Add the gpio-restart driver to the realtek build. This way devices,
which cannot reliably perform resets using the SoC's internal reset
logic, can use a GPIO line to drive the SoC's hard reset input.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The internal GPIO controller on RTL838x is also an IRQ controller, which
requires the 'interrupt-controller' and '#interrupts-cells' properties
to be present in the device tree.
Reported-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Some devices are assigned globally unique MAC addresses for all
ports. These are stored by U-Boot in the second U-Boot enviroment
("sysinfo") as a range of start and end address.
Use the full range if provided.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
The default management interface should be easy to find for users
doing "blind" installations without console access. There are
already multiple examples in the forum of advanced early adopters
having problems locating the management interface after installing
OpenWrt.
Requiring tagged VLAN configration to access the initial management
interface creates unnecessary hassle at best. Errors on the other
end are close to impossible to debug without console access, even
for advanced users. Less advanced users might have problems with
the concept of VLAN tagging.
Limiting management access to a single arbitrary port among up to
52 possible LAN ports makes this even more difficult, for no
reason at all. Users might have reasons to use a different port
for management. And they might even have difficulties using the
OpenWrt selected one. The port might be the wrong type for their
management link (e.g copper instead of fibre). Or they might
depend on PoE power from a device which they can't reconfigure.
User expectations will be based on
- OpenWrt defaults for other devices
- stock firmware default for the device in question
- common default behaviour of similar devices
All 3 cases point to a static IP address accessible on the native
VLAN of any LAN port. A switch does not have any WAN port. All
ports are LAN ports.
This changes the default network configuration in line with these
expectations.
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
The configs/omap3_overo_defconfig file was removed from upstream U-Boot
in commit ed3294d6d1f9 ("arm: Remove overo board"). Remove it in OpenWrt
too. If someone needs this please add it also to upstream U-Boot.
This fixes the compile of the omap target.
Fixes: ffb807ec90 ("omap: update u-boot to 2021.07")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch adds support for the Teltonika RUTX10.
This device is an industrial DIN-rail router with 4 ethernet ports,
2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs.
The RUTX series devices are very similiar so common parts of the DTS
are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev
board.
See https://teltonika-networks.com/product/rutx10 for more info.
Hardware:
SoC: Qualcomm IPQ4018
RAM: 256MB DDR3
SPI Flash 1: XTX XT25F128B (16MB, NOR)
SPI Flash 2: XTX XT26G02AWS (256MB, NAND)
Ethernet: Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports
WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n
Wifi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac
USB Hub: Genesys Logic GL852GT
Bluetooth: Qualcomm CSR8510 (A10U)
LED/GPIO controller: STM32F030 with custom firmware
Buttons: Reset button
Leds: Power (green, cannot be controlled)
WiFi 2.4G activity (green)
WiFi 5G activity (green)
MACs Details verified with the stock firmware:
eth0: Partition 0:CONFIG Offset: 0x0
eth1: = eth0 + 1
radio0 (2.4 GHz): = eth0 + 2
radio1 (5.0 GHz): = eth0 + 3
Label MAC address is from eth0.
The LED/GPIO controller needs a separate kernel driver to function.
The driver was extracted from the Teltonika GPL sources and can be
found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt
USB detection of the bluetooth interface is sometimes a bit flaky. When
not detected power cycle the device. When the bluetooth interface was
detected properly it can be used with bluez / bluetoothctl.
Flash instructions via stock web interface (sysupgrade based):
1. Set PC to fixed ip address 192.168.1.100
2. Push reset button and power on the device
3. Open u-boot HTTP recovery at http://192.168.1.1
4. Upload latest stock firmware and wait until the device is rebooted
5. Open stock web interface at http://192.168.1.1
6. Set some password so the web interface is happy
7. Go to firmware upgrade settings
8. Choose
openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi
9. Set 'Keep settings' to off
10. Click update, when warned that it is not a signed image proceed
Return to stock firmware:
1. Set PC to fixed ip address 192.168.1.100
2. Push reset button and power on the device
3. Open u-boot HTTP recovery at http://192.168.1.1
4. Upload latest stock firmware and wait until the device is rebooted
Note: The DTS expects OpenWrt to be running from the second rootfs
partition. u-boot on these devices hot-patches the DTS so running from the
first rootfs partition should also be possible. If you want to be save follow
the instructions above. u-boot HTTP recovery restores the device so that when
flashing OpenWrt from stock firmware it is flashed to the second rootfs
partition and the DTS matches.
Signed-off-by: Felix Matouschek <felix@matouschek.org>
The MR42 and MR52 are two similar IPQ806x based devices from the Cisco
Meraki "Cryptid" series.
MR42 main features:
- IPQ8068 1.4GHz
- 512MB RAM
- 128MB NAND
- 2x QCA9992 (2.4 & 5GHz)
- 1x QCA9889 (2.4 & 5GHz)
- 1x AR8033 PHY
- PoE/AC power
MR52 main features:
- IPQ8068 1.4GHz
- 512MB RAM
- 128MB NAND
- 2x QCA9994 (2.4 & 5GHz)
- 1x QCA9889 (2.4 & 5GHz)
- 2x AR8033 PHYs
- PoE/AC power
(MR42 Only) Installation via diagnostic mode:
If you can successfully complete step 1 then you can continue to install
via this method without having to open the device. Otherwise please use
the standard UART method. Please note that when booting via TFTP, some
Ethernet devices, in particular those on laptops, will not connect in
time, resulting in TFTP boot not succeeding. In this instance it is
advised to connect via a switch.
1. Hold down reset at power on and keep holding, after around 10 seconds
if the orange LED changes behaviour to begin flashing, proceed to
release reset, then press reset two times. Ensure that the LED has
turned blue. Note that flashing will occur on some devices, but it
will not be possible to change the LED colour using the reset button.
In this case it will still be possible to continue with this install
method.
2. Set your IP to 192.168.1.250. Set up a TFTP server serving
mr42_u-boot.mbn and
openwrt-ipq806x-generic-meraki_mr42-initramfs-fit-uImage.itb, obtained
from [1].
3. Use telnet and connect to 192.168.1.1. Run the following commands to
install u-boot. Note that all these commands are critical, an error
will likely render the device unusable.
Option 3.1:
If you are sure you have set up the TFTP server correctly you can
run this script on the device. This will download and flash the
u-boot image immediately:
`/etc/update_uboot.sh 192.168.1.250 mr42_u-boot.mbn`
Once completed successfully, power off the device.
Option 3.2:
If you are unsure the TFTP server is correctly set up you can
obtain the image and flash manually:
3.2.1. `cd /tmp`
3.2.2. `tftp-hpa 192.168.1.250 -m binary -c get mr42_u-boot.mbn`
3.2.3. Confirm file has downloaded correctly by comparing the
md5sum:
`md5sum mr42_u-boot.mbn`
3.2.4. The following are the required commands to write the image.
`echo 1 > /sys/devices/platform/msm_nand/boot_layout
mtd erase /dev/mtd1
nandwrite -pam /dev/mtd1 mr42_u-boot.mbn
echo 0 > /sys/devices/platform/msm_nand/boot_layout`
Important: You must observe the output of the `nandwrite`
command. Look for the following to verify writing is occurring:
`Writing data to block 0 at offset 0x0
Writing data to block 1 at offset 0x20000
Writing data to block 2 at offset 0x40000`
If you do not see this then do not power off the device. Check
your previous commands and that mr42_u-boot.mbn was downloaded
correctly. Once you are sure the image has been written you
can proceed to power off the device.
4. Hold the reset button and power on the device. This will immediately
begin downloading the appropriate initramfs image and boot into it.
Note: If the device does not download the initramfs, this is likely
due to the interface not being brought up in time. Changing Ethernet
source to a router or switch will likely resolve this. You can also
try manually setting the link speed to 10Mb/s Half-Duplex.
5. Once a solid white LED is displayed on the device, continue to the
UART installation method, step 6.
Standard installation via UART - MR42 & MR52
1. Disassemble the device and connect a UART header. The header pinout
is as follows:
1 - 3.3v
2 - TXD
3 - RXD
4 - GND
Important: You should only connect TXD, RXD and GND. Connecting
3.3v may damage the device.
2. Set your IP to 192.168.1.250. Set up a TFTP server serving
openwrt-ipq806x-generic-meraki_(mr42|mr52)-initramfs-fit-uImage.itb.
Separately obtain the respective sysupgrade image.
3. Run the following commands, preferably from a Linux host. The
mentioned files, including ubootwrite.py and u-boot images, can be
obtained from [1].
`python ubootwrite.py --write=(mr42|mr52)_u-boot.bin`
The default for "--serial" option is /dev/ttyUSB0.
4. Power on the device. The ubootwrite script will upload the image to
the device and launch it. The second stage u-boot will in turn load
the initramfs image by TFTP, provided the TFTP server is running
correctly. This process will take about 13 minutes. Once a solid
white LED is displayed, the image has successfully finished
loading. Note: If the image does not load via TFTP, try again with
the Ethernet link to 10Mb/s Half-Duplex.
5. (MR42 only) Do not connect over the network. Instead connect over
the UART using minicom or similar tool. To replace u-boot with
the network enabled version, please run the following commands.
Note that in the provided initramfs images, the u-boot.mbn file
is located in /root:
If you have not used the provided initramfs, you must ensure you
are using an image with "boot_layout" ECC configuration enabled in
the Kernel. This will be version 5.10 or higher. If you do not do
this correctly the device will be bricked.
