The most recent patch added add lines in one block instead of in the
appropriate places to keep Makefiles in consistent style. Fix that.
Fixes: ff02e1561f ("pcre: add host variant of libpcre")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This ports the TP-Link TL-WPA8630 v1 from ar71xx to ath79.
Specifications:
SoC: QCA9563
CPU: 750 MHz
Flash/RAM: 8 / 128 MiB
Ethernet: 3x 1G ports (QCA8337 switch)
WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac (ath10k)
Buttons, LEDs and network setup appear to be almost identical
to the v2 revision.
Powerline interface is connected to switch port 5 (Label LAN4).
Installation:
No "fresh" device was available for testing the factory image.
It is not known whether flashing via OEM firmware GUI is possible
or not. A discussion from 2018 [1] about that indicates a few
adjustments are necessary, but it is not clear whether those
are already implemented with the TPLINK_HEADER_VERSION = 2 or not.
Note that for the TL-WPA8630P v1, the TPLINK_HWID needs to be
changed to 0x86310001 to allow factory flashing.
[1] https://forum.openwrt.org/t/solved-tl-wpa8630p-lede-does-not-install/8161/27
Recovery:
Recovery is only possible via serial.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
34aed01ca865 mt76: mt7915: use ieee80211_free_txskb to free tx skbs
efc8669db5f9 mt76: mt7915: fix max_mpdu_size field for A-MSDU
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Dependencies are meant to express actual run-time dependencies and
strictly speaking, libselinux can be build and used on kernels without
SELinux (not in a very meaningful way, but never mind).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The commands to read ath9k caldata on mikrotik subtarget are
mostly repetitive, so let's put them into a function to make
writing and reading them easier.
This function will only be required when patching the MAC address.
For cases where it is put correctly into the calibration data by
the vendor, caldata_sysfsload_from_file can be used directly as
done for ath10k at the moment.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for the MikroTik RouterBOARD 760iGS router.
It is similar to the already supported RouterBOARD 750Gr3.
The 760iGS device features an added SFP cage, and passive
PoE out on port 5 compared to the RB750Gr3.
https://mikrotik.com/product/hex_s
Specifications:
- SoC: MediaTek MT7621A
- CPU: 880MHz
- Flash: 16 MB
- RAM: 256 MB
- Ethernet: 5x 10/100/1000 Mbps
- SFP cage
- USB port
- microSD slot
Unsupported:
- Beeper (requires PWM driver)
- ZT2046Q (ADS7846 compatible) on SPI as slave 1 (CS1)
The linux driver requires an interrupt, and pendown GPIO
These are unknown, and not needed with the touchscreen
only used for temperature and voltage monitoring.
ads7846 hwmon:
temp0 is degrees Celsius
temp1 is voltage * 32
GPIOs:
- 07: input passive PoE out (lan5) compatible (Mikrotik) device connected
- 17: output passive PoE out (lan5) switch
Installation through RouterBoot follows the usual MikroTik method
https://openwrt.org/toh/mikrotik/common
To boot to intramfs image in RAM:
1. Setup TFTP server to serve intramfs image.
2. Plug Ethernet cable into WAN port.
3. Unplug power, hold reset button and plug power in.
Wait (~25 seconds) for beep and then release reset button.
The SFP LED will be lit in RouterBoot, but will not be lit in OpenWRT.
4. Wait for a minute. Router should be running OpenWrt,
check by plugging in to port 2-5 and going to 192.168.1.1.
To install OpenWrt to flash:
1. Follow steps above to boot intramfs image in RAM.
2. Flash the sysupgrade.bin image with web interface or sysupgrade.
3. Once the router reboots you will be running OpenWrt from flash.
OEM firmware differences:
- RouterOS assigns a different MAC address for each port
- The first address (E01 on the sticker) is used for wan (ether1 in OEM).
- The next address is used for lan2.
- The last address (E06 on the sticker) is used for sfp.
