This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
This removes the wan_mac setup for the following devices as they
do not set up a MAC address for ethernet in the first place:
- asiarf,awapn2403
- belkin,f7c027
- dlink,dir-615-d
- mofinetwork,mofi3500-3gn
- prolink,pwh2004
- ralink,v22rw-2x2
- unbranded,wr512-3gn-4m
- unbranded,wr512-3gn-8m
While at it, make some DT node labels consistent with the label
property.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
This removes the wan_mac setup for ralink,v11st-fe as this device
does not set up a MAC address for ethernet in the first place.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
While at it, change the partition label for zyxel,keenetic-extra-ii
to factory to be consistent with node label and all the other devices.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This uses the flash locations instead of eth0 MAC address to
calculate MAC address increments for WAN.
The change will make the MAC address setup of a particular device
more obvious and removes the dependency of 02_network on the eth0
initialization.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The evaluation boards do not set up a MAC address for eth0
in the first place, so it does not make sense to calculate a WAN
address from the random MAC used there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The TP-Link Archer C20i/C20 v1/C50 v1 seem to be almost the same,
so creating a common DTSI will reduce duplicate code.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The DTS variable has been removed in 402138d12d ("ramips: Derive
DTS name from device name in Makefile"), but the DEVICE_VARS entry
has been overlooked.
Remove it now since we are not using this variable.
This must _not_ be backported to 19.07, where the variable is still
in use.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The switch LAN port numbers are in reversed order with original config.
With this patch they are fixed.
Port order checked on both devices.
Signed-off-by: Gabor Varga <vargagab@gmail.com>
[merged definitions into appropriate block, extended commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Current OpenWrt MAC setup:
eth0 &rom 0xf100 :48
eth0.2 eth0+1 :49
wlan0 (5 GHz) &radio 0x8004 different OUI
wlan1 (2.4 GHz) &radio 0x4 same OUI as wlan0
Label MAC address corresponds to eth0 (ðernet).
No additional addresses found in hexdump of rom/radio.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Enabling legacy PTYs causes problems with procd-hotplug.
And as this is a headless target, no need to have virtual terminals.
Remove corresponding kernel config options, they are disabled in
generic kernel config.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enabling legacy PTYs causes problems with procd-hotplug.
And as this is a headless target, no need to have virtual terminals.
Remove corresponding kernel config options, they are disabled in
generic kernel config.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The "/dts-v1/;" identifier is supposed to be put once at the beginning
of a device tree file. Thus, it makes no sense to provide it a second
time in to-be-included DTSI files.
This removes the identifier from all DTSI files in /target/linux.
Most of the DTS files in OpenWrt do contain the "/dts-v1/;". It is
missing for most of the following targets, though:
mvebu, ipq806x, mpc85xx, ipq40xx
This does not touch ipq806x for now, as the bump to 4.19 is close.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Netgear WNR3500L is an already supported device, but out of the
box, the device has no switch configuration and there is no wan.
The correct configuration for this specific model is similar to
some other models. This simple commit adds the correct switch
and the out-of-the-box experience is improved.
Experimentally determined:
Port 0 => WAN
Port 1..4 => LAN
Port 5..7 => unused
Port 8 => CPU
Signed-off-by: Olli Asikainen <olli.asikainen@gmail.com>
Tested-by: Fabian Zaremba <fabian@youremail.eu>
[added port mapping to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
A small subset of devices uses decimal notation for mediatek,mtd-eeprom
in DTS files. Convert to hexadecimal notation to be consistent with
all the rest.
Also change "0" to "0x0" in the same files for consistency.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Mikrotik RBM33G has only 2 LAN ports.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
[moved node in 02_network to maintain alphabetic sorting]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Physical port order watched from the backside of the C20i
(from left to right) is: Internet / 1 / 2 / 3 / 4
Physical Port Switch port
WAN 0
LAN 3 1
LAN 4 2
LAN 1 3
LAN 2 4
(not used) 5
CPU 6
Signed-off-by: Walter Sonius <walterav1984@gmail.com>
[commit message/title improvements]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
"[...] the size component shall be zero."