`insmod mtd-rw i_want_a_brick=1
mtd erase /dev/mtd8
nandwrite -pam /dev/mtd8 /root/mr42_u-boot.mbn`
After running nandwrite, ensure you observe the following output:
`Writing data to block 0 at offset 0x0
Writing data to block 1 at offset 0x20000
Writing data to block 2 at offset 0x40000`
6. (Optional) If you have no further use for the Meraki OS, you can
remove all other UBI volumes on ubi0 (mtd11), including diagnostic1,
part.old, storage and part.safe. You must not remove the ubi1 ART
partition (mtd12).
`for i in diagnostic1 part.old storage part.safe ; do
ubirmvol /dev/ubi0 -N $i
done`
7. Proceed to flash the sysupgrade image via luci, or else download or
scp the image to /tmp and use the sysupgrade command.
[1] The mentioned images and ubootwrite.py script can be found in this repo:
https://github.com/clayface/openwrt-cryptid
[2] The modified u-boot sources for the MR42 and MR52 are available:
https://github.com/clayface/U-boot-MR52-20200629
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Add backports of the following patches:
"net: stmmac: explicitly deassert GMAC_AHB_RESET" and
"ARM: dts: qcom: add ahb reset to ipq806x-gmac"
Required for Meraki MR42/MR52.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Rather than having separate patches for each GSBI node added, this patch
consolidates the existing GSBI1 patch into
083-ipq8064-dtsi-additions.patch. In addition, GSBI6 and GSBI7 I2C nodes,
required for the MR42 and MR52 respectively, are added.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
This adds support for the MikroTik RouterBOARD RBD53iG-5HacD2HnD
(hAP ac³), a indoor dual band, dual-radio 802.11ac
wireless AP with external omnidirectional antennae, USB port, five
10/100/1000 Mbps Ethernet ports and PoE passthrough.
See https://mikrotik.com/product/hap_ac3 for more info.
Specifications:
- SoC: Qualcomm Atheros IPQ4019
- RAM: 256 MB
- Storage: 16 MB NOR + 128 MB NAND
- Wireless:
· Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
· Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi antennae
- Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port,
passive PoE in, PoE passtrough on port 5
- 1x USB Type A port
Installation:
1. Boot the initramfs image via TFTP
2. Run "cat /proc/mtd" and look for "ubi" partition mtd device number, ex. "mtd1"
3. Use ubiformat to remove MikroTik specific UBI volumes
* Detach the UBI partition by running: "ubidetach -d 0"
* Format the partition by running: "ubiformat /dev/mtdN -y"
Replace mtdN with the correct mtd index from step 2.
3. Flash the sysupgrade image using "sysupgrade -n"
Signed-off-by: Robert Marko <robimarko@gmail.com>
Tested-by: Mark Birss <markbirss@gmail.com>
Tested-by: Michael Büchler <michael.buechler@posteo.net>
Tested-by: Alex Tomkins <tomkins@darkzone.net>
All patches automatically rebased.
Build system: x86_64
Build-tested: ramips/mt7621*
*I am hit with the binutils 2.37 bug so I had to revert 7f1edbd412
in order to downgrade to 2.35.1
Signed-off-by: John Audia <graysky@archlinux.us>
Steven Maddox reported in the OpenWrt bugzilla, that his
RaidSonic IB-NAS4220-B was no longer booting with the new
OpenWrt 21.02 (uses linux 5.10's device-tree). However, it was
working with the previous OpenWrt 19.07 series (uses 4.14).
(This is still under investigation.)
Bugzilla: https://bugs.openwrt.org/index.php?do=details&task_id=4137
Reported-by: Steven Maddox <s.maddox@lantizia.me.uk>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
the Netgear EX6100v2 and EX6150v2 can utilize the nvmem
for the pre-calibration and mac-address for both WIFI
devices.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
For v2, both ath9k (2.4GHz Wifi) and ath10k (5 GHz) driver now
pull the (pre-)calibration data from the nvmem subsystem. v1
is slightly different as only the ath9k Wifi is supported.
This allows us to move the userspace caldata extraction
and mac-address patching for the 5GHZ ath10k supported
wifi into the device-tree definition of the device.
ath9k's nodes are also changed over to use nvmem-cells
over OpenWrt's custom mtd-cal-data property.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Martin Kennedy reported:
|Presently, I get this kernel panic on mpc85xx (Aerohive HiveAP 370)
|on OpenWrt 'master' which occurs right as the second processor is
|initialized:
|
|[ 0.478804] rcu: Hierarchical SRCU implementation.
|[ 0.535569] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
|[ 0.627233] smp: Bringing up secondary CPUs ...
|[ 0.681659] kernel tried to execute user page (0) - exploit attempt? (uid: 0)
|[ 0.766618] BUG: Unable to handle kernel instruction fetch (NULL pointer?)
|[ 0.848899] Faulting instruction address: 0x00000000
|[ 0.908273] Oops: Kernel access of bad area, sig: 11 [#1]
|[ 0.972851] BE PAGE_SIZE=4K SMP NR_CPUS=2 P1020 RDB
|[ 1.031179] Modules linked in:
|[ 1.067640] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.10.80 #0
|[ 1.139507] NIP: 00000000 LR: c0021d2c CTR: 00000000
|[ 1.199921] REGS: c1051cf0 TRAP: 0400 Not tainted (5.10.80)
|[...]
|[ 1.758220] NIP [00000000] 0x0
|[ 1.794688] LR [c0021d2c] smp_85xx_kick_cpu+0xe8/0x568
|[ 1.856126] Call Trace:
|[ 1.885295] [c1051da8] [c0021cb8] smp_85xx_kick_cpu+0x74/0x568 (unreliable)
|[ 1.968633] [c1051de8] [c0011460] __cpu_up+0xc0/0x228
|[ 2.029038] [c1051e18] [c0031bbc] bringup_cpu+0x30/0x224
|[ 2.092572] [c1051e48] [c0031f3c] cpu_up.constprop.0+0x180/0x33c
|[..]
|[ 2.727952] ---[ end trace 9b796a4bafb6bc14 ]---
|[ 3.800879] Kernel panic - not syncing: Fatal exception
|[ 3.862353] Rebooting in 1 seconds..
|[ 5.905097] System Halted, OK to turn off power
|
|I bisected this down to commit 3ae5da5adc ("kernel: bump 5.10 to 5.10.80");
|that is, I don't get the panic right before this commit, but I do after.
He reported the issue upstream and Xiaoming Ni from huawei came up with
the patch (that is on it's way to upstream). While the AP370 is not in
Openwrt, this will likely affect other SMP P1020 devices OpenWrt ships
with: like the AP330, Enterasys WS-AP3710i, etc.
Reported-by: Martin Kennedy <hurricos@gmail.com>
Tested-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
these flags have been creeping in from the QSDK.
All needed clocks should be accounted for, and
if a device is broken due to this. It should be
looked into.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The board has a fixed size kernel partition but do not limit the kernel
size during image building.
Disable image building for both boards as well, since the kernel of the
last release as well as master are to big to fit into the 2 MByte kernel
partition.
Signed-off-by: Mathias Kresin <dev@kresin.me>
The current state of the kernel 5.4 support is in the openwrt-21.02
branch. No need to keep a not default used kernel in this branch.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [VRX268/ bthub5]
With Kernel 5.10 the ar7 FRITZ!Box are not booting the initramfs nor the
sysupgrade image any more. Presumably due to the grown kernel.
Use the okli preloader to workaround the bootloader issue. No solution
so far for the initramfs.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Removed due to being unused with 1f7a03a706, but now required for the
ar7 FRITZ!Box.
Could be used for the ARV7519RW22 as well, for which the image
generation was disabled due to a stock u-boot issue with kernel bigger
than 2 MByte.
The code is combination of the ath79 and ramips okli loader.
Signed-off-by: Mathias Kresin <dev@kresin.me>
By dropping _machine_restart, users can provide more reliable or
device-specific restart modes.
_machine_halt was already removed in commit f4b687d1f0 ("realtek: use
kernel defined halt"), but quietly reintroduced in commit 8faffa00cb
("realtek: add support for the RTL9300 timer"). Let's remove it again.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Add and enable the Realtek Otto WDT peripheral found on these SoCs.
Default all devices to use standard (cold) reboot and "soc" resets.
Devices that require the PLL value fixup before restarting, should pick
the "cpu" or "software" reset mode. These devices also need to provide a
custom reboot mode, by adding the reboot argument to the kernel command
line:
WDT reset mode | kernel reboot mode
----------------+---------------------------------------
soc | reboot=cold (default if not specified)
cpu | reboot=warm
software | reboot=software
Preferrably, these devices should use an alternative restart method like
gpio-restart to provide reliable restarts.
Note that watchdog restarts are not yet exposed, since the
_machine_restart override is still present.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Add patch submitted upstream to linux-watchdog and replace the MIPS
architecture symbols. Requires one extra patch for the DIV_ROUND_*
macros, which have moved to a different header since 5.10.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
The CPU peripherals on RTL83xx/RTL930x are connected to the CPU via the
Lexra bus. This bus can provide a clock signal to these peripherals, but
no clock driver is currently available. Instead, use a fixed-clock to
provide the clock frequency, and update the dependent peripherals.
