Drop config+patches for kernel 6.1.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15721
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Switch the apm821xx targets to kernel 6.6.
no complains received.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15721
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
gpio is deprecated. Found with dtc's -Wdeprecated_gpio_property
Used git grep -E $'\tgpio = <' to make the changes.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15681
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Use ath11k_patch_mac and ath11k_set_macflag functions for SXK80
Signed-off-by: Andrew Smith <gul.code@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/15732
Signed-off-by: Robert Marko <robimarko@gmail.com>
Move nvmem-cells definitions to dts files for compatibility with other files
in which mt7628an_tplink_8m.dtsi is loaded, to prevent overwriting
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Partially revert commit 98ddfbc56a ("generic: 6.6: backport upstream
commits for mtk_eth_soc") as the commit breaks WED. A better solution to
assign PPE units in case of WED has still to be found.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow a wider audience to test this pending series.
Use about to be submitted v3 which factors out block notification support.
Apart from dropping the no longer needed (and problematic) fallback for
for the 'partitions' node being present at the device parent there are
no intended functional changes.
As opening a block device as file is not supported yet in Kernel v6.6,
use the previous method as backporting seems a bit too involving.
Fixes: #15642
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The WS-AP3710i does not correctly expose its label-mac on eth0 anymore
since the change to simpleLoader.
Fix this by obtaining the label-mac from the U-Boot environment.
Signed-off-by: David Bauer <mail@david-bauer.net>
With the introduction of the simpleImage loader, the MAC address is not
set by the bootloader anymore.
Fix this by reading the MAC address from the U-Boot environment
partition.
Signed-off-by: David Bauer <mail@david-bauer.net>
We haven't received any bug reports in the past few weeks. So it's
time to set kernel 6.6 as the default and remove kernel 6.1 support.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The broadcom-wl driver was removed from OpenWrt, remove also the
profiles using it.
Fixes: e772b75d5d ("broadcom-wl: remove package")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The braodcom-wl driver was removed from OpenWrt, remove the special
exports it needed.
Fixes: e772b75d5d ("broadcom-wl: remove package")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This file is executable:
target/linux/ramips/dts/mt7621_dlink_dir-2150-a1.dts
Has to be fixed.
Fixes: 30e8fd73ec ("ramips: Add support for D-Link DIR-2150-A1")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
This commit fixes random lan mac for sercomm dxx devices.
Fixes: 3395184825 ("ramips: mt7621: nix mac-address-increment")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
0db4f9785c changed the variable name from
athaddr to ethaddr. Restore.
Fixes: 0db4f9785c ("ath79: convert ath10k calibration data to NVMEM (ASCII MAC)")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This router has two rootfs partitions and dualboot is used.
Vendor firmware may swap the rootfs partition location, u-boot append
'ubi.mtd=rootfs' in the end of cmdline. Since we use fixed-partitions,
force boot from the first rootfs partition to avoid boot failure.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15700
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport an upstream Linux fix to prevent BPF kfunc functions from being
removed during linker optimization when building BTF-enabled vmlinux.
The telltale sign of this occurring is build log warnings (e.g. mips64el):
BTFIDS vmlinux
WARN: resolve_btfids: unresolved symbol bpf_verify_pkcs7_signature
WARN: resolve_btfids: unresolved symbol bpf_lookup_user_key
WARN: resolve_btfids: unresolved symbol bpf_lookup_system_key
WARN: resolve_btfids: unresolved symbol bpf_key_put
WARN: resolve_btfids: unresolved symbol bpf_iter_task_next
WARN: resolve_btfids: unresolved symbol bpf_iter_css_task_new
WARN: resolve_btfids: unresolved symbol bpf_get_file_xattr
WARN: resolve_btfids: unresolved symbol bpf_ct_insert_entry
NM System.map
SORTTAB vmlinux
Link: https://lore.kernel.org/bpf/ZlkoM6%2FPSxVcGM6X@kodidev-ubuntu/
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15697
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The wifi radios on wax620 and wax630 got a random mac
address on boot. So fix this by using ath11k_patch_mac
and give a static mac address from label-mac-device.
Tested and working on wax620 and wax630.
Signed-off-by: Kristian Skramstad <kristian+github@83.no>
Link: https://github.com/openwrt/openwrt/pull/15597
Signed-off-by: Robert Marko <robimarko@gmail.com>
octeontx is currently stuck on kernel 5.15 since using 6.1 breaks booting,
and unfortunately nobody has stepped up to fix this issue.
Gateworks who were primary users have supported the removal.
Link: https://github.com/openwrt/openwrt/pull/15686
Signed-off-by: Robert Marko <robimarko@gmail.com>
The bump to kernel 6.6 increased the GPIO base from
412 to 512 on this target.
We need to compensate for that in the GPIO numbers being passed
to uci to fix following kernel report:
[ 24.176183] export_store: invalid GPIO 423
Tested on a Wallys DR40x9 board.
Please note that:
Boards "rtl30vw" and "wpj428" are not being altered here.
They define GPIO numbers which are even below the previous
base of 412 which looks wrong.
Actual testing on these boards should be conducted to validate
and optionally fix GPIO numbering.
Suggested-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
The WLR-1240 (ZX-5434) is an AC1200 Wave 2 outdoor repeater
with omnidirectional antennas for wall or pole mounting.
The device is manufactured by Todaair and meant to be used with
a tuya-based app, there is no webinterface for configuration.
