fit size should be rounded up instead of rounding down first and adding
a block. Otherwise the calculated size is one block more than needed
when fit size is exactly multiples of one block size.
Fixes: 9a863f803e ("kernel: mtdsplit: add support for FIT image")
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Qingfang Deng <qingfang.deng@siflower.com.cn>
Since 6.6 is now default, drop 6.1 support.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/15811
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Let's switch the lantiq target to use kernel 6.6 by default.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/15811
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This backports the fix for the broken "nosmp" and "maxcpus=0" cmdline
params.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/15811
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Since 6.1 is now default, drop 5.15 support.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Link: https://github.com/openwrt/openwrt/pull/15811
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add patch implementing operations to get and set flow-control link
parameters of mtk_eth_soc via ethtool.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The patches were generated from the RPi repo with the following command:
git format-patch v6.6.36..rpi-6.6.y
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
WiFi calibration data is already obtained via in-kernel NVMEM framework.
There is no need to also do so in userspace.
Fixes: dd58ad968a ("mediatek/filogic: add OpenWrt One support")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The new numberspace base starts from 512 instead of 0. The number
base seems come from the kernel symbol CONFIG_GPIOLIB_FASTPATH_LIMIT.
Suppress warning:
gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
The numberspace base has been changed since 6.6 kernel:
chip_num chip0 chip1 chip2 (32 gpios per bank)
old base 480 448 416
new base 512 544 576
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
This commit adds support for TP-LINK RE6000XD.
The device is quite similar to the Mercusys MR90X V1,
except only 3 LAN ports and more LEDs.
So thanks to csharper2005 for doing all the groundwork.
Device specification
--------------------
SoC Type: MediaTek MT7986BLA, Cortex-A53, 64-bit
RAM: MediaTek MT7986BLA (512MB)
Flash: SPI NAND GigaDevice (128 MB)
Ethernet: MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8)
Ethernet: 1x2.5Gbe (LAN3 2.5Gbps), 2xGbE (LAN 1Gbps, LAN1,
LAN2)
WLAN 2g: MediaTek MT7975N, b/g/n/ax, MIMO 4x4
WLAN 5g: MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4
LEDs: 8 LEDs, 1 status blue, 2x WIFI blue, 2x signal
blue/red, 3 LAN blue gpio-controlled
Button: 2 (Reset, WPS)
USB ports: No
Power: 12 VDC, 2 A
Connector: Barrel
Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, ubi0
partition contain "seconduboot" (also U-Boot 2022.01-rc4)
Serial console (UART), unpopulated
---------------------
V
+-------+-------+-------+-------+
| +3.3V | GND | TX | RX |
+---+---+-------+-------+-------+
|
+--- Don't connect
Disassemble: rm the 2 screws at the bottom and the one at the backside.
un-clip the case starting at the edge above the LEDs.
Installation (UART)
-------------------
1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2
2. Attach UART, switch on the router and interrupt the boot process by
pressing 'Ctrl-C'
3. Load and run OpenWrt initramfs image:
tftpboot openwrt-mediatek-filogic-tplink_re6000xd-initramfs-kernel.bin bootm
4. Run 'sysupgrade -n' with the sysupgrade OpenWrt image
Notice: while I was successfull at activating ssh (as described
here:
https://www.lisenet.com/2023/gaining-ssh-access-to-tp-link-re200-wi-fi-range-extender/)
Unfortunately I haven't found the correct root password.
Looks like they are using a static password
(md5crypt, salt + 21 characters) that is not the web
interface admin password.
The TP-LINK RE900XD looks like the very same device,
according to the pictures and the firmware.
But I haven't checked if the OpenWrt firmware works as well
on that device.
The second ubi partition (ubi1) is empty and there is no known
dual-partition mechanism, neither in u-boot nor in the stock firmware.
Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
Drop configs, files and patches for Linux 6.1.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15635
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switch to Linux kernel version 6.6.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15635
Signed-off-by: Robert Marko <robimarko@gmail.com>
Remove patches related to some ancient cache aliasing bugs that were fixed in earlier versions and are no longer relevant to us.
Co-authored-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/15635
Signed-off-by: Robert Marko <robimarko@gmail.com>
Silence ath79 GPIO driver warning by setting GPIO numberspace base
dynamically. This patch also reorganize and fix the GPIO numbers on
6.6 kernel. The new gpio chip base number algorithm:
gpiochip ath79-SOC ath9k-0 ath9k-1
base 512 512+ngpios 512+ngpios+10
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/15784
Signed-off-by: Robert Marko <robimarko@gmail.com>
Each ath9k device only has 10 gpios. ath9k-0 gpio number range is
502-511, and ath9k-1 gpio number range is 492-501. So "5GHz External
Antenna A" gpio line number should be 492 instead of 489.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/15784
Signed-off-by: Robert Marko <robimarko@gmail.com>
use u-boot-rockchip.bin to copy SPL/TPL/U-Boot to the image.
since binman was used in mainline u-boot for rockchip, we can use
u-boot-rockchip.bin instead of idbloader.img and u-boot.itb.
Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15815
Signed-off-by: Robert Marko <robimarko@gmail.com>
BDFs come from latest firmware, version 1.1.19.209880 (2022-06-20):
- /lib/firmware/IPQ4019/v1/FCC/boardData_1_0_IPQ4019_DK04_2G.bin
- /lib/firmware/IPQ4019/v1/FCC/boardData_1_0_IPQ4019_DK04_5G.bin
- /lib/firmware/QCA9888/v1/FCC/boardData_2_0_QCA9888_5G_Y9690_SBS_HB.bin
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15844
Signed-off-by: Robert Marko <robimarko@gmail.com>
As reported in https://github.com/openwrt/openwrt/issues/15834 using the PWR
LED for indicating diag status is confusing since this is usually used for
power supply failures on RPi devices.