(See "PCI Bus Binding to: IEEE Std 1275-1994 Rev 2.1"
section "4.1.1 Open Firmware-defined Properties for Child Nodes")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Hardware:
* SoC: Atheros AR9342-BL1A
* RAM: 64MB DDR2 (Winbond W9751G6KB-25)
* Flash: 16MB SPI NOR (Macronix MX25L12835FZ2I-10G)
* Ethernet: 1x 10/100/1000 Mbps (Atheros AR8035-A) with 24V PoE support
* Wifi 2.4GHz: Atheros AR9340 v2
* WiFi 5GHz: Ubiquiti U-AME-G1-BR4A (rebranded QCA988X v2)
* LEDs: 1x Power, 1x Ethernet
* Buttons: 1x Reset
* UART: 1x TTL 115200n8, 3.3V RX TX GND, 3.3V pin closest to RJ45 port
The LEDs do not seem to be connected to any GPIO, so there is currently
no way to control them.
Installation via U-Boot, TFTP and serial console:
* Configure your TFTP server with IP 192.168.1.254
* Connect serial console and power up the device
* Hit any key to stop autoboot
* tftpboot 0x81000000 openwrt-ath79-generic-ubnt_litebeam-ac-gen2-initramfs-kernel.bin
* bootm 0x81000000
* copy openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin
to /tmp
* sysupgrade /tmp/openwrt-ath79-generic-ubnt_litebeam-ac-gen2-squashfs-sysupgrade.bin
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The sysupgrade image contains OpenWrt specific metadata. Having this
metadata in the factory images makes no sense. Drop IMAGE/factory.bin
from Device/ubnt-wa and use the default from Device/ubnt instead.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Petr Štetiar <ynezz@true.cz>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
It turns out my 4.14 testing had a rather large flaw in it and the
'extack' mechanism isn't quite ready. Remove the extack stuff from this
backport.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Since the original backports from kernel 5.3 a few things have been
tweaked by kernel bumps & other upstream changes. Update the backport
to reflect upstream as closely as possible and remove the bitrot.
Functions remain the same, error reporting improved.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
In d421a8b944 ("ath79: read label MAC address from flash instead
of using phy0/phy1") the source of the label MAC address was changed
for devices just reading it from phy0. To get rid of the dependency
from phy startup, addresses were read directly from the flash
locations that are used to initialize the phy MAC addresses.
Unfortunately, it turned out that Ubiquiti XM devices seem to have
different flash locations than expected, and also seem to have
specific locations for different devices (all in art/EEPROM):
0xe012 AR9280 Nanostation M2 - 0x120c
0xe035 AR9280 Nanostation M3 - 0x120c
0xe1b2 AR9280 Rocket M2 - 0x120c
0xe1c3 AR9280 Rocket M3 - 0x120c
0xe1b5 AR9280 Rocket M5 - 0x120c
0xe2d5 AR9280 Bullet M2 Titanium - 0x120c
0xe2b5 AR9280 Nanobridge M5 - 0x120c
0xe202 AR9280 Bullet M2 - 0x120c
0xe232 AR9287 Nanobridge M2 - 0x110c
0xe4a2 AR9285 AirRouter - 0xa0bf
Picostation M2 - 0x120c and 0xa0bf
Nanostation Loco M2 - not in 0x120c, other locations not checked
An additional problem of the Ubiquiti device support in OpenWrt is
that we provide images that match several subvariants of the devices,
which might have different MAC address locations.
Given that reading the address from phy0 in 02_network _is_ working
for the ath79 target in general, it does not seem reasonable to
rebuild a complex MAC address retrieval mechanism which is already
present in the ath9k driver.
So, this patch reverts the label MAC address source for Ubiquiti XM
devices (and the Unifi AP) to /sys/class/ieee80211/phy0/macaddress.
This doesn't affect XW and Unifi AC devices, where the label MAC
address source is defined via device tree.
For alfa-network,ap121f the location 0x1002 is kept, as this has
been verified during device support preparation in PR #2199.
Fixes: d421a8b944 ("ath79: read label MAC address from flash
instead of using phy0/phy1")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sysupgrade was failing due to incorrect replacement of backticks:
/sbin/sysupgrade: /lib/upgrade/platform.sh: line 101: syntax error: missing '))'
Fixes: 0bbfc3dff7 ("octeon: replace backticks by $(...)")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
The Atheros AR8327 and AR8337 have (according to their datasheet) a
VLAN table with a maximum of 4096 entries.
Currently, there's a hard limit of 128 VLANs, which is the same as
for most other Atheros switches. Increase this limit only for the
AR83x7 series and modify some shared functions to allow them to work
with a variable max VLAN count.
