This row is no longer necessary as it was replaced by LOCALVERSION in
uboot.mk, which explicitly sets OpenWrt version to all U-boot packages accross
OpenWrt. [1]
[1] d6aa9d9e07
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
The MBL has a 512KiB Microchip SST39VF040 chip for uboot and
not much else.
Thanks to Ewald who figured out that the "jedec-probe" vs.
"jedec-flash" was the wrong binding. With this information
and the jedec-probe support enabled => the chip works.
| physmap-flash 4fff80000.nor_flash: physmap platform flash device: [mem 0x4fff80000-0x4ffffffff]
| Found: SST 39LF040
| 4fff80000.nor_flash: Found 1 x8 devices at 0x0 in 8-bit bank
Suggested-by: Ewald Comhaire <e.comhaire@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware specification
----------------------
* RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz
* 128MB DRAM
* 32MB NOR Flash
* 16 x 10/100/1000BASE-T ports
- Internal PHY with 8 ports (RTL8218B)
- External PHY with 8 ports (RTL8218B)
* 4 x Gigabit RJ45/SFP Combo ports
- External PHY with 4 SFP ports (RTL8214FC)
* Power LED
* Reset button on front panel
* UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6
UART pinout
-----------
[o]ooo|J6
| ||`------ GND
| |`------- RX
| `-------- TX
`---------- Vcc (3V3)
Boot initramfs image from U-Boot
--------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000 openwrt-realtek-rtl838x-d-link_dgs-1210-20-initramfs-kernel.bin` command
5. Boot the image with `bootm` command
To install, upload the sysupgrade image to the OEM webpage or sysupgrade
from the system running from initramfs image.
It has been developed and tested on device with F1 revision.
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
[correct initramfs image name]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
4383528e0 P2P: Use weighted preferred channel list for channel selection
f2c5c8d38 QCA vendor attribute to configure RX link speed threshold for roaming
94bc94b20 Add QCA vendor attribute for DO_ACS to allow using existing scan entries
b9e2826b9 P2P: Filter 6 GHz channels if peer doesn't support them
d5a9944b8 Reserve QCA vendor sub command id 206..212
ed63c286f Remove space before tab in QCA vendor commands
e4015440a ProxyARP: Clear bridge parameters on deinit only if hostapd set them
02047e9c8 hs20-osu-client: Explicit checks for snprintf() result
cd92f7f98 FIPS PRF: Avoid duplicate SHA1Init() functionality
5c87fcc15 OpenSSL: Use internal FIPS 186-2 PRF with OpenSSL 3.0
9e305878c SAE-PK: Fix build without AES-SIV
c41004d86 OpenSSL: Convert more crypto_ec_key routines to new EVP API
667a2959c OpenSSL: crypto_ec_key_get_public_key() using new EVP_PKEY API
5b97395b3 OpenSSL: crypto_ec_key_get_private_key() using new EVP_PKEY API
177ebfe10 crypto: Convert crypto_ec_key_get_public_key() to return new ec_point
26780d92f crypto: Convert crypto_ec_key_get_private_key() to return new bignum
c9c2c2d9c OpenSSL: Fix a memory leak on crypto_hash_init() error path
6d19dccf9 OpenSSL: Free OSSL_DECODER_CTX in tls_global_dh()
4f4479ef9 OpenSSL: crypto_ec_key_parse_{priv,pub}() without EC_KEY API
b092d8ee6 tests: imsi_privacy_attr
563699174 EAP-SIM/AKA peer: IMSI privacy attribute
1004fb7ee tests: Testing functionality to discard DPP Public Action frames
355069616 tests: Add forgotten files for expired IMSI privacy cert tests
b9a222cdd tests: sigma_dut and DPP curve-from-URI special functionality
fa36e7ee4 tests: sigma_dut controlled STA and EAP-AKA parameters
99165cc4b Rename wpa_supplicant imsi_privacy_key configuration parameter
dde7f90a4 tests: Update VM setup example to use Ubuntu 22.04 and UML
426932f06 tests: EAP-AKA and expired imsi_privacy_key
35eda6e70 EAP-SIM peer: Free imsi_privacy_key on an error path
1328cdeb1 Do not try to use network profile with invalid imsi_privacy_key
d1652dc7c OpenSSL: Refuse to accept expired RSA certificate
866e7b745 OpenSSL: Include rsa.h for OpenSSL 3.0
bc99366f9 OpenSSL: Drop security level to 0 with OpenSSL 3.0 when using TLS 1.0/1.1
39e662308 tests: Work around reentrant logging issues due to __del__ misuse
72641f924 tests: Clean up failed test list in parallel-vm.py
e36a7c794 tests: Support pycryptodome
a44744d3b tests: Set ECB mode for AES explicitly to work with cryptodome
e90ea900a tests: sigma_dut DPP TCP Configurator as initiator with addr from URI
ed325ff0f DPP: Allow TCP destination (address/port) to be used from peer URI
e58dabbcf tests: DPP URI with host info
37bb4178b DPP: Host information in bootstrapping URI
1142b6e41 EHT: Do not check HE PHY capability info reserved fields
7173992b9 tests: Flush scan table in ap_wps_priority to make it more robust
b9313e17e tests: Update ap_wpa2_psk_ext_delayed_ptk_rekey to match implementation
bc3699179 Use Secure=1 in PTK rekeying EAPOL-Key msg 1/4 and 2/4
d2ce1b4d6 tests: Wait for request before responding in dscp_response
Compile-tested: all versions / ath79-generic, ramips-mt7621
Run-tested: hostapd-wolfssl / ath79-generic, ramips-mt7621
Signed-off-by: David Bauer <mail@david-bauer.net>
Downstream projects might re-generate device-specific configuration
based on OpenWrt's defaults on each upgrade, thus being unaffected by
forward- as well as backwards-breaking configuration.
