This fixes the following compile warning:
CC init/do_mounts.o
init/do_mounts.c:478:19: warning: 'mount_ubi_rootfs' defined but not used [-Wunused-function]
478 | static int __init mount_ubi_rootfs(void)
| ^~~~~~~~~~~~~~~~
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The arc700 target is not booting up since some time, see here:
https://github.com/foss-for-synopsys-dwc-arc-processors/toolchain/issues/400
It looks like there is a problem in the toolchain when using glibc.
Currently no one is working on fixing this problem, remove the target
instead. This target also does not have many users we are aware of.
If someone wants to have this target back, feel free to add a fixed
version of this target again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Stijn Tintel <stijn@linux-ipv6.be>
I2C_CHARDEV used to be enabled in mt7621/config-5.4. Enable it in the
5.10 config, as it's required for PoE control on Unifi Switch Flex.
Fixes: b4aad29a1d ("ramips: add support for kernel 5.10")
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Flash accessing instruction templates are determined during probe since
v5.6 for spimem-dirmap support in spi-nor driver in upstream commit:
df5c21002cf4 ("mtd: spi-nor: use spi-mem dirmap API")
As a result, changing bus_width on the fly doesn't work anymore and this
patch will cause executing spi-mem ops with 3-byte address on 16-32M
flash area.
We can't easily revert that behavioral change upstream so drop the patch
to prevent u-boot and eeprom from being erased.
Fixes: b10d604459("kernel: add linux 5.10 support")
Reported-by: Frank Di Matteo <dimatto@foxmail.com>
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The NanoPi R4S leaves the SD card in 1.8V signalling when rebooting
while U-Boot requires the card to be in 3.3V mode.
Remove UHS support from the SD controller so the card remains in 3.3V
mode. This reduces transfer speeds but ensures a reboot whether from
userspace or following a kernel panic is always working.
Signed-off-by: David Bauer <mail@david-bauer.net>
The legacy image for the UniElec U7623-02 until now included
kmod-ata-ahci-mtk. The MT7623 chip doesn't have that IP and that
board uses a PCIe-connected AHCI controller for the SATA port and
mSATA-pins of the mPCIe socket. Hence include kmod-ata-ahci instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
For devboards without a MAC address assigned from factory, store
the random MAC in U-Boot env on first boot to make it persistent.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add U-Boot env settings to allow accessing the environment using
fw_printenv and fw_setenv tools on the UniElec U7623 board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Users of older OpenWrt versions need sysupgrade using the *emmc.img.gz
file once which will upgrade U-Boot and switch to the new image layout.
Users of the vendor firmware need to first flash the legacy image to
then sunsequently carry out a full-flash upgrade.
Alternatively the board can also be flashed using MediaTek's
proprietary SP Flash Tool.
Configuration as well as persistent MAC address will be lost once at
this point and you will have to redo (or restore) all configuration
manually. To restore the previous persistent MAC address users may set
it manually using
fw_setenv ethaddr 00:11:22:33:44:55
For future upgrades once running OpenWrt past this commit, the usual
*sysupgrade.itb file can be used.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* Use serial0 instead of serial2 for the only serial port
* Add LED aliases
* Add ethernet0 alias to inherit ethaddr from U-Boot env
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Enable 'rootfs-part' feature to make the size of the partition of the
production image configurable instead of hard-coding it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The GL.iNet GL-XE300 is a 4G LTE Wireless router, based on QCA9531 SoC.