Specifications:
- MT7628AN, 8 MiB SPI NOR flash, 64 MiB RAM, 2x2 802.11n
- MT7613 2x2 802.11ac Wave 2
- 802.3af PoE or 12V 1A 5.5x2.1 power supply (included)
- top RGB LED ring
TFTP installation:
- rename sysupgrade to `firmware_auto.bin`
- provide at 192.168.1.10 during boot
HTTP installation:
- keep reset button pressed for 5 seconds during power on (light blue
LED flashes slowly, then quickly to confirm, then remains steady on)
- recovery web interface is at 192.168.1.1, upload sysupgrade
Opening the device
- use suction cup to remove top cap within LED ring
- two screws are located in holes underneath silicone sealant
- two further screws are located at the bottom
initramfs boot
- open device, connect serial console (pins are labelled)
- keep pressing `4` during second tftp attempt to enter uboot shell
- run `tftpboot 82000000` to avoid memory overlap, then `bootm`
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
The WLR-1230 (ZX-5207) is an AC1200 Wave 2 outdoor repeater
with sector antennas for wall or pole mounting.
The device is manufactured by Todaair and meant to be used with
a tuya-based app, there is no webinterface for configuration.
Specifications:
- MT7628AN, 8 MiB SPI NOR flash, 64 MiB RAM, 2x2 802.11n
- MT7613 2x2 802.11ac Wave 2
- 802.3af PoE or 12V 1A 5.5x2.1 power supply (included)
- 3 LEDs WLAN, LAN, RES; PWR LED is not software-controllable
TFTP installation:
- rename sysupgrade to `firmware_auto.bin`
- provide at 192.168.1.10 during boot
HTTP installation:
- keep reset button pressed for 5 seconds during power on (LEDs
flash slowly, then quickly to confirm, then remain steady on)
- recovery web interface is at 192.168.1.1, upload sysupgrade
Opening the device
- two screws are located in the bottom left and right corners
underneath the label, inner tray slides out easily
initramfs boot
- open device, connect serial console (pins are labelled)
- keep pressing `4` during second tftp attempt to enter uboot shell
- run `tftpboot 82000000` to avoid memory overlap, then `bootm`
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
Add the kmod-mt7915e wifi driver to the default packages for the Ruijie
RG-X60 Pro. kmod-mt7915e has to be added recently and was not done
before merging the support for Ruijie RG-X60 Pro.
Fixes: 3de3c2bdfa ("mediatek: add support for Ruijie RG-X60 Pro")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cudy assigns hardware versions to its devices on its website, and
the Cudy TR1200 router is now Cudy TR1200 v1.
OpenWrt currently uses both variants, and this commit removes
inconsistencies using only the new name.
Signed-off-by: Luis Mita <luis@luismita.com>
Switch to new nvmem binding.
Also fixes a issue that the MAC address assigned to lan/wan was reversed.
Tested-by: Yangyu Chen <cyy@cyyself.name>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
- SOC: MediaTek MT7981
- ram: 256MB DDR3
- FLASH: 16MB SPI-NOR
- Ethernet: 2x1Gb Lan 1x1Gb Wan
- WIFI: MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4/5)
- LEDs: 2xLan 1x Wan 1x WIFI 1xSTATUS
MAC table, same as stock firmware:
LAN: 80:3F:5D:xx:xx:x1 partition "hw" at 0x44e (ASCII)
WAN: 80:3F:5D:xx:xx:x2 partition "hw" at 0x460 (ASCII)
2G: 80:3F:5D:xx:xx:x3 partition "factory" at 0x4 (binary), on label
5G: 80:3F:5D:xx:xx:x3 Same as 2G
Installation Method 1: ssh
--------------------------
1. Connect PC to the lan port. Set the PC IP to 192.168.10.100 if
required.
2. Navigate to http://192.168.10.1/
3. Log into the Wavlink WebGUI. Default username/password is
admin/admin.
4. Use WebGUI to upgrade the firmware to
WAVLINK_WN586X3-A_M86X3A_V240113_WO-GDBYFM-modified.bin
downloaded from
https://github.com/themaverickdm/firmware-misc/tree/main/wavlink/wl-wn586x3
Warning: All settings will be lost!
5. Wait about 5 minutes, and after flashing is completed, log into
the router using (with admin123 as password):
ssh root@192.168.10.1
6. scp the openwrt image file onto the router, usually under /tmp
somewhere.
openwrt-mediatek-filogic-wavlink_wl-wn586x3-squashfs-sysupgrade.bin
7. Flash openwrt image file like so:
mtd write \
openwrt-mediatek-filogic-wavlink_wl-wn586x3-squashfs-sysupgrade.bin \
firmware
Warning: Previous firmware will be overwritten!
8. Wait about 5 minutes, and after the flashing is completed, set
the PC IP to 192.168.1.100 if required and log into the router
like so:
ssh root@192.168.1.1
Installation Method 2: u-boot
-----------------------------
1. Connect UART: TX-> 586X3 RX, RX-> 586X3 TX, GND-> 586 GND.
2. Connect PC to the wan (not lan!) port.
3. Setup the tftp server on PC, set IP to 192.168.10.100,
4. Power on the device. Select '2' to upgrade firmware in Uboot.
5. Input the image name and start to upgrade.
Uboot console log:
CPU: MediaTek MT7981
Model: mt7981-rfb
DRAM: 256 MiB
Core: 34 devices, 13 uclasses, devicetree: embed
Loading Environment from nowhere... OK
In: serial@11002000
Out: serial@11002000
Err: serial@11002000
Net:
Warning: ethernet@15100000 (eth0) using random MAC address -
02:47:fb:b2:53:2d
eth0: ethernet@15100000
UBOOT WN586X3A
gpio: pin 9 (gpio 9) value is 0
gpio: pin 10 (gpio 10) value is 0
gpio: pin 5 (gpio 5) value is 0
gpio: pin 12 (gpio 12) value is 0
gpio: pin 13 (gpio 13) value is 0
*** U-Boot Boot Menu ***
1. Startup system (Default)
2. Upgrade firmware
3. Upgrade ATF BL2
4. Upgrade ATF FIP
5. Upgrade single image
6. Load image
0. U-Boot console
Co-authored-by: R Maru <deviantmaru@gmail.com>
Signed-off-by: R Maru <deviantmaru@gmail.com>
Signed-off-by: Sijia Huang <engineer31@win-star.com>
Before the nvmem rework, this was already handled in dts with
mtd-cal-data instead of qca,no-eeprom. No need to duplicate. Also, the
800 size value seems nonsensical. 440 is the standard.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Userspace handling is deprecated.
