Devices with wifi (LicheePi RV and MangoPi MQ Pro) were using the
wrong module. Also wpad was missing to enable using the WiFi.
Signed-off-by: Raylynn Knight <rayknight@me.com>
Link: https://github.com/openwrt/openwrt/pull/17576
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Teltonika RUTX50 mac-addresses on its wired interfaces are currently
random on every boot.
Setting the mac-addresses from device-tree using nvmem does not work, as
the vendor bootloader mangles the mtd partitions, removing the
nvmem-cells property.
To remedy the random mac-addresse, set the correct ones in preinit.
Signed-off-by: David Bauer <mail@david-bauer.net>
Turn on the 5G modem of the RUTX50 on by default.
This allows to make the modem detectable on a fresh
installation OOTB without further intervention.
Signed-off-by: David Bauer <mail@david-bauer.net>
Without this patch, we get the following error:
Mon Dec 23 11:35:44 2024 daemon.err hostapd: nl80211: kernel reports: integer out of range
As updating hostapd would be too complex and requires further testing,
we backport this simple upstream fix instead.
Fixes: https://github.com/openwrt/openwrt/issues/16680
Signed-off-by: Rany Hany <rany_hany@riseup.net>
Link: https://github.com/openwrt/openwrt/pull/17590
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Define RUT240 as alternative name, to explicitly show the device is
supported using existing image.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17503
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Newer modems used in RUT240 (Quectel EC25 and MeiG SLM750) use the
"option" driver instead of CDC-ACM. Include it in the image too.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17503
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Remove GPIO hog for modem power, as well as define userspace GPIO
switches for enabling and resetting the modem. While at that, define a
switch for the external GPIO available on the power connector.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17503
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
USB VBUS regulator was attached to GPIO19, which isn't in fact
controlling the modem power itself, but rather modem power key - which
has to be asserted high for at least 500ms, to start the modem. Keeping
it high allows the modem to reboot upon shutdown - so it is desirable to
control this line from userspace, for example - to allow clean modem
shutdown down upon powering off the router part.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17503
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Teltonika RUT240 has an extra 4G status LED on GPIO21. Otherwise the
hardware is fully compatible with RUT230 line. Attach the LED inside
device tree.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17503
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Due to "SIM present" input defaulting to "button" type, it is
interpreted as such when booting, and causes the system to enter
failsafe, if the tray is missing. Similarly to rfkill switch on
TP-Link WDR4300 and Archer C7, make it EV_SW instead, to stop it from
interfering with the boot process.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17503
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
It's missing a hyphen present in every other LED from the set. Set it to
"green:signal-strength-4".
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17503
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Settings for phy6 can be simplified in the DTS
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17430
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update to latest version. There are no patches that need to be
refreshed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17539
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update to latest version. There are no patches that need to be
refreshed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/17538
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
SoC: MediaTek MT7628AN
RAM: 128 MB, ESMT M14D1G1664A (DDR2)
Flash: 32MB, Winbond 25Q256JVFQ (Dual Boot, SPI)
Switch: MediaTek MT7628AN, 5 ports 100 Mbps
WiFi: MediaTek MT7603 2T2R/2.4GHz 802.11n and MediaTek MT7613AEN 2T2R/5GHz 802.11ac
USB: 1 port USB 2.0
GPIO: 3 buttons (Wi-Fi, Reset, FN), 4 LEDs (Power, Internet, FN, Wi-Fi), USB port power controls
Disassembly:
At the bottom there are 4 screws hidden by rubber feet. After removing the screws, pry the gray plastic part around (it is secured with latches) and remove it.
Serial Interface:
The serial interface can be connected to the 4 pin dots to the left of the flash.
Pins (from LEDs to LAN ports):
3.3V (do not connect)
TX
RX
GND
Settings: 115200, 8N1
Flashing via OEM recovery software:
1. Download the OEM recovery software from the manufacturer's website
2. Download the firmware image (for OpenWRT it is *-squashfs-factory.bin), rename it to KN-1711_recovery.bin
3. Replace the file in the fw folder OEM recovery software with the file from step 2.
4. Run the OEM recovery software and follow the instructions.
Flashing via TFTP:
1. Connect your PC and router to port 1-4, configure PC interface using IP 192.168.1.2, mask 255.255.255.252
2. Serve the firmware image (for OpenWRT it is *-squashfs-factory.bin) renamed to KN-1711_recovery.bin via TFTP
3. Power up the router while pressing Reset button on the back
4. Release Restart button when Power LED starts blinking
To revert back to OEM firmware:
The return to the OEM firmware is carried out by using the methods described above with the help of the appropriate firmware image.
When using OEM bootloader, the firmware image size cannot exceed the size of one OEM «Firmware_x» partition or Kernel + rootFS size.