Lexra bus clock frequencies:
- RTL838x: 200MHz
- RTL839x: 200MHz
- RTL930x: 175MHz
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
All current devices use identical bootargs, so let's move that to the
common devicetree includes.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Tested-by: Paul Fertser <fercerpav@gmail.com>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
Recent versions of Realtek's SDK reset both the ethernet NIC and queues
(SW_NIC_RST and SW_Q_RST bits) when initialising the hardware.
Furthermore, when issuing a CPU reset on the Zyxel GS1900-8 (not
supported by any current driver), the networking part of the SoC is not
reset. This leads to unresponsive network after the restart. By
resetting both the ethernet NIC and queues, networking always comes up
reliably.
Suggested-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
This fixes WARNing, missing clocks and
[ 10.422481] bcm_ns_usb2 1800c164.usb2-phy: Clock not defined
Fixes: 5901917b93 ("bcm53xx: use more upsteam DT patches from 5.16 / 5.17")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This fixes:
[ 10.440495] bcm_ns_usb2 1800c000.usb2-phy: can't request region for resource [mem 0x1800c000-0x1800cfff]
[ 10.450039] bcm_ns_usb2 1800c000.usb2-phy: Failed to map DMU regs
[ 10.456183] bcm_ns_usb2: probe of 1800c000.usb2-phy failed with error -16
caused by conflict in allocating resources.
Fixes: f55f1dbaad ("bcm53xx: switch to the kernel 5.10")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
sun6i-rtc cannot be built as a module and the hardware is only
present in some of the sunxi SoCs, see driver source:
{ .compatible = "allwinner,sun6i-a31-rtc" },
{ .compatible = "allwinner,sun8i-a23-rtc" },
{ .compatible = "allwinner,sun8i-h3-rtc" },
{ .compatible = "allwinner,sun8i-r40-rtc" },
{ .compatible = "allwinner,sun8i-v3-rtc" },
{ .compatible = "allwinner,sun50i-h5-rtc" },
{ .compatible = "allwinner,sun50i-h6-rtc" },
Set CONFIG_RTC_DRV_SUN6I=y in kernel config file for cortexa7 and
cortexa53 subtargets which covers all of the above.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
sun6i-rtc is a builtin_platform_driver and cannot be built as a module.
Hence this reverts commit e178d9a549.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Correct ralink_i2s_debugfs_remove declaration in ralink patches when
CONFIG_DEBUG_FS is not selected.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This commit adds support for the Wavlink WL-WN576A2 wall-plug wireles
repeater / router. It is also sold under the name SilverCrest SWV 733 B1.
Device specs:
- CPU: MediaTek MT7628AN
- Flash: 8MB
- RAM: 64MB
- Bootloader: U-Boot
- Ethernet: 1x 10/100 Mbps
- 2.4 GHz: b/g/n SoC
- 5 GHz: a/n/ac MT7610EN
- Buttons: WPS, reset, sliding switch (ap/repeater)
- LEDs: 5x wifi status, 1x LAN/WAN, 1x WPS
Flashing:
U-Boot launches a TFTP client if WPS button is held during boot.
- Server IP: 192.168.10.100
- Firmware file name: firmware.bin
Device will reboot automatically. First boot takes about 90s.
Coelner (waenger@gmail.com) is the original author, but I have made some
fixes. He does not wish to sign off using his real name.
Signed-off-by: Thomas Aldrian <dev.aldrian@gmail.com>
Further devices from the series have been added in the meantime,
introducing `qca955x_dlink_dap-2xxx.dtsi`.
Thus, merge support for DAP-2695 with the existing dtsi.
This implies factory images can now be flashed via the regular
OEM Web UI, as well as the bootloader recovery.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
This device can be merged with the existing dtsi, which declares
the location of ath9k cal-data via devicetree, correcting the 2.4G
mac address in `10_fix_wifi_mac` rather than `10-ath9k-eeprom`.
To make these changes more visible, apply before merging with dtsi.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
This device can be merged with the existing dtsi,
which will increase spi-max-frequency to 50 MHz.
To make this change more visible, increase to 50 MHz before merging.
Signed-off-by: Sebastian Schaper <openwrt@sebastianschaper.net>
The MikroTik LHG 5 series (product codes RBLHG-5nD, RBLHG-5HPnD and
RBLHG-5HPnD-XL) devices are an outdoor 5GHz CPE with a 24.5dBi or 27dBi
integrated antenna built around the Atheros AR9344 SoC.
It is very similar to the SXT Lite5 series which this patch is based
upon.
Specifications:
- SoC: Atheros AR9344
- RAM: 64 MB
- Storage: 16 MB SPI NOR
- Wireless: Atheros AR9340 (SoC) 802.11a/n 2x2:2
- Ethernet: Atheros AR8229 switch (SoC), 1x 10/100 port,
8-32 Vdc PoE in
- 8 user-controllable LEDs:
- 1x power (blue)
- 1x user (white)
- 1x ethernet (green)
- 5x rssi (green)
See https://mikrotik.com/product/RBLHG-5nD for more details.
Notes:
The device was already supported in the ar71xx target.
Flashing:
TFTP boot initramfs image and then perform a sysupgrade. Follow common
MikroTik procedure as in https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Jakob (Jack/XDjackieXD) <jakob@chaosfield.at>
AP6212 wifi need wifi_pwrseq, but from OrangePi Lite 2 dts :
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
clocks = <&rtc 1>;
clock-names = "ext_clock";
reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */
post-power-on-delay-ms = <200>;
};
this pwrseq need rtc clock, or kernel won't find this device.
but now rtc-sunxi.c only support A10/A20.
Orangepi Lite 2 use H6 ,from rtc-sun6i.c show compatible is
{ .compatible = "allwinner,sun6i-a31-rtc" },
{ .compatible = "allwinner,sun8i-a23-rtc" },
{ .compatible = "allwinner,sun8i-h3-rtc" },
{ .compatible = "allwinner,sun8i-r40-rtc" },
{ .compatible = "allwinner,sun8i-v3-rtc" },
{ .compatible = "allwinner,sun50i-h5-rtc" },
{ .compatible = "allwinner,sun50i-h6-rtc" },
So it need this to let kernel find this mmc wifi device.
As suggested by hauke, let it build as package.
Signed-off-by: Zhao Yu <574249312@qq.com>
The MikroTik RouterBOARD wAPR-2nD (wAP R) router features a miniPCI-e
slot with USB lines connected, which are used by some USB cards with
miniPCI-e form factor, like the R11e-LR8. Enabling USB support is
required for such cards to work.
Tested on a MikroTik wAP LR8 kit (RB wAPR-2nD + R11e-LR8).
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
Implement a basic MQPrio support, inserting rules in RX that translate
the TC to prio mapping into vlan prio to queues.
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
Manually rebased:
generic-backport/850-v5.13-usb-ehci-add-spurious-flag-to-disable-overcurrent-ch.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
The crashlog patch as not ported to kernel 5.4.
Fixes: 4e0c54bc5b ("kernel: add support for kernel 5.4")
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
There's no such thing as ucidef_set_interfaces_lan. It's
ucidef_set_interface_lan.
Cc: David Bauer <mail@david-bauer.net>
Signed-off-by: Mark Mentovai <mark@moxienet.com>
bootfs still needs more work before it's ready.
For some unknown reason model RAXE500 uses board id RAX220.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Orange Pi Zero Plus uses a Realtek RTL8211E RGMII Gigabit PHY, but its
currently set to plain RGMII mode meaning that it doesn't introduce
delays.
With this setup, TX packets are completely lost and changing the mode to
RGMII-ID so the PHY will add delays internally fixes the issue.
It looks like this got broken in 5.10 as the PHY RGMII config got fixed
due to datasheet being available and a lot of boards got broken by that.
This has already been sent upstream and received multiple reviews.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This commit contains a series of fixes for DMA. The burst length
patch significantly improves Ethernet performance. Patches were
tested on the xRX200 and xRX330.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Fix mac address increment patch. Permit to overflow to the next
byte and correctly calculate the incremented mac.
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Fixes: d284e6ef0f ("treewide: convert mtd-mac-address-increment* to generic implementation")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Backport of Ansuel Smith's "net: dsa: qca8k: make sure PAD0 MAC06
exchange is disabled", to ensure mac06 is disabled even if enabled by
the bootloader.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
The devicetree property mac-address is expected to be set by the
bootloader and has priority over the nvmem supplied one.
Drop the mac-address address property from the dtsi files, to let the
mac address from nvmem-cells get used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
This patch fixes a blunder of mine. The include needed
for LED_COLOR_ID_BLUE property is missing.
This caused the builds to fail with:
|Error: arch/arm/boot/dts/qcom-ipq4019-r619ac.dtsi:91.13-14 syntax error
|FATAL ERROR: Unable to parse input tree
Fixes: 12d33d388c ("ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0)")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
The Zyxel NBG6617 already uses lzma to compress the kernel.
A local build with every module enabled (either as =Y or =M)
ended produced a 3058 KiB kernel (the kernel partition is 4MiB).
It booted just fine, let's reenable the device.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
P&W R619AC is a IPQ4019 Dual-Band AC1200 router.
It is made by P&W (p2w-tech.com) known as P&W R619AC
but marketed and sold more popularly as G-DOCK 2.0.
