openwrt

ExternalVendorCode/openwrt

Fork 0

mirror of https://github.com/openwrt/openwrt.git synced 2024-12-23 15:32:33 +00:00

Commit Graph

Author	SHA1	Message	Date
Arınç ÜNAL	f1c9afd801	ramips: mt7621-dts: mux phy0/4 to gmac1 Mux the MT7530 switch's phy0/4 to the SoC's gmac1 on devices where RGMII2 pins are available. This achieves 2 Gbps total bandwidth to the CPU using the second RGMII. The ports called "wan" are muxed where possible. On a minority of devices, this is not possible. Those cases: mt7621_ampedwireless_ally-r1900k.dts: lan3 mt7621_ubnt_edgerouter-x.dts: eth0 mt7621_gnubee_gb-pc1.dts: ethblue mt7621_linksys_re6500.dts: lan1 mt7621_netgear_wac104.dts: lan4 mt7621_tplink_eap235-wall-v1.dts: lan0 mt7621_tplink_eap615-wall-v1.dts: lan0 mt7621_ubnt_usw-flex.dts: lan1 The "wan" port is just what the vendor designated on the board/plastic chasis of the device. On a technical level, there is no difference between a lan and wan port on MT7621AT, MT7621DAT and MT7621ST SoCs. Prefer connecting to WAN via the port described above for these devices to benefit the feature brought with this patch. mt7621_d-team_newifi-d2.dts cannot benefit this feature, although it looks like it should, because the rgmii2 pins are wired to unused components. Tested on a range of devices documented on the GitHub PR. Link: https://github.com/openwrt/openwrt/pull/10238 Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>	2022-08-20 22:56:12 +02:00
INAGAKI Hiroshi	337e942290	ramips: add support for ELECOM WRC-2533GS2 ELECOM WRC-2533GS2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB (NT5CC64M16GP-DI) - Flash : SPI-NOR 16 MiB (MX25L12835FM2I-10G) - WLAN : 2.4/5GHz 4T4R (2x MediaTek MT7615) - Ethernet : 10/100/1000 Mbps x5 - Switch : MediaTek MT7530 (SoC) - LEDs/Keys : 4x/6x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J4: 3.3V, GND, TX, RX from ethernet port side - 57600n8 - Power : 12 VDC, 1.5 A Flash instruction using factory image: 1. Boot WRC-2533GS2 normally with "Router" mode 2. Access to "http://192.168.2.1/" and open firmware update page ("ファームウェア更新") 3. Select the OpenWrt factory image and click apply ("適用") button 4. Wait ~120 seconds to complete flashing MAC Addresses: LAN : 04:AB:18:xx:xx:FB (Factory, 0xFFF4 (hex)) WAN : 04:AB:18:xx:xx:FC (Factory, 0xFFFA (hex)) 2.4 GHz : 04:AB:18:xx:xx:FD (Factory, 0x4 (hex)) 5 GHz : 04:AB:18:xx:xx:FE (Factory, 0x8004 (hex)) Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>	2022-02-11 22:30:04 +09:00

Author

SHA1

Message

Date

Arınç ÜNAL

f1c9afd801

ramips: mt7621-dts: mux phy0/4 to gmac1

Mux the MT7530 switch's phy0/4 to the SoC's gmac1 on devices where RGMII2
pins are available. This achieves 2 Gbps total bandwidth to the CPU using
the second RGMII.

The ports called "wan" are muxed where possible. On a minority of devices,
this is not possible. Those cases:

mt7621_ampedwireless_ally-r1900k.dts: lan3
mt7621_ubnt_edgerouter-x.dts: eth0
mt7621_gnubee_gb-pc1.dts: ethblue
mt7621_linksys_re6500.dts: lan1
mt7621_netgear_wac104.dts: lan4
mt7621_tplink_eap235-wall-v1.dts: lan0
mt7621_tplink_eap615-wall-v1.dts: lan0
mt7621_ubnt_usw-flex.dts: lan1

The "wan" port is just what the vendor designated on the board/plastic
chasis of the device. On a technical level, there is no difference between
a lan and wan port on MT7621AT, MT7621DAT and MT7621ST SoCs. Prefer
connecting to WAN via the port described above for these devices to benefit
the feature brought with this patch.

mt7621_d-team_newifi-d2.dts cannot benefit this feature, although it looks
like it should, because the rgmii2 pins are wired to unused components.

Tested on a range of devices documented on the GitHub PR.

Link: https://github.com/openwrt/openwrt/pull/10238
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>

2022-08-20 22:56:12 +02:00

INAGAKI Hiroshi

337e942290

ramips: add support for ELECOM WRC-2533GS2

ELECOM WRC-2533GS2 is a 2.4/5 GHz band 11ac (Wi-Fi 5) router, based on
MT7621A.

Specification:

- SoC		: MediaTek MT7621A
- RAM		: DDR3 128 MiB (NT5CC64M16GP-DI)
- Flash		: SPI-NOR 16 MiB (MX25L12835FM2I-10G)
- WLAN		: 2.4/5GHz 4T4R (2x MediaTek MT7615)
- Ethernet	: 10/100/1000 Mbps x5
  - Switch	: MediaTek MT7530 (SoC)
- LEDs/Keys	: 4x/6x (2x buttons, 1x slide-switch)
- UART		: through-hole on PCB
  - J4: 3.3V, GND, TX, RX from ethernet port side
  - 57600n8
- Power		: 12 VDC, 1.5 A

Flash instruction using factory image:

1. Boot WRC-2533GS2 normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
   ("ファームウェア更新")
3. Select the OpenWrt factory image and click apply ("適用") button
4. Wait ~120 seconds to complete flashing

MAC Addresses:

LAN	: 04:AB:18:xx:xx:FB (Factory, 0xFFF4 (hex))
WAN	: 04:AB:18:xx:xx:FC (Factory, 0xFFFA (hex))
2.4 GHz	: 04:AB:18:xx:xx:FD (Factory, 0x4    (hex))
5 GHz	: 04:AB:18:xx:xx:FE (Factory, 0x8004 (hex))

Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>

2022-02-11 22:30:04 +09:00

2 Commits