Signed-off-by: Anton Yu. Ivanusev <ivanusevanton@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/17519
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The only real user of this patch was removed and migrated to the
upstream friendly regulator. Remove this hack.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17356
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, an OpenWrt hack is used to turn the GPIO on in terms of the
PHY driver when it should be the USB driver that controls it. The
chipidea USB2 driver has support for a vbus-supply property. Use it
instead of the local OpenWrt solution that just turns on the GPIO.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17356
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The chipidea USB2 driver used on this platform supports controlling GPIO
through regulators. This is the upstream friendly solution.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17356
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Subtarget xrx200_legacy supports only a few devices. They all use
the integrated Lantiq GSWIP switch and lantiq xway PHYs. The atheros
and icplus PHYs can be safely disabled.
Switches used by individual devices are listed below.
Device Switch PHY
Alpha ASL56026 Lantiq GSWIP int. switch
Arcadyan VG3503J Lantiq GSWIP int. switch
Netgear DM200 Lantiq GSWIP int. switch
TP-LINK TD-W8970 Lantiq GSWIP Lantiq PEF7071V
TP-Link TD-W8980 Lantiq GSWIP Lantiq PEF7071V
Reduces uncompressed kernel size by 16 kB.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17581
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This was done by executing these command:
$ make kernel_oldconfig CONFIG_TARGET=subtarget
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17581
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Plusnet Hub One and BT Business Hub 5A have the same hardware as
the BT Home Hub 5A. This commit adds alternative names so that both
devices can be easily found in the firmware selector.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17583
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The TP-Link TD-W9980(B) shares the same hardware with the TP-Link TD-W8980.
The only difference is that the TD-W8980 does not support VDSL. This is a
software limitation and once the software is changed, both work equally
supporting VDSL. This commit adds alternative names for devices so they
can be easily found in the firmware selector.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://github.com/openwrt/openwrt/pull/17583
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
A new syntax for LEDs was used, and migration of the LEDs configuration was
added. Used lower case hex characters for the addresses. Fixed a USB port
power issue.
Signed-off-by: Anton Yu. Ivanusev <ivanusevanton@yandex.ru>
Link: https://github.com/openwrt/openwrt/pull/17521
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Update the base DTS file for the 16 and 24 port HPE 1920 devices
(JG923A, JG924A, JG925A, JG926A), causing the new RTL8231 MFD driver to
be loaded at start-up.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Update the base DTS file for the 8 port HPE 1920 devices (JG920A,
JG921A, JG922A), causing the new RTL8231 MFD driver to be loaded at
start-up.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The manufacturer Cudy usually releases signed openwrt firmware, to
facilitate the migration from the proprietary version to the official
versions of openwrt. In contact with the manufacturer tells me that only
releases the firmware of the WR3000H if and only if
there is an official version. With this proposal I pretend to have an
initial operative version so that they do their part, and facilitate to
the users the possibility of using openwrt. In the present state, it is
only possible to use this firmware by uploading and installing it with
UART connection.
AX3000 2.5G Dual Band Wi-Fi 6 Mesh Router (WR3000H)
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
128MB SPI-NAND (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
4 LAN MediaTek MT7531 PHY
1 WAN RTL8221B-VB-CG 2.5Gbps PHY (C22)
2 Radios MT7976CN
UART: 115200 8N1 3.3V
MAC:
LAN MAC: label mac
WAN MAC: label mac + 1
2.4G MAC: label mac
5G MAC: label mac + 1 with LA bit set
Installation
------------
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device + press reset pin. Keep pressing reset pin to
enter the U-Boot shell (The recovery.bin image load process must fail).
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.88. Rename the image to "cudy3000h.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000h.bin; bootm 0x46000000
5. IMPORTANT: Make backup from original firmware. System -> Backup
/Flash Firmware -> Save mtdblock contents. All mtdblock one by one,
keep unaltered (BL2, u-boot-env, Factory, bdinfo, FIP, and ubi).
6. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Warning for BL2 and U-BOOT developers
-------------------------------------
The nand partition layout from vendor is slightly diferent from "standard".
The FIP partition starts at 0x3c0000 be carefull with BL2 to BL31.
The UBI partition start at 0x5c0000 be carefull.
DO NOT OVERWRITE bdinfo partition it contains hardware MAC definition
Layout is start-end (not start size)
- 0x000000000000-0x000007800000 : "nmbm0"
- 0x000000000000-0x000000100000 : "bl2"
- 0x000000100000-0x000000180000 : "u-boot-env"
- 0x000000180000-0x000000380000 : "factory"
- 0x000000380000-0x0000003c0000 : "bdinfo"
- 0x0000003c0000-0x0000005c0000 : "fip"
- 0x0000005c0000-0x0000045c0000 : "ubi"
ALLWAYS for U-BOOT operations check this
setenv mtdids nmbm0=nmbm0
setenv mtdparts nmbm0:1024k(bl2),512k(u-boot-env),2048k(factory),256k(bdinfo),2048k(fip),65536k(ubi)
Signed-off-by: Juan Pedro Paredes Caballero <juanpedro.paredes@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17458
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
TP-Link EAP610-Outdoor is a 802.11ax AP claiming AX1800 support. It is
wall or pole mountable, and rated for outdoor use. It can only be
powered via PoE.