Also fix a bug with userspace handling where the wrong calibration data
was being used for the PCI card. The dts was correct but userspace was
not.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
These symbols have already been removed from the upstream Linux source
code. They are automatically compared and removed by a kernel config
scanning script[1].
[1] https://github.com/openwrt/openwrt/pull/15324
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Make the OF-compatible zImage per-board selectable. This allows the
image to only be built with the wrapper if the target actually uses it.
This fixes build-failures for the mpc85xx-p2020 subtarget.
Fixes: 557c094f0579 ("mpc85xx: only build zImage on required targets")
Signed-off-by: David Bauer <mail@david-bauer.net>
Set the appropriate cpu_port value based on the use of realtek,extif0 to extif2
instead of the additional cpu_port parameter.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15033
Signed-off-by: Robert Marko <robimarko@gmail.com>
Set the appropriate cpu_port value based on the use of realtek,extif0 or realtek,extif1 parameter.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15033
Signed-off-by: Robert Marko <robimarko@gmail.com>
All NETGEAR EX6150v2 validate the rootfs for which OpenWrt places a
fakeheader at the position, where the bootloader expects it.
Some EX6150v2 bootloaders do however make a broken assumption about
where the rootfs starts. This is due to them calculating the rootfs
start not based upon the kernel-length but the string-offset of the
FIT-image.
We have to be compatible with both this broken as well as the valid
calculation. So we do relocate the FDT string section to a
block-boundary and enlarge the FIT image to end at this boundary +
BLOCKSIZE / 2. This way, both the broken as well as correct calculations
do expect the rootfs-header at the same position.
It is worth noting, that this is a rare edge-case in which only happens
if the image-length as well as the start of the string-section are not
placed in the same erase-block. This is an edge-case which happens very
rarely (thus it was not spotted prior).
Affected:
- U-Boot 2012.07 (Jun 16 2016 - 11:59:37)
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 8f9546f7b0a14f3afa813e39ed45c968ece24464)
The recently added D-Link DNS-320L and the Zyxel NSA310S
is missing an RTC module so let's give them the default
Marvell RTC at least.
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio is actually low active, fix it.
Fixes: 40e7fab9e4 ("mediatek: add Nokia EA0326GMP support")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/15651
Signed-off-by: Robert Marko <robimarko@gmail.com>
The IMX device-tree's for arm moved from arch/arm/boot/dts to
arch/arm/boot/dts/nxp/imx. Use that if using the 6.6 kernel.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
copy 6.1 patches to 6.6 and fixup:
- removed patches already upstream
- adapted pathnames of dts patches for new kernel
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Patch 733-01-net-ethernet-mtk_eth_soc-use-napi_build_skb.patch needs
a refresh as line numbers no longer match.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
For the first-time installation (mostly migrates from vendor firmware)
the ubiblock is not ready, but bootdev detection relies on it. This
means users must create ubiblock manually otherwise the sysupgrade
will not work.
Now a unique case is added for nand devices which use new fit format,
let's move to it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 128 MB SPI-NAND
RAM: 256MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, WPS/Mesh
Power: DC 12V 1A
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Download the configration utilities:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
These binaries are extraced from the factory firmware, which are
dynamically linked with aarch64 musl 1.1.24. To use them, you
must run them under the same runtime environment, otherwise the
binaries will not work properly!
3. Upload the configuration and utilities to a suitable environment.
4. Uncompress the utilities, move them to '/bin' and give them executable permisison:
tar -zxf openwrt-mediatek-mt7981-nokia-ea0326gmp-config-utils.tar.gz
mv mkconfig seama /bin
chmod +x /bin/mkconfig
chmod +x /bin/seama
5. Decrypt and uncompress the configuration:
Enter fakeroot if you are not login as root.
mkconfig -a de-enca -m EA0326GMP_3FE79221BAAA -i EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz -o backup.tar.gz
tar -zxf backup.tar.gz
6. Edit 'etc/config/dropbear', set 'enable' to '1'.
7. Edit 'etc/passwd', remove root password: 'root::1:0:99999:7:::'.
8. Repack the configuration:
tar -zcf backup.tar.gz etc/
mkconfig -a enca -m EA0326GMP_3FE79221BAAA -i backup.tar.gz -o EA0326GMP_3FE79221BAAA-xxxxxxxx-backup.tar.gz
9. Upload new configuration via web interface, now you can SSH to EA0326GMP.
A minimum configuration which enabled SSH access is also provided
to simplify the process:
https://firmware.download.immortalwrt.eu.org/cnsztl/mediatek/filogic/openwrt-mediatek-mt7981-nokia-ea0326gmp-enable-ssh.tar.gz
Flash instructions:
1. SSH to EA0326GMP, backup everything, especially 'Factory' part.
2. Write new BL2:
mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-preloader.bin BL2
3. Write new FIP:
mtd write openwrt-mediatek-filogic-nokia_ea0326gmp-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Prior to performing a PROGRAM LOAD RANDOM DATA operation, a WRITE
ENABLE (06h) command must be issued to change the contents of the
memory array. Following a WRITE ENABLE (06) command, **first a PROGRAM
LOAD (02h or 32h) command must be issued to reset the cache**, then
issue a PROGRAM LOAD RANDOM DATA (84h or 34h) command
This is dirty fix provided to use by MediaTek engineer Sky Huang which
may resolve the "OpenWrt Kiss of Death" issue we've been seeing on the
Linksys E8450 aka. Belkin RT3200. However, it means that everything has
to be re-written with that patch already applied, ie. we need to rebuild
the installer once it is part of snapshot builds to have any effect.
