Fix ART offset (make it universal for 8/16 MB versions of the board) and
while at it, include also GPIO setup for h/w watchdog (EM6324QYSP5B).
Fixes: FS#1532
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Fixes "unregister_netdevice: waiting for lo to become free. Usage count = 1"
messages which started appearing since the update to 4.4.103. That
problem was exposed by upstream commit 76da0704507bb ("ipv6: only call
ip6_route_dev_notify() once for NETDEV_UNREGISTER") backported to 4.4.x
branch in 2417da3f4d6bc.
Fixes: 2b664499cd ("kernel: bump 4.4 to 4.4.103 for 17.01")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 58f7b5b96c)
Some Ubiquiti U-boot versions, in particular the "U-Boot 1.1.4.2-s956
(Jun 10 2015 - 10:54:50)" found with AirOS 5.6, do not correctly flush the
caches for the whole kernel address range after decompressing the kernel
image, leading to hard to debug boot failures, depending on kernel version
and configuration.
As a workaround, prepend the relocate-kernels loader, which will invalidate
the caches after moving the kernel to the correct load address.
Reported-by: Andreas Ziegler <dev@andreas-ziegler.de>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
This is important fix for flash parsing in some corner cases. In case
of TRX subpartition with rootfs being aligned to the flash block size it
was incorrectly registered twice. Detecting & registering it as a
standalone partition was resulting in an incorrect "firmware" partition
size and possibly broken sysupgrade.
It wasn't noticed before because "rootfs" alignment depends on a kernel
size. It can happen though - depending on the configuration and the
kernel size.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit f5195e72c0)
Previously, tplink_pharos_check_image() would accept any image with ELF
magic and only non-printable data in the support-list, as in this case the
while-read loop would not run at all. Add the new support-list offset and
ensure an image is only accepted when the model string is actually found.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Switching from kernel 4.4.120 to 4.4.124 introduced a regression in
the genirq code. It was caused by a commit 9d0273bb1c4b6 ("genirq: Use
irqd_get_trigger_type to compare the trigger type for shared IRQs").
On bcm53xx it breaks serial console and results in a flood of:
[ 22.078829] genirq: Flags mismatch irq 18. 00000080 (serial) vs. 00000080 (gpio)
[ 22.086432] genirq: Flags mismatch irq 18. 00000080 (serial) vs. 00000080 (gpio)
[ 22.601150] genirq: Flags mismatch irq 18. 00000080 (serial) vs. 00000080 (gpio)
[ 22.608845] genirq: Flags mismatch irq 18. 00000080 (serial) vs. 00000080 (gpio)
Later in the upstream "linux-4.4.y" branch that commit was reverted and
it was followed by a 4.4.126 release. Until we switch from 4.4.124 to
4.4.126 (or newer), let's backport that reverting commit.
Fixes: bed0ee7cbf ("Kernel: bump 4.4 to 4.4.124 for 17.01")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
At least on some devices, LEDs don't work anymore since kernel 4.4.120.
Revert the broken change.
See also: https://www.spinics.net/lists/stable/msg223656.html
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fixes issue FS#1355.
LPAE extensions are enabled, but the A13 does not support them.
The result is the boot process stopping at "Starting kernel ..."
Fixes: 468735c3a2 ("target: sunxi: enable kvm support")
Signed-off-by: Matteo Scordino <matteo.scordino@gmail.com>
Looking for a wrong LED file name was stopping this code from find any
LED. This affects devices with only a red/amber power LED.
Fixes: 3aaee1ba02 ("bcm53xx: failsafe support")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This bumps the 4.4. kernel in LEDE 17.01 to 4.4.116.
More Meltdown & Spectre mitigation.
* Refresh patches.
* Refresh x86/config for RETPOLINE.
* Deleted 8049-PCI-layerscape-Add-fsl-ls2085a-pcie-compatible-ID.patch (accepted upstream)
* Deleted 8050-PCI-layerscape-Fix-MSG-TLP-drop-setting.patch (accepted upstream)
* 650-pppoe_header_pad.patch does not apply anymore (code was replaced).
Bumps from 4.4.113 to 4.4.115 were handled by Kevin Darbyshire-Bryant.
Compile-tested on: ar71xx, ramips/mt7621, x86/64
Run-tested on: ar71xx, ramips/mt7621, x86/64
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Backport support for raw-ip mode including all known fixes afterwards.
Newer LTE modems only tend to support this mode, which was only
introduced in kernel 4.5.
Also backport support for the Quectel EC2x LTE modem series which is
a very popular device.
No custom changes were needed in order to apply these patches.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
dc7a1e8555 ("ramips: fix reporting effective VLAN ID on MT7621 switches")
341b1427fc ("ramips: properly map pvid for vlans with remapped vid on mt7530/762x switches")
bb4002c79d ("ramips: don't clobber vlans with remapped vid on mt7530/762x switches")
Fixes FS#991, FS#1147, FS#1341
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
The Netgear WNR2000v4 does not have a USB port. Hence, including USB packages into the default images is useless.