Specification:
* SOC: Qualcomm Atheros IPQ4019 (717 MHz)
* RAM: 512 MiB
* Flash: 16 MiB (NOR) + 128 MiB (NAND)
* Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN)
* Wireless:
- 2.4 GHz b/g/n Qualcomm Atheros IPQ4019
- 5 GHz a/n/ac Qualcomm Atheros IPQ4019
* USB: 1 x USB 3.0
* LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED)
* Input: 1 x reset
* 1 x MicroSD card slot
* Serial console: 115200bps, pinheader J2 on PCB
* Power: DC 12V 2A
* 1 x Unpopulated mPCIe Slot (see below how to connect it)
* 1 x Unpopulated Sim Card Slot
Installation:
1. Access to tty console via UART serial
2. Enter failsafe mode and mount rootfs
<https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset>
3. Edit inittab to enable shell on tty console
`sed -i 's/#ttyM/ttyM/' /etc/inittab`
4. Reboot and upload `-nand-factory.bin` to the router (using wget)
5. Use `sysupgrade` command to install
Another installation method is to hijack the upgrade server domain
of stock firmware, because it's using insecure http.
This commit is based on @LGA1150(at GitHub)'s work
<a4932c8d5a>
With some changes:
1. Added `qpic_bam` node in dts. I don't know much about this,
but I observed other dtses have this node.
2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not
working. This fix is from
<51143b4c75>
3. Removed the 32MB NOR variant.
4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes
wlan2g led light up.
5. Added ethphy led config in dts.
6. Changed nand partition label from `rootfs` to `ubi`.
About the 128MiB variant: The stock bootloader sets size of nand to 64MiB.
But most of this devices have 128MiB nand. If you want to use all 128MiB,
you need to modify the `MIBIB` data of bootloader. More details can be
found on github:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060>
For instructions on how to flash the MIBIB partition from u-boot console:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232>
About the Mini PCIe slot: (from "ygleg")
"The REFCLK signals on the Mini PCIe slot is not connected on
this board out of the box. If you want to use the Mini PCIe slot
on the board, you need to (preferably) solder two 0402 resistors:
R436 (REFCLK+) and R444 (REFCLK-)..."
This and much more information is provoided in the github comment:
<https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670>
Signed-off-by: Richard Yu <yurichard3839@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
[Added comment about MIBIB+128 MiB variant. Added commit
message section about pcie slot. Renamed gpio-leds' subnodes
and added color, function+enum properties.]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Similar to mt7623, also no longer use 'blockdev' and stop relying on
in-kernel partition parsers. Instead, strip off all metadata using
'fwtool' while writing the firmware image and scrape the number of
blocks written from 'dd', then use that block offset to stash the
configuration backup.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Re-reading the partition table doesn't work reliably, it fails if
anything on the device is still in use and it's not trivial to prevent
every possible case of a block device still being in use somehow.
Therefore, instead of relying on the in-kernel partition parser to know
where to write the configuration backup, use OpenWrt's format-agnostic
fwtool to strip off all metadata from the image and count its blocks
while writing. In that way we can know where to write the config backup
without needing the kernel to parse the MBR and FIT structures.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
It isn't used anymore so there is no need to hack CPU port. Upstream
(DSA-based) b53 also supports all switch ports just fine.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
This patch never received a proper description and was never sent
upstream as supposed. It was meant to be handled in 2015-2018 so it
should be safe to assume noone really understands it or care.
Cc: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fail if arguments couldn't be parsed and print unrecognized part. It's
important when running it from script with dynamic values. Missing value
could result in skipping argument and silent failures (unexpected its).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
New BCM4908 family based routers will use U-Boot bootloader. That will
require using a totally different firmware format. Kernel has to be put
in a FIT image.
OpenWrt has some helpers for generating .its files but they don't fit
BCM4908 requirements and there is no simple way of extending any of
them. The best solution seems to be storing an .its template.
BCM4908 bootfs may:
1. contain extra binaries (other than kernel & DTB)
2. include multiple DTB files
3. store device specific U-Boot configurations with custom properties
Such setups are too complex to generate using shell script. Raw .its
file on the other hand seems quire clean & reasonable.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Kernel 5.10 grew bigger than 5.4 so we need to bump BZ_TEXT_START to
allow lzma loader hanel its size.
At the same time BZ_STACK_START needs to be increased to avoid
overwriting the stack.
For a reference see:
d5cf4a5aa4 ("brcm47xx: relocate loader to higher address")
2909a4b78e ("brcm47xx: relocate the stack in loader")
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Update config, Makefile and image/Makefile.
Directly switch to kernel 5.10.
This patch was tested in nSIM simulator, no errors appeared.
Signed-off-by: Evgeniy Didin <Evgeniy.Didin@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Paul Spooren <mail@aparcar.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: John Crispin <john@phrozen.org>
Enabling KERNEL_UBSAN exposes several missing symbols. Add new kernel
build options for UBSAN_BOUNDS and UBSAN_TRAP, disable CONFIG_TEST_UBSAN
in the generic kernel configs and enable CONFIG_UBSAN_MISC in generic
5.10 config. The latter symbol was removed in later kernels, as it was
causing some issues, so just disable it in 5.10 instead of adding a
build option for it.
Fixes build failures with KERNEL_UBSAN enabled.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Enabling KERNEL_KASAN exposes several missing symbols. As KASAN_SW_TAGS
is only implemented for arm64 CPUs and requires clang, it doesn't make
sense to make this a build option so just default to KASAN_GENERIC and
disable KASAN_SW_TAGS.
While at it, disable TEST_KASAN_MODULE in the generic 5.10 config.
Fixes build failures with KERNEL_KASAN enabled.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
The qca8k patch series brings the numbering to 799. This patch renames
7xx patches to create space for more backports to be added.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
[rename 729->719]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
After switch to 5.10 kernel, kernel size was too high.
This patch switches Cell-C RTL30VW from uImage to zImage build.
Lzma uImage wrap is required for factory booting and it must left
untouched.
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
This is needed because the HLK-7621 EvB has 32MB of flash,
so it will have to use 4B addressing and the
broken-flash-reset hack has to be used to be able to reboot.
Signed-off-by: Wout Bertrums <wout@wbnet.eu>
[copied github message into commit message]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
It looks like CONFIG_BLK_CMDLINE_PARSER was forgotten during the Orbi
device merge.
So lets refresh the config with it.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
sorting alphabetically default packages
and placing them on their own line.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
[fixed whitespaces before tab, double whitespaces]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Gigabit ethernet adapters using BCM5719/5720 chipset
are common on servers and as easy/cheap to get as
Intel based ones.
Usually found in 2-port and 4-port cards.
Also some devices recently added to x86_64 target
like the Meraki MX100 use this chipset for 8 of
their 12 integrated ports.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Device tree pcie node for this SoC is using different
styles in its different properties. Hence properly
unify them to be able to write a a proper yaml schema
documentation.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210505121736.6459-11-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the YAML schema 'pci-bus.yaml' the 'device_type'
property is mandatory for all pcie root ports. Hence add it.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210506170742.28196-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Property 'bus-range' when values are the default are
not necessary to be defined. Hence, remove all of them.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210506170742.28196-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both 'memc' and 'sysc' nodes are not using 'syscon'
as a node string which is the standard one to be used.
Update both of them.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210505132154.8263-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DT 'ethsys' node is being configured as a syscon
to get access to reset and other registers in the
'mediateķ,mt7621-eth' driver. Since the 'sysc' is also
a syscon, provides the clock and also is virtually
mapped from the same physical address 0x1e000000 we
can just use 'sysc' as the phandle for the syscon in
the ethernet node. Compatible string 'mediatek,mt7621-ethsys'
of the node is not being used anywhere inside the kernel
so, this node can be safely removed.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20210505132154.8263-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was for OpenWrt's swconfig driver, which never made it upstream,
and was also superseded by MT7530 DSA driver.
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Link: https://lore.kernel.org/r/20210108025155.31556-1-dqfext@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'cpc' and 'mc' nodes correspond with the MIPS 'Cluster Power Controller'
and 'MIPS Common Device Memory Map' which are present in some MIPS related
boards. There is already bindings documentation for these two located in:
- Documentation/devicetree/bindings/power/mti,mips-cpc.yaml
- Documentation/devicetree/bindings/bus/mti,mips-cdmm.yaml
Hence, properly update compatible strings and align nodes with already
mainlined bindings documentation. Also, move their definition to a proper
place since both of them are not related with the palmbus at all.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20211002060706.30511-1-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hexadecimal addresses in device tree must be defined using lower case.
There are some of them that are still in upper case. Change them all.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20211017070656.12654-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nodes 'gdma' and 'hsdma' are using magic number '4' in interrupts property.
Use 'IRQ_TYPE_LEVEL_HIGH' instead to align with the rest of the nodes in
the file.
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20211019102915.15409-2-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
converts the still popular WNDR3700 Series to fetch the
caldata through nvmem. As the "MAC with NVMEM" has shown,
there could pitfalls along the way.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Removed upstreamed:
backport-5.4/790-v5.7-net-switchdev-do-not-propagate-bridge-updates-across.patch
All other patches automatically rebased.
Signed-off-by: John Audia <graysky@archlinux.us>
Disable some of the ipq40xx devices due to their kernel size limitations.
These devices fail to build with kernel 5.10 and full buildbot config.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
[keep gl-b1300/gl-s1300 enabled, extend commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There have been enough tests and new developments require the new
kernel, so let's update it.