Users already on FIP-in-UBI layout are advised to re-write 'fip' UBI
volume and 'bl2' MTD partition manually once from within Linux after
this fix has been applied.
A similar fix will also be required for U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Buffalo WSR-2533DHPL2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based
on MediaTek MT7621A.
Specification:
- SoC : MediaTek MT7621AT
- RAM : DDR3 128 MiB (Winbond W631GG6MB12J)
- Flash : RAW-NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN : 2.4/5 GHz (2x MediaTek MT7615N)
- Ethernet : 10/100/1000 Mbps x4
- Switch : MediaTek MT7530 (SoC)
- LED/keys : 8x/6x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB (J4)
- arrangement : 3.3V, GND, TX, RX from triangle-mark
- settings : 57600n8
- Power : 12VDC 1.5A
Flash instruction using factory.bin image:
1. boot WSR-2533DHPL2 normally with "Router" mode
2. access to the WebI ("http://192.168.11.1/") on the device and open
firmware update page
("管理" -> "ファームウェア更新")
3. select the OpenWrt factory.bin image and click update ("更新実行")
button
Attention: do not use "factory-uboot.bin" image
4. Wait ~120 seconds to complete flashing
Flash instruction using initramfs image:
1. prepare the TFTP server with the initramfs image renamed to
"linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPL2
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPL2 downloads
the initramfs image and boot with it automatically
4. on the initramfs image, download the factory-uboot.bin image to the
device and perform sysupgrade with it and "-F" option
5. wait ~120 seconds to complete flashing
Notes:
- There are 2x factory*.bin images for different purposes.
- factory.bin : for flashing on OEM WebUI
- factory-uboot.bin: for flashing on OEM bootloader or initramfs image
factory-uboot.bin is useful for recoverying the device, or refreshing
when the kernel partition is expanded in the future. sysupgrade on
this device accepts factory-uboot.bin with option "-F", but on that
situation, user configurations won't be kept, so it's not for normal
use.
MAC addresses:
LAN : 18:EC:E7:xx:xx:E0 (board_data, "mac" (text))
WAN : 18:EC:E7:xx:xx:E0 (board_data, "mac" (text))
2.4 GHz: 18:EC:E7:xx:xx:E1 (Factory, 0x4 (hex))
5 GHz : 18:EC:E7:xx:xx:E4 (Factory, 0x8004 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Buffalo WSR-2533DHPLS is a 2.4/5 GHz band 11ac router, based on MediaTek
MT7621A.
Very similar to Buffalo WSR-2533DHPL, but with NAND, different GPIO
and TRX partitions.
Specification:
- SoC : MediaTek MT7621AT
- RAM : DDR3 256 MiB (Samsung K4B2G1646F-BYMA)
- Flash : RAW-NAND 128 MiB
(Winbond W29N01HV or KIOXIA TC58BVG0S3HTAI0)
- WLAN : 2.4/5 GHz (2x MediaTek MT7615N)
- Ethernet : 10/100/1000 Mbps
- Switch : MediaTek MT7530 (SoC) 4 ports
- LED/keys : 8x/6x (2x buttons, 1x slide-switch)
- UART : through-hole on PCB (J4)
- arrangement : 3.3V, GND, TX, RX from triangle-mark
- settings : 115200n8
- Power : 12VDC 1.5A
Flash instruction using factory.bin image:
1. boot WSR-2533DHPLS normally with "Router" mode
2. access to the WebI ("http://192.168.11.1/") on the device and open
firmware update page
("管理" -> "ファームウェア更新")
3. select the OpenWrt factory.bin image and click update ("更新実行")
button
Attention: do not use "factory-uboot.bin" image
4. Wait ~120 seconds to complete flashing
Flash instruction using initramfs image:
1. prepare the TFTP server with the initramfs image renamed to
"linux.trx-recovery" and IP address "192.168.11.2"
2. press the "AOSS" button while powering on the WSR-2533DHPLS
3. after 10 seconds, release the "AOSS" button, WSR-2533DHPLS downloads
the initramfs image and boot with it automatically
4. on the initramfs image, download the factory-uboot.bin image to the
device and perform sysupgrade with it and "-F" option
5. wait ~120 seconds to complete flashing
Notes:
- The embedded addresses in eeprom data in Factory partition have
Buffalo's OUI, but they don't match with the actual addresses
assigned to wlan devices. So fixup addresses by the user-space
script.
root@localhost:/# hexdump -C /dev/mtdblock3 | grep "^0000[08]000\s"
00000000 15 76 a0 00 88 57 ee bc 01 a8 15 76 c3 14 00 80 |.v...W.....v....|
00008000 15 76 a0 00 88 57 ee bc 01 f8 15 76 c3 14 00 80 |.v...W.....v....|
See "MAC addresses" below for actual addresses.
- There are 2x factory*.bin images for different purposes.
