Commit Graph

50490 Commits

Author SHA1 Message Date
Lech Perczak
59d065c9f8 ramips: add support for ZTE MF283+
ZTE MF283+ is a dual-antenna LTE category 4 router, based on Ralink
RT3352 SoC, and built-in ZTE P685M PCIe MiniCard LTE modem.

Hardware highlighs:
- CPU: MIPS24KEc at 400MHz,
- RAM: 64MB DDR2,
- Flash: 16MB SPI,
- Ethernet: 4 10/100M port switch with VLAN support,
- Wireless: Dual-stream 802.11n (RT2860), with two internal antennas,
- WWAN: Built-in ZTE P685M modem, with two internal antennas and two
  switching SMA connectors for external antennas,
- FXS: Single ATA, with two connectors marked PHONE1 and PHONE2,
  internally wired in parallel by 0-Ohm resistors, handled entirely by
  internal WWAN modem.
- USB: internal miniPCIe slot for modem,
  unpopulated USB A connector on PCB.
- SIM slot for the WWAN modem.
- UART connector for the console (unpopulated) at 3.3V,
  pinout: 1: VCC, 2: TXD, 3: RXD, 4: GND,
  settings: 57600-8-N-1.
- LEDs: Power (fixed), WLAN, WWAN (RGB),
  phone (bicolor, controlled by modem), Signal,
  4 link/act LEDs for LAN1-4.
- Buttons: WPS, reset.

Installation:
As the modem is, for most of the time, provided by carriers, there is no
possibility to flash through web interface, only built-in FOTA update
and TFTP recovery are supported.

There are two installation methods:
(1) Using serial console and initramfs-kernel - recommended, as it
allows you to back up original firmware, or
(2) Using TFTP recovery - does not require disassembly.

(1) Using serial console:
To install OpenWrt, one needs to disassemble the
router and flash it via TFTP by using serial console:
- Locate unpopulated 4-pin header on the top of the board, near buttons.
- Connect UART adapter to the connector. Use 3.3V voltage level only,
  omit VCC connection. Pin 1 (VCC) is marked by square pad.
- Put your initramfs-kernel image in TFTP server directory.
- Power-up the device.
- Press "1" to load initramfs image to RAM.
- Enter IP address chosen for the device (defaults to 192.168.0.1).
- Enter TFTP server IP address (defaults to 192.168.0.22).
- Enter image filename as put inside TFTP server - something short,
  like firmware.bin is recommended.
- Hit enter to load the image. U-boot will store above values in
  persistent environment for next installation.
- If you ever might want to return to vendor firmware,
  BACK UP CONTENTS OF YOUR FLASH NOW.
  For this router, commonly used by mobile networks,
  plain vendor images are not officially available.
  To do so, copy contents of each /dev/mtd[0-3], "firmware" - mtd3 being the
  most important, and copy them over network to your PC. But in case
  anything goes wrong, PLEASE do back up ALL OF THEM.
- From under OpenWrt just booted, load the sysupgrade image to tmpfs,
  and execute sysupgrade.

(2) Using TFTP recovery
- Set your host IP to 192.168.0.22 - for example using:
sudo ip addr add 192.168.0.22/24 dev <interface>
- Set up a TFTP server on your machine
- Put the sysupgrade image in TFTP server root named as 'root_uImage'
  (no quotes), for example using tftpd:
  cp openwrt-ramips-rt305x-zte_mf283plus-squashfs-sysupgrade.bin /srv/tftp/root_uImage
- Power on the router holding BOTH Reset and WPS buttons held for around
  5 seconds, until after WWAN and Signal LEDs blink.
- Wait for OpenWrt to start booting up, this should take around a
  minute.

Return to original firmware:
Here, again there are two possibilities are possible, just like for
installation:
(1) Using initramfs-kernel image and serial console
(2) Using TFTP recovery

(1) Using initramfs-kernel image and serial console
- Boot OpenWrt initramfs-kernel image via TFTP the same as for
  installation.
- Copy over the backed up "firmware.bin" image of "mtd3" to /tmp/
- Use "mtd write /tmp/firmware.bin /dev/mtd3", where firmware.bin is
  your backup taken before OpenWrt installation, and /dev/mtd3 is the
  "firmware" partition.

(2) Using TFTP recovery
- Follow the same steps as for installation, but replacing 'root_uImage'
  with firmware backup you took during installation, or by vendor
  firmware obtained elsewhere.

