 1 button reset
**MAC addresses:**
Label has no MAC
Only one Vendor MAC address in flash at art 0x0
eth0 ---- *:e5 art 0x0 -2
phy0 ---- *:e5 art 0x0 -2
**Installation:**
Method 1: OEM webpage
use OEM webpage for firmware upgrade to upload factory.bin
Method 2: root shell
It may be necessary to use a Watchguard router to flash the image to the AP
and / or to downgrade the software on the AP to access SSH
For some Watchguard devices, serial console over UART is disabled.
NOTE: DHCP is not enabled by default after flashing
**TFTP recovery:**
reset button has no function at boot time
only possible with modified uboot environment,
(see commit message for Watchguard AP300)
**Return to OEM:**
user should make backup of MTD partitions
and write the backups back to mtd devices
in order to revert to OEM reliably
It may be possible to use sysupgrade
with an OEM image as well...
(not tested)
**OEM upgrade info:**
The OEM upgrade script is at /etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
**Note on eth0 PLL-data:**
The default Ethernet Configuration register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For AR934x series, the PLL registers for eth0
can be see in the DTSI as 0x2c.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x1805002c 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
**Note on WatchGuard Magic string:**
The OEM upgrade script is a modified version of
the generic Senao sysupgrade script
which is used on EnGenius devices.
On WatchGuard boards produced by Senao,
images are verified using a md5sum checksum of
the upgrade image concatenated with a magic string.
this checksum is then appended to the end of the final image.
This variable does not apply to all the senao devices
so set to null string as default
Tested-by: Steve Wheeler <stephenw10@gmail.com>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: U2M-CAP4200AG
WatchGuard AP200 is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP600
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- AR9344 SOC MIPS 74kc, 2.4 GHz WMAC, 2x2
- AR9382 WLAN PCI card 168c:0030, 5 GHz, 2x2, 26dBm
- AR8035-A EPHY RGMII GbE with PoE+ IN
- 25 MHz clock
- 16 MB FLASH mx25l12805d
- 2x 64 MB RAM
- UART console J11, populated
- GPIO watchdog GPIO 16, 20 sec toggle
- 4 antennas 5 dBi, internal omni-directional plates
- 5 LEDs power, eth0 link/data, 2G, 5G
- 1 button reset
**MAC addresses:**
Label has no MAC
Only one Vendor MAC address in flash at art 0x0
eth0 ---- *:be art 0x0 -2
phy1 ---- *:bf art 0x0 -1
phy0 ---- *:be art 0x0 -2
**Installation:**
Method 1: OEM webpage
use OEM webpage for firmware upgrade to upload factory.bin
Method 2: root shell
It may be necessary to use a Watchguard router to flash the image to the AP
and / or to downgrade the software on the AP to access SSH
For some Watchguard devices, serial console over UART is disabled.
NOTE: DHCP is not enabled by default after flashing
**TFTP recovery:**
reset button has no function at boot time
only possible with modified uboot environment,
(see commit message for Watchguard AP300)
**Return to OEM:**
user should make backup of MTD partitions
and write the backups back to mtd devices
in order to revert to OEM reliably
It may be possible to use sysupgrade
with an OEM image as well...
(not tested)
**OEM upgrade info:**
The OEM upgrade script is at /etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
**Note on eth0 PLL-data:**
The default Ethernet Configuration register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For AR934x series, the PLL registers for eth0
can be see in the DTSI as 0x2c.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x1805002c 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
**Note on WatchGuard Magic string:**
The OEM upgrade script is a modified version of
the generic Senao sysupgrade script
which is used on EnGenius devices.
On WatchGuard boards produced by Senao,
images are verified using a md5sum checksum of
the upgrade image concatenated with a magic string.
this checksum is then appended to the end of the final image.
