1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The CONFIG_USERIO option is unset in multiple target configurations. On
the sunxi target it is activated. Move the kernel configuration option
to the generic kernel configuration.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Instead of deactivating this in every target config, deactivate it once
in the generic kernel config. I was asked for this config option in a
x86 64 build in OpenWrt 21.02.
Fixes: 87046e87e2 ("kernel: add missing kernel config symbol")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Bump to 5.10.26 reversed dependencies on IOMMU for CONFIG_VFIO thus
malta (at least) prompted for this new symbol.
Set it to 'false' in the default config. rockchip & X86 enable it in
target specific configs.
Thanks to Tony Ambardar for falling over this one
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
It's helpful for accessing booting data (DTS, kernel, etc.). It has to
be used carefully as CFE's JFFS2 support is quite dumb. It doesn't
recognize deleted files and has problems handling 0 inode.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Straightforward refresh of patches using update_kernel.
Removed (reverse-applicable):
bmips/patches-5.10/010-v5.11-net-dsa-implement-a-central-TX-reallocation-procedur.patch
Run tested: x86_64 (apu2)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Straightforward refresh of patches using update_kernel.
Run tested: x86_64 (apu2)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Manually rebased:
bcm27xx/950-0993-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
layerscape/701-net-0231-enetc-Use-DT-protocol-information-to-set-up-the-port.patch
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[remove accidental whitespace edit]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
With kernel 5.10, exfat is out of staging and in tree.
Added small hack to make it work with kernel 5.4 as well.
Added removed config options for 5.4 to generic config.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
[Set CONFIG_EXFAT_ config options to default values]
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update 5.10 generic config to add missing options prompting during builds,
when setting CONFIG_ALL_KMODS. Refresh the x86 subtargets to drop symbols
added to the generic config.
Also fix a typo in 5.4/5.10 generic configs: "CONFIG_CONFIG_KVM_AMD_SEV".
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
A SPI NOR flash should not be target-specific, so move it to generic in
case another platform needs to use it.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Backport upstream patch that fixes TRGMII mode now that mt7530 is
actually resetting the switch on ramips devices.
Patches apply to both Linux 5.4 and 5.10, since TRGMII is broken on both.
Fixes: 69551a2442 ("ramips: manage low reset lines")
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Add kmod-mdio-devres package and kernel config symbol, and update related
kmod-r8169 and kmod-ixgbe package dependencies.
Build tested module dependencies on x86/64 with CONFIG_ALL_KMODS=y.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
It's meant to provide upstream support for mtd & NVMEM. It's required
e.g. for reading MAC address from mtd partition content. It seems to be
in a final shape so it's worth testing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
It appears to be an automatic Kconfig symbol that varies depending on
the host platform. There is no need to define it in target configs, so
filter it out.
Also sort config-filter entries alphabetically.
Cc: Adrian Schmutzler <mail@adrianschmutzler.de>
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Also add a new kconfig symbol (CONFIG_KCMP) to the generic config,
disabling the SYS_kcmp syscall (it was split from
CONFIG_CHECKPOINT_RESTORE, which is disabled by default, so the
previous behaviour is kept).
Removed (upstreamed) patches:
070-net-icmp-pass-zeroed-opts-from-icmp-v6-_ndo_send-bef.patch
081-wireguard-device-do-not-generate-ICMP-for-non-IP-pac.patch
082-wireguard-queueing-get-rid-of-per-peer-ring-buffers.patch
083-wireguard-kconfig-use-arm-chacha-even-with-no-neon.patch
830-v5.12-0002-usb-serial-option-update-interface-mapping-for-ZTE-P685M.patch
Manually rebased patches:
313-helios4-dts-status-led-alias.patch
104-powerpc-mpc85xx-change-P2020RDB-dts-file-for-OpenWRT.patch
Run tested:
ath79 (TL-WDR3600)
mvebu (Turris Omnia)
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
From the original commit message:
"With GCC 10, building usbip triggers error for multiple definition
of 'udev_context', in:
- libsrc/vhci_driver.c:18 and
- libsrc/usbip_host_common.c:27.