There is a bunch of devices that do not build anymore due to
kernel size limitations. These are disabled in a subsequent commit.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This adds some essential files required by new 'cortexa7' subtarget,
dedicated for Cortex-A7 based NXP i.MX series. For now, the kernel
config-default focuses only on the i.MX 6UL family, as the following
changeset will introduce support for i.MX 6ULL based device. Support
for more platforms (e.g. i.MX 7) might be enabled later, while adding
more devices.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Modern NXP i.MX series includes several different families, based on
single- or multi-core Arm Cortex-A CPUs. To be able to support more
families within a single target, we split the 'imx' in arch-specific
subtargets, starting with 'cortexa9' for the Cortex-A9 based i.MX 6,
already supported by the original 'imx6' target.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This is first step in migrating to a generic i.MX target which in the
next steps will also get divided into arch-specific subtargets.
In the result, this will make it possible to support, within a single
target, also other modern NXP i.MX families, like the i.MX 7, i.MX 8
or recently introduced i.MX 9.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
This is a minor extension of the commit 26ae69fd03 ("imx6: refresh
kernel config with 5.10 symbols"), with correct and full disable of
the Arm Cortex-A7 based i.MX 6UL and 6UL{L,Z} families support and
re-enable of the Cortex-A9 based i.MX 6L{S,X}.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
U-Boot for the Gateworks Ventana includes filename of the boot script in
the default/embedded environment (see 'include/configs/gw_ventana.h' in
the U-Boot sources).
This restores the old boot script filename ('6x_bootscript-ventana'),
making Ventana boards boot again.
Fixes: 8dba71dd33 ("imx6: image: drop BOOT_SCRIPT and fix DEVICE_NAME")
Reported-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Netgear R6100 is a dual-band Wi-Fi 5 (AC1200) router based on Qualcomm
Atheros (AR9344 + QCA9882) platform. Support for this device was first
introduced in 15f6f67d18 (ar71xx). FCC ID: PY312400225.
Specifications:
- Atheros AR9344 (560 MHz)
- 128 MB of RAM (DDR2)
- 128 MB of flash (parallel NAND)
- 2T2R 2.4 GHz Wi-Fi (AR9344)
- 2T2R 5 GHz Wi-Fi (QCA9882)
- 5x 10/100 Mbps Ethernet (AR9344)
- 4x internal antenna
- 1x USB 2.0 (GPIO-controlled power)
- 6x LED, 3x button (reset, Wi-Fi, WPS)
- UART (4-pin, 2.54 mm pitch) header on PCB
- 1x mechanical power switch
- DC jack for main power input (12 V)
WARNING: sysupgrade from older stable releases is not possible, fresh
installation (via vendor's GUI or TFTP based recovery) is required.
Reason for that is increased kernel partition size.
Installation:
Use the 'factory' image under vendor's GUI or via TFTP U-Boot recovery.
You can use the 'nmrpflash' tool at a boot time, before kernel is loaded
or start it manually by pressing the 'reset' button for ~20 seconds from
powering up the device (U-Boot will start TFTP server on 192.168.1.1,
use TFTP client to send the image).
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
CONFIG_COMPAT_32BIT_TIME is a new symbol and has to be set to avoid:
Provide system calls for 32-bit time_t (COMPAT_32BIT_TIME) [N/y/?] (NEW)
CONFIG_RELOCATABLE needs to be enabled to make kernel start booting.
That raises a question: do we really need CONFIG_EXPERT=y ?
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The boot arguments are copied into the device tree by the boot loader
and taken from the device tree by the kernel.
The code which takes the boot arguments from the different sources was
reworked with kernel 5.5.
We have to activate CONFIG_MIPS_CMDLINE_DTB_EXTEND to take the boot
arguments from the device tree.
This makes the system boot on the board again.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Make the patches apply on kernel 5.10 and refresh the patches and the
kernel configuration on top of kernel 5.10.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The pistachio U-Boot expects a default configuration with the name
config@1 in the FIT image. The default was changed in OpenWrt some
months ago.
This makes the board boot again.
Fixes: 9f714398e0 ("build: use config-1 instead of config@1 as default")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
I had quite a hard time to understand what the change to net/core/dev.c
is supposed to do.
Simplify the change by returning NETDEV_TX_OK in case a eth_mangle_tx
callback was set but returned NULL instead of setting the return value
in the else branch.
Signed-off-by: Mathias Kresin <dev@kresin.me>
ar8216 switches have a hardware bug, which renders normal 802.1q support
unusable. Packet mangling is required to fix up the vlan for incoming
packets.
The patch was ommited at the time kernel 5.10 support was added but is
still required for ar8216 switches.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Add the latest default Kernel for testing. This step is required to keep
UML in tree for the next release.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The UML target been outdated for a long time. Instead of just carrying
unmaintained code we should build it again and allow people and CIs to
use it for testing.
This commit removes the `source-only` feature which disables building.
Signed-off-by: Paul Spooren <mail@aparcar.org>
This step drops support host build systems other than x86/64 to allow
two Kernel configuration in parallel. With this commit the setup follow
the config style of all other targets.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The current `uml` README is terribly outdated and non of the examples
work by default. Fix that and while at it convert it to Markdown.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Don't patch the kernel to expose the partition name in sysfs as it is
already exposed via 'uevent'.
All previous users have been converted to use 'uevent', so we can
safely drop the custom patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use find_mmc_part instead of previously introduced
get_partition_by_name which requires a custom kernel patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Use find_mmc_part instead of previously introduced
get_partition_by_name which requires a custom kernel patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Netgear SRS60 and SRR60 (sold together as SRK60) are two almost
identical AC3000 routers. The SRR60 has one port labeled as wan while
the SRS60 not. The RBR50 and RBS50 (sold together as RBK50) have a
different external shape but they have an USB 2.0 port on the back.
This patch has been tested only on SRS60 and RBR50, but should work
on SRR60 and RBS50.
Hardware
--------
SoC: Qualcomm IPQ4019 (717 MHz, 4 cores 4 threads)
RAM: 512MB DDR3
FLASH: 4GB EMMC
ETH:
- 3x 10/100/1000 Mbps Ethernet
- 1x 10/100/1000 Mbps Ethernet (WAN)
WIFI:
- 2.4GHz: 1x IPQ4019 (2x2:2)
- 5GHz: 1x IPQ4019 (2x2:2)
- 5GHz: 1x QCA9984 (4x4:4)
- 6 internal antennas
BTN:
- 1x Reset button
- 1x Sync button
- 1x ON/OFF button
LEDS:
- 8 leds controlled by TLC59208F (they can be switched on/off
independendently but the color can by changed by GPIOs)
- 1x Red led (Power)
- 1x Green led (Power)
UART:
- 115200-8-N-1
Everything works correctly.
Installation
------------
These routers have a dual partition system. However this firmware works
only on boot partition 1 and the OEM web interface will always flash on
the partition currently not booted.
The following steps will use the SRS60 firmware, but you have to chose
the right firmware for your router.
There are 2 ways to install Openwrt the first time:
1) Using NMRPflash
1. Download nmrpflash (https://github.com/jclehner/nmrpflash)
2. Put the openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img
file in the same folder of the nmrpflash executable
3. Connect your pc to the router using the port near the power button.
4. Run "nmrpflash -i XXX -f openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img".
Replace XXX with your network interface (can be identified by
running "nmrpflash -L")
5. Power on the router and wait for the flash to complete. After about
a minute the router should boot directly to Openwrt. If nothing
happens try to reboot the router. If you have problems flashing
try to set "10.164.183.253" as your computer IP address
2) Without NMRPflash
The OEM web interface will always flash on the partition currently not
booted, so to flash OpenWrt for the first time you have to switch to
boot partition 2 and then flash the factory image directly from the OEM
web interface.
To switch on partition 2 you have to enable telnet first:
1. Go to http://192.168.1.250/debug.htm and check "Enable Telnet".
2. Connect through telent ("telnet 192.168.1.250") and login using
admin/password.
To read the current boot_part:
artmtd -r boot_part
To write the new boot_part:
artmtd -w boot_part 02
Then reboot the router and then check again the current booted
partition
Now that you are on boot partition 2 you can flash the factory Openwrt
image directly from the OEM web interface.
Restore OEM Firmware
--------------------
1. Download the stock firmware from official netgear support.
2. Follow the nmrpflash procedure like above, using the official
Netgear firmware (for example SRS60-V2.2.1.210.img)
nmrpflash -i XXX -f SRS60-V2.2.1.210.img
Notes
-----
1) You can check and edit the boot partition in the Uboot shell using
the UART connection.
"boot_partition_show" shows the current boot partition
"boot_partition_set 1" sets the current boot partition to 1
2) Router mac addresses:
LAN XX:XX:XX:XX:XX:69
WAN XX:XX:XX:XX:XX:6a
WIFI 2G XX:XX:XX:XX:XX:69
WIFI 5G XX:XX:XX:XX:XX:6b
WIFI 5G (2nd) XX:XX:XX:XX:XX:6c
LABEL XX:XX:XX:XX:XX:69
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
[added 5.10 changes for 901-arm-boot-add-dts-files.patch, moved
sysupgrade mmc.sh to here and renamed it, various dtsi changes]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
CONFIG_CMDLINE_PARTITION:
Some devices with mmc like the Netgear Orbi Pro SRS60 or Netgear Orbi
RBR50 needs to hardcode the partitions layout in the cmdline boot
correctly
CONFIG_LEDS_TLC591XX:
This is needed for the led driver found in the Netgear Orbi Pro SRS60
Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Shang Jia <jiash416@gmail.com>
[added 5.10 config]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Backport the patch queued upstream for 5.16. The patch differs slightly
from the upstream patch due to an upstream change that added a
convenience function.