Specifications:
- SoC: QCA9531 (650MHz)
- RAM: DDR2 128M
- Flash: SPI NOR 16M + SPI NAND 128M
- WiFi: 2.4GHz with 2 antennas
- Ethernet:
- 1x LAN (10/100M)
- 1x WAN (10/100M)
- LTE:
- USB: 1x USB 2.0 port
- UART:
- 3.3V, TX, RX, GND / 115200 8N1
MAC addresses as verified by OEM firmware:
use address source
LAN *:c5 art 0x0 (label)
WAN *:c6 label + 1
WLAN *:c7 art 0x1002
Installation via U-Boot rescue:
1. Press and hold reset and power buttons simultaneously
2. Wait for the LAN led to blink 5 times
3. Release reset and power buttons
4. The rescue page is accessible via http://192.168.1.1
5. Select the OpenWrt factory image and start upgrade
6. Wait for the router to flash new firmware and reboot
Revert to stock firmware:
i. Download the stock firmware from GL.Inet website
ii. Use the same method explained above to flash the stock firmware
Signed-off-by: Victorien Molle <victorien.molle@wifirst.fr>
[update commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
When Joowin WR758AC V1 and V2 devices were added, they should have been
added with the primary manufacturer name which is COMFAST, since Joowin
is just an alternate vendor name on some coutries or stores.
Fix this by changing the the vendor name on the respective files and set
Joowin as ALT0 variants while ensuring compatibility for early users.
Also adjust the model names to better follow the naming rules.
As a side effect, fix mt76x8 network script which was left incorrectly
unsorted on the case block conditions.
Fixes: 766733e172 ("ramips: add support for Joowin WR758AC V1 and V2")
Signed-off-by: Rodrigo Araujo <araujo.rm@gmail.com>
Currently the WAN MAC address is read from a different offset contrary
to all other addresses.
There's conflicting information whether offset 0x28 on the factory
partition contains the valid WAN mac for all devices while 0x4 seems to
be uniform.
Read the WAN mac from this location and calculate it.
Signed-off-by: David Bauer <mail@david-bauer.net>
The current MAC address assignment is still incorrect.
Use the same MAC address as seen on the stock firmware
for both wireless interfaces.
The 5GHz MAC address OUI is +2 in the first EUI octet. We currently
don't do this in OpenWrt. Ignore this offset for now. With the current
assignment, recurring MAC addresses between radios is already taken care
of.
Signed-off-by: David Bauer <mail@david-bauer.net>
This board has 512MiB of RAM like the R7800, and the VDSL modem is
attached to the second PCIe port.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
On MikroTik RB91x board series a reset key shares SoC gpio
line #15 with NAND ALE and NAND IO7. So we need a custom
gpio driver to manage this non-trivial connection schema.
Also rb91x-nand needs to have an ability to disable a polling
of the key while it works with NAND.
While we've been integrating rb91x-key into a firmware, we've
figured out that:
* In the gpio-latch driver we need to add a "cansleep" suffix to
several gpiolib calls,
* When gpio-latch and rb91x-nand fail to get a gpio and an error
is -EPROBE_DEFER, they shouldn't report about this, since this
actually is not an error and occurs when the gpio-latch probe
function is called before the rb91x-key probe.
We fix these related things here too.
Signed-off-by: Denis Kalashnikov <denis281089@gmail.com>
Reviewed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Tested by multiple users and since all targets need to be on Kernel 5.10
to be part of the next release, add changes.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Fix syntax error in the case statement
Fixes: 9149ed4f05 ("mvebu: cortexa9: Add support for Ctera C200-V2")
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Assign LED numbers properly by adding function-enumerator property in DTS.
While at it, remove default trigger of LAN LEDs as it will be handled in
01_leds anyway.
Fixes: 51b9aef553 ("ipq40xx: add support for ASUS RT-ACRH17/RT-AC42U")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
According to TI docs (Processor SDK Linux Getting Started Guide)
the Random Number Generator hardware is found on
OMAP16xx, OMAP2/3/4/5, AM33xx/AM43xx boards. It already
defined in device tree files. Let's enable it.
Some tests:
root@RTS1_OI:~# rngtest -c 1000 </dev/hwrng
rngtest 6.10
Copyright (c) 2004 by Henrique de Moraes Holschuh
This is free software; see the source for copying conditions.