This commit uses ACT LED for diag status and restores it to mmc activity.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
These removed compatible strings do not exist in the source code
nor the dt-binding documents. They are useless.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Some devices with MediaTek SoCs don't use the first but only the second
MAC in the chip. Especially with MT7981 which got a built-in 1GE PHY
connected to the second MAC this is quite common.
Make sure to reset and enable PSE also in those cases by skipping gaps
using 'continue' instead of aborting the loop using 'break'.
Fixes: 75081235b8 ("generic: 6.6: (re-)add support multiple PPE to mtk_eth_soc")
Reported-by: Daniel Suchy <danny@danysek.cz>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Switch to netif_napi_add_weight and add back weight value from <= v5.15.
Fixes: 8f6033e287 ("bmips: enet: add compatibility with kernel 6.1")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The bootloader provides the partition table using the boot arguments
and uses the name spi-nor and spi-nand for the different controllers.
The old code was not setting the name any more because mtd->name was
already set before. Move the setting of the name to the spi-mem code
now.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is an automatically generated commit which aids following Kernel patch
history, as git will see the move and copy as a rename thus defeating the
purpose.
For the original discussion see:
https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These targets are interesting for automated testing. The currently
available targets are from 2017 and either we should enable them again
or delete the remaining files on the download servers.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/15740
Link: https://github.com/openwrt/openwrt/pull/15740
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Currently, only the WAN MAC is being populated on Habanero DVK, and that is
happening via the ethernet1 alias so U-Boot does it, previously ethernet0
was implicitly added in the SoC DTSI so it would populate the LAN MAC-s but
it was dropped(rightly so) so now LAN MAC-s and the GMAC one are random.
So, lets simply switch to using NVMEM to assign the proper MAC adresses.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Notify via dev_info when a random MAC address is set.
of_get_ethdev_address can return -EPROBE_DEFER for NVMEM devices,
return this up, so that ipqess can defer as well.
Also move this MAC assignment from _init into _probe, so that this defer
can happen earlier.
Before change, with MAC address allocated from a built-in NVMEM layout
driver (mikrotik,routerboot-nvmem) with extra of_get_ethdev_address
result and random MAC printfs:
[ 1.197571] ipqess-edma c080000.ethernet: ipqess_init of_get_ethdev_address ret:-517, of_node: /soc/ethernet@c080000
[ 1.197690] ipqess-edma c080000.ethernet: generated random MAC address 22:e7:36:e0:e4:a3
[ 1.614444] ipqess-edma c080000.ethernet eth0: entered promiscuous mode
[ 5.055929] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode
after change:
[ 1.173776] ipqess-edma c080000.ethernet: of_get_ethdev_address: -517
[ 1.614607] ipqess-edma c080000.ethernet eth0: entered promiscuous mode
[ 5.246105] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode
[ 5.260754] ipqess-edma c080000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
with extra __func__ printf to show _probe and _init:
[ 1.173685] ipqess-edma c080000.ethernet: ipqess_axi_probe
[ 1.173784] ipqess-edma c080000.ethernet: of_get_ethdev_address: -517
[ 1.280347] ipqess-edma c080000.ethernet: ipqess_axi_probe
[ 1.304844] ipqess-edma c080000.ethernet: ipqess_init
[ 1.614664] ipqess-edma c080000.ethernet eth0: entered promiscuous mode
Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
Link: https://github.com/openwrt/openwrt/pull/15831
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that the issue with WED has been sorted out, re-add support for
multiple PPE to the mtk_eth_soc driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
"linux,ubi" compatible MTD device can be automatically attached early
since commit fc153aa8d9. Therefore, there is no need to attach MTD
devices named "ubi" or "data" again.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Used by ethernet interfaces on AP3935i.
Signed-off-by: Bryan Berg <bdb@north-eastham.org>
Link: https://github.com/openwrt/openwrt/pull/13629
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Fix issue with LAN1 interface on ap3935 devices, where the LAN
1interface won't come up after boot unless the bootloader has
initialized the network stack. Use of `fixed-link` in the prior code
kept the driver from clobbering PHY settings, but now that the driver
supports rgmii-id phy-mode, we can just use that.
Signed-off-by: Bryan Berg <bdb@north-eastham.org>
Link: https://github.com/openwrt/openwrt/pull/13629
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Updates ap3935 target to use the mdio controller built-in to gmac0,
rather than having the SoC bit-bang mdio from gpio pins
Signed-off-by: Bryan Berg <bdb@north-eastham.org>
Link: https://github.com/openwrt/openwrt/pull/13629
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Specifications:
* SoC: BCM63168
* RAM: NT5CC64M16GP-DI, DDR3 128MiB
* NAND: W29N01HVSINA, 128MiB
* Ethernet: 4x1000M LAN, 1x 1000M WAN
* Serial interface: on board but not populated, 3.3V, 115200, 8N1
Notes:
* Use DSA for VLAN and switches
* Ethernet ports and USB works
* gpio-leds are not working
* WLAN, xDSL, and FXS are not going to work
Signed-off-by: Hang Zhou <929513338@qq.com>
[refactor, reorder, drop unneeded or not working stuff]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