Signed-off-by: Sander Vanheule <sander@svanheule.net>
It seems like sleep_clk was copied from ipq806x.
Fix ipq40xx sleep_clk to the value QSDK defines.
Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [5.4+5.10]
This patch changes the default network configuration
to fetch the IP addresses over dhcp instead of being
statically assigned.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
GPIOs on the Aircube AC are wrong:
- Reset GPIO moved from 17 to 12
- PoE Pass Through GPIO for Aircube AC is 3
Fixes: 491ae3357e ("ath79: add support for Ubiquiti airCube AC")
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
Specifications:
SOC: QCA9531 650 MHz
ROM: 16 MiB Flash (Winbond W25Q128FV)
RAM: 128 MiB DDR2 (Winbond W971GG6SB)
LAN: 10/100M *2
WAN: 10/100M *1
LED: BGR color *1
Mac address:
label C8:0E:77:xx:xx:68 art@0x0
lan C8:0E:77:xx:xx:62 art@0x6
wan C8:0E:77:xx:xx:68 art@0x0 (same as the label)
wlan C8:0E:77:xx:xx:B2 art@0x1002 (load automatically)
TFTP installation:
* Set local IP to 192.168.67.100 and open tftpd64, link lan
port to computer.
Rename "xxxx-factory.bin" to
"openwrt-ar71xx-generic-ap147-16M-rootfs-squashfs.bin".
* Make sure firmware file is in the tftpd's directory, push
reset button and plug in, hold it for 5 seconds, and then
it will download firmware from tftp server automatically.
More information:
* This device boot from flash@0xe80000 so we need a okli
loader to deal with small kernel partition issue. In order
to make full use of the storage space, connect a part of the
previous kernel partition to the firmware.
Stock Modify
0x000000-0x040000(u-boot) 0x000000-0x040000(u-boot)
0x040000-0x050000(u-boot-env) 0x000000-0x050000(u-boot-env)
0x050000-0xe80000(rootfs) 0x050000-0xe80000(firmware part1)
0xe80000-0xff0000(kernel) 0xe80000-0xe90000(okli-loader)
0xe90000-0xff0000(firmware part2)
0xff0000-0x1000000(art) 0xff0000-0x1000000(art)
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Dongwon T&I DW02-412H is a 2.4/5GHz band 11ac (WiFi-5) router, based on
Qualcomm Atheros QCA9557.
Specifications
--------------
- SoC: Qualcomm Atheros QCA9557-AT4A
- RAM: DDR2 128MB
- Flash: SPI NOR 2MB (Winbond W25Q16DVSSIG / ESMT F25L16PA(2S)) +
NAND 64/128MB
- WiFi:
- 2.4GHz: QCA9557 WMAC
- 5GHz: QCA9882-BR4A
- Ethernet: 5x 10/100/1000Mbps
- Switch: QCA8337N-AL3C
- USB: 1x USB 2.0
- UART:
- JP2: 3.3V, TX, RX, GND (3.3V is the square pad) / 115200 8N1
Installation
--------------
1. Connect a serial interface to UART header and
interrupt the autostart of kernel.
2. Transfer the factory image via TFTP and write it to the NAND flash.
3. Update U-Boot environment variable.
> tftpboot 0x81000000 <your image>-factory.img
> nand erase 0x1000000
> nand write 0x81000000 0x1000000 ${filesize}
> setenv bootpart 2
> saveenv
Revert to stock firmware
--------------
1. Revert to stock U-Boot environment variable.
> setenv bootpart 1
> saveenv
MAC addresses as verified by OEM firmware
--------------
WAN: *:XX (label)
LAN: *:XX + 1
2.4G: *:XX + 3
5G: *:XX + 4
The label MAC address was found in art 0x0.
Credits
--------------
Credit goes to the @manatails who first developed how to port OpenWRT
to this device and had a significant impact on this patch.
And thanks to @adschm and @mans0n for guiding me to revise the code
in many ways.
Signed-off-by: Jihoon Han <rapid_renard@renard.ga>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Sungbo Eo <mans0n@gorani.run>
This fixes support for Dongwon T&I DW02-412H which uses F25L16PA(2S) flash.
Signed-off-by: Jihoon Han <rapid_renard@renard.ga>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
[refresh patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently, we are overriding the bootloader provided MAC-s as the ethernet
aliases are reversed so MAC-s were fixed up in userspace.
There is no need to do that as we can just fix the aliases instead and get
rid of MAC setting via userspace helper.
Fixes: 59f0a0f ("ipq806x: add Edgecore ECW5410 support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
ECW5410 has 2 QCA9984 cards, one per PCI controller.
They are located at PCI adresses 0001:01:00.0 and 0002:01:00.0.
Currently, pre-cal is not provided for 0001:01:00.0 at all,but for
0000:01:00.0 which is incorrect and causes the ath10k driver to not
be able to fetch the BMI ID and use that to fetch the proper BDF but
rather fail with:
[ 12.029708] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46.
[ 12.031816] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142)
[ 12.037660] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0
[ 13.173898] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe
[ 13.174015] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
[ 13.189304] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc35
[ 15.492322] ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0046,subsystem-vendor=168c,subsystem-device=cafe,variant=Edgecore-ECW541 from ath10k/QCA9984/hw1.0/board-2.bin
[ 15.543883] ath10k_pci 0001:01:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9984/hw1.0
[ 15.543920] ath10k_pci 0001:01:00.0: failed to fetch board file: -12
[ 15.552281] ath10k_pci 0001:01:00.0: could not probe fw (-12)
So, provide the pre-cal for the actual PCI card and not the non-existent
one.
Fixes: 59f0a0f ("ipq806x: add Edgecore ECW5410 support")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
It looks like this is a leftover before there was a proper MDIO driver.
Since both PHY-s are connected to the HW MDIO bus there is no reason for
this to exist anymore, especially since it uses the same pins as the HW
controller and has the pinmux for the set to "MDIO" so this worked by
pure luck as GPIO MDIO would probe first and override the HW driver.
Move the GMAC3 to simply use the same MDIO bus phandle.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
This changes the image generation to use a unique directory. With
parallel building it may occur that two concurrent jobs try
to create an image which leds to errors. It also removes a needless
subdirecory.
Signed-off-by: André Valentin <avalentin@marcant.net>
Specifications:
- SoC: MediaTek MT7621AT
- RAM: 256 MB (DDR3)
- Flash: 32 MB SPI NOR 44MHz
- Switch: 1 WAN, 4 LAN (Gigabit)
- LEDs: 1 WAN, 4 LAN (controlled by PHY)
- USB Ports: 1 x USB2, 1 x USB3
- WLAN: 1 x 2.4, 5 GHz 866Mbps (MT7612E)
- Button: 1 button (reset)
- UART Serial: UART1 as console : 57600 baud
- Power: 12VDC, 1A
Installation:
Update openWRT firmware using internal GNUBEE uboot:
https://github.com/gnubee-git/GnuBee-MT7621-uboot
By HTTP: Initial uboot address is http://10.10.10.123, your address
needs to be 10.10.10.x, and mask 255.255.255.0.
By TFTP: Uboot is in client mode, the address of the firmware must
be tftp://10.10.10.3/uboot.bin
Recovery:
Manufacturer provides MTK OpenWrt 14.07 source code, compile then
flash it by uboot.
HLK-7621A is a stamp hole package module for embedded development,
users have to design IO boards to use it.
MAC addresses:
- u-boot-env contains a placeholder address:
> mtd_get_mac_ascii u-boot-env ethaddr
03:17:73🆎cd:ef
- phy0 gets a valid-looking address:
> cat /sys/class/ieee80211/phy0/macaddress
f8:62:aa:**:**:a8
- Calibration data for &pcie2 contains a valid address, however the
zeros in the right half look like it's not real:
8c:88:2b:00:00:1b
- Since it's an evaluation board and there is no solid information
about the MAC address assignment, the ethernet MAC address is left random.
Signed-off-by: Chen Yijun <cyjason@bupt.edu.cn>
[add keys and pcie nodes to properly support evaluation board]
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
[remove ethernet address, wrap lines properly]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit adds support for Xiaomi MiWiFi 3C device.
Xiaomi MiWifi 3C has almost the same system architecture
as the Xiaomi Mi WiFi Nano, which is already officially
supported by OpenWrt.
The differences are:
- Numbers of antennas (4 instead of 2). The antenna management
is done via the µC. There is no configuration needed in the
software code.
- LAN port assignments are different. LAN1 and WAN are
interchanged.
OpenWrt Wiki: https://openwrt.org/toh/xiaomi/mir3c
OpenWrt developers forum page:
https://forum.openwrt.org/t/support-for-xiaomi-mi-3c
Specifications:
- CPU: MediaTek MT7628AN (575MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LED: 1x amber/blue/red. Programmable
- Button: Reset
MAC addresses as verified by OEM firmware:
use address source
LAN *:92 factory 0x28
WAN *:92 factory 0x28
2g *:93 factory 0x4
OEM firmware uses VLAN's to create the network interface for WAN and LAN.