- factory.bin : for flashing on OEM WebUI
- factory-uboot.bin: for flashing on OEM bootloader or initramfs image
factory-uboot.bin is useful for recoverying the device, or refreshing
when the kernel partition is expanded in the future. sysupgrade on
this device accepts factory-uboot.bin with option "-F", but on that
situation, user configurations won't be kept, so it's not for normal
use.
MAC addresses:
LAN : 90:96:F3:xx:xx:30 (board_data, "mac" (text))
WAN : 90:96:F3:xx:xx:30 (board_data, "mac" (text))
2.4 GHz: 90:96:F3:xx:xx:31
5 GHz : 90:96:F3:xx:xx:38
[original work]
Signed-off-by: Audun-Marius Gangstø <audun@gangsto.org>
[convert to ubi, fix/improve DT, add sysupgrade support]
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Switch trx parser to parser_trx of Linux Kernel from mtdsplit_trx to
split firmware partition using model-specific trx magic number on
some Buffalo devices.
This change is tested on Buffalo WSR-2533DHPL.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Move Build/buffalo-trx to image-commands.mk from image/mt7622.mk to use
that definition from ramips as well.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
This pull request ports Ruijie RG-X60 Pro router support to the main branch.
Parameters:
- SoC : MediaTek MT7986A Quad-core ARM Cortex-A53 2.0GHz
- RAM : DDR3 512MiB (W634GU6QB)
- Flash : SPI-NAND 128 MiB (W25N01GVZEIG)
- WLAN : MediaTek MT7986A integration dual-band WiFi 6
- 2.4 GHz : b/g/n/ax, MIMO 4x4
- 5 GHz : a/n/ac/ax, MIMO 4x4
- Ethernet : 10/100/1000 Mbps x4 (MediaTek MT7531AE)
2500Mbps x 1 (Realtek RTL8221B-VB-CG)
- UART : through-hole on PCB
- [J500] GND, TX, RX, 3.3V (115200n1)
- Buttons : Mesh, Reset
- LEDs : 1x Power (Blue)
1x Turbo (Purple)
- Power : 12 VDC, 3 A
How to Installation:
1. Remove the case and connect the TTL cable to the corresponding position.
2. Power on the device and quickly press "down" on the keyboard, then
U-Boot will stay in the menu.
3. Select "1. Upgrade Firmware", select "0. TFTP Client(Default)".
4. Input the IP address, input the Openwrt image file name to be
flashed, start the TFTP server, and press "Enter".
5. Wait for the flashing to complete.
How return to stock:
1. Remove the case and connect the TTL cable to the corresponding
position.
2. Power on the device and quickly press "down" on the keyboard, then
U-Boot will stay in the menu.
3. Select "1. Upgrade Firmware", select "0. TFTP Client(Default)".
4. Input the IP address, input the Stock “E-WEBOS” image file name to
be flashed, start the TFTP server, and press "Enter".
5. Wait for the flashing to complete.
About recovery:
Connect uart, use u-boot menu to flash stock firmware image or boot
OpenWrt initramfs image.
About MAC Address:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 10:82:3D:XX:XX:9E | label |
| LAN | 10:82:3D:XX:XX:9F | label+1 |
| WLAN 2g | 10:82:3D:XX:XX:A0 | label+2 |
| WLAN 5g | 10:82:3D:XX:XX:A1 | label+3 |
+---------+-------------------+-----------+
Signed-off-by: Ashley Lee <code@emtips.net>
The Yafut tool now has limited capabilities for working on filesystem
images stored in regular files. This enables preparing Yaffs2 images
for devices with NOR flash using upstream Yaffs2 filesystem code instead
of the custom kernel2minor tool.
Since minimizing the size of the resulting filesystem image size is
important and upstream Yaffs2 code requires two allocator reserve blocks
to be available when writing a file to the filesystem, a trick is
employed while preparing an OpenWRT image: the blank filesystem image
that Yafut operates on initially contains two extra erase blocks that
are chopped off after the kernel file is written. This is safe to do
because Yaffs2 has a true log structure and therefore only ever writes
sequentially (and the size of the kernel file is known beforehand).
While the two extra erase blocks are necessary for writes, Yaffs2 code
seems to be perfectly capable of reading back files from a "truncated"
filesystem that does not contain these extra erase blocks.
In terms of image size, this new approach is only marginally worse than
the current kernel2minor-based one: specifically, upstream Yaffs2 code
needs to write three object headers (each of which takes up an entire
data chunk) when the kernel file is written to the filesystem:
- an object header for the kernel file when it is created,
- an object header for the root directory when the kernel file is
created,
- an updated object header for the kernel file when the latter is
fully written (so that its new size can be recorded).
kernel2minor only writes two of these headers, which is the absolute
minimum required for reading the file back. This means that the
Yafut-based approach causes firmware images to be at most one erase
block (64 kB) larger than those created using kernel2minor, but only in
the very unfortunate scenario where the size of the kernel file is
really close to a multiple of the erase block size.
The rest of the calculations performed when the empty filesystem image
is first prepared stems from the Yaffs2 layout used by MikroTik NOR
devices: each 65,536-byte erase block contains 63 chunks, each of which
consists of 1024 bytes of data followed by 16-byte Yaffs tags without
ECC data; each such group of 63 chunks is then followed by 16 bytes of
padding, which translates to "-C 1040 -B 64k -E" in the Yafut
invocation. Yaffs2 checkpoints and summaries are disabled (using
Yafut's -P and -S switches, respectively) as they are merely performance
optimizations that require extra storage space. The -L and -M switches
are used to force little-endian or big-endian byte order (respectively)
in the resulting filesystem image, no matter what byte order the build
host uses. The tr invocation is used to ensure that the filesystem
image is initialized with 0xFF bytes (which are an indicator of unused
space for Yaffs2 code).