A few quirks of the device, noted from my instance:
- Wired and wireless MAC addresses written in flash are the same,
  despite being in separate locations.
- Power LED is hardwired to 3.3V, so there is no status LED per se, and
  WLAN LED is controlled by WLAN driver, so I had to hijack 3G/4G LED
  for status - original firmware also does this in bootup.
- FXS subsystem and its LED is controlled by the
  modem, so it work independently of OpenWrt.
  Tested to work even before OpenWrt booted.
  I managed to open up modem's shell via ADB,
  and found from its kernel logs, that FXS and its LED is indeed controlled
  by modem.
- While finding LEDs, I had no GPL source drop from ZTE, so I had to probe for
  each and every one of them manually, so this might not be complete -
  it looks like bicolor LED is used for FXS, possibly to support
  dual-ported variant in other device sharing the PCB.
- Flash performance is very low, despite enabling 50MHz clock and fast
  read command, due to using 4k sectors throughout the target. I decided
  to keep it at the moment, to avoid breaking existing devices - I
  identified one potentially affected, should this be limited to under
  4MB of Flash. The difference between sysupgrade durations is whopping
  3min vs 8min, so this is worth pursuing.

In vendor firmware, WWAN LED behaviour is as follows, citing the manual:
- red - no registration,
- green - 3G,
- blue - 4G.
Blinking indicates activity, so netdev trigger mapped from wwan0 to blue:wwan
looks reasonable at the moment, for full replacement, a script similar to
"rssileds" would need to be developed.

Behaviour of "Signal LED" in vendor firmware is as follows:
- Off - no signal,
- Blinking - poor coverage
- Solid - good coverage.

A few more details on the built-in LTE modem:
Modem is not fully supported upstream in Linux - only two CDC ports
(DIAG and one for QMI) probe. I sent patches upstream to add required device
IDs for full support.
The mapping of USB functions is as follows:
- CDC (QCDM) - dedicated to comunicating with proprietary Qualcomm tools.
- CDC (PCUI) - not supported by upstream 'option' driver yet. Patch
  submitted upstream.
- CDC (Modem) - Exactly the same as above
- QMI - A patch is sent upstream to add device ID, with that in place,
  uqmi did connect successfully, once I selected correct PDP context
  type for my SIM (IPv4-only, not default IPv4v6).
- ADB - self-explanatory, one can access the ADB shell with a device ID
  added to 51-android.rules like so:

SUBSYSTEM!="usb", GOTO="android_usb_rules_end"
LABEL="android_usb_rules_begin"
SUBSYSTEM=="usb", ATTR{idVendor}=="19d2", ATTR{idProduct}=="1275", ENV{adb_user}="yes"
ENV{adb_user}=="yes", MODE="0660", GROUP="plugdev", TAG+="uaccess"
LABEL="android_usb_rules_end"

While not really needed in OpenWrt, it might come useful if one decides to
move the modem to their PC to hack it further, insides seem to be pretty
interesting. ADB also works well from within OpenWrt without that. O
course it isn't needed for normal operation, so I left it out of
DEVICE_PACKAGES.

Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
[remove kmod-usb-ledtrig-usbport, take merged upstream patches]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-26 13:57:54 +01:00
Jeff Collins
6e0c780eb3 mvebu: add LED support for GL.iNet GL-MV1000
This patch enables LED support for the GL.iNet GL-MV1000

Signed-off-by: Jeff Collins <jeffcollins9292@gmail.com>
[add SPDX identifier on new file, add aliases, minor cosmetic issues]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-26 13:57:50 +01:00
Tom Stöveken
a6f7268dc7 ath79: fix USB power on TP-Link TL-WR810N v1
Before: Kernel reported "usb_vbus: disabling" and the USB was not
        providing power
After:  USB power is switched on, peripheral is powered from the
        device

Signed-off-by: Tom Stöveken <tom@naaa.de>
[squash and tidy up]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-26 13:57:02 +01:00
Rafał Miłecki
8078d89a53 bcm53xx: backport more upstream dts stuff from kernel 5.11
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-25 21:17:38 +01:00
Vivek Unune
39ed2265dd bcm53xx: backport Linksys Panamera (EA9500) patches
These patches have been already accepted.

302-ARM-dts-BCM5301X-Update-Northstar-pinctrl-binding.patch had to
be updated.