[Initial port work, shared dtsi]
Signed-off-by: Vince Grassia <vincenzo.grassia@zionark.com>
[SFP support and GPIO identification]
Signed-off-by: Luka Logar <luka.logar@iname.com>
[Misc. fixes and submission]
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[rebase, drop uart3 from state_default on 750gr3, minor commit
title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This moves some common definitions for Mikrotik devices, mainly
routerboot partitions and reset key, to a common DTSI file.
While at it, remove unused hard_config DT label.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds a `selinux` variant to `procd` allowing to load an
SELinux policy at boot.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This beeper hardware requires a PWM driver for frequency selection.
Since the GPIO driver does not provide that, revert the beeper
support to a simple gpio-export.
This effectively reverts the corresponding changes from
6ba58b7b02 ("ramips: cleanup the RB750Gr3 support")
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
[commit title/message facelift]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This driver is only used by ipq806x SoCs. Move it there and drop
dependency from ipq40xx since it's not used anywere.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[rebase on changes to previous patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
- Replace nvmem qcom patch with upstream version
- Update compatible
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[refresh patches, minor commit message rewording]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
- Replace dwc3 phy patch with upstream version
- Rework the dts to use the upstream bindings
- Update changed config flags
- Rename module to reflect config name
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[fix qcom,tx-deamp_3_5db typo, refresh patches, rename kmod]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: Paul Blazejowski <paulb@blazebox.homeip.net> [R7800]
The ssh symlink was still being created even when dbclient was disabled in the
build configuration. Fix this annoyance.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
The missing "size" property was acceptable in the context of a single
DTS as the underlying device is known to have a 64KB flash, and thus
the bios partition fit exactly between the preceding and following ones.
However as this block has moved in a DTSI, for the sake of clarity and
explicitness the size property is added to ensure that if the flash
happens to be larger than expected, the bios partition remains properly
sized.
Suggested-by: Thibaut VARÈNE <hacks@slashdirt.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This harmonizes the appearance of ethX nodes in qca953x DTSes by:
- having the same order of nodes and properties
- removing redundant status property on eth1 (set in qca953x.dtsi)
This is meant to help both copy-pasters and reviewers, since
deviations and errors can be spotted easier.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
After those symbols have been removed from generic kernel config,
they were added to the target config during every kernel config
refresh. As that's not desirable, add them back to the generic
config.
Fixes: d1a8217d87 ("kernel: clean-up build-configurable kernel config symbols")
Fixes: cfe235c436 ("kernel: modules: add package kmod-iosched-bfq")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The README file is displayed on "make help", but updating the
command has been overlooked during the README -> README.md
rename.
Fix it.
Fixes: d0113711a3 ("README: port to 21st century")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MikroTik SXT Lite5 (product code RBSXT5nDr2, also SXT 5nD r2) is
an outdoor 5GHz CPE with a 16 dBi integrated antenna built around the
Atheros AR9344 SoC. It is based on the "sxt5n" board platform.
Specifications:
- SoC: Atheros AR9344
- RAM: 64 MB
- Storage: 128 MB NAND
- Wireless: Atheros AR9340 (SoC) 802.11a/n 2x2:2
- Ethernet: Atheros AR8229 switch (SoC), 1x 10/100 port,
8-32 Vdc PoE in
- 6 user-controllable LEDs:
· 1x power (blue)
· 1x wlan (green)
· 4x rssi (green)
- 1 GPIO-controlled buzzer
See https://mikrotik.com/product/RBSXT5nDr2 for more details.
Notes:
The device was already supported in the ar71xx target. There, the
Ethernet port was handled by GMAC1. Here in ath79 it is handled by
GMAC0, which allows to get link information (loss, speed, duplex) on
the eth0 interface.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Acknowledgments:
Michael Pratt (@mpratt14) for helping on the network settings.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[rebase, use mikrotik LED label prefix, make names consistent,
add reg for bootloader2, use led_user for boot indication etc.,
minor cosmetic changes]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MikroTik RouterBOARD 921GS-5HPacD-15s (mANTBox 15s) is an outdoor
antenna for 5 GHz with an built-in router. This ports the board from
ar71xx.