Bootloader info:
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader start OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".
How to install:
1- Use OpenWRTInvasion to gain telnet, ssh and ftp access.
https://github.com/acecilia/OpenWRTInvasion
(IP: 192.168.31.1 - Username: root - Password: root)
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0".
Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin
to /tmp in router using ftp.
5- Enable UART access and change start image for OS1.
```
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
```
6- Installing Openwrt on OS1 and free OS2.
```
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin OS1
```
Limitations: For the first install the image size needs to be less
than 7733248 bits.
Thanks for all community and especially for this device:
minax007, earth08, S.Farid
Signed-off-by: Eduardo Santos <edu.2000.kill@gmail.com>
[wrap lines, remove whitespace errors, add mediatek,mtd-eeprom to
&wmac, convert to nvmem]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch enables the SFP cage on the MikroTik RouterBOARD 921GS-5HPacD
(mANTBox 15s).
The RB922UAGS-5HPacD had it already working, so the support code is
moved to the common DTSI file both devices share.
Tested on a RouterBOARD 921GS-5HPacD with a MikroTik S-53LC20D module.
Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
LED labels for this device are different in 01_leds file and in device
DTS. Switch to DT triggers, which works on Telewell TW-4 (LTE) clone
device.
This has not been tested on the LR-25G001 itself, just on the clone
mentioned above.
Fixes: 20b09a2125 ("ramips: add support for Lava LR-25G001")
Signed-off-by: Jani Partanen <rtfm@iki.fi>
[rephrase commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
After the ath10k_patch_mac lines have been removed, a lot of blocks
can be consolidated.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The out-of-tree qcom-smem patches traditionally displayed mtd partition names
in upper case, starting with the new mainline qcom-smem support in kernel v5.10,
it switched to normalizing the partition names to lower case.
While both 5.4 and 5.10 were supported in the target, we carried a workaround
to support both of them. Since the target has dropped 5.4 recently, those
can be removed now.
Ref:
2db9dded0a ("ipq806x: nbg6817: case-insensitive qcom-smem partitions")
435dc2e77e ("ipq806x: ecw5410: case-insensitive qcom-smem partitions")
f70e11cd97 ("ipq806x: g10: case-insensitive qcom-smem partitions")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Use nvmem framework for supported mac-address stored
in nvmem cells and drop mac patch function for hotplug
script for supported devices.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
[rebase, move to correct node for d7800, include xr500]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specs (same as in v1):
- MT7628AN (575 MHz)
- 64MB RAM
- 8MB of flash (SPI NOR)
- 1x 10/100Mbps Ethernet (MT7628AN built-in switch with vlan)
- 1x 2.4GHz wifi (MT7628AN)
- 1x 5Ghz wifi (MT7612E)
- 4x LEDs (5 GPIO-controlled)
- 1x reset button
- 1x WPS button
The only and important difference between v1 & v3 is in flash memory
layout, so pls don't interchange these 2 builds!
Installation through web-ui (on OEM factory firmware):
1. Visit http://tplinkrepeater.net or the configured IP address of
your RE305 v3 (default 192.168.0.254).
2. Log in with the password you've set during initial setup of the
RE305 (there is no default password).
3. Go to Settings -> System Tools -> Firmware upgrade
4. Click Browse and select the OpenWRT image with factory.bin suffix
(not sysupgrade.bin)
5. A window with a progress bar will appear. Wait until it completes.
6. The RE305 will reboot into OpenWRT and serve DHCP requests on the
ethernet port.
7. Connect an RJ45 cable from the RE305 to your computer and access
LuCI at http://192.168.1.1/ to configure (or use ssh).
Disassembly:
Just unscrew 4 screws in the corners & take off the back cover.
Serial is exposed to the right side of the main board (in the middle)
and marked with TX/RX/3V3/GND, but the holes are filled with solder.
Installation through serial:
1. connect trough serial (1n8, baudrate=57600)
2. setup the TFTP server and connect it via ethernet
(ipaddr=192.168.0.254 of device, serverip=192.168.0.184 - your pc)
3. boot from a initramfs image first (choose 1 in the bootloader
options)
4. test it a bit with that, then proceed to run sysupgrade build
MAC addresses as verified by OEM firmware:
use OpenWrt address reference
LAN eth0 *:d2 label
2g wlan0 *:d1 label - 1
5g wlan1 *:d0 label - 2
The label MAC address can be found in config 0x2008.
Signed-off-by: Michal Kozuch <servitkar@gmail.com>
[redistribute WLAN node properties between DTS/DTSI, remove
compatible on DTSI, fix indent/wrapping, split out firmware-utils
change]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ELECOM WRC-X3200GST3 uses the same header/footer as WRC-GS/GST devices
in ramips/mt7621 subtarget, so move "Build/elecom-wrc-gs-factory" to
image-commands.mk to use from mediatek/mt7622 subtarget.
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Specification:
CPU: Allwinner H5, Quad-core Cortex-A53
DDR3 RAM: 512MB
Network: 10/100/1000M Ethernet x 2
USB Host: Type-A x 1
MicroSD Slot x 1
MicroUSB: for power input
Debug Serial Port: 3Pin pin-header
LED: WAN, LAN, SYS
KEY: Reset
Power Supply: DC 5V/2A
Installation:
Write the image to SD Card with dd.
Note:
1. OpenWrt currently does not support LED_FUNCTION, change back to the
previous practice (Consistent with NanoPi R1).
2. Since the upstream commit https://github.com/torvalds/linux/bbc4d71
("net: phy: realtek: fix rtl8211e rx/tx delay config"), we need to
change the phy-mode from rgmii to rgmii-id.
So set phy-mode for 5.4 and 5.10 respectively.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Deleted (upstreamed):
bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch [1]
Manually rebased:
bcm27xx/patches-5.10/950-0355-xhci-quirks-add-link-TRB-quirk-for-VL805.patch
bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
Note: although automatically rebaseable, the last patch has been edited to avoid
conflicting bit definitions.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=b6f32897af190d4716412e156ee0abcc16e4f1e5
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Back in the day, the board-2.bin came with ath10k-firmware-qca4019.
This changed with
commit c3b2efaf24 ("linux-firmware: ath10k: add board firmware packages")
which placed the board-2.bin into a separate package: ath10k-board-qca4019.
This was great, because it addressed one of the caveat of the original
ipq-wifi package:
commit fa03d441e9 ("firmware: add custom IPQ wifi board definitions")
| 2. updating ath10k-firmware-qca4019 will also replace
| the board-2.bin. For this cases the user needs to
| manually reinstall the wifi-board package once the
| ath10k-firmware-qca4019 is updated.
This could be extended further so that ipq-wifi packages
no longer use "install-override" and the various QCA4019
variants list the ath10k-board-qca4019 as a CONFLICT
package.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
OpenWrt maintains two special out-of-tree DT properties:
"qca,disable-5ghz" and "qca,disable-2ghz". These are implemented
in a mac80211 ath9k patch "550-ath9k-disable-bands-via-dt.patch".
With the things being what they are, now might be a good
point to switch the devices to the generic and upstream
"ieee80211-freq-limit" property. This property is much
broader and works differently. Instead of disabling the
drivers logic which would add the affected band and
channels. It now disables all channels which are not
within the specified frequency range.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # HH5A
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Commit 03e1d93e07 ("realtek: add driver support for routing
offload") added routing offload for IPv4, but broke IPv6 routing
completely. The routing table is empty and cannot be updated:
root@gs1900-10hp:~# ip -6 route
root@gs1900-10hp:~# ip -6 route add unreachable default
RTNETLINK answers: Invalid argument
As a side effect, this breaks opkg on IPv4 only systems too,
since uclient-fetch fails when there are no IPv6 routes:
root@gs1900-10hp:~# uclient-fetch http://192.168.99.1
Downloading 'http://192.168.99.1'
Failed to send request: Operation not permitted
Fix by returning NOTIFY_DONE when offloading is unsupported, falling
back to default behaviour.
Fixes: 03e1d93e07 ("realtek: add driver support for routing offload")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
The current rule produces empty trailers, causing the OEM firmware
update application to reject our images.
The double expansion of a makefile variable does not work inside
shell code. The second round is interpreted as a shell expansion,
attempting to run the command ZYXEL_VERS instead of expanding the
$(ZYXEL_VERS) makefile variable.
Fix by removing one level of variable indirection.
Fixes: c6c8d597e1 ("realtek: Add generic zyxel_gs1900 image definition")
Tested-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
During review of the MR32, Florian Fainelli pointed out that the
SoC has a real I2C-controller. Furthermore, the connected pins
(SDA and SCL) would line up perfectly for use. This patch swaps
out the the bitbanged i2c-gpio with the real deal.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Deselect CONFIG_VIDEO_SUN6I_CSI Kconfig symbol for now. If anyone wants
to use CSI (camera interface) they should package the kernel module.
After this change, sunxi targets build again.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This switches pinctrl driver to use the old & good DT binding. There is
no more need to adjust upstream DTS file.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Simply disable this for now, if anyone wants to use CSI feel free to
package it as a kernel module package.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
In case of the block device still being in use, re-reading the
partition table fails. In that case, abort sysupgrade to avoid
corrupting the just-written image because of wrong offsets caused
by failure to re-read the partition table.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds support for the Netgear Nighthawk Pro Gaming XR500.
