These devices do not use rgmii2 as gpio, therefore remove rgmii2 pin group
from state-default. Remove overwriting the ethernet node for these devices.
Move claiming the rgmii2 group from mt7621_zyxel_nwa-ax.dtsi to
mt7621_zyxel_nwa50ax.dts as it's only the latter using rgmii2 pins as gpio.
Remove duplicate ethernet overwrite from mt7621_tplink_archer-x6-v3.dtsi.
Claim rgmii2 group as gpio on mt7621_bolt_arion.dts as it uses an rgmii2
pin, 26, as gpio.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Add the missing pinctrl properties on the ethernet node.
GMAC1 will start working with this change.
Link: https://lore.kernel.org/netdev/83a35aa3-6cb8-2bc4-2ff4-64278bbcd8c8@arinc9.com/
Overwrite pinctrl-0 property without rgmii2_pins on devicetrees which use
the rgmii2 pins as GPIO (22 - 33).
Give gpio function to rgmii2 pin group on mt7621_tplink_archer-x6-v3.dtsi
which uses GPIO 28.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Define nvmem-cells and convert mtd-mac-address to nvmem implementation.
The conversion is done with an automated script.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
The patch adds support for the TP-Link Archer C6 v3 (FCC ID TE7A6V3)
The patch adds identification changes to the existing TP-Link Archer A6,
by Vinay Patil <post2vinay@gmail.com>, which has identical hardware.
Specification
-------------
MediaTek MT7621 SOC
RAM: 128MB DDR3
SPI Flash: W25Q128 (16MB)
Ethernet: MT7530 5x 1000Base-T
WiFi 5GHz: Mediatek MT7613BE
WiFi 2.4GHz: Mediatek MT7603E
UART/Serial: 115200 8n1
Device Configuration & Serial Port Pins
---------------------------------------
ETH Ports: LAN4 LAN3 LAN2 LAN1 WAN
_______________________
| |
Serial Pins: | VCC GND TXD RXD |
|_____________________|
LEDs: Power Wifi2G Wifi5G LAN WAN
Build Output
------------
The build will generate following set of files
[1] openwrt-ramips-mt7621-tplink_archer-c6-v3-initramfs-kernel.bin
[2] openwrt-ramips-mt7621-tplink_archer-c6-v3-squashfs-factory.bin
[3] openwrt-ramips-mt7621-tplink_archer-c6-v3-squashfs-sysupgrade.bin
How to Use - Flashing from TP-Link Web Interface
------------------------------------------------
* Go to "Advanced/System Tools/Firmware Update".
* Click "Browse" and upload the OpenWrt factory image: factory.bin[2]
* Click the "Upgrade" button, and select "Yes" when prompted.
TFTP Booting
------------
Setup a TFTP boot server with address 192.168.0.5.
While starting U-boot press '4' key to stop autoboot.
Copy the initramfs-kernel.bin[1] to TFTP server folder, rename as test.bin
From u-boot command prompt run tftpboot followed by bootm.
Recovery
--------
Archer A6 V3 has recovery page activated if SPI booting from flash fails.
Recovery page can be activated by powercycling the router four times
before the boot process is complete.
Note: TFTP boot can be activated only from u-boot serial console.
Device recovery address: 192.168.0.1
Signed-off-by: Amish Vishwakarma <vishwakarma.amish@gmail.com>
[fix indent]
Signed-off-by: David Bauer <mail@david-bauer.net>