Signed-off-by: David Bauer <mail@david-bauer.net>
The Owl Loader (named after the codename that Atheros gave
these devices back in the day) has been accepted upstream.
This patch removes the "misc" driver OpenWrt had and adds
the remaining differences against the version that ships
with 5.4-rc1 into a separate "120-owl-loader-compat.patch"
file that can be cut down once AR71XX is being dealt with.
Note: I decided to keep the existing (kmod-)owl-loader
package name around for now. The kernel module file in
the kmod package will be called ath9k_pci_owl_loader.ko
though.
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
MeshPoint.One is Wi-Fi hotspot and smart IoT gateway (based upon
Jalapeno module from 8Devices).
MeshPoint.One (https://meshpointone.com) is a unique Wi-Fi hotspot and
smart city gateway that can be installed and powered from street
lighting (even solar power in the future). MeshPoint provides up to 27
hours of interrupted Wi-Fi and IoT services from internal battery even
when external power is not available. MeshPoint.One can be used for
disaster relief efforts in order to provide instant Wi-Fi coverage that
can be easily expanded by just adding more devices that create wide area
mesh network. MeshPoint.One devices have standard Luci UI for
management.
Features:
- 1x 1Gpbs WAN
- 1x 1Gbps LAN
- POE input (eth0)
- POE output (eth1)
- Sensor for temperature, humidity and pressure (Bosch BME280)
- current, voltage and power measurement via TI INA230
- Hardware real time clock
- optional power via Li-Ion battery
- micro USB port with USB to serial chip for easy OpenWrt terminal
access
- I2C header for connecting additional sensors
Installation:
-------------
Simply flash the sysupgrade image from stock firmware.
Or use the built in Web recovery into bootloader:
Hold Reset button for 5 to 20 seconds or use UART and httpd command.
Web UI will appear on 192.168.2.100 by default.
For web recovery use the factory.ubi image.
Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
Signed-off-by: Damir Franusic <damir.franusic@sartura.hr>
Signed-off-by: Valent Turkovic <valent@meshpoint.me>
Signed-off-by: Robert Marko <robert@meshpoint.me>
[commit description long line wrap, usb->USB]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Lets move common code for Jalapeno into DTSI, this way Jalapeno based
boards don't introduce duplicate code.
While at it, lets also fix some style issues and update to current DTS
style.
Signed-off-by: Robert Marko <robert@meshpoint.me>
[commit description long line wrap]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
By adding the vendor to the Makefile device definition node name,
one can derive the standard compatible used in SUPPORTED_DEVICES
instead of having to specify it manually.
Despite, this moves the naming scheme closer to what is used for
other targets (ath79, ramips).
Build-tested on all subtargets.
Run-tested on TP-Link TL-WDR4900 v1.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch is based on #1689 and adds support for TP-Link Archer
C6 v2 (US) and A6 (US/TW).
The hardware is the same as EU and RU variant, except for GPIOs
(LEDS/Buttons), flash(chip/partitions) and UART being available
on the board.
- SOC: Qualcomm QCA9563 @ 775MHz
- Flash: GigaDevice GD25Q127CS1G (16MiB)
- RAM: Zentel A3R1GE40JBF (128 MiB DDR2)
- Ethernet: Qualcomm QCA8337N: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless:
- 2.4GHz (bgn) QCA9563 integrated (3x3)
- 5GHz (ac) Qualcomm QCA9886 (2x2)
- Button: 1x power, 1x reset, 1x wps
- LED: 6x LEDs: power, wlan2g, wlan5g, lan, wan, wps
- UART: 115200, 8n1 (header available on board)
Known issues:
- Wireless: 5GHz is known to have lower RSSI signal, it affects speed and range.
Flash instructions:
Upload openwrt-ath79-generic-tplink_archer-c6-v2-us-squashfs-factory.bin
via the router Web interface.
Flash instruction using tftp recovery:
1. Connect the computer to one of the LAN ports of the router
2. Set the computer IP to 192.168.0.66
3. Start a tftp server with the OpenWrt factory image in the
tftp root directory renamed to ArcherA6v2_tp_recovery.bin.
4. Connect power cable to router, press and hold the
reset button and turn the router on
5. Keep the reset button pressed until the WPS LED lights up
6. Wait ~150 seconds to complete flashing
Flash partitioning: I've followed #1689 for defining the partition layout
for this patch. The partition named as "tplink" @ 0xfd0000 is marked
as read only as it is where some config for stock firmware are stored.