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
Link: https://github.com/openwrt/openwrt/pull/13453
Signed-off-by: Robert Marko <robimarko@gmail.com>
Instead of extracting WiFi precal as well as MAC addresses in userspace
use recently introduced NVMEM-on-UBI instead.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Christian Lamparter <chunkeey@gmail.com>
Hardware:
- SoC: MediaTek MT7628AN (MIPS 580MHz)
- Flash: 16 MiB XMC 25QH128CH10
- RAM: 128 MiB ESMT M14D1G1664A
- WLAN: 2.4 GHz (MT7628), 5 GHz (MT7613BEN 802.11ac)
- Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628)
- USB 2.0 port
- Buttons: 1 Reset button, 1 slider button
- LEDs: 1x Red, 1x White
- Serial console: unpopulated header, 115200 8n1
- Power: 5 VDC, 2 A
MAC addresses:
+---------+-------------------+-----------+
| | MAC | Algorithm |
+---------+-------------------+-----------+
| WAN | 80:af:ca:xx:xx:x0 | label |
| LAN | 80:af:ca:xx:xx:x0 | label |
| WLAN 2g | 80:af:ca:xx:xx:x0 | label |
| WLAN 5g | 80:af:ca:xx:xx:x2 | label+2 |
+---------+-------------------+-----------+
Installation:
The installation must be done via TFTP by disassembling the router.
On other occasions Cudy has distributed intermediate firmware to make
installation easier, and so I recommend checking the Wiki for this
device if there is a more convenient solution than the one below.
To install using TFTP:
1. Upgrade to a beta firmware (signed by Cudy) that can be downloaded
from the wiki. This is required in order to use an unlocked u-boot.
2. Connect to UART.
3. While the router is turning on, press 1.
4. Connect to LAN and set your IP to 192.168.1.88/24. Configure a TFTP
server and an OpenWrt initramfs-kernel.bin firmware file as recovery.bin.
5. Press Enter three times. Verify the filename.
6. If you can reach LuCI or SSH now, just use the sysupgrade image with
the 'Keep settings' option turned off.
If you don't want to use the beta firmware nor the unlocked u-boot, you
can install the firmware writing the sysupgrade image on the firmware
partition of the SPI flash.
Signed-off-by: Luis Mita <luis@luismita.com>
For MT7620, we should always prevent main ethernet interface from
going down due to phy link changes. And the ralink net driver does
not support cable test function, so this patch won't change any
behavior.
Ref:
6fcba5eec3 ("ramips: port 0034-NET-multi-phy-support.patch to 5.4")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/15591
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
CI tells us that we need to, so lets refresh them.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
Select 6.6 as testing kernel on bcm47xx.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
Since 6.1 is now default, drop 5.15 support.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
Default to kernel 6.1 on bcm47xx.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
Refresh kernel patches. Remove patches already included in the kernel.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15010
Signed-off-by: Robert Marko <robimarko@gmail.com>
Use ath11k_patch_mac and ath11k_set_macflag functions
instead of fix_wifi_mac script.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/15580
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for D-Link DIR-2055 A1 based on similarities to DIR-1960 A1,
as well as various DIR-8xx A1 models. Existing DIR-1960 A1 openwrt
"factory" firmware installs without modifications via the D-Link Recovery
GUI and has no known incompatibilities with the DIR-2055 A1.
Changes to be committed:
new file: target/linux/ramips/dts/mt7621_dlink_dir-2055-a1.dts
modified: target/linux/ramips/image/mt7621.mk
modified: target/linux/ramips/mt7621/base-files/etc/board.d/01_leds
modified: target/linux/ramips/mt7621/base-files/lib/upgrade/platform.sh
Specifications:
Board: Not known
SoC: MediaTek MT7621 Family (MT7621AT)
RAM: 256 MB (Micron 9OK17 D9PTK, should be DDR3 MT41K128M16JT-125)
Flash: 128 MB (Winbond W29N01HVSINA)
WiFi: MediaTek MT7615 Family (MT7615N x2)
Switch: 1 WAN, 4 LAN (Gigabit)
Ports: 1 USB 3.0 (front)
Buttons: Reset, WiFi Toggle, WPS
LEDs: Power (white/orange), Internet (white/orange),
WiFi 2.4G (white), WiFi 5G (white)
Notes:
Only known difference vs. the DIR-1960 A1 is that the DIR-2055 A1
doesn't have a USB activity LED
Serial port:
Tested to be identical to various DIR-8xx A1 models with a similar
enclosure/pcb design:
Parameters: 57600, 8N1, 3.3V TTL no flow control
Location: J1 header (close to the Reset, WiFi and WPS buttons)
Pinout: 1 - VCC 2 - RXD 3 - TXD 4 - GND
Did not connect VCC when using
Installation:
D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to
http://192.168.0.1
Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Keith Harrison <keithh@protonmail.com>
The option CONFIG_SND_DRIVERS is activated by default in the generic
configuration, do not deactivate it for tegra. This fixes the build of
the kmod-sound-dummy package on tegra.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Split the kmod-video-dma into kmod-video-dma-sg and
kmod-video-dma-contig. The old one contained two kmods, but sometimes
only one of them is build which caused problems. The configuration
options are not manually selectable in the kernel and hidden in OpenWrt.
Currently this causes build failures on some targets.
Fixes: 4d7cbe0a55 ("kernel: video-dma: explicitly state packaged modules")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
We don't have any passive trip point hence we can set the polling delay
for passive trip to 0 effectively disabling this polling.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Split thermal zone for puzzle chassis. Thermal platform supports only
one sensor per thermal zone.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix missing property in puzzle thermal. The thing was never supposed to
work.