Add a new sysupgrade parameter, which allows sysupgrades between minor
compat-versions. Upgrades will still fail upon mismatching major compat
versions.
Signed-off-by: David Bauer <mail@david-bauer.net>
11f5c7b fw4.uc: fix zone helper assignment
b9d35ff fw4.uc: don't skip zone for unavailable helper
e35e26b tests: add test for zone helpers
a063317 ruleset: fix conntrack helpers
e1cb763 ruleset: reuse zone-jump.uc template for notrack and helper chain jumps
11410b8 ruleset: reorder declarations & output tweaks
880dd31 fw4: fix skipping invalid IPv6 ipset entries
5994466 fw4: simplify `is_loopback_dev()`
53886e5 fw4: fix crash in parse_cthelper() if no helpers are present
11256ff fw4: add support for configurable includes
3b5a033 tests: add test coverage for firewall includes
d79911c fw4: support sets with timeout capability but without default expiry
15c3831 fw4: add support for `option log` in rule and redirect sections
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Select matching U-Boot for both v1 and v2 variants.
Fixes: 15a02471bb ("mediatek: new target mt7622-ubnt-unifi-6-lr-v1")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Before this change UCI sections of both types were parsed in order as
specified in UCI. That didn't work well with all drivers (e.g. b53).
It seems that VLAN setup can reset / overwrite previously set ports
parameters. It resulted in "switch_port" options defined above
"switch_vlan"s being silently ignored.
Ideally swconfig & all drivers should be improved to handle that
properly but it'd be a waste of time at this point as DSA replaces
swconfig. Use this minor parsing change as a quick fix.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
MTS WG430223 is a wireless AC1300 (WiFi 5) router manufactured by
Arcadyan company. It's very similar to Beeline Smartbox Flash (Arcadyan
WG443223).
Device specification
--------------------
SoC Type: MediaTek MT7621AT
RAM: 128 MiB
Flash: 128 MiB (Winbond W29N01HV)
Wireless 2.4 GHz (MT7615DN): b/g/n, 2x2
Wireless 5 GHz (MT7615DN): a/n/ac, 2x2
Ethernet: 3xGbE (WAN, LAN1, LAN2)
USB ports: No
Button: 1 (Reset/WPS)
LEDs: 2 (Red, Green)
Power: 12 VDC, 1 A
Connector type: Barrel
Bootloader: U-Boot (Ralink UBoot Version: 5.0.0.2)
OEM: Arcadyan WG430223
Installation
------------
1. Login to the router web interface (superadmin:serial number)
2. Navigate to Administration -> Miscellaneous -> Access control lists &
enable telnet & enable "Remote control from any IP address"
3. Connect to the router using telnet (default admin:admin)
4. Place *factory.trx on any web server (192.168.1.2 in this example)
5. Connect to the router using telnet shell (no password required)
6. Save MAC adresses to U-Boot environment:
uboot_env --set --name eth2macaddr --value $(ifconfig | grep eth2 | \
awk '{print $5}')
uboot_env --set --name eth3macaddr --value $(ifconfig | grep eth3 | \
awk '{print $5}')
uboot_env --set --name ra0macaddr --value $(ifconfig | grep ra0 | \
awk '{print $5}')
uboot_env --set --name rax0macaddr --value $(ifconfig | grep rax0 | \
awk '{print $5}')
7. Ensure that MACs were saved correctly:
uboot_env --get --name eth2macaddr
uboot_env --get --name eth3macaddr
uboot_env --get --name ra0macaddr
uboot_env --get --name rax0macaddr
8. Download and write the OpenWrt images:
cd /tmp
wget http://192.168.1.2/factory.trx
mtd_write erase /dev/mtd4
mtd_write write factory.trx /dev/mtd4
9. Set 1st boot partition and reboot:
uboot_env --set --name bootpartition --value 0
Back to Stock
-------------
1. Run in the OpenWrt shell:
fw_setenv bootpartition 1
reboot
2. Optional step. Upgrade the stock firmware with any version to
overwrite the OpenWrt in Slot 1.