Declare as extern the definition in libsrc/usbip_host_common.c."
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
REFCOUNT_FULL was removed for linux 5.5:
commit fb041bb7c0a9 (locking/refcount: Consolidate implementations of refcount_t)
COMMON_CLK_VERSATILE was removed on linux 5.8:
commit 5f55f1fb187d (clk: versatile: Fix kconfig dependency on COMMON_CLK_VERSATILE)
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The BCM5365 UID was updated in the driver, but we should also update it in the
fixup.
Fixes: cbcac4fde8 ("kernel: b53: update the BCM5365 UID")
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(Ammend commit description, add Fixes tag)
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
5.4.102 backported a lot of stuff that our WireGuard backport already
did, in addition to other patches we had, so those patches were
removed from that part of the series. In the process other patches were
refreshed or reworked to account for upstream changes.
This commit involved `update_kernel.sh -v -u 5.4`.
Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Compile testing i.mx6 with ALL_KMODS=y, PACKAGE_perf=y and bunch of
tracing/probing symbols has unveiled bunch of missing config options so
add them.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
These make a big difference when doing WireGuard with small armv7
routers, and the 5.4 backport already has it.
Suggested-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Without this patch, the chacha block counter is not incremented on neon
rounds, resulting in incorrect calculations and corrupt packets.
This also switches to using `--no-numbered --zero-commit` so that future
diffs are smaller.
Reported-by: Hans Geiblinger <cybrnook2002@yahoo.com>
Reviewed-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This adds the latest version of ofpart commit. It hopefully
1. Doesn't break compilation
2. Doesn't break partitioning
(this time).
It's required to implement fixed partitioning with some quirks. It's
required by bcm53xx, bcm4908, kirkwood, lantiq and mvebu.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This is useful for dual-boot setups where the loader sets variables depending
on the flash boot partition.
For example the Linksys E8450 sets mtdparts=master for the first partition
and mtdparts=slave for the second one.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce a magic GUID_PARTITION_LINUX_FIT_GUID to designate a GPT
partition to be interpreted by the FIT partition parser.
In that way, sub-partitions for (external-data) uImage.FIT stored
directly in a partition can be split, similar like we do for devices
with raw flash storage.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The CPU_MIPS64 and CPU_MIPS32 variables are supposed to be able to
distinguish broadly between 64-bit and 32-bit MIPS CPUs. However, they
weren't selected by the specialty CPUs, Octeon and Loongson, which meant
it was possible to hit a weird state of:
MIPS=y, CONFIG_64BIT=y, CPU_MIPS64=n
This commit rectifies the issue by having CPU_MIPS64 be selected when
the missing Octeon or Loongson models are selected.
In particular, this affects our octeonplus target.
It has been posted to LKML here:
https://lore.kernel.org/linux-mips/20210227122605.2680138-1-Jason@zx2c4.com/
Cc: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
BCM63XX internal PHYs and BCM5365 SoC internal switch are both using the
same phy_driver->phy_id, causing conflicts and unnecessary probes. E.g
the BCM63XX phy internal IRQ is lost on the first probe.
The full BCM5365 UID is 0x00406370.
Use an additional byte to mask the BCM5365 UID to avoid duplicate driver
phy_id's. This will fix the IRQ issue in internal BCM63XX PHYs and avoid
more conflicts in the future.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Rather than using the clunky, old, slower wireguard-linux-compat out of
tree module, this commit does a patch-by-patch backport of upstream's
wireguard to 5.4. This specific backport is in widespread use, being
part of SUSE's enterprise kernel, Oracle's enterprise kernel, Google's
Android kernel, Gentoo's distro kernel, and probably more I've forgotten
about. It's definately the "more proper" way of adding wireguard to a
kernel than the ugly compat.h hell of the wireguard-linux-compat repo.