See https://mikrotik.com/product/RB921GS-5HPacD-15S for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9558 (720 MHz)
- RAM: 128 MB
- Storage: 128 MB NAND
- Wireless: external QCA9892 802.11a/ac 2x2:2
- Ethernet: 1x 1000/100/10 Mbps, integrated, via AR8031 PHY, passive PoE in
- SFP: 1x host
Working:
- NAND storage detection
- Ethernet
- Wireless
- 1x user LED (blinks during boot, sysupgrade)
- Reset button
- Sysupgrade
Untested:
- SFP cage (probably not working)
Installation (untested):
- Boot initramfs image via TFTP and then flash sysupgrade image
As the embedded RB921-pcb is a stripped down version of the RB922 this patch
adds a common dtsi for this series and includes this to the final dts-files.
Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
[move ath10k-leds closer to ath10k definition in DTS files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The MikroTik RouterBOARD LHG 2nD (sold as LHG 2) is a 2.4 GHz
802.11b/g/n outdoor device with a feed and an integrated dual
polarization grid dish antenna based on the LHG-HB platform.
See https://mikrotik.com/product/lhg_2 for more info.
Specifications:
- SoC: Qualcomm Atheros QCA9533
- RAM: 64 MB
- Storage: 16 MB NOR
- Wireless: Atheros AR9531 (SoC) 802.11b/g/n 2x2:2, 18 dBi antenna
- Ethernet: Atheros AR8229 (SoC), 1x 10/100 port, 12-28 Vdc PoE in
- 8 user-controllable LEDs:
· 1x power (blue)
· 1x user (green)
· 1x lan (green)
· 1x wlan (green)
· 4x rssi (green)
Note:
The rssihigh LED is disabled, as it shares GPIO 16 with the reset
button.
Flashing:
TFTP boot initramfs image and then perform sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
[rebase, remove rssiled setup, adjust commit message, add DTSIs]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
8d9a62e4def7 mt76: mt7915: fix crash on tx rate report for invalid stations
825343467df4 mt76: fix double DMA unmap of the first buffer on 7615/7915
99804560372b mt76: mt7615: register ext_phy if DBDC is detected
93407be934b2 mt76: mt7615: move drv_own/fw_own in mt7615_mcu_ops
e7774de844e8 mt76: mt7663s: move drv_own/fw_own in mt7615_mcu_ops
a5602514ab03 mt76: mt7615: hold mt76 lock queueing wd in mt7615_queue_key_update
5c42061ce181 mt76: do not inject packets if MT76_STATE_PM is set
ae4757a0ae90 mt76: mt7615: reschedule runtime-pm receiving a tx interrupt
c4544d1e8a1a mt76: mt76s: fix oom in mt76s_tx_queue_skb_raw
dc73103874cc mt76: mt76s: move tx processing in a dedicated wq
c828c84cb134 mt76: mt7663s: move rx processing in txrx wq
2b34f2f6b0ef mt76: mt76s: move status processing in txrx wq
f957b050d848 mt76: mt76s: move tx/rx processing in 2 separate works
6fe964295bd9 mt76: mt76s: get rid of unused variable
43d6127d8851 mt76: mt7915: enable U-APSD on AP side
58774b605f1c mt76: set interrupt mask register to 0 before requesting irq
06f722d8046c mt76: mt7915: clean up and fix interrupt masking in the irq handler
2fbd6baac103 mt76: mt7615: only clear unmasked interrupts in irq tasklet
5ea8b6187da2 mt76: mt76x02: clean up and fix interrupt masking in the irq handler
f2e71f0c1b7e mt76: mt7615: do not do any work in napi poll after calling napi_complete_done()
1eb94624bb12 mt76: mt7915: do not do any work in napi poll after calling napi_complete_done()
5e0c587b9ac1 mt76: mt7915: clean up station stats polling and rate control update
9ab20dfbf7b1 mt76: mt7915: increase tx retry count
fa69dd96f9c0 mt76: mt7915: enable offloading of sequence number assignment
9816f9812adb mt76: move mt76_check_agg_ssn to driver tx_prepare calls
ad90170b0af9 mt76: mt7615: remove mtxq->agg_ssn assignment
335cd51be4c6 mt76: mt7915: simplify aggregation session check
21f7734cbb49 mt76: mt7915: add missing flags in WMM parameter settings
21182f90d947 mt76: mt7915: add Tx A-MSDU offloading support
27670514328f mt76: mt7615: use v1 MCU API on MT7615 to fix issues with adding/removing stations
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Not a large change from last time, but should fix at least one rare wave-2
crash. The htt-mgt-community builds are trimmed for supporting lots of
stations (typically 150+ stations per radio).