Property #thermal-sensor-cells was missing from the puzzle hwmon, making
the entire thermal platform referencing that fail to probe with -EINVAL.
The puzzle hwmon expose 2 termistor but they probably use an userspace
downstream utility to configure and handle thermal. For this reason we
really don't know what they use the sensor for or when it's attached.
We use them to sensor if the Chassis gets too hot due to ambient
temperature and generic components getting too warm.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
- Make step_wise thermal governor respect hysteresis
This is done by importing a downstream patch, backporting the same feature
now present in Linux v6.10+ would be too messy.
- Introduce thermal zone for the WT61P803 uC (chassis and board sensors)
- Introduce thermal zones for AQR NBase-T PHYs
- No longer modify existing SoC thermal zones (which are now only in charge
for emergency shutdown, and can be interrupt driven instead of polled)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Hardware
--------
CPU: Freescale P1020 2xe500 PPC
RAM: 256M DDR3 (Micron MT41J64M16JT-15E:G "D9MNJ")
NAND: 128M (Micron 2CA1)
BTN: 1x Reset
LED: Power - ETH - Radio1 - Radio2
UART: RJ-45 Cisco Pinout - 115200 8N1
Installation
------------
NOTE: You can find a repo with up-to-date instructions as well as
the required files here:
https://github.com/blocktrron/msm460-flashing
Required files
==============
You need a command-files as well as a U-Boot image.
The command-file has the following content (padded to 131072 bytes).
If you copy paste these, remove the newlines!
```
U-BOOT setenv ethaddr 02:03:04:05:06:07; setenv ipaddr 192.168.1.1;
setenv serverip 192.168.1.66; tftpboot 0x3000000 msm460-uboot.bin;
nand device; nand erase 0 0xC0000; nand write 0x3000000 0x0 0xC0000; reset
```
You can download the required U-Boot from this repository:
https://github.com/blocktrron/u-boot-msm/releases
Preparation
===========
Prepare a TFTP server serving two files:
- U-Boot NAND image as `msm460-uboot.bin`.
- OpenWrt factory image as `msm460-factory.bin`
- Command-file names `commands.tftp`
You can start a TFTP server in the current directory using dnsmasq:
```bash
sudo dnsmasq --no-daemon --listen-address=0.0.0.0 \
--port=0 --enable-tftp=enxd0 --tftp-root="$(pwd)" \
--user=root --group=root
```
Replace `enxd0` with the name of your network interface.
Procedure
=========
1. Assign yourself the IP-Address 192.168.1.66/24.
3. Connect the Router to the PC while keeping the reset button
pressed.
4. The LEDs will eventually begin to flash.
They will start to flash faster after around 15 seconds.
5. Release the reset button.
6. Start a new shell
7. Make sure you are currently in the directory where the tftp server
is located.
8. Run the following command:
```bash
tftp 192.168.1.1 -m binary -c put commands.tftp nflashd.cccc9999
```
You get the message "Transfer timed out."
To find out if you have been successful, please check the
blinking LED Pattern.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a universal zImage which can be loaded by mpc85xx boards at
load address 0x3000000. This allows boards to boot kernels larger than
16MB even if the image is loaded temporarily from NAND at offset
0x1000000 which some bootloaders do by default.
Signed-off-by: David Bauer <mail@david-bauer.net>
Dual-slot NAS based on Marvell Kirkwood.
Specifications:
- Marvell 88F6702 @1GHz
- 256Mb RAM
- 128Mb NAND
- 1x GbE LAN (Marvell 88E1318R)
- 1x USB 2.0
- 2x SATA
- Weltrend WT69P3 ("supervisor" MCU chip)
- Serial on J2 (115200,8n1)
- Newer bootROM so kwboot-ing via serial is possible
Notes:
- The Weltrend MCU is controlled by the package added in utils/dns320l-mcu.
- The original MAC address is stored in the "mini firmware" image's first
17 bytes.
- Compared to the original MTD layout, the uImage+rootfs are now stored in
a common ubi partition.
Installation:
1. Serial console
- Connect your levelshifter to the serial console
on J2 (refer to the wiki page for pinout)
2. Update u-boot
- Download the u-boot.kwb image for the device
- Powercycle the NAS
- Run "kwboot -b u-boot-dns320l/u-boot.kwb /dev/ttyUSB0 -p"
- Connect to the serial console with minicom
- tftp 0x0800000 u-boot-dns320l/u-boot.kwb
(Please note that "PHY reset timed out" seems to be customary
on kirkwood devices, the egiga0 interface works regardless.)
- nand erase 0x0 100000
- nand write 0x0800000 0x0 0x100000
- reset
3. Install OpenWrt
- Boot up the initramfs image
- tftpboot 0x800000 openwrt-kirkwood-generic-dlink_dns320l-initramfs-uImage; bootm 0x800000
- Download the sysupgrade image and perform sysupgrade
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Reviewed-by: Pawel Dembicki <paweldembicki@gmail.com>
Fix broken IB_STANDALONE option for OPKG due to an error in ifdef logic
where we weren't adding the required entry to reference the local files
in repositories.conf
Rework the ifdef to more explicit and restore original functionality of
this option.
While at it also provide different README for APK or OPKG.
Fixes: d788ab376f ("build: add APK package build capabilities")
Link: https://github.com/openwrt/openwrt/pull/15599
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Upstream commit 83b7f0b8aeab ("ARM: tegra: Add OPP tables and power
domains to Tegra20 device-trees") added power domains to all devices
supporting power management and one of them is Video Decoder Engine.