And most importantly for OpenWRT, it allows using the same module
configuration code for 5.10 as for 5.4, with no need for bifurcation.
These patches are from the backport tree which is maintained in the
open here: https://git.zx2c4.com/wireguard-linux/log/?h=backport-5.4.y
I'll be sending PRs to update this as needed.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
ZTE MF283+ is a dual-antenna LTE category 4 router, based on Ralink
RT3352 SoC, and built-in ZTE P685M PCIe MiniCard LTE modem.
Hardware highlighs:
- CPU: MIPS24KEc at 400MHz,
- RAM: 64MB DDR2,
- Flash: 16MB SPI,
- Ethernet: 4 10/100M port switch with VLAN support,
- Wireless: Dual-stream 802.11n (RT2860), with two internal antennas,
- WWAN: Built-in ZTE P685M modem, with two internal antennas and two
switching SMA connectors for external antennas,
- FXS: Single ATA, with two connectors marked PHONE1 and PHONE2,
internally wired in parallel by 0-Ohm resistors, handled entirely by
internal WWAN modem.
- USB: internal miniPCIe slot for modem,
unpopulated USB A connector on PCB.
- SIM slot for the WWAN modem.
- UART connector for the console (unpopulated) at 3.3V,
pinout: 1: VCC, 2: TXD, 3: RXD, 4: GND,
settings: 57600-8-N-1.
- LEDs: Power (fixed), WLAN, WWAN (RGB),
phone (bicolor, controlled by modem), Signal,
4 link/act LEDs for LAN1-4.
- Buttons: WPS, reset.
Installation:
As the modem is, for most of the time, provided by carriers, there is no
possibility to flash through web interface, only built-in FOTA update
and TFTP recovery are supported.
There are two installation methods:
(1) Using serial console and initramfs-kernel - recommended, as it
allows you to back up original firmware, or
(2) Using TFTP recovery - does not require disassembly.
(1) Using serial console:
To install OpenWrt, one needs to disassemble the
router and flash it via TFTP by using serial console:
- Locate unpopulated 4-pin header on the top of the board, near buttons.
- Connect UART adapter to the connector. Use 3.3V voltage level only,
omit VCC connection. Pin 1 (VCC) is marked by square pad.
- Put your initramfs-kernel image in TFTP server directory.
- Power-up the device.
- Press "1" to load initramfs image to RAM.
- Enter IP address chosen for the device (defaults to 192.168.0.1).
- Enter TFTP server IP address (defaults to 192.168.0.22).
- Enter image filename as put inside TFTP server - something short,
like firmware.bin is recommended.
- Hit enter to load the image. U-boot will store above values in
persistent environment for next installation.
- If you ever might want to return to vendor firmware,
BACK UP CONTENTS OF YOUR FLASH NOW.
For this router, commonly used by mobile networks,
plain vendor images are not officially available.
To do so, copy contents of each /dev/mtd[0-3], "firmware" - mtd3 being the
most important, and copy them over network to your PC. But in case
anything goes wrong, PLEASE do back up ALL OF THEM.
- From under OpenWrt just booted, load the sysupgrade image to tmpfs,
and execute sysupgrade.
(2) Using TFTP recovery
- Set your host IP to 192.168.0.22 - for example using:
sudo ip addr add 192.168.0.22/24 dev <interface>
- Set up a TFTP server on your machine
- Put the sysupgrade image in TFTP server root named as 'root_uImage'
(no quotes), for example using tftpd:
cp openwrt-ramips-rt305x-zte_mf283plus-squashfs-sysupgrade.bin /srv/tftp/root_uImage
- Power on the router holding BOTH Reset and WPS buttons held for around
5 seconds, until after WWAN and Signal LEDs blink.
- Wait for OpenWrt to start booting up, this should take around a
minute.
