We so far had two variables IMG_PREFIX and IMAGE_PREFIX with
different content. Since these names are obviously quite
confusing, this patch renames the latter to DEVICE_IMG_PREFIX,
as it's a device-dependent variable, while IMG_PREFIX is only
(sub)target-dependent.
For consistency, also rename IMAGE_NAME to DEVICE_IMG_NAME, as
that's a device-dependent variable as well.
Cc: Paul Spooren <mail@aparcar.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
MediaTek targets always use U-Boot's modern uImage.FIT format which
allows bundling several blobs into a single file including hashes,
descriptions and more. In fact, we are already using that to bundle
the Flattened Device Tree blob with the kernel on this and many
other targets.
In the same fashion, we can now make use of the newly introduced
support for building seperate ramdisk to uImage.FIT with a dedicated
initrd blob checked and loaded by U-Boot instead of embedding the
cpio archive into the kernel itself.
This allows for having larger ramdisks, choosing ramdisk compression
independently of kernel compression (while only kernel is decompressed
by the bootloader) and for more easily replacing or modifying the
filesystem contained in an initramfs image.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
PCIe still reports link-down for some reason, RAID fails to assemble
despite SATA looking good (maybe a generic problem with RAID?)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* show only if target supports it (ie. seperate_ramdisk feature set)
* select XZ compression by default of ramdisk is seperate
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This was overlooked when adding support for this device.
(It has recently been discovered that this was the only device in
ath79 having &uart disabled.)
Fixes: acc6263013 ("ath79: add support for GL.iNet GL-USB150")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
That was a left-over from testing and should not have made it into the
tree. Remove it.
Fixes: 330bd380e8 ("image: allow building FIT and uImage with ramdisk")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[refresh again]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Previously, build would fail for targets containing devices with not
initramfs image (such as mpc85xx-p1010). Only generate the JSON image
info for the initramfs image when we have one to avoid breaking the
builds.
Fixes commit d3140d0529 ("build/json: generate json file for initramfs")
Signed-off-by: David Bauer <mail@david-bauer.net>
simplify maintaining mt7622-bananapi-bpi-r64-rootdisk.dts by
storing only differences between upstream dts
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
As PKG_LICENSE is originally set by include/trusted-firmware-a.mk it
can only be appended after that. Hence move that line below the
include to actually make sense.
(cosmetical change, already slipped into openwrt-21.02 branch)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This creates a shared DTSI for qca955x Senao/Engenius APs with
concatenated firmware partition/okli loader:
- EAP1200H
- EnstationAC v1
To make this usable for future boards with 32 MB flash as well,
split the partitions node already.
Suggested-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These recipes and definitions can apply
to devices from other vendors
with PCB boards or SDK produced by Senao
not only the brand Engenius
possible examples:
Extreme Networks, WatchGuard, OpenMesh,
Fortinet, ALLNET, OCEDO, Plasma Cloud, devolo, etc.
so rename all of these items
and move DEVICE_VENDOR from common to generic/tiny.mk
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This package had two patches (with two headers etc.) in one file,
which would have quilt merging them during a refresh.
Separate these patches into two files, as the original intent seems
to be having them separate.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
When using Shell arithmetric evaluation via $((..)) the variables in
the expression do not need to be prefixed by the '$' sign.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This creates a shared DTSI for ar934x Senao/Engenius APs:
- EAP300 v2
- ENS202EXT v1
- EAP600
- ECB600
Since ar9341/ar9344 have different configuration, this new file
mostly contains the partitioning.
Suggested-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This creates a shared DTSI for ar724x Senao/Engenius APs:
- ENH202 v1
- EAP350 v1
- ECB350 v1
Since ar7240/ar7242 have different configuration, this new file
mostly contains the partitioning.
Suggested-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The uart node is enabled on all devices except one (GL-USB150 *).
Thus, let's not have a few hundred nodes to enable it, but do not
disable it in the first place.
Where the majority of devices is using it, also move the serial0
alias to the DTSI.
*) Since GL-USB150 even defines serial0 alias, the missing uart
is probably just a mistake. Anyway, disable it for now so this
patch stays cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested on Pogoplug V4.
Linksys EA3500 will not build with buildbot settings and should be
disabled when the target is switched, unless the image size is
reduced again.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[add EA3500 comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Update config with make kernel_oldconfig.
CONFIG_SATA_PMP=y is added manually as done for 5.4.
This should be resolved properly in a separate issue.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[add back CONFIG_SATA_PMP, rebase/refresh]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
CONFIG_NET_DSA_MV88E6XXX_PTP was simply missing in generic config.
CONFIG_I2C_PXA_SLAVE was previously enabled via i2c-pxa package,
but got removed there without moving the symbol to generic config.
Fixes: dd13add3ce ("kernel: i2c-pxa: remove slave")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Check if firmware environment variable 'rootfs_data_max' exists and is
set to a numerical value greater than 0. If so, limit rootfs_data
volume to that size instead of using the maximum available size.
This is useful on devices with lots of flash where users may want to
have eg. a volume for persistent logs and statistics or for external
applications/containers. Persistence on rootfs overlay is limited by
the size of memory available during the sysugprade process as that
data needs to be copied to RAM while the volume is being recreated
during sysupgrade. Hence it is unsuitable for keeping larger amounts
of data accross upgrade which makes additional volume(s) for
application data desirable.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Instead of embedding the initrd cpio archive into the kernel, allow
for having an external ramdisk added to the FIT or uImage.
This is useful to overcome kernel size limitations present in many
stock bootloaders, as the ramdisk is then loaded seperately and doesn't
add to the kernel size. Hence we can have larger ramdisks to host ie.
installers with all binaries to flash included (or a web-based
firmware selector).
