The Bluesocket BSAP1880 board has a Vitesse PHY, for which the driver was
not being included, and its RedBoot directory block is earlier in the
flash than the search was allowing. This commit prepares for supporting it.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
The ag71xx code did not include a case for the "rgmii-id" PHY mode in the
code. There are devices that need this mode, so I'm adding it.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
The code for calculating the CRC32 signatures for RedBoot FIS partitions
was already included, but for unknown reasons, it was never invoked. Some
bootloaders enforce checking these for loaded kernels, so they should be
written. This patch does so.
Tested-by: Brian Gonyer <bgonyer@gmail.com>
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
To configure the list of allowable TLS 1.3 ciphersuites, the option
tls_ciphersuites is used instead of tls_ciphers.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Fix the following compilation error when using linux 4.19 on brcm47xx:
drivers/watchdog/old_gpio_wdt.c:236:2: error: implicit declaration of function 'setup_timer'
setup_timer was removed and replaced by timer_setup in linux >=4.15:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=513ae785
Update the patch to use the timer_setup interface
Signed-off-by: Zachary Cook <zachcook1991@gmail.com>
It was reported in FS#2385, that Carambola2 doesn't currently have
working watchdog so fix it by adding watchdog node.
Ref: FS#2385
Signed-off-by: Petr Štetiar <ynezz@true.cz>
ELECOM WRC-1167GHBK2-S has a MediaTek MT7615D chip for 2.4/5 GHz
wireless.
A driver package for MT7615 chip is added to OpenWrt in
a0e5ca4f35,
so add preliminary MT7615 chip support for WRC-1167GHBK2-S.
Note: Currently, DBDC mode for MT7615 is not supported in mt76 driver.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Redirect the build output to PKG_BUILD_DIR instead of copying over
complete source code.
Build tested on following targets:
x86/64 ar7/generic ipq40xx/generic imx6/generic ar71xx/generic
ramips/mt7621 ramips/mt7620 sunxi/cortexa7
Run tested on imx6/apalis.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Drop 211-host_tools_portability.patch which is breaking perf build on
4.19 kernels by removing the include directory from the host's CFLAGS
leading to the following build breakage:
pmu-events/jevents.c:48:10: fatal error: linux/list.h: No such file or directory
#include <linux/list.h>
^~~~~~~~~~~~~~
Signed-off-by: Petr Štetiar <ynezz@true.cz>
jffs2reset is used to cleanup the rootfs_data overlay, but it's
currently missing in the ramfs during sysupgrade leading to the
following error:
Switching to ramdisk...
Performing system upgrade...
/lib/upgrade/do_stage2: line 27: jffs2reset: not found
Fixes: 2f1a11d008 ("imx6: apalis: fix config survival after sysupgrade -n")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
We can't use $board_name in sysupgrade paths for kernel and rootfs as we
currently generate one image which could be used on two different base
boards.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Many Atom-based embedded/industrial x86 boards can't run 64bit operating
systems due to either processor or board firmware limitations, but they
have modern interfaces (PCIe) or have modern Intel gigabit controllers
onboard. With the current default package selection for x86 Generic
target their network won't work.
Add the modern gigabit network modules needed or most likely going to be
used as add-in cards, similar to what is the list on x86_64 target.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[fixed whitespace issue]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
By default, set BE tx queue TXOP limit to 1.0 in the hostapd config
Many vendor drivers are doing similar things to boost throughput.
On MT7612 under ideal conditions, it improves tx throughput from 470 Mbit/s
to about 570 Mbit/s.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
sysupgrade passes image path to platform_check_image() as an argument so
it can be simply accessed using $1
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The only step between platform_pre_upgrade() and platform_do_upgrade()
is switching to ramdisk. It should be fine to "mtd erase firmware" from
the later callback and get rid of the first one.
This change wasn't tested on affected target but identical code logic
was verified to work as expected on brcm47xx with initramfs firmware.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The only step between platform_pre_upgrade() and platform_do_upgrade()
is switching to ramdisk. It should be fine to "mtd erase firmware" from
the later callback and get rid of the first one.
