This change enables proper Ethernet link status and speed reporting on
the Ubiquiti UniFi 6 LR access point:
mtk_soc_eth 1b100000.ethernet eth0: PHY [mdio-bus:08] driver [Aquantia AQR112C] (irq=POLL)
mtk_soc_eth 1b100000.ethernet eth0: configuring for phy/2500base-x link mode
mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable Aquantia Ethernet PHY driver as there is an AQR112C 2500Base-T
PHY in the Ubiquiti UniFi 6 LR access point.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Based on: 1ac627024d ("kernel: ath10k-ct: provide a build variant for
small RAM devices")
Like described in the ath10k-ct-smallbuffers version, oom-killer gets
triggered frequently by devices with small RAM.
That change is necessary for many community mesh networks which use
ath10k based devices with too little RAM. The -ct driver has been
proven unstable if used with 11s meshing and only wave2 chipsets are
supporting 11s. Freifunk Berlin is nowadays assembling its
firmware-based completely of vanilla OpenWRT with some package additions
which are made through the imagebuilder. Therefore we cannot take the
approach other freifunk communities have taken to maintain that patch
downstream [1]. Other communities consider these devices as broken and
that change would pretty much give those devices a second life [2].
[1] - 450b306e54
[2] - https://github.com/freifunk-gluon/gluon/issues/1988#issuecomment-619532909
Signed-off-by: Simon Polack <spolack+git@mailbox.org>
Signed-off-by: Nick Hainke <vincent@systemli.org>
Fix default network configuration of the Puzzle-M902 so all LAN ports
are included in the LAN bridge.
Setup network LED to indicate WAN port link status, like vendor
firmware does as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixes Ethernet link status on all ports and makes 2.5G ports usable
in 2.5G and 1G full-duplex mode.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Copy and refresh patch enabling AQR112 and AQR412 Ethernet PHY from
layerscape (5.4) target to generic (5.10) as AQR112 can also be found
on other targets as well.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The auto-ht option already kept HT and VHT support, but wasn't updated
to support HE (11ax).
Signed-off-by: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Wire up MCU driver for LEDs, fan and temperature sensor, and add
GPIO reset button just like on the M902 also on the Puzzle M901.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Set blinking mode using scheduled work instead of blocking which may
result in deadlocks.
Add dynamic kprintf debugging hexdumps of all MCU rx and tx.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Kernel 5.10 is used by many people since quite a while. With other
targets already moved to 5.10, let ath79 follow suit.
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [ath79/tl-wdr3600; ath79/tl-wdr4300]
Tested-by: Aleksander Jan Bajkowski <olek2@wp.pl> [ath79/tl-wdr4300]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: David Bauer <mail@david-bauer.net>
This device is based on NXP's QorIQ T2081QDS board, with a quad-core
dual-threaded 1.5 GHz ppc64 CPU and 4GB ECC RAM. The board has 5
ethernet interfaces, of which 3 are connected to the ethernet ports on
the front panel. The other 2 are internally connected to a Marvell
88E6171 switch; the other 5 ports of this switch are also connected to
the ethernet ports on the front panel.
Installation: write the sdcard image to an SD card. Stock U-Boot will
not boot, wait for it to fail then run these commands:
setenv OpenWrt_fdt image-watchguard-firebox-m300.dtb
setenv OpenWrt_kernel watchguard_firebox-m300-kernel.bin
setenv wgBootSysA 'setenv bootargs root=/dev/mmcblk0p2 rw rootdelay=2 console=$consoledev,$baudrate fsl_dpaa_fman.fsl_fm_max_frm=1530; ext2load mmc 0:1 $fdtaddr $OpenWrt_fdt; ext2load mmc 0:1 $loadaddr $OpenWrt_kernel; bootm $loadaddr - $fdtaddr'
saveenv
reset
The default U-Boot boot entry will now boot OpenWrt from the SD card.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
Add a new target named "qoriq", that will support boards using PowerPC
processors from NXP's QorIQ brand.
This doesn't actually add support for any board yet, so that
installation instructions can go in the commit message of the commit
that adds actual support for a board.
Using CONFIG_E6500_CPU here due to the kernel using -mcpu=powerpc64
rather than -mcpu=e5500 when selecting CONFIG_E5500_CPU. The only
difference between e5500 and e6500 is AltiVec support, and the kernel
checks for it at runtime. Musl will only check at runtime if AltiVec
support is disabled at compile-time, so we need to use e5500 in CPU_TYPE
to avoid SIGILL.
Math emulation (CONFIG_MATH_EMULATION_HW_UNIMPLEMENTED) is required, as
neither e5500 nor e6500 implement fsqrt nor fsqrts, and musl hardcodes
sqrt and sqrtf to use these ASM instructions on PowerPC64.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
Backport an upstream patch to make libunwind build on ppc64, and add
powerpc64 to the dependencies.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
As of version 3.7, Nettle added PowerPC64 assembly for several
algorithms. Unfortunately, they cause build to fail due to ABI mismatch:
gcm-hash.o: ABI version 1 is not compatible with ABI version 2 output
Disable assembler when ppc64 and musl are used for now.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
Backport an upstream patch that adds support for ELFv2 ABI on big endian
ppc64. As musl only supports ELFv2 ABI on ppc64 regardless of
endianness, this is required to be able to build OpenSSL for ppc64be.