MAC addresses
-------------
+-----------+-------------------+----------------+
| Interface | MAC | Source |
+-----------+-------------------+----------------+
| label | A4:xx:xx:51:xx:F4 | No MACs was |
| LAN | A4:xx:xx:51:xx:F6 | found on Flash |
| WAN | A4:xx:xx:51:xx:F4 | [1] |
| WLAN_2g | A4:xx:xx:51:xx:F5 | |
| WLAN_5g | A6:xx:xx:21:xx:F5 | |
+-----------+-------------------+----------------+
[1]:
a. Label wasb't found neither in factory nor in other places.
b. MAC addresses are stored in encrypted partition "glbcfg". Encryption
key hasn't known yet. To ensure the correct MACs in OpenWrt, a hack
with saving of the MACs to u-boot-env during the installation was
applied.
c. Default Ralink ethernet MAC address (00:0C:43:28:80:A0) was found in
"Factory" 0xfff0. It's the same for all MTS WG430223 devices. OEM
firmware also uses this MAC when initialazes ethernet driver. In
OpenWrt we use it only as internal GMAC (eth0), all other MACs are
unique. Therefore, there is no any barriers to the operation of several
MTS WG430223 devices even within the same broadcast domain.
Stock firmware image format
---------------------------
The same as Beeline Smartbox Flash but with another trx magic
+--------------+---------------+----------------------------------------+
| Offset | | Description |
+==============+===============+========================================+
| 0x0 | 31 52 48 53 | TRX magic "1RHS" |
+--------------+---------------+----------------------------------------+
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Fix hostapd feature detection after the bump to 2022-05-08.
getopt was not updated correctly after upstream added support for -q arg.
This reenables feature detection so that LuCi can check for features like
SAE, fast roaming etc.
Fixes: c35ff1affe ("hostapd: update to 2022-05-08")
Signed-off-by: Robert Marko <robimarko@gmail.com>
902b321 wireless-regdb: Update regulatory rules for Israel (IL)
20f6f34 wireless-regdb: add missing spaces for US S1G rules
25652b6 wireless-regdb: Update regulatory rules for Australia (AU)
081873f wireless-regdb: update regulatory database based on preceding changes
166fbdd wireless-regdb: add db files missing from previous commit
e3f03f9 Regulatory update for 6 GHz operation in Canada (CA)
888da5f Regulatory update for 6 GHz operation in United States (US)
647bcaa Regulatory update for 6 GHz operation in FI
c6b079d wireless-regdb: update regulatory rules for Bulgaria (BG) on 6GHz
2ed39be wireless-regdb: Remove AUTO-BW from 6 GHz rules
7a6ad1a wireless-regdb: Unify 6 GHz rules for EU contries
68a8f2f wireless-regdb: update regulatory database based on preceding changes
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
7e06706 iw: event: report missing radar events
5909e73 iw: survey: add support for radio stats
64bf570 update nl80211.h
0900996 iw: print Radar background capability if supported
56c6077 iw: print out assoc comeback event
a4e5418 iw: support 160MHz frequency command for 6GHz band
5a71b72 iw: Print local EHT capabilities
e3287a1 station: print EHT rate information
ff67fb2 iw: fix double tab in mesh path header
05a5267 iw: fix 'upto' -> 'up to'
00a2985 iw: handle VHT extended NSS
82e0bd1 update nl80211.h
c95877c info: add missing extended features
0976378 info: refactor extended features
79f20cb bump version to 5.19
Sync nl80211.h with our version of mac80211 and remove parts of the iw
code that are not supported by our version of mac80211.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Sync nl80211.h with upstream in order to maintain parity with
nl80211_copy.h shipped with hostapd.
This is necessary, as currently the enum value for
NL80211_EXT_FEATURE_RADAR_BACKGROUND mismatches between hostapd and
mac80211. This breaks background radar capability detection in hostapd.