Return to original firmware:
Here, again there are two possibilities are possible, just like for
installation:
(1) Using initramfs-kernel image and serial console
(2) Using TFTP recovery
(1) Using initramfs-kernel image and serial console
- Boot OpenWrt initramfs-kernel image via TFTP the same as for
installation.
- Copy over the backed up "firmware.bin" image of "mtd3" to /tmp/
- Use "mtd write /tmp/firmware.bin /dev/mtd3", where firmware.bin is
your backup taken before OpenWrt installation, and /dev/mtd3 is the
"firmware" partition.
(2) Using TFTP recovery
- Follow the same steps as for installation, but replacing 'root_uImage'
with firmware backup you took during installation, or by vendor
firmware obtained elsewhere.
A few quirks of the device, noted from my instance:
- Wired and wireless MAC addresses written in flash are the same,
despite being in separate locations.
- Power LED is hardwired to 3.3V, so there is no status LED per se, and
WLAN LED is controlled by WLAN driver, so I had to hijack 3G/4G LED
for status - original firmware also does this in bootup.
- FXS subsystem and its LED is controlled by the
modem, so it work independently of OpenWrt.
Tested to work even before OpenWrt booted.
I managed to open up modem's shell via ADB,
and found from its kernel logs, that FXS and its LED is indeed controlled
by modem.
- While finding LEDs, I had no GPL source drop from ZTE, so I had to probe for
each and every one of them manually, so this might not be complete -
it looks like bicolor LED is used for FXS, possibly to support
dual-ported variant in other device sharing the PCB.
- Flash performance is very low, despite enabling 50MHz clock and fast
read command, due to using 4k sectors throughout the target. I decided
to keep it at the moment, to avoid breaking existing devices - I
identified one potentially affected, should this be limited to under
4MB of Flash. The difference between sysupgrade durations is whopping
3min vs 8min, so this is worth pursuing.
In vendor firmware, WWAN LED behaviour is as follows, citing the manual:
- red - no registration,
- green - 3G,
- blue - 4G.
Blinking indicates activity, so netdev trigger mapped from wwan0 to blue:wwan
looks reasonable at the moment, for full replacement, a script similar to
"rssileds" would need to be developed.
Behaviour of "Signal LED" in vendor firmware is as follows:
- Off - no signal,
- Blinking - poor coverage
- Solid - good coverage.
A few more details on the built-in LTE modem:
Modem is not fully supported upstream in Linux - only two CDC ports
(DIAG and one for QMI) probe. I sent patches upstream to add required device
IDs for full support.
The mapping of USB functions is as follows:
- CDC (QCDM) - dedicated to comunicating with proprietary Qualcomm tools.
- CDC (PCUI) - not supported by upstream 'option' driver yet. Patch
submitted upstream.
- CDC (Modem) - Exactly the same as above
- QMI - A patch is sent upstream to add device ID, with that in place,
uqmi did connect successfully, once I selected correct PDP context
type for my SIM (IPv4-only, not default IPv4v6).
- ADB - self-explanatory, one can access the ADB shell with a device ID
added to 51-android.rules like so:
SUBSYSTEM!="usb", GOTO="android_usb_rules_end"
LABEL="android_usb_rules_begin"
SUBSYSTEM=="usb", ATTR{idVendor}=="19d2", ATTR{idProduct}=="1275", ENV{adb_user}="yes"
ENV{adb_user}=="yes", MODE="0660", GROUP="plugdev", TAG+="uaccess"
LABEL="android_usb_rules_end"
While not really needed in OpenWrt, it might come useful if one decides to
move the modem to their PC to hack it further, insides seem to be pretty
interesting. ADB also works well from within OpenWrt without that. O
course it isn't needed for normal operation, so I left it out of
DEVICE_PACKAGES.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove kmod-usb-ledtrig-usbport, take merged upstream patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
[refresh again]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