Specifications:
---------------
* CPU: Qualcomm IPQ6018 Quad core Cortex-A53
* RAM: 512 MB
* Storage: ESMT PSR1GA30DT 128MB NAND
* Ethernet:
* Gigabit RJ45 port with PoE input
* WLAN:
* 2.4GHz/5GHz
* LEDs:
* Multi-color System LED (Green/Amber)
* Buttons:
* 1x Reset
* UART: 4-pin unpopulated header
* 1.8 V level, Pinout 1 - TX, 2 - RX, 3 - GND, 4 - 1.8V
Installation:
=============
Web UI method
-------------
Set up the device using the vendor's web UI. After that go to
Management->SSH and enable the "SSH Login" checkbox. Select "Save".
The connect to the machine via SSH:
ssh -o hostkeyalgorithms=ssh-rsa <ip_of_device>
Disable signature verification:
cliclientd stopcs
Rename the "-web-ui-factory" image to something less than 63
characters, maintaining the ".bin" suffix.
* Go to System -> Firmware Update.
* Under "New Firmware File", click "Browse" and select the image
* Select "Update" and confirm by clicking "OK".
If the update fails, the web UI should show an error message.
Otherwise, the device should reboot into OpenWRT.
TFTP method
-----------
To flash via tftp, first place the initramfs image on the TFTP server.
setenv serverip <ip of tftp server>
setenv ipaddr <ip in same subnet as tftp server>
tftpboot tplink_eap610-outdoor-initramfs-uImage.itb
bootm
This should boot OpenWRT. Once booted, flash the sysupgrade.bin image
using either luci or the commandline.
The tplink2022 image format
============================
The vendor images of this device are packaged in a format that does
not match any previous tplink formats. In order for flashing to work
from the vendor's web UI, firmware updates need to be packaged in
this format. The `tplink-mkimage-2022.py` is provided for this
purpose.
This script can also analyze vendor images, and extract the required
"support" string. This string is checked by the vendor firmware, and
images with a missing or incorrect string are rejected.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/14922
Signed-off-by: Robert Marko <robimarko@gmail.com>
This setting is more suitable for device running OpenWRT.
Most OpenWRT targets are already default to this configuration,
and it has shown better performance in VPN (wireguard).
Fix: #17454
Signed-off-by: Kien Truong <duckientruong@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17575
Signed-off-by: Robert Marko <robimarko@gmail.com>
OpenWRT on the WNDAP6x0 refuses to sysupgrade to itself
due to a compat_version imbalance. The Image is generated
with version 2.0, but the uci-defaults says that it needs
to be at 3.0 for the device.
Fix this by downgrading WNDAP6x0 05_fix-compat-version's
values back to 2.0 so it matches what we use.
Fixes: 5815884c3a2a ("apm821xx: migrate to DSA")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This was the first DSA packaged, and the tagger was made into
a separate package. This is too complicated: the mv88e6xxx
is the only module using this tagger after all, fold the module
for the DSA hardware and the driver for the tagger into a
single package and let modprobe do its job of probing the
tagger for the driver.
Tested on the BMIPS Inteno XG6846.
Link: https://patchwork.ozlabs.org/project/openwrt/patch/20250110-mv88e6xxx-single-package-v1-1-223ad7fb312e@linaro.org/
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a new port for the above device.
Currently, there is no easy installation method except
opening the device up and soldering a UART header on and
getting u-boot shell access. You boot the initramfs version
first using tftpboot, then once booted, you sysupgrade.
Shell access to root on vendor firmware:
admin:1234
To get U-Boot console, spam '4' into the serial console at boot.
with LEDs on the left, serial pinout is:
o - tx
o - rx
o - gnd
x - 3v3
server ip for tftpboot
192.168.0.225
The initramfs-kernel version boots without touching onboard flash with:
MT7628# tftpboot 0x80000000 openwrt-ramips-mt76x8-tplink_archer-mr200-v6-initramfs-kernel.bin
MT7628# bootm 0x80000000
Then when it boots off RAM, you copy
openwrt-ramips-mt76x8-tplink_archer-mr200-v6-squashfs-sysupgrade.bin
to /tmp/sysupgrade.bin of the device and run:
root@OpenWrt:/tmp# sysupgrade -n sysupgrade.bin
- [x] LEDs working
- [x] Buttons working
- [x] wlan detected
- [x] wwan detected
- [x] initramfs image working
- [x] sysupgrade working
Signed-off-by: Damien Zammit <damien@zamaudio.com>
Link: https://github.com/openwrt/openwrt/pull/15610
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Refresh DTS with required changes for cpufreq, MTD and MMC. While at it
also fix wrong speed for MAC.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Add patch fixing support for MMC. Additional clock are needed for MMC to
work and some small fixup to make the Mediatek MMC driver on Airoha SoC.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