Reported-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David Bauer <mail@david-bauer.net>
Openvpn forces CONFIG_WOLFSSL_HAS_OPENVPN=y. When the phase1 bots build
the now non-shared package, openvpn will not be selected, and WolfSSL
will be built without it. Then phase2 bots have CONFIG_ALL=y, which
will select openvpn and force CONFIG_WOLFSSL_HAS_OPENVPN=y. This
changes the version hash, causing dependency failures, as shared
packages expect the phase2 hash.
Fixes: #9738
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
libwolfssl-benchmark should NOT be compiled as nonshared but
currently there is a bug where, on buildbot stage2, the package
is recompiled to build libwolfssl-benchmark and the dependency
change to the new libwolfssl version.
Each dependant package will now depend on the new wolfssl package
instead of the one previously on stage1 that has a different package
HASH.
Set the nonshared PKGFLAGS global while this gets investigated
and eventually fixed.
Fixes: 0a2edc2714 ("wolfssl: enable CPU crypto instructions")
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
commit c3a4cddaaf ("hostapd: remove hostapd-hs20 variant")
as well as
commit 9f1927173a ("hostapd: wpas: add missing config symbols")
indicate hostapd-full should support Hotspot 2.0 already, but only
wpa_supplicant (and wpad) do.
How this happened is not really clear, as no commit adding support for
Hotspot 2.0 is in the history.
Fix this and add Hotspot 2.0 capability to hostapd-full.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add the current BSS color to hostapd get_status method. This field is
set to -1 in case BSS color is not active for the BSS.
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
In case no specific BSS color is configured, set it to a random value.
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Update hostapd to Git HEAD from 2022-05-08. This allows us to take
advantage of background radar-detection as well as BSS color collision
detection.
Suggested-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David Bauer <mail@david-bauer.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
This patch allows the user to set `auth_server` and related settings on
non WPA2 Enterprise AP modes in `/etc/config/wireless`, too, so the
Radius Attributes for Dynamic VLAN Assignment can be fetched from Radius.
Without this patch, `auth_server` and other needed options are only
written to `hostapd-phy<n>.conf` when `option encryption wpa2` is set.
`hostapd` however supports "Station MAC address -based authentication" for
non WPA Enterprise Modes, too.
A classic approch is to use `accept_mac_file` which contains MAC addr
and VLAN-ID pairs. But, using `accept_mac_file` does not support
VLAN assignment for unknown stations.
This is a sample `freeradius3` config, where a known station
("7e:a6:a7:2a:93:d2") is assigned to VLAN `65` and unknown stations are
assigned to VLAN `67`.
```
"7ea6a72a93d2" Cleartext-Password := "7ea6a72a93d2"
Tunnel-Type = "VLAN",
Tunnel-Medium-Type = "IEEE-802",
Tunnel-Private-Group-Id = 65
DEFAULT Cleartext-Password := "%{User-Name}"
Tunnel-Type = "VLAN",
Tunnel-Medium-Type = "IEEE-802",
Tunnel-Private-Group-Id = 67
```
Other option is to configure known stations via `accept_mac_file` and
using only Radius for unknown stations.
I tested this patch only with `wpa_key_mgmt=WPA-PSK`, and assumed that
it should work with other Encryption/Access Mode, too.
Signed-off-by: Bernd Naumann <bernd.naumann@kr217.de>
This enables AES & SHA CPU instructions for compatible armv8, and x86_64
architectures. Add this to the hardware acceleration choice, since they
can't be enabled at the same time.
The package was marked non-shared, since the arm CPUs may or may not
have crypto extensions enabled based on licensing; bcm27xx does not
enable them. There is no run-time detection of this for arm.
NOTE:
Should this be backported to a release branch, it must be done shortly
before a new minor release, because the change to nonshared will remove
libwolfssl from the shared packages, but the nonshared are only built in
a subsequent release!
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Enabling different hardware crypto acceleration should not change the
library ABI. Add them to PKG_CONFIG_DEPENDS after the ABI version hash
has been computed.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
Delete the crypto-lib-blake2s kmod package, as BLAKE2s is now built-in.
Patches automatically rebased.
Build system: x86_64
Build-tested: ipq806x/R7800, x86/64
Signed-off-by: John Audia <therealgraysky@proton.me>
The ZyXEL GS1900-24E is a 24 port gigabit switch similar to other GS1900
switches.
Specifications
--------------
* Device: ZyXEL GS1900-24E
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB Macronix MX25L12835F
* RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8GE
* Ethernet: 24x 10/100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
24 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESET" button on front panel
* Switch: 1 Power switch on rear of device
* Power 120-240V AC C13
* UART: 1 serial header (JP2) with populated standard pin connector on
the left side of the PCB.