[rmilecki: use actual upstream accepted patches
           replace v5.10 with v5.11 to match actual upstream kernel
           recover dropped part of the pinctrl compatible patch
           update filenames
           refresh patches]

Signed-off-by: Vivek Unune <npcomplete13@gmail.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-25 21:17:38 +01:00
Rafał Miłecki
d0ee398c36 bcm53xx: group dts backports by upstream kernel version
It's a simple renaming thing.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2021-02-25 21:17:38 +01:00
Álvaro Fernández Rojas
c919f7408d bmips: dts: fix syscon-reboot nodes
Using regmap with phandles is deprecated.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-25 20:40:02 +01:00
Álvaro Fernández Rojas
5c223fb43f bmips: add BCM63268 timer clock and reset support
We need this to fix USB support on BCM63268.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-25 20:40:02 +01:00
Álvaro Fernández Rojas
e2448e5e03 bmips: rewrite pin controllers
This is needed in order to upstream them.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-25 20:40:02 +01:00
Adrian Schmutzler
ef2cb8572b treewide: rename IMAGE_PREFIX/IMAGE_NAME to DEVICE_IMG_*
We so far had two variables IMG_PREFIX and IMAGE_PREFIX with
different content. Since these names are obviously quite
confusing, this patch renames the latter to DEVICE_IMG_PREFIX,
as it's a device-dependent variable, while IMG_PREFIX is only
(sub)target-dependent.

For consistency, also rename IMAGE_NAME to DEVICE_IMG_NAME, as
that's a device-dependent variable as well.

Cc: Paul Spooren <mail@aparcar.org>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-25 18:11:06 +01:00
Daniel Golle
198385b69d mediatek: switch to use seperate ramdisk for initramfs images
MediaTek targets always use U-Boot's modern uImage.FIT format which
allows bundling several blobs into a single file including hashes,
descriptions and more. In fact, we are already using that to bundle
the Flattened Device Tree blob with the kernel on this and many
other targets.
In the same fashion, we can now make use of the newly introduced
support for building seperate ramdisk to uImage.FIT with a dedicated
initrd blob checked and loaded by U-Boot instead of embedding the
cpio archive into the kernel itself.
This allows for having larger ramdisks, choosing ramdisk compression
independently of kernel compression (while only kernel is decompressed
by the bootloader) and for more easily replacing or modifying the
filesystem contained in an initramfs image.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-25 16:39:55 +00:00
Daniel Golle
45c0e0ee41 oxnas: add experimental support for Linux 5.10
PCIe still reports link-down for some reason, RAID fails to assemble
despite SATA looking good (maybe a generic problem with RAID?)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-25 16:39:55 +00:00
Daniel Golle
dc68af4a13 image: improve Kconfig for seperate ramdisk option
* show only if target supports it (ie. seperate_ramdisk feature set)
* select XZ compression by default of ramdisk is seperate

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-25 16:39:55 +00:00
Adrian Schmutzler
722f1bd549 ath79: enable UART node for GL-USB150
This was overlooked when adding support for this device.
(It has recently been discovered that this was the only device in
ath79 having &uart disabled.)

Fixes: acc6263013 ("ath79: add support for GL.iNet GL-USB150")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-25 15:12:05 +01:00
Daniel Golle
f074541f31 image: remove bogus mkimage command
That was a left-over from testing and should not have made it into the
tree. Remove it.

Fixes: 330bd380e8 ("image: allow building FIT and uImage with ramdisk")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-25 14:07:20 +00:00
John Audia
4b92663f7a kernel: bump 5.4 to 5.4.100
Ran update_kernel.sh in a fresh clone without any existing toolchains.

Build system: x86_64
Build-tested: ipq806x/R7800
Run-tested: ipq806x/R7800

No dmesg regressions, everything functional

Signed-off-by: John Audia <graysky@archlinux.us>
[refresh again]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-25 13:08:09 +01:00
David Bauer
512229ce49 build: avoid generating JSON info on missing image
Previously, build would fail for targets containing devices with not
initramfs image (such as mpc85xx-p1010). Only generate the JSON image
info for the initramfs image when we have one to avoid breaking the
builds.

Fixes commit d3140d0529 ("build/json: generate json file for initramfs")

Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-24 22:28:45 +01:00
David Bauer
a7ff66e2d2 rtl8812au-ct: fix PKG_MIRROR_HASH
Signed-off-by: David Bauer <mail@david-bauer.net>
2021-02-24 22:28:27 +01:00
Oskari Lemmela
f0818706eb mediatek: mt7622-bananapi-bpi-r64-rootdisk rebase to upstream dts
simplify maintaining mt7622-bananapi-bpi-r64-rootdisk.dts by
storing only differences between upstream dts

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2021-02-24 19:31:19 +00:00
Oskari Lemmela
7befce2bb1 mediatek: mt7622: fix bpi-r64 emmc f2fs overlay
f2fs tools are needed for generating f2fs overlay.
vfat modules are used for recovery mounting.