It is the successor to the Netgear Nighthawk R7800 and shares almost
identical hardware to that device.
The stock firmware is a heavily modified version of OpenWRT.
Specifications:
SoC: Qualcomm Atheros IPQ8065
RAM: 512 MB
Storage: 256 MiB NAND Flash
Wireless: 2x Qualcomm Atheros QCA9984
Ethernet: 2x 1000/100/10 dedicated interfaces
Switch: 5x 1000/100/10 external ports
USB: 2x 3.0 ports
More information:
Manufacturer page: https://www.netgear.com/gaming/xr500/
Almost identical to Netgear R7800
Differences (r7800 > xr500):
Flash: 128MiB > 256MiB
Removed esata
swapped leds:
usb1 (gpio 7 > 8)
usb2 (gpio 8 > 26)
guest/esata (gpio 26 > 7)
MAC addresses:
On the OEM firmware, the mac addresses are:
WAN: *:50 art 0x6
LAN: *:4f art 0x0 (label)
2G: *:4f art 0x0
5G: *:51 art 0xc
Installation:
Install via Web Interface (preferred):
Utilize openwrt-ipq806x-netgear_xr500-squashfs-factory.img
Install via TFTP recovery:
1.Turn off the power, push and hold the reset button (in a hole on
backside) with a pin
2.Turn on the power and wait till power led starts flashing white
(after it first flashes orange for a while)
3.Release the reset button and tftp the factory img in binary mode.
The power led will stop flashing if you succeeded in transferring
the image, and the router reboots rather quickly with the new
firmware.
4.Try to ping the router (ping 192.168.1.1). If does not respond,
then tftp will not work either.
Uploading the firmware image with a TFTP client
$ tftp 192.168.1.1
bin
put openwrt-ipq806x-netgear_xr500-squashfs-factory.img
Note:
The end of the last partition is at 0xee00000. This was chosen
by the initial author, but nobody was able to tell why this
particular arbitrary size was chosen. Since it's not leaving
too much empty space and it's the only issue left, let's just
keep it for now.
Based on work by Adam Hnat <adamhnat@gmail.com>
ref: https://github.com/openwrt/openwrt/pull/3215
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
[squash commits, move common LEDs to DTSI, remove SPDX on old
files, minor whitespace cleanup, commit message facelift,
add MAC address overview, add Notes, fix MAC addresses,
use generic name for partition nodes in DTS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Allow RAM size to be passed thru U-Boot. There are 128MB and 64MB
versions of Minew G1-C. This is also in line with the behaviour of
most other RAMIPS boards.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Compile tested and run tested on Pine64+.
Acked-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Add support for SAM9X60-EK board.
Hardware:
- SoC: SAM9X60
- RAM: Winbond W972GG6KB-25 (2Gbit DDR2)
- NAND Flash: Micron MT29F4G08ABAEA
- QSPI Flash: Microchip SST26VF064B
- EEPROM: Microchip 24AA02E48
- SDMMC: One standard 4-bit SD card interface
- USB: two stacked Type-A connectors with power switches, one micro-B
USB device
- CAN: 2 interfaces (Microchip MCP2542)
- Ethernet: one 10/100Mbps
- WiFi/BT: one optional WiFi/Bluetooth interface
- Audio: one ClassD port
- Display: one 24-bit LCD interface
- Camera: one 12-bit image sensor interface
- IO: one IO expander (Microchip MCP23008)
- Debug ports: one J-Link-OB + CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: 4 push button switches
- Expansion: one PIO connector, one mikrobus connector
- Power management: two power regulators, two power consumption measurement
devices
Flashing:
- follow the procedure at [1]
[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sam9x60EKMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add support for SAMA5D27 WLSOM1-EK board.
Hardware:
- SIP: SAMA5D27C-LD2G-CU including SAMA5D27 MPU and 2Gbit LPDDR2-SDRAM
- MMC: one standard SD card interface
- Flash: 64 Mb serial quad I/O flash memory (SST26VF064BEUIT-104I/MF)
with embedded EUI-48 and EUI-64 MAC addresses
- USB: one USB device, one USB host one HSIC interface
- Ethernet: 1x10/100Mbps port
- WiFi/BT: IEEE 802.11 b/g/n Wi-Fi plus Bluetooth (Wi-Fi/BT) module
(ATWILC3000-MR110UA)
- Crypto: one ATECC608B-TNGTLS secure element
- Video: one LCD RGB 18-bit interface, one ISC 12-bit camera interface
- Debug port: one JTAG interface, one UART interface, one WILC UART
interface
- Leds: one RGB LED
- Buttons: start, reset, wakeup, user buttons
- Expansion: one tamper connector, one mikrobus interface, 2 XPRO PTC
connector
- Power managament: PMIC (MCP16502)
Flashing:
- follow procedure at [1]
[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d27WLSom1EKMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add support for SAMA5D2 ICP board.
Hardware:
- SoC: SAMA5D27
- RAM: 512 MB DDR3L
- MMC: One stanard SD card interface
- USB: One USB host switch 4 ports with power switch,
One USB device type Micro-AB
- CAN: 2 interfaces
- Ethernet: One Gigabit Ethernet PHY through HSIC,
One ETH switchport,
One EtherCAT interface
- WiFi/BT: Footprint for IEEE 802.11 b/g/n Wi-Fi plus
Bluetooth module (Wi-Fi/BT), suitable for
Microchip WILC3000-MR110CA or WILC3000-MR110UA
- Debug port: One J-Link-OB/J-Link-CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: reset, wakeup, 2 user buttons
- Expansion: one PIOBU/PIO connector, 3 mikrobus sockets
- Power mangament: PMIC (MCP16502), one power consumption device
(PAC1934)
Not working in Linux:
- EtherCAT interface: there is no Linux support integrated
- PAC1934: driver available at [1] but not integrated in Linux
Flashing:
- follow the procedure at [2]
[1] https://ww1.microchip.com/downloads/en/DeviceDoc/pac193x_linux_driver.zip
[2] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d2IcpMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Bump at91 targets to kernel v5.10. With this patches and files for
wb45n and wb50n were removed as they are now included in upstream
kernel. Along with:
- this the kernel config for sama5d2 and sam9x targets has been
refreshed (with make kernel_menuconfig + save);
- CONFIG_ARCH_AT91 and specific sam9x SoCs (AT91RM9200, AT91SAM9,
SAM9X60) has been enabled such that sam9x SoCs to be able to boot.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Enable the sun8i-thermal driver to allow reading the
temperature of the SoC.
As suggested by mans0n, disable this driver in the
a8 subtarget because it does not support yet.
Tested on NanoPi R1S H5.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Tidy qca8k_setup for loops relating to port handling. No functional
changes.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Add cpu_port_index fix to apply settings to correct CPU port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Backport Ansuel Smith's various qca8k feature additions:
- mac-power-sel support
- SGMII PLL explicit enable
- tx/rx clock phase to falling edge
- power-on-sel and LED open drain mode
- cpu port 6
- qca8328 support
- sgmii internal delay
- move port config to dedicated struct
- convert to yaml schema
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Backport workaround for QCA8327 PHY resume, which does not properly support
genphy_suspend/resume. Also add DAC amplitude fix for the QCA8327 PHY,
set port to preferred master and add proper names to debug regs.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
This commit add accepted upstream patches that improve & tidy qca83xx support.
1 - Split qca8327 to A & B variants, identifiable by phy_id
2 - Add suspend/resume support to qca8xx phys
3 - Tidy spacing and phy naming.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Add support for qca8327 internal phy needed for correct init of the
switch port. It does use the same qca8337 function and reg just with a
different id.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Backport fixes including:
net: dsa: qca8k: fix missing unlock on error in qca8k_vlan_(add|del)
net: dsa: qca8k: check return value of read functions correctly
net: dsa: qca8k: add missing check return value in qca8k_phylink_mac_config()
net: dsa: qca8k: fix an endian bug in qca8k_get_ethtool_stats()
net: dsa: qca8k: check the correct variable in qca8k_set_mac_eee()
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
This is a backport of Ansuel Smith's "Multiple improvement to qca8k stability"
series. The QCA8337 switch is available on multiple platforms including
ipq806x, ath79 and bcm53xx.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
Rosen reported strange dtc warnings that had their origin in
an upstream patch to 5.8-rc1. Upon further digging this
revealed an ongoing thread [0] discussing the topic:
> [...]I don't think we need a bunch of warning fix patches to add
> these everywhere. Also, the need for #address-cells pretty much makes
> no sense on any modern system. It is a relic from days when the bus
> (address) topology and interrupt topology were related.
and later on:
> So really, we only need to be checking for #address-cells in nodes
> with interrupt-map.
This patch backports just the patch which removed the warning message
(this is from the upstream dtc project [1] - but not the kernel).
the patch does not add the checking of the #address-cells in nodes
with interrupt-map.
[0] <https://lore.kernel.org/linux-devicetree/91e3405245c89f134676449cf3822285798d2ed2.1612189652.git.michal.simek@xilinx.com/>
[1] <https://git.kernel.org/pub/scm/utils/dtc/dtc.git/commit/?id=d8d1a9a77863a8c7031ae82a1d461aa78eb72a7b>
Link: <https://github.com/openwrt/openwrt/pull/4685>
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