There is NO warranty; not even for MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE.
rngtest: starting FIPS tests...
rngtest: bits received from input: 20000032
rngtest: FIPS 140-2 successes: 999
rngtest: FIPS 140-2 failures: 1
rngtest: FIPS 140-2(2001-10-10) Monobit: 0
rngtest: FIPS 140-2(2001-10-10) Poker: 0
rngtest: FIPS 140-2(2001-10-10) Runs: 1
rngtest: FIPS 140-2(2001-10-10) Long run: 0
rngtest: FIPS 140-2(2001-10-10) Continuous run: 0
rngtest: input channel speed: (min=198.710; avg=1265.501; max=2976.417)Kibits/s
rngtest: FIPS tests speed: (min=1.780; avg=37.085; max=39.736)Mibits/s
rngtest: Program run time: 15961329 microseconds
Signed-off-by: Alexey Smirnov <s.alexey@gmail.com>
After enhancing ltq-deu, build it by default for the devices
using it.
Reverts: 964863b ("ltq-deu: Mark lantiq DEU broken")
Signed-off-by: Daniel Kestrel <kestrel1974@t-online.de>
Since gzip-compressed kernel image stopped fitting on 4MB kernel
partition on the device, use lzma-loader wrapping LZMA-compressed
kernel. This yields bootable device once again, and saves a very
substantial amount of space, the kernel size decreasing from about 4.4MB
to about 2.5MB for 5.10 kernel. This avoids changing of the flash layout
for the device.
While at that, reactivate the build for the device.
Fixes: 5d8ea6d34f ("ath79: Deactivate ZyXEL NBG6716 by default")
Cc: André Valentin <avalentin@marcant.net>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Alex Henrie <alexhenrie24@gmail.com>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Device specifications:
======================
* Qualcomm/Atheros AR7240 rev 2
* 350/350/175 MHz (CPU/DDR/AHB)
* 32 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ 18-24V passive POE (mode B)
+ used as WAN interface
- eth1
+ builtin switch port 4
+ used as LAN interface
* 12-24V 1A DC
* external antenna
The device itself requires the mtdparts from the uboot arguments to
properly boot the flashed image and to support dual-boot (primary +
recovery image). Unfortunately, the name of the mtd device in mtdparts is
still using the legacy name "ar7240-nor0" which must be supplied using the
Linux-specfic DT parameter linux,mtd-name to overwrite the generic name
"spi0.0".
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
On ar71xx, it was possible to overwrite the name of the spi-nor mtd device
identifier using the flash_platform_data which each mach-*.c could adjust
for its devices. A similar feature was introduced for mtd-physmap in
devicetree's. The property linux,mtd-name can be used to set the name and
provide a stable identifier for mtdpart from the bootloader.
But this feature is not yet available upstream for spi-nor devices which
also might receive their partition layout from the bootloader. But the
OpenWrt pistachio support for this property can simply be imported into
ath79 to gain this support.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
======================
* Qualcomm/Atheros QCA9558 ver 1 rev 0
* 720/600/200 MHz (CPU/DDR/AHB)
* 128 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2T2R 2.4 GHz Wi-Fi (11n)
* 2T2R 5 GHz Wi-Fi (11ac)
* 4x GPIO-LEDs (3x wifi, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default))
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* TI tmp423 (package kmod-hwmon-tmp421) for temperature monitoring
* 2x ethernet
- eth0
+ AR8035 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 802.3af POE
+ used as LAN interface
- eth1
+ AR8031 ethernet PHY (RGMII)
+ 10/100/1000 Mbps Ethernet
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
This device support is based on the partially working stub from commit
53c474abbd ("ath79: add new OF only target for QCA MIPS silicon").
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
This patch includes a series of performance improvements. All patches
were accepted and should land in 5.17.
NAT Performance results on BT Home Hub 5A (kernel 5.10.89, mtu 1500):
Down Up
Before 539 Mbps 599 Mbps
After 624 Mbps 695 Mbps
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
xrx200 max MTU is reduced so that it works correctly when set to the
max, and the max MTU of the switch is increased to match.