Fixes: f72a2b004c ("mediatek: add bpi-r64 emmc support")
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2021-02-24 19:31:19 +00:00
Oskari Lemmela
ec2fca7c65 mediatek: mt7622: enable support for f2fs overlay
f2fs filesystem and loop device support are needed for f2fs
overlay over squashfs.

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2021-02-24 19:31:19 +00:00
Oskari Lemmela
567a5f7739 mediatek: mt7622: add missing CONFIG_MMC_BLK
CONFIG_MMC_BLK enables block devices for SD/eMMC

Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
2021-02-24 19:31:19 +00:00
Daniel Golle
f38c54c635
arm-trusted-firmware-mediatek: correct location of PKG_LICENSE
As PKG_LICENSE is originally set by include/trusted-firmware-a.mk it
can only be appended after that. Hence move that line below the
include to actually make sense.
(cosmetical change, already slipped into openwrt-21.02 branch)

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-24 19:01:14 +00:00
Kabuli Chana
dc8cc44612 kernel: bump version 5.10 to 5.10.18
update kernel version, refresh current patchset

Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
[rebase/refresh]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 18:45:59 +01:00
Álvaro Fernández Rojas
a0eff5ddff bmips: add SPI accepted PM patches
These patches have been accepted upstream.

Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
2021-02-24 18:20:04 +01:00
Adrian Schmutzler
702147b797 imx-bootlets: refresh patches
Tidy this up a little.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 16:15:02 +01:00
Adrian Schmutzler
9b37db5caa ath79: create common DTSI for Senao qca955x APs
This creates a shared DTSI for qca955x Senao/Engenius APs with
concatenated firmware partition/okli loader:

 - EAP1200H
 - EnstationAC v1

To make this usable for future boards with 32 MB flash as well,
split the partitions node already.

Suggested-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 14:08:30 +01:00
Michael Pratt
70bf4a979c ath79: rename 'engenius' Makefile definitions to 'senao'
These recipes and definitions can apply
to devices from other vendors
with PCB boards or SDK produced by Senao
not only the brand Engenius

possible examples:
Extreme Networks, WatchGuard, OpenMesh,
Fortinet, ALLNET, OCEDO, Plasma Cloud, devolo, etc.

so rename all of these items
and move DEVICE_VENDOR from common to generic/tiny.mk

Signed-off-by: Michael Pratt <mcpratt@pm.me>
2021-02-24 14:08:30 +01:00
Adrian Schmutzler
221eefaf6b zlib: properly split patches
This package had two patches (with two headers etc.) in one file,
which would have quilt merging them during a refresh.

Separate these patches into two files, as the original intent seems
to be having them separate.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 14:08:29 +01:00
Daniel Golle
287bd78e6f
base-files: remove unneeded '$' signs in nand.sh
When using Shell arithmetric evaluation via $((..)) the variables in
the expression do not need to be prefixed by the '$' sign.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-24 11:42:02 +00:00
Adrian Schmutzler
ce8b535ed3 ath79: create common DTSI for Senao ar934x APs
This creates a shared DTSI for ar934x Senao/Engenius APs:

 - EAP300 v2
 - ENS202EXT v1
 - EAP600
 - ECB600

Since ar9341/ar9344 have different configuration, this new file
mostly contains the partitioning.

Suggested-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 02:53:53 +01:00
Adrian Schmutzler
4204d70d7a ath79: create common DTSI for Senao ar724x APs
This creates a shared DTSI for ar724x Senao/Engenius APs:

 - ENH202 v1
 - EAP350 v1
 - ECB350 v1

Since ar7240/ar7242 have different configuration, this new file
mostly contains the partitioning.

Suggested-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 02:53:53 +01:00
Adrian Schmutzler
3a4b751110 ath79: enable UART in SoC DTSI files
The uart node is enabled on all devices except one (GL-USB150 *).
Thus, let's not have a few hundred nodes to enable it, but do not
disable it in the first place.

Where the majority of devices is using it, also move the serial0
alias to the DTSI.

*) Since GL-USB150 even defines serial0 alias, the missing uart
   is probably just a mistake. Anyway, disable it for now so this
   patch stays cosmetic.

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 02:53:53 +01:00
Sungbo Eo
1322150b0c kirkwood: set testing kernel version to 5.10
Tested on Pogoplug V4.