Modify our targets patch to add linux-powerpc64-openwrt, which will use
the linux64v2 perlasm scheme. This will probably break the combination
ppc64 with glibc, but as we really only want to support musl, this
shouldn't be a problem.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
At configuration time, gcc assumes that ppc64be targets use the ELFv1
ABI, and ppc64le targets use the ELFv2 ABI. However, musl libc does not
support the ELFv1 ABI on ppc64 at all, regardless of the endianness.
Therefore, when building for a ppc64 arch and with musl libc, instruct
gcc to use the ELFv2 ABI.
See https://gcc.gnu.org/bugzilla/show_bug.cgi?id=93157 for more info.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
This CPU type is compatible with NXP's PPC based QorIQ processors, and
will be used by the upcoming new qoriq target.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
Backport MFD driver for communicating with the on-board MCU found on
IEI World Puzzle appliances.
Improve the driver to support multiple LEDs, apply a default state and
let MCU take care of blinking if timing is within supported range.
Wire up LEDs and fan for Puzzle M902 in device tree.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Provide incoming BSS transition queries to ubus subscribers.
This allows external steering daemons to provide clients with
an optimal list of transition candidates.
This commit has no functional state in case no ubus subscriber is
present or it does not handle this ubus message.
To prevent hostapd from sending out a generic response by itself, a
subscribing daemon has to return a non-zero response code to hostapd.
Signed-off-by: David Bauer <mail@david-bauer.net>
Backport a patch to allow extending the ubus BSS-transition method
for specifying individual dialog tokens for BSS transition
management requests.
This is required for handling BSS transition queries in the future.
Signed-off-by: David Bauer <mail@david-bauer.net>
The UniFi 6 Lite has two MAC addresses for the 2.4 and 5GHz radio in
it's EEPROM partition.
On my unit these are
F4 92 BF A0 BB 6F
F6 92 BF A0 BB 6F
The problem with these is that mac80211 increases the first octet by
2, which leads to conflicting MAC addresses between radios.
Work around this problem for now by increasing the last octet by 1 on
the 5 GHz radio.
Ubiquiti increases the last octet by 2 for each subsequent VAP created
per radio. Ideally we should do the same, however this functionality is
currently lacking from mac80211.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add ethernet0 alias in device tree to make U-Boot inherit the Ethernet
mac address (set via environment variable 'ethaddr') down to Linux.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
39b584b Revert "dhcpv6: add a minimum valid lifetime for IA_PD updates"
c9578e1 dhcpv6: add support for null IA_PD valid lifetime
ca43ea3 dhcpv6: add a minimum valid lifetime for IA_PD updates
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
5ca5e0b netifd: allow disabling rule/rule6 config sections
8875960 interface-ip: add support for IPv6 prefix invalidation
e589c05 interface-ip: use metric when looking for a route
b54ffde main: fix hotplug script usage message
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
Each of
- CRYPTO_AEAD2
- CRYPTO_AEAD
- CRYPTO_GF128MUL
- CRYPTO_GHASH
- CRYPTO_HASH2
- CRYPTO_HASH
- CRYPTO_MANAGER2
- CRYPTO_MANAGER
- CRYPTO_NULL2
either directly required for mac80211 crypto support, or directly
selected by such options. Support for the mac80211 crypto was enabled in
the generic config since c7182123b9 ("kernel: make cryptoapi support
needed by mac80211 built-in"). So move the above options from the target
configs to the generic config to make it clear why do we need them.
CC: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Both CLANG_VERSION and LLD_VERISON are autogenerated runtime
configuration options, so add them to the kernel configuration filter
and remove from generic and per-target configs to keep configs clean.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
This patch has been upstream since GCC 10.
Dragan Mladjenovic (2):
Emit .note.GNU-stack for soft-float linux targets.
Emit .note.GNU-stack for hard-float linux targets.
Link: https://gcc.gnu.org/g:a3c1e1f2ff88
Link: https://gcc.gnu.org/g:54b3d52c3cca
Add backport patch to define TARGET_LIBC_GNUSTACK on musl to add
.note.GNU-stack on hard-float MIPS targets.
Link: https://gcc.gnu.org/g:25abbb924968
The net effect should be the exact same functionality while following
upstream code instead of a custom outdated patch.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800*
Run-tested: bcm2711/RPi4B, ipq806x/R7800*
*Had to revert 7f1edbd412 in order to build
(binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)
Signed-off-by: John Audia <graysky@archlinux.us>
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800*
Run-tested: bcm2711/RPi4B, ipq806x/R7800*
*Had to revert 7f1edbd412 in order to build
(binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)
Signed-off-by: John Audia <graysky@archlinux.us>
Removed target for patch which does not exist:
bcm27xx/patches-5.10/950-0249-kbuild-Disable-gcc-plugins.patch
All patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ipq806x/R7800*
Run-tested: bcm2711/RPi4B, ipq806x/R7800*
* Had to revert 7f1edbd412 in order to build
(binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149)
Signed-off-by: John Audia <graysky@archlinux.us>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*FS#4149 affects me so I had to revert 7f1edbd412
in order to downgrade to 2.35.1
Signed-off-by: John Audia <graysky@archlinux.us>