This change wasn't tested on affected target but identical code logic
was verified to work as expected on brcm47xx with initramfs firmware.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
fixes intermittent loss of connectivity on 1Gbit port, with log message:
> 803x_aneg_done: SGMII link is not ok
Thanks to David Bauer for pointing me in the right direction.
I just had to figure out the right bus_id, which you find in this log:
> ag71xx ag71xx.1: connected to PHY at gpio-1:00 [uid=004dd074,
driver=Atheros 8031 ethernet]
Fixes FS#2236
Signed-off-by: Etienne Champetier <champetier.etienne@gmail.com>
[Wrapped commit message - Fixed whitespace erors]
Signed-off-by: David Bauer <mail@david-bauer.net>
This script is copied from ar71xx. Without a header fixup, u-boot
checksum for kernel will fail after the first boot.
Fixes: a9360452f0 ("ath79: add support for Qihoo C301")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
sysupgrade passes image to check as argument so use $# instead of $ARGC.
It also fits this function better as it checks $1 and not $ARGV.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
In 2011 (!), network setup for nexaira,bc2 was moved to network
defaults script with a typo so it became b2c:
295e04084c ("ramips: setup bc2 mac addresses from the generic network script")
This patch just removes the useless entry without replacement,
since it seems to have worked for 8 years anyway.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
according to functional block diagram in datasheet, these devices
don't belong to apb bus.
Move these nodes out to match datasheet description.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Specifications:
- SoC: AR9344
- RAM: 128MB
- Flash: 2 * 16MB (MX25L12845)
- Ethernet: 2 * FE LAN & 1 * FE WAN
- WiFi: 2.4G: AR9344 5G: QCA9882
Flash instruction:
1. Hold reset and power up the router
2. Set your IP to 192.168.1.x
3. Open 192.168.1.1 and upload the generated *factory* firmware
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Since mt76x8an ver1 eco2, SDXC pins can be switched to the
following pinmap:
sd_d1 -> PAD_I2S_SDI
sd_d0 -> PAD_I2S_WS
sd_cmd -> PAD_I2S_CLK
sd_d3 -> PAD_I2C_SCLK
sd_d2 -> PAD_I2C_SD
sd_clk -> PAD_GPIO0
sd_wp -> PAD_TXD1
sd_cd -> PAD_RXD1
To use this pinmap, one would need to set ESD_MODE bit (bit 15)
to 1 in GPIO1_MODE and switch other used pads into GPIO mode.
In this mode, we don't need to switch ethernet pins to digital
pad.
Check ESD_MODE bit before applying AGPIO_CFG and use rt_sysc_m32
to set it.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Removed an eglibc remnant, and while at it, grouped all of the
TOOLCHAIN_PLATFORMs using the same FLAGS together.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
The OpenWrt buildroot ABI version rebuild tracker does not handle
transient dependencies, therefore add all libraries linked by
block-mount and blockd as direct dependencies to the corresponding
binary package definition.
This ensures that block-mount and blockd is automatically rebuilt and
relinked if any of these libraries has its ABI_VERSION updated in the
future.
Fixes: FS#2373
[jow: similar fix for procd and 98.42% of commit message]
Signed-off-by: Jo-Philip Wich <jow@mein.io>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware
--------
CPU: Qualcomm Atheros QCA9558
RAM: 128M DDR2
FLASH: 16MiB
ETH: 1x Atheros AR8035 (PoE in)
WiFi2: QCA9558 3T3R
WiFi5: QCA9880 3T3R
BTN: 1x Reset
LED: 1x LED Power (non-controllable)
1x LED Status (internal)
1x LED LAN (controlled by PHY)
1x LED WLAN
BEEP: 1x GPIO attached piezo beeper
UART: 3.3V GND TX RX (115200-N-8) (3.3V is square pad)
Header is located next to external-LED header.
Installation
------------
Make sure you set a password for the root user as prompted on first
setup!
1. Upload OpenWRT sysupgrade image via SSH to the device.
Use /tmp as the destination folder on the device.
User is root, password the one set in the web interface.