In 5.10, the switch driver now enables non-standard MTUs on a per-port
basis, with the overall frame size set based on the cpu port. When the
MTU is not used, this should have no effect. The maximum packet size is
limited as large packets cause the switch to lock up.
0702-net-lantiq-add-support-for-jumbo-frames.patch comes from net-next
commit 998ac358019e491217e752bc6dcbb3afb2a6fa3e.
In 5.4, all switch ports are configured to accept the max MTU, as 5.4
does not have port_max_mtu/port_change_mtu callbacks.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
Chen Minqiang reported on github:
| DTC arch/arm/boot/dts/qcom-ipq4029-ap-365.dtb
|qcom-ipq4019.dtsi:520.23-560.5: ERROR (phandle_references): /soc/wifi@a000000:
|Reference to non-existent node or label "macaddr_mfginfo_1d"
|
| also defined at qcom-ipq4029-aruba-glenmorangie.dtsi:243.8-248.3
|qcom-ipq4019.dtsi:562.23-602.5: ERROR (phandle_references): /soc/wifi@a800000:
|Reference to non-existent node or label "macaddr_mfginfo_1d"
|
| also defined at qcom-ipq4029-aruba-glenmorangie.dtsi:250.8-256.3
|ERROR: Input tree has errors, aborting (use -f to force output)
|scripts/Makefile.lib:326: recipe for target 'qcom-ipq4029-ap-365.dtb' failed
Fixes: cfc13c4459 ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data")
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It was reported the caldata on the FritzBox 7430 is not only stored at
different offsets, but is also larger than the current output size
limit.
Increase the output file size limit (after deflate) by 1024 bytes.
Ref: FS#3604 ("ath9k firmware is 0 bytes on Fritzbox 7430")
Signed-off-by: David Bauer <mail@david-bauer.net>
- clean up leftovers regarding MAC configure in dts
- fix alphabetical order in caldata
- IMAGE_SIZE for sysupgrade image
Signed-off-by: Tamas Balogh <tamasbalogh@hotmail.com>
Move config options
CONFIG_PHY_MVEBU_A38X_COMPHY
CONFIG_RTC_DRV_MV
to cortexa9/config-5.10.
These are not needed for arm64 targets.
Signed-off-by: Marek Behún <kabel@kernel.org>
This option includes support for watchdog timer on Marvell Armada 37xx
SoCs. [1] It is useful e.g. for Turris MOX, Marvell ESPRESSObin
Enable armada-37xx-watchdog driver as built in for mvebu cortex-a53,
so that kernel can start serving as soon as the driver is probed, until userspace takes over it.
[1] https://cateee.net/lkddb/web-lkddb/ARMADA_37XX_WATCHDOG.html
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(improved commit message, 2nd paragraph)
Signed-off-by: Marek Behún <kabel@kernel.org>
Enabling Armada 37xx rWTM driver. This gives the kernel access to random
number generator, if provided by the rWTM firmware.
Note that the driver is called turris-mox-rwtm because it was initially
written for Turris MOX, but will also work on other Armada 37xx
platforms, if they use rWTM firmware from CZ.NIC [1].
It makes sense to have this driver built-in, so that kernel has access
to random number generator without needing to load any drivers.
[1] https://gitlab.nic.cz/turris/mox-boot-builder
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andre Heider <a.heider@gmail.com>
Backport 2 patches for Armada 3720 comphy from 5.15 kernel.
These are needed for clear application of pending patches that fix this
driver.
Signed-off-by: Marek Behún <kabel@kernel.org>
Backport Aardvark PCIe controller driver changes that fix MSI support,
that were recently sent to the linux-pci mailing list [1].
These changes fix MSI and MSI-X support for this PCIe controller, which,
among other things, make it possible to use NVMe drives with this PCIe
controllers.
[1] https://lore.kernel.org/linux-pci/20220110015018.26359-1-kabel@kernel.org/
Signed-off-by: Marek Behún <kabel@kernel.org>