In terms of performance and total size the differences are neglectible.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow for single (external-data) FIT image to hold kernel, dtb and
squashfs. In that way, the bootloader verifies the system integrity
including the rootfs, because what's the point of checking that the
hash of the kernel is correct if it won't boot in case of squashfs
being corrupted? Better allow bootloader to check everything needed
to make it at least up to failsafe mode. As a positive side effect
this change also makes the sysupgrade process on nand potentially
much easier as it is now.
In short: mkimage has a parameter '-E' which allows generating FIT
images with 'external' data rather than embedding the data into the
device-tree blob itself. In this way, the FIT structure itself remains
small and can be parsed easily (rather than having to page around
megabytes of image content). This patch makes use of that and adds
support for adding sub-images of type 'filesystem' which are used to
store the squashfs. Now U-Boot can verify the whole OS and the new
partition parsers added in the Linux kernel can detect the filesystem
sub-images, create partitions for them, and select the active rootfs
volume based on the configuration in FIT (passing configuration via
device tree could be implemented easily at a later stage).
This new FIT partition parser works for NOR flash (on top of mtdblock),
NAND flash (on top of ubiblock) as well as classic block devices
(ie. eMMC, SDcard, SATA, NVME, ...).
It could even be used to mount such FIT images via `losetup -P` on a
user PC if this patch gets included in Linux upstream one day ;)
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The kernel bump to 5.4 has removed the mx25l25635f hack, and the
mx25l25635f compatible is no longer required.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Upstream integrated multiple patches from Distributions and did other
changes:
* rp-pppoe.so was renamed to pppoe.so
* Converted to ANSI C
The following patches were applied upstream:
* 100-debian_ip-ip_option.patch
* 101-debian_close_dev_ppp.patch
* 103-debian_fix_link_pidfile.patch
* 106-debian_stripMSdomain.patch
* 107-debian_pppoatm_wildcard.patch
* 110-debian_defaultroute.patch
* 202-no_strip.patch
Compilation with musl libc was fixed upstream so
140-pppoe_compile_fix.patch is not needed any more
Parts of the 203-opt_flags.patch patch were applied in a different way
upstream.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The packages feed has a proposed package for a GOST engine, which needs
support from the main openssl library. It is a default option in
OpenSSL. All that needs to be done here is to not disable it.
Package increases by a net 1-byte, so it is not really really worth
keeping this optional.
This commit also includes a commented-out example engine configuration
in openssl.cnf, as it is done for other available engines.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
As suggested by Sergio, this adds GPIOs 19 and 8 explicitly into the
DIR-860L DTS, so the PCI-E ports get reset and the N radio (radio1)
on PCI-E port 1 comes up reliably.
Fixes the following error that popped up in dmesg:
[ 1.638942] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
Suggested-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
This adds the necessary nuts and bolts for the uboot settings for both the ZyXEL GS1900-8HP v1 and v2.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
The Netgear R6800 and R6700v2 devices have a Semtech SX1503 GPIO
expander controlling the device LEDs. This expander was initially
supported on 4.14, but support was lost in the transition to 5.4.
Since this driver cannot be built as a kernel module, enable it in the
kernel config for all mt7621 devices.
Run-tested on a Netgear R6800.
Cc: Stijn Segers <foss@volatilesystems.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Biggest fix for this version is CVE-2021-3336, which has already been
applied here. There are a couple of low severity security bug fixes as
well.
Three patches are no longer needed, and were removed; the one remaining
was refreshed.
This tool shows no ABI changes:
https://abi-laboratory.pro/index.php?view=objects_report&l=wolfssl&v1=4.6.0&v2=4.7.0
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Marvell mv88e6xxx switch series cannot perform MAC learning from
CPU-injected (FROM_CPU) DSA frames, which results in 2 issues.
- excessive flooding, due to the fact that DSA treats those addresses
as unknown
- the risk of stale routes, which can lead to temporary packet loss
Backport those patch series from netdev mailing list, which solve these
issues by adding and clearing static entries to the switch's FDB.
Add a hack patch to set default VID to 1 in port_fdb_{add,del}. Otherwise
the static entries will be added to the switch's private FDB if VLAN
filtering disabled, which will not work.
The switch may generate an "ATU violation" warning when a client moves
from the CPU port to a switch port because the static ATU entry added by
DSA core still points to the CPU port. DSA core will then clear the static
entry so it is not fatal. Disable the warning so it will not confuse users.
Link: https://lore.kernel.org/netdev/20210106095136.224739-1-olteanv@gmail.com/
Link: https://lore.kernel.org/netdev/20210116012515.3152-1-tobias@waldekranz.com/
Ref: https://gitlab.nic.cz/turris/turris-build/-/issues/165
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
The update to gettext 0.21 broke packages that use autotools and
gettext because the sed line was failing with the new version. Fix with
a better sed expression.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Add symbol to generic config (this was added between 5.4 and 5.10),
and remove it from the targets where it was added by kernel_oldconfig
in the meantime.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There are efforts underway to bring wireguard in-tree for Linux 5.4 and
to have a common build infrastructure for both 5.4 and 5.10 for
kmod-wireguard[0]. Until then, restrict kmod-wireguard to build only on
Linux 5.4, because the wireguard-compat package will not build on Linux
5.10.
[0]: https://github.com/openwrt/openwrt/pull/3885
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Modify existing modules to reflect their new location in Linux 5.10. Add
missing dependenices.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
[enable CRYPTO_USER_API_ENABLE_OBSOLETE; add kmod-crypto-hash dependency
to usb-net-rtl8152]
Signed-off-by: David Bauer <mail@david-bauer.net>