Linksys EA3500 will not build with buildbot settings and should be
disabled when the target is switched, unless the image size is
reduced again.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[add EA3500 comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 02:53:53 +01:00
Sungbo Eo
1bb3f593ee kirkwood: update config for kernel 5.10
Update config with make kernel_oldconfig.

CONFIG_SATA_PMP=y is added manually as done for 5.4.
This should be resolved properly in a separate issue.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[add back CONFIG_SATA_PMP, rebase/refresh]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 02:53:53 +01:00
Sungbo Eo
58ebc50724 kirkwood: refresh patches for kernel 5.10
Refresh patches to make them apply to kernel 5.10.
The removed patch has been merged upstream.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-02-24 02:53:53 +01:00
Sungbo Eo
e464d365fe kirkwood: copy files to kernel 5.10
Copy config and patches to kernel 5.10.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2021-02-24 02:53:53 +01:00
Adrian Schmutzler
8d766aa669 kernel: add further missing symbols
CONFIG_NET_DSA_MV88E6XXX_PTP was simply missing in generic config.

CONFIG_I2C_PXA_SLAVE was previously enabled via i2c-pxa package,
but got removed there without moving the symbol to generic config.

Fixes: dd13add3ce ("kernel: i2c-pxa: remove slave")

Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
2021-02-24 02:53:53 +01:00
Daniel Golle
5c10f26c28 sysupgrade-nand: allow limiting rootfs_data by setting env variable
Check if firmware environment variable 'rootfs_data_max' exists and is
set to a numerical value greater than 0. If so, limit rootfs_data
volume to that size instead of using the maximum available size.

This is useful on devices with lots of flash where users may want to
have eg. a volume for persistent logs and statistics or for external
applications/containers. Persistence on rootfs overlay is limited by
the size of memory available during the sysugprade process as that
data needs to be copied to RAM while the volume is being recreated
during sysupgrade. Hence it is unsuitable for keeping larger amounts
of data accross upgrade which makes additional volume(s) for
application data desirable.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-24 01:35:20 +00:00
Daniel Golle
330bd380e8 image: allow building FIT and uImage with ramdisk
Instead of embedding the initrd cpio archive into the kernel, allow
for having an external ramdisk added to the FIT or uImage.
This is useful to overcome kernel size limitations present in many
stock bootloaders, as the ramdisk is then loaded seperately and doesn't
add to the kernel size. Hence we can have larger ramdisks to host ie.
installers with all binaries to flash included (or a web-based
firmware selector).
In terms of performance and total size the differences are neglectible.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-24 01:35:20 +00:00
Daniel Golle
e6aac8d98f image: add support for building FIT image with filesystem
Allow for single (external-data) FIT image to hold kernel, dtb and
squashfs. In that way, the bootloader verifies the system integrity
including the rootfs, because what's the point of checking that the
hash of the kernel is correct if it won't boot in case of squashfs
being corrupted? Better allow bootloader to check everything needed
to make it at least up to failsafe mode. As a positive side effect
this change also makes the sysupgrade process on nand potentially
much easier as it is now.
In short: mkimage has a parameter '-E' which allows generating FIT
images with 'external' data rather than embedding the data into the
device-tree blob itself. In this way, the FIT structure itself remains
small and can be parsed easily (rather than having to page around
megabytes of image content). This patch makes use of that and adds
support for adding sub-images of type 'filesystem' which are used to
store the squashfs. Now U-Boot can verify the whole OS and the new
partition parsers added in the Linux kernel can detect the filesystem
sub-images, create partitions for them, and select the active rootfs
volume based on the configuration in FIT (passing configuration via
device tree could be implemented easily at a later stage).

This new FIT partition parser works for NOR flash (on top of mtdblock),
NAND flash (on top of ubiblock) as well as classic block devices
(ie. eMMC, SDcard, SATA, NVME, ...).
It could even be used to mount such FIT images via `losetup -P` on a
user PC if this patch gets included in Linux upstream one day ;)

Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2021-02-24 01:35:20 +00:00
Rosen Penev
fb83efb626 pcre: disable C++ bindings
Nothing uses them. Allows to simplify the Makefile.

Signed-off-by: Rosen Penev <rosenp@gmail.com>
2021-02-24 00:30:40 +01:00
DENG Qingfang
06af45ec05 ramips: remove obsolete mx25l25635f compatible hack
The kernel bump to 5.4 has removed the mx25l25635f hack, and the
mx25l25635f compatible is no longer required.