This variable does not apply to all the senao devices
so set to null string as default
Tested-by: Steve Wheeler <stephenw10@gmail.com>
Tested-by: John Delaney <johnd@ankco.net>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
FCC ID: Q6G-AP300
WatchGuard AP300 is an indoor wireless access point with
1 Gb ethernet port, dual-band wireless,
internal antenna plates, and 802.3at PoE+
this board is a Senao device:
the hardware is equivalent to EnGenius EAP1750
the software is modified Senao SDK which is based on openwrt and uboot
including image checksum verification at boot time,
and a failsafe image that boots if checksum fails
**Specification:**
- QCA9558 SOC MIPS 74kc, 2.4 GHz WMAC, 3x3
- QCA9880 WLAN PCI card 168c:003c, 5 GHz, 3x3, 26dBm
- AR8035-A PHY RGMII GbE with PoE+ IN
- 40 MHz clock
- 32 MB FLASH S25FL512S
- 2x 64 MB RAM NT5TU32M16
- UART console J10, populated
- GPIO watchdog GPIO 16, 20 sec toggle
- 6 antennas 5 dBi, internal omni-directional plates
- 5 LEDs power, eth0 link/data, 2G, 5G
- 1 button reset
**MAC addresses:**
MAC address labeled as ETH
Only one Vendor MAC address in flash at art 0x0
eth0 ETH *:3c art 0x0
phy1 ---- *:3d ---
phy0 ---- *:3e ---
**Serial console access:**
For this board, its not certain whether UART is possible
it is likely that software is blocking console access
the RX line on the board for UART is shorted to ground by resistor R176
the resistors R175 and R176 are next to the UART RX pin at J10
however console output is garbage even after this fix
**Installation:**
Method 1: OEM webpage
use OEM webpage for firmware upgrade to upload factory.bin
Method 2: root shell access
downgrade XTM firewall to v2.0.0.1
downgrade AP300 firmware: v1.0.1
remove / unpair AP from controller
perform factory reset with reset button
connect ethernet to a computer
login to OEM webpage with default address / pass: wgwap
enable SSHD in OEM webpage settings
access root shell with SSH as user 'root'
modify uboot environment to automatically try TFTP at boot time
(see command below)
rename initramfs-kernel.bin to test.bin
load test.bin over TFTP (see TFTP recovery)
(optionally backup all mtdblocks to have flash backup)
perform a sysupgrade with sysupgrade.bin
NOTE: DHCP is not enabled by default after flashing
**TFTP recovery:**
server ip: 192.168.1.101
reset button seems to do nothing at boot time...
only possible with modified uboot environment,
running this command in the root shell:
fw_setenv bootcmd 'if ping 192.168.1.101; then tftp 0x82000000 test.bin && bootm 0x82000000; else bootm 0x9f0a0000; fi'
and verify that it is correct with
fw_printenv
then, before boot, the device will attempt TFTP from 192.168.1.101
looking for file 'test.bin'
to return uboot environment to normal:
fw_setenv bootcmd 'bootm 0x9f0a0000'
**Return to OEM:**
user should make backup of MTD partitions
and write the backups back to mtd devices
in order to revert to OEM
(see installation method 2)
It may be possible to use sysupgrade
with an OEM image as well...
(not tested)
**OEM upgrade info:**
The OEM upgrade script is at /etc/fwupgrade.sh
OKLI kernel loader is required because the OEM software
expects the kernel to be no greater than 1536k
and the factory.bin upgrade procedure would otherwise
overwrite part of the kernel when writing rootfs.
**Note on eth0 PLL-data:**
The default Ethernet Configuration register values will not work
because of the external AR8035 switch between
the SOC and the ethernet port.
For QCA955x series, the PLL registers for eth0 and eth1
can be see in the DTSI as 0x28 and 0x48 respectively.
Therefore the PLL registers can be read from uboot
for each link speed after attempting tftpboot
or another network action using that link speed
with `md 0x18050028 1` and `md 0x18050048 1`.
The clock delay required for RGMII can be applied
at the PHY side, using the at803x driver `phy-mode`.
Therefore the PLL registers for GMAC0
do not need the bits for delay on the MAC side.
This is possible due to fixes in at803x driver
since Linux 5.1 and 5.3
**Note on WatchGuard Magic string:**
The OEM upgrade script is a modified version of
the generic Senao sysupgrade script
which is used on EnGenius devices.
On WatchGuard boards produced by Senao,
images are verified using a md5sum checksum of
the upgrade image concatenated with a magic string.
this checksum is then appended to the end of the final image.
This variable does not apply to all the senao devices
so set to null string as default
Tested-by: Alessandro Kornowski <ak@wski.org>
Tested-by: John Wagner <john@wagner.us.org>
Signed-off-by: Michael Pratt <mcpratt@pm.me>