It looks like the WNR2000v4 definition in master is OK.
v2 fixes the silly typo in the patch title (WNR2000v4 instead of WNR200v4)
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
There are 3 ethernet ports on Y1. LAN1 on port1, LAN2 on port0 and WAN on
port4.
Use a standalone switch configuration to match this and use the switch
trigger so that LAN LED could indicate the connetction status for both
lan ports correctly.
This patch also drop the internet led configuration, because there is a
WAN led for port4 and eth0.2 isn't always used as WAN.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Kernel 4.4.109 added pp->link, pp->duplex and pp->speed setters to
mvneta_port_disable() which the mvneta patchset failed to patch out after
rebasing, leading to the following build error:
CC drivers/net/ethernet/marvell/mvneta.o
drivers/net/ethernet/marvell/mvneta.c: In function 'mvneta_port_disable':
drivers/net/ethernet/marvell/mvneta.c:1199:4: error: 'struct mvneta_port' has no member named 'link'
pp->link = 0;
^
drivers/net/ethernet/marvell/mvneta.c:1200:4: error: 'struct mvneta_port' has no member named 'duplex'
pp->duplex = -1;
^
drivers/net/ethernet/marvell/mvneta.c:1201:4: error: 'struct mvneta_port' has no member named 'speed'
pp->speed = 0;
^
Fix the issue by rebasing 134-net-mvneta-convert-to-phylink.patch to remove
these struct member accesses as well.
Fixes: 7f5a040359 ("kernel: update kernel 4.4 to version 4.4.110")
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
By default we are reusing the stack provided by CFE, like it is intended
by CFE. On my WRT54GS it is located at 0x8043BF30, so a big kernel image
could overwrite it. Relocate it to a different memory region which is
still under the 8MB RAM, but in the higher area. We only need this
memory region for the stack of the loader, Linux will set up this
for its own.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The boot process on a WRT54GL works the following way:
1. CFE gets loaded by the boot rom from flash
2. CFE loads the loader from the flash and gzip uncompresses it
3. CFE starts the loader
4. The loader stores the FW arguments and relocates itself to
BZ_TEXT_START (now 0x80600000)
5. The loader reads the Linux image from flash
6. The loader lzma decompresses the Linux image to LOADADDR (0x80001000)
7. The loader executes the uncompress Linux image at LOADADDR
The BZ_TEXT_START was set to 0x80400000 before. When the kernel gets
uncompressed and is bigger than BZ_TEXT_START - LOADADDR it overwrote
the loader which was currently uncompressing it and made the board
crash. Increase the BZ_TEXT_START my 2 MB to have more space for the
kernel. Even on 16MB RAM devices the memory goes till 0x80FFFFFF so this
should not be a problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It's a device based on BCM5365P (0x5365 package 0x00). This SoC has
USB 1.1 controller but device has two USB 2.0 parts. They are handled by
PCI-based controllers: 1106:3038 UHCI and 1106:3104 EHCI.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Bump 4.4 to 4.4.107 and refreshed all patches.
Made the following patch for Mediatek and Oxnas compatible with kernel 4.4.107:
0072-mtd-backport-v4.7-0day-patches-from-Boris.patch
Compile-tested: ar71xx
Run-tested: ar71xx
Signed-off-by: Etienne Haarsma <bladeoner112@gmail.com>
Reviewed-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Tested-by: Rosen Penev <rosenp@gmail.com>
The generic preinit code is now able to setup network and switch vlan settings
from the /etc/board.json file, therefor drop the target specific code.
Fixes FS#790.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 833c500cb2)
This patch fixes the switch port numbering on Mikrotik RB750r2 (hEX lite) and RB750UPr2 (hEX PoE lite).
Tested on a RB750UPr2. Maybe this patch is applicable to other devices (e.g. RB951Ui-2nD, RB952Ui-5ac2nD) but I have no way to test them.
Signed-off-by: João Chaínho <joaochainho@gmail.com>
(cherry picked from commit 61027e3430)
No longer rewrite opkg list output in package_list function, remove
the awk call in the pipe (which was intended for a single specific
use-case).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit d80d1b6c42)
commit 19ac879954 (imagebuilder: add package_list function) introduced
a new function 'package_list' to the imagebuilder Makefile.
Unfortunately the package list was poluted by stdout noise of the
Makefile itself as well as opkg. Redirect those outputs to stderr to
make sure that the package_list returned doesn't contain progress
info output but really only packages.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 1b555e1d2b)
The imagebuilder can now list all available packages by using make
package_list. This is usefull for scripts to retrieve a list of all
packages with versions (and size)
Signed-off-by: Paul Spooren <paul@spooren.de>
[daniel@makrotopia.org: fixed commit message]
(cherry picked from commit 19ac879954)
It is used by pretty much every target
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(backported from commit b47fd76563)
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