Signed-off-by: DENG Qingfang <dqfext@gmail.com>
2021-02-24 00:30:40 +01:00
Hauke Mehrtens
030bc39c35 ppp: Update to version 2.4.9
Upstream integrated multiple patches from Distributions and did other
changes:
* rp-pppoe.so was renamed to pppoe.so
* Converted to ANSI C

The following patches were applied upstream:
* 100-debian_ip-ip_option.patch
* 101-debian_close_dev_ppp.patch
* 103-debian_fix_link_pidfile.patch
* 106-debian_stripMSdomain.patch
* 107-debian_pppoatm_wildcard.patch
* 110-debian_defaultroute.patch
* 202-no_strip.patch

Compilation with musl libc was fixed upstream so
140-pppoe_compile_fix.patch is not needed any more

Parts of the 203-opt_flags.patch patch were applied in a different way
upstream.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2021-02-24 00:30:20 +01:00
Eneas U de Queiroz
12a80e44b9 openssl: always build with GOST engine support
The packages feed has a proposed package for a GOST engine, which needs
support from the main openssl library.  It is a default option in
OpenSSL.  All that needs to be done here is to not disable it.

Package increases by a net 1-byte, so it is not really really worth
keeping this optional.

This commit also includes a commented-out example engine configuration
in openssl.cnf, as it is done for other available engines.

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2021-02-23 21:10:56 +01:00
Stijn Segers
06356f0020 ramips: overwrite reset gpio properties in DIR-860L DTS
As suggested by Sergio, this adds GPIOs 19 and 8 explicitly into the
DIR-860L DTS, so the PCI-E ports get reset and the N radio (radio1)
on PCI-E port 1 comes up reliably.

Fixes the following error that popped up in dmesg:

    [    1.638942] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)

Suggested-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
2021-02-23 21:10:56 +01:00
Stijn Segers
b5bc53813d uboot-envtools: add support for ZyXEL GS-1900-8HP v1 and v2
This adds the necessary nuts and bolts for the uboot settings for both the ZyXEL GS1900-8HP v1 and v2.

Signed-off-by: Stijn Segers <foss@volatilesystems.org>
2021-02-23 21:10:56 +01:00
Sander Vanheule
773949c152 ramips: mt7621: enable SX150x driver
The Netgear R6800 and R6700v2 devices have a Semtech SX1503 GPIO
expander controlling the device LEDs. This expander was initially
supported on 4.14, but support was lost in the transition to 5.4.

Since this driver cannot be built as a kernel module, enable it in the
kernel config for all mt7621 devices.

Run-tested on a Netgear R6800.

Cc: Stijn Segers <foss@volatilesystems.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
2021-02-23 21:10:56 +01:00
Eneas U de Queiroz
d1dfb577f1 wolfssl: bump to v4.7.0-stable
Biggest fix for this version is CVE-2021-3336, which has already been
applied here.  There are a couple of low severity security bug fixes as
well.

Three patches are no longer needed, and were removed; the one remaining
was refreshed.

This tool shows no ABI changes:
https://abi-laboratory.pro/index.php?view=objects_report&l=wolfssl&v1=4.6.0&v2=4.7.0

Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
2021-02-23 21:10:56 +01:00
DENG Qingfang
920eaab1d8 kernel: DSA roaming fix for Marvell mv88e6xxx
Marvell mv88e6xxx switch series cannot perform MAC learning from
CPU-injected (FROM_CPU) DSA frames, which results in 2 issues.
- excessive flooding, due to the fact that DSA treats those addresses
as unknown
- the risk of stale routes, which can lead to temporary packet loss

Backport those patch series from netdev mailing list, which solve these
issues by adding and clearing static entries to the switch's FDB.

Add a hack patch to set default VID to 1 in port_fdb_{add,del}. Otherwise
the static entries will be added to the switch's private FDB if VLAN
filtering disabled, which will not work.

The switch may generate an "ATU violation" warning when a client moves
from the CPU port to a switch port because the static ATU entry added by
DSA core still points to the CPU port. DSA core will then clear the static
entry so it is not fatal. Disable the warning so it will not confuse users.

Link: https://lore.kernel.org/netdev/20210106095136.224739-1-olteanv@gmail.com/
Link: https://lore.kernel.org/netdev/20210116012515.3152-1-tobias@waldekranz.com/
Ref: https://gitlab.nic.cz/turris/turris-build/-/issues/165
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
2021-02-23 21:10:56 +01:00