Because of lacking driver for VDE, its power gate couldn't be driven
which inhibited reboot of the whole device.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Simple refresh to get rid of any fuzz and drop serial patch. With few
bug fixes around tegra serial driver the spurious IRQ didn't appear any
more during test. Let's see how long that'll last.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Use a simple Shell script like on filogic target to get rid of downstream
patch for the Ethernet driver which was rejected upstream long ago.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds the legacy /dev/fb* device file for kernel 6.6 again.
Linux upstream commit 701d2054fa31 ("fbdev: Make support for
userspace interfaces configurable") made this configurable and we
deactivated this option by default for kernel 6.6. On x86 we are not
space constrained and some users need this legacy interface.
Fixes: #15222
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport commit fixing detection of SFP modules which has been broken
since Linux 6.4 for some modules.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In preparation to update to upcoming Linux 6.6.33 move accepted patches
from mediatek target to backport folder, so moving to newer Linux 6.6
releases becomes easier and also other patches on top can be applied
more easily.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Make sure all patches can again be applied using 'git am' on the
corresponding linux-stable git tree.
Fixes: a7ae4ed0a3 ("kernel: fix tools build breakage on macos with x86")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Fix compile error:
drivers/dma/ralink-gdma.c: In function 'gdma_dma_config':
drivers/dma/ralink-gdma.c:197:40: error: 'struct dma_slave_config' has no member named 'slave_id'
197 | chan->slave_id = config->slave_id;
| ^~
drivers/dma/ralink-gdma.c:206:40: error: 'struct dma_slave_config' has no member named 'slave_id'
206 | chan->slave_id = config->slave_id;
| ^~
make[8]: *** [scripts/Makefile.build:243: drivers/dma/ralink-gdma.o] Error 1
ref: https://lore.kernel.org/all/20211122222203.4103644-1-arnd@kernel.org/
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The gdma driver has been removed from the upstream. Let's move it
to the local files. This patch also removed unsupported compatible
string and sub-target.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Add missing ';;' to the end of shell switch case statement.
Fixes: c71b68acdd ("mediatek: filogic: add Adtran SmartRG Mount Stuart series")
Reported-by: @gl-dude
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Disable image building for the board, since the kernel of the main branch
is to big to fit into the kernel partition.
Signed-off-by: Nick Hainke <vincent@systemli.org>
Dell/SonicWall APL26-0AE (marketed as SonicPoint ACe) is a dual band
wireless access point. End of life as of 2022-07-31.
Specification
SoC: QualcommAtheros QCA9550
RAM: 256 MB DDR2
Flash: 32 MB SPI NOR
WIFI: 2.4 GHz 3T3R integrated
5 GHz 3T3R QCA9890 oversized Mini PCIe card
Ethernet: 2x 10/100/1000 Mbps QCA8334
port labeled lan1 is PoE capable (802.3at)
USB: 1x 2.0
LEDs: LEDs: 6x which 5 are GPIO controlled and two of them are dual color
Buttons: 2x GPIO controlled
Serial: RJ-45 port, SonicWall pinout
baud: 115200, parity: none, flow control: none
Before flashing, be sure to have a copy of factory firmware, in case You
wish to revert to original firmware.
All described procedures were done in following environment:
ROM Version: SonicROM (U-Boot) 8.0.0.0-11o
SafeMode Firmware Version: SonicOS 8.0.0.0-14o
Firmware Version: SonicOS 9.0.1.0
In case of other versions, following installation instructions might be
ineffective.
Installation
1. Prepare TFTP server with OpenWrt sysupgrade image and rename that
image to "sp_fw.bin".
2. Connect to one of LAN ports.
3. Connect to serial port.
4. Hold the reset button (small through hole on side of the unit),
power on the device and when prompted to stop autoboot, hit any key.
The held button can now be released.
5. Alter U-Boot environment with following commands:
setenv bootcmd bootm 0x9F110000
saveenv
6. Adjust "ipaddr" (access point, default is 192.168.1.1) and "serverip"
(TFTP server, default is 192.168.1.10) addresses in U-Boot
environment, then run following commands:
tftp 0x80060000 sp_fw.bin
erase 0x9F110000 +0x1EF0000
cp.b 0x80060000 0x9F110000 $filesize
7. After successful flashing, execute:
boot
8. The access point will boot to OpenWrt. Wait few minutes, until the
wrench LED will stop blinking, then it's ready for configuration.
Known issues
Initramfs image can't be bigger than specified kernel size, otherwise
bootloader will throw LZMA decompressing error. Switching to lzma-loader
should workaround that.
This device has Winbond 25Q256FVFG and doesn't have reliable reset, which
causes hang on reboot, thus broken-flash-reset needs to be added. This
property addition causes dispaly of "scary" warning on each boot, take
this warnig into consideration.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
After the spliting dts folder of ARM architecture in upstream,
layerscape routines need to be adjusted for new solution.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Mostly done by 'make kernel_oldconfig'.
armv8_64b has added one entry manually:
CONFIG_CRYPTO_CURVE25519=y
as workaround for error:
aarch64-openwrt-linux-musl-ld: crypto/crypto_engine.o: in function
`crypto_engine_register_kpp':
crypto_engine.c:687: undefined reference to `crypto_register_kpp'
crypto_engine.c:687:(.text+0x57c): relocation truncated to fit:
R_AARCH64_CALL26 against undefined symbol `crypto_register_kpp'
aarch64-openwrt-linux-musl-ld: crypto/crypto_engine.o: in function
`crypto_engine_unregister_kpp':
crypto/crypto_engine.c:693: undefined reference to `crypto_unregister_kpp'
crypto_engine.c:693:(.text+0x5a0): relocation truncated to fit:
R_AARCH64_CALL26 against undefined symbol `crypto_unregister_kpp'
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