On stock firmware those stock partitions starts at 0xfd9400 however
I had not been able to make it functional starting on the same address as
on stock fw, so it has been partitioned following #1689 and not the stock
partition layout for this specific partition. Due to that firmware/rootfs
partition lenght is 0xf80000 and not 0xf89400 as stock.
According to the GPL code, the EU/RU/JP variant does have different GPIO pins
assignment to LEDs and buttons, also the flash memory layout is different.
GPL Source Code: https://static.tp-link.com/resources/gpl/gpl-A6v2_us.tar.gz
Signed-off-by: Anderson Vulczak <andi@andi.com.br>
[wrap commit message, remove soft_ver change for C6 v2 EU, move LED aliases
to DTS files, remove dts-v1 in DTSI, node/property reorder in DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This renames all remaining occurrences of "EEPROM" to "art" to
further harmonize the partition labelling in ath79. This will
help to reduce the amount of user-space code and might be
beneficial when code is copy/pasted in the future.
Affected are only devices from Ubiquiti, where the XM board is
already using "art" in ath79.
Acked-by: Piotr Dymacz <pepe2k@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
YunCore XD4200 ('XD4200_W6.0' marking on PCB) is Qualcomm/Atheros based
(QCA9563, QCA9886, QCA8334) dual-band, Wave-2 AC1200 ceiling AP with PoE
(802.3at) support. A782 model ('T750_V5.1' marking on PCB) is a smaller
version of the XD4200, with similar specification but lower TX power.
Specification:
- QCA9563 (775 MHz)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 2x 10/100/1000 Mbps Ethernet (QCA8334), with 802.3at PoE support (WAN)
- Wi-Fi 2.4 GHz:
- XD4200: 2T2R (QCA9563), with ext. PA (SKY65174-21) and LNA
- A782: 2T2R (QCA9563), with ext. FEM (SKY85329-11)
- Wi-Fi 5 GHz:
- XD4200: 2T2R (QCA9886), with ext. FEM (SKY85728-11)
- A782: 2T2R (QCA9886), with ext. FEM (SKY85735-11)
- LEDs:
- XD4200: 5x (2x driven by SOC, 1x driven by AC radio, 2x Ethernet)
- A782: 3x (1x RGB, driven by SOC and radio, 2x Ethernet)
- 1x button (reset)
- 1x UART (4-pin, 2.54 mm pitch) header on PCB
- 1x DC jack (12 V)
Flash instructions:
If your device comes with generic QSDK based firmware, you can login
over telnet (login: root, empty password, default IP: 192.168.188.253),
issue first (important!) 'fw_setenv' command and then perform regular
upgrade, using 'sysupgrade -n -F ...' (you can use 'wget' to download
image to the device, SSH server is not available):
fw_setenv bootcmd "bootm 0x9f050000 || bootm 0x9fe80000"
sysupgrade -n -F openwrt-...-yuncore_...-squashfs-sysupgrade.bin
In case your device runs firmware with YunCore custom GUI, you can use
U-Boot recovery mode:
1. Set a static IP 192.168.0.141/24 on PC and start TFTP server with
'tftp' image renamed to 'upgrade.bin'
2. Power the device with reset button pressed and release it after 5-7
seconds, recovery mode should start downloading image from server
(unfortunately, there is no visible indication that recovery got
enabled - in case of problems check TFTP server logs)
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
YunCore QCA9k based devices released in 2019 require a custom TFTP image
for U-Boot built-in recovery mode (triggered with reset button). Image
has to be prepended with 'YUNCORE' keyword followed by U-Boot CLI
commands which will be executed later. Images without the custom header
will be ignored by U-Boot.
To be able to support both the vendor firmware (QSDK) and OpenWrt flash
layouts, used here commands change the 'bootcmd' before flashing image.
This commit adds generic helper script for YunCore devices with 16 MB of
flash and enables TFTP image generation for A770 model.
Signed-off-by: Vincent Wiemann <vincent.wiemann@ironai.com>
[pepe2k@gmail.com: commit description reworded, recipe renamed]
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This re-organizes the device-tree files for the Sercomm-manufactured
NETGEAR routers. They are now split into two different base-boards,
from which the respective model is extended.
This partially reverts commit c7842ceaaa ("ramips: reorganize DTSI
files for Netgear R devices"), which introduced inheritance between two
completely unrelated base-boards.
Signed-off-by: David Bauer <mail@david-bauer.net>