Tested on Netgear R7800.
Signed-off-by: Michael Yartys <michael.yartys@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Bump PKG_RELEASE for the affected packages as replacing "which" by
"command -v" represents a content change.
Fixes: 1fdf6b745c ("treewide: replace `which` with `command -v`")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Fix shellcheck SC2230
> which is non-standard. Use builtin 'command -v' instead.
Using `command -v` is POSIX compliant while `which` is not. Also to
mention, `command -v` is a shell builtin whereas `which` is a separate
busybox applet.
Once applied to everything concerning OpenWrt we can disable the busybox
feature `which` and save 3.8kB.
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Paul Spooren <mail@aparcar.org>
[also replace cases in zram-swap]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This problem has been fixed in upstream commit
6b6a3d9339f1c08efaa18a7fb7357e20b48bdc95. This patch now (harmlessly)
adds the same definition a second time.
Signed-off-by: Magnus Kroken <mkroken@gmail.com>
[bump PKG_RELEASE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Most targets have been updated to consistently use the vendor_model
scheme for device definitions and thus, image names.
Apply this to bcm47xx as well. This does _not_ apply any other
specific naming changes.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Most targets have been updated to consistently use the vendor_model
scheme for device definitions and thus, image names.
Apply this to bcm53xx as well. This does _not_ apply any other
specific naming changes.
Cc: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Now that my patches have been merged into upstream U-Boot, resync the
cosmetic changes and the commit IDs from the final commits.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The pkgconfig file references the host directories, not the openwrt
ones. Used SED to fix as is done elsewhere. Removed CMAKE_INSTALL as a
result.
Removed now pointless CFLAGS.
Added PKG_BUILD_PARALLEL for faster compilation.
Various rearrangements for consistency between packages.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
677aa53 Fix -W option for pppoe-discovery utility (#157)
115c419 Accept Malformed Windows Success Message (#156)
5bdb148 pppd: Add documentation of stop-bits option to pppd man page (#154)
2a7981f Add ipv6cp-accept-remote option
0678d3b pppd: Fix the default value for ipv6cp-accept-local to false
Refresh patches
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This fixes the following build problem with cake:
net/sched/act_ctinfo.c: In function 'tcf_ctinfo_act':
net/sched/act_ctinfo.c:99:6: error: implicit declaration of function 'tc_skb_protocol'; did you mean 'skb_protocol'? [-Werror=implicit-function-declaration]
if (tc_skb_protocol(skb) == htons(ETH_P_IP)) {
^~~~~~~~~~~~~~~
skb_protocol
CC [M] net/sched/sch_hfsc.o
Fixes: fdac05b741 ("kernel: Update kernel 4.19 to version 4.19.138")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In commit 87b35c16ad ("kernel: ubifs: create use file system format 4
by default") we changed the default UBIFS version used when the kernel
creates a new volume from 5 to 4. UBIFS v5 was added in kernel 4.10 and
only kernel 4.10 and later can read it.
We changed the kernel to create version 4 volumes also on more recent
kernel versions to make it possible to downgrade to an OpenWrt version
with kernel 4.9, the upgrade still works. This is probably not needed
any more and we can remove this patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