Pinout (front to back):
+ Pin 1 - VCC marked with white dot
+ Pin 2 - RX
+ Pin 3 - TX
+ PIn 4 - GND
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
file and select open so File Path is updated with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-24E is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-rtl838x-zyxel_gs1900-24e-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-rtl838x-zyxel_gs1900-24e-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Raylynn Knight <rayknight@me.com>
All known users of this ubus method have been updated to use the new
bss_transition_request method instead.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: David Bauer <mail@david-bauer.net>
Major changes are:
Add support for smbd-direct multi-desctriptor.
Add support for dkms.
Add support for key exchange.
Fix seveal bugs.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331].
Specification
-------------
SOC: Qualcomm IPQ4018
WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n
WiFi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac
Bluetooth: Qualcomm CSR8811 (A12U)
Ethernet: Qualcomm QCA8072 (2-port)
SPI Flash 1: Mactronix MX25L1605D (2MB)
SPI Flash 2: Winbond W25M02GV (256MB)
DRAM: Nanya NT5CC128M16IP-DI (256MB)
LED Controller: NXP PCA963x (I2C)
Buttons: Single reset button (GPIO).
Notes
-----
There does not appear to be a way to trigger TFTP recovery without entering
U-Boot. The device must be opened to access the serial console in order to
first flash OpenWrt onto a device from factory.
The device has automatic recovery backed by a second set of partitions on
the larger of the two SPI flash ICs. Both the primary and secondary must
be flashed to prevent accidental rollback to "factory" after 3 failed boot
attempts.
Serial console
--------------
A serial console is available on the following pins of the populated J2
connector on the device mainboard (115200 8n1).
(<-- Top of PCB / Device)
J2
[o o o o o o]
| | |
| | `-- GND
| `---- TX
`--------- RX
Installation instructions
-------------------------
1. Setup TFTP server with server IP set to 192.168.1.236.
2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Revert to "factory"
-------------------
1. Download latest firmware update from vendor support site.
2. Copy extracted `.img` file to `nodes-jr.img` in tftp root.
3. Connect to console using pinout detailed in the serial console section.
4. Power on device and press enter when prompted to drop into U-Boot.
5. Flash first partition device via `run flashimg`.
6. Once complete, reset device and allow to power up completely.
7. Once comfortable with device upgrade reboot and drop back into U-Boot.
8. Flash the second partition (recovery) via `run flashimg2`.
Link: https://github.com/openwrt/openwrt/pull/3682
Signed-off-by: Peter Adkins <peter@sunkenlab.com>
(calibration from nvmem, updated to 5.10+5.15)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Make ar8216/8327 swconfig driver modularizable and add
entry to the netdevices.mk kernel modules file.
Signed-off-by: Christian 'Ansuel' Marangi <ansuelsmth@gmail.com>
latency and short-term fairness is improved by fixing the tx queue sorting
so that it considers the pending AQL budget
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Needed by strongSwan IPsec VPN for strongswan-mod-chapoly. Not to be confused with
kmod-crypto-LIB-chacha20poly1305, which is an 8-byte nonce version used
by wireguard.
Signed-off-by: Xu Wang <xwang1498@gmx.com>
Aruba deploys a BDF in the root filesystem, however this matches the one
used for the DK04 reference board.
The board-specific BDFs are built into the kernel. The AP-365 shows
sinificant degraded performance with increased range when used with the
reference BDF.
Replace the BDF with the one extracted from Arubas kernel.
Signed-off-by: David Bauer <mail@david-bauer.net>
2f793a4 lua: add optional path filter to objects() method
2bebf93 ubusd: handle invoke on event object without data
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2e1fcf4 netifd: fix hwmode for 60g band
39ef9fe interface-ip: fix memory corruption bug when using jail network namespaces
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
557c98e init: selinux: don't relabel virtual filesystems
7a00968 init: only relabel rootfs if started from initramfs
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
210991d fw4: prefer /dev/stdin if available
4e5e322 fw4: make `fw4 restart` behavior more robust
221040e ruleset: emit time ranges when both start and stop times are specified
30a7d47 fw4: fix datetime parsing
fb9a6b2 ruleset: correct mangle_output chain type
6dd2617 fw4: fix logic flaw in testing hw flow offloading support
c7c9c84 fw4: ensure that negative bitcounts are properly translated
c4a78ed fw4: fix typo in emitted set types
Fixes: #9764, #9923, #9927, #9935, #9955
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