2. Install OpenWRT with
> sysupgrade -n -F /tmp/<openwrt-image-name>
Signed-off-by: David Bauer <mail@david-bauer.net>
The command line enforced by the kernel is harmful, we want to
use the command line passed from the device tree. This is
especially important for the SQ201, Teltonika RUT and WBD111
which has a console set to 115200n8 and not 19200n8 like all
the others, so their consoles will be confusingly changing
baudrate between boot loader and kernel. The setting in the
device tree corresponds to what the boot loader is using.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch unifies the polled and interrupt-driven gpio_keys code
paths as well implements consistent handling of the debounce
interval set for the GPIO buttons and switches.
Hotplug events will only be fired if
1. The input changes its state and remains stable for the duration
of the debounce interval (default is 5 ms).
2. In the initial stable (no state-change for duration of the
debounce interval) state once the driver module gets loaded.
Switch type inputs will always report their stable state.
Unpressed buttons will not trigger an event for the initial
stable state. Whereas pressed buttons will trigger an event.
This is consistent with upstream's gpio-key driver that uses
the input subsystem (and dont use autorepeat).
Prior to this patch, this was handled inconsistently for interrupt-based
an polled gpio-keys. Hence this patch unifies the shared logic into the
gpio_keys_handle_button() function and modify both implementations to
handle the initial state properly.
The changes described in 2. ) . can have an impact on the
failsafe trigger. Up until now, the script checked for button
state changes. On the down side, this allowed to trigger the
failsafe by releasing a held button at the right time. On the
plus side, the button's polarity setting didn't matter.
Now, the failsafe will only engage when a button was pressed
at the right moment (same as before), but now it can
theoretically also trigger when the button was pressed the
whole time the kernel booted and well into the fast-blinking
preinit phase. However, the chances that this can happen are
really small. This is because the gpio-button module is usually
up and ready even before the preinit state is entered. So, the
initial pressed button event gets lost and most devices behave
as before.
Bisectors: If this patch causes a device to permanently go into
failsafe or experience weird behavior due to inputs, please
check the following:
- the GPIO polarity setting for the button
- the software-debounce value
Run-tested for 'gpio-keys' and 'gpio-keys-polled' on
- devolo WiFi pro 1200e
- devolo WiFi pro 1750c
- devolo WiFi pro 1750x
- Netgear WNDR4700
- Meraki MR24
- RT-AC58U
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [further
cleanups, simplification and unification]
- Support added to bcm2709 subtarget (32 bit).
- 64 bit kernel still requires many hacks on RPi 4B.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
b43legacy needs ssb support and we do not compile the mips74 subtarget
of the brcm47xx target with SSB support. This causes a build failure in
the mac80211 package and only some of the kernel modules are being
created.
I am not aware of any device with a BRCM47xx mips74 CPU which uses a
b43legacy compatible device.
Fixes: FS#2334
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SoC: MediaTek MT7621AT
RAM: 128M (Winbond W631GG6KB-15)
FLASH: 16MB (Spansion S25FL128SA)
WiFi: MediaTek MT7603EN bgn 2SS
WiFi: MediaTek MT7612EN nac 2SS
BTN: Reset - WPS
LED: - Power
- LAN {1-4}
- WAN
- WiFi 2.4 GHz
- WiFi 5 GHz
- USB
UART: UART is present next to the Power LED.
TX - RX - GND - 3V3 / 57600-8N1
3V3 is the nearest one to the Power LED.
Installation
------------
Via TFTP:
1. Set your computers IP-Address to 192.168.1.75.
2. Power up the Router with the Reset button pressed.
3. Release the Reset button after 5 seconds.
4. Upload OpenWRT sysupgrade image via TFTP:
> tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE>
Via SSH:
Note: User/password for SSH is identical with the one used in the
Web-interface.
1. Complete the initial setup wizard.
2. Activate SSH under "Administration" -> "System".
3. Transfer the OpenWrt sysupgrade image via scp:
> scp owrt.bin admin@192.168.1.1:/tmp
4. Connect via SSH to the router.
> ssh admin@192.168.1.1
5. Write the OpenWrt image to flash.
> mtd-write -i /tmp/owrt.bin -d linux
6. Reboot the router
> reboot
Signed-off-by: David Bauer <mail@david-bauer.net>
