Since we're now able to select CONFIG_NET_UDP_TUNNEL at will, drop the fake
dependencies.
This is a partial revert of commit d7e040f8bc
"kernel: add fake users for udptunnel and iptunnel modules".
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
UDP tunneling support isn't user-selectable, but it's required by WireGuard
which is, for the time being, an out-of-tree module. We currently work around
this issue by selecting an unrelated module which depends on UDP tunnelling
(VXLAN). This is inconvenient, as it implies this unrelated module needs to be
built-in when doing a monolithic build.
Fix this inconvenience by making UDP tunneling user-selectable in the kernel
configuration.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
While parsing the nm output, we need to account for the fact that 64-bit kernels
have 64-bit wide addresses. While at it, replace the grep | sed combo with a
single awk invocation and a stronger regex.
Fixes: 2ef0acc5fc "kernel-build: fix
STRIP_KERNEL_EXPORTS for recent kernels"
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This patch bumps cryptodev-linux to the latest stable release (1.11) and fixes
compilation against the next LTS (and likely OpenWrt) kernel 5.10.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Fixed license information.
Adjusted Makefile to new install paths.
Backported upstream patch to fix compilation with musl. Replaces local
and incomplete patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This patch was already applied upstream and not needed here.
Fixes: 06403981e1 ("ppp: update to version 2.4.7.git-2019-05-06")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This version fixes a large number of bugs, although no security
vulnerabilities are listed.
Full changelog at:
https://www.wolfssl.com/docs/wolfssl-changelog/
or, as part of the version's README.md:
https://github.com/wolfSSL/wolfssl/blob/v4.6.0-stable/README.md
Due a number of API additions, size increases from 374.7K to 408.8K for
arm_cortex_a9_vfpv3-d16. The ABI does not change from previous version.
Backported patches were removed; remaining patch was refreshed.
Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com>
This patch was backported to the 5.4 kernel tree as commit
c2d5c4df27e0 at least since release v5.4.28. Since then, it enables RX
an TX ready override twice.
Signed-off-by: David Bauer <mail@david-bauer.net>
glibc started to return errors from dlerror() for dlsym() lookup failures which
results in a lot of messages from fakeroot like
dlsym(acl_get_fd): staging_dir/host/lib/libfakeroot.so: undefined symbol: acl_get_fd
dlsym(acl_get_file): staging_dir/host/lib/libfakeroot.so: undefined symbol: acl_get_file
dlsym(acl_set_fd): staging_dir/host/lib/libfakeroot.so: undefined symbol: acl_set_fd
when building OpenWrt using a recent glibc. Use the patch from the upstream
Debian package to silence these messages.
Link: https://bugs.debian.org/830912
Fixes: FS#3393
Signed-off-by: Sven Wegener <sven.wegener@stealer.net>
Multiple prereq checks are only required within the build system but not
for the ImageBuilder. These checks are excluded by using ifndef IB.
This commit merges the three ifndef IB blocks together.
Signed-off-by: Paul Spooren <mail@aparcar.org>
By setting 'auto', the zero address or the empty string as source
address (option ipaddr, option ip6addr), vxlan will choose one
dynamically. This helps in setups where a wan ip or prefix changes.
This corresponse to setting up an vxlan tunnel with:
proto vxlan6:
# ip link add vx0 type vxlan id ID local :: ...
proto vxlan:
# ip link add vx0 type vxlan id ID local 0.0.0.0 ...
While it is possible to not specify a source ip at all, the kernel will
default to setting up a ipv4 tunnel. The kernel will take any hint from
source and peer ips to figure out, what tunnel type to use. To make sure
we setup an ipv6 tunnel for proto vxlan6, this workaround is needed.
This will not change the behaviour of currently working configurations.
However this will allow former broken configurations, namely those not
specifying both a source address and tunnel interface, to setup a
tunnel interface. Previously those configurations weren't reporting an
error and were stueck in a setup loop like in Bug FS#3426.
This change lifts the currently very strict behaviour and should fix the
following bug:
Fixes: FS#3426
Ref: https://bugs.openwrt.org/index.php?do=details&task_id=3426
Signed-off-by: Johannes Kimmel <fff@bareminimum.eu>
Upstream switched to building with CMake. Adjust accordingly.
Reapplied patch as upstream changed the file format.
Added HOST_BUILD_PARALLEL for faster compilation.
Added cmake tool dependency and removed circular dependencies as a
result.
Adjusted dependent tools to use NOCACHE as they are needed to build
ccache.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Since updating the MDIO driver, the probe will fail hard on any
PHY not present on the bus, while this was not the case prior.
Fixes commit 26b1f72381 ("ipq40xx: net: phy: ar40xx: remove PHY
handling")
Signed-off-by: David Bauer <mail@david-bauer.net>
Device specifications:
======================
* Qualcomm/Atheros AR9344 rev 2
* 560/450/225 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 5 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ builtin switch port 1
+ used as LAN interface
- eth1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
WAN/LAN LEDs appear to be wrong in ar71xx and have been swapped here.
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to the
device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[add LED swap comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Device specifications:
======================
* Qualcomm/Atheros AR9330 rev 1
* 400/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ builtin switch port 1
+ used as LAN interface
- eth1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* external antenna
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
======================
* Qualcomm/Atheros AR9330 rev 1
* 400/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ builtin switch port 1
+ used as LAN interface
- eth1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The find command to retrieve files from /etc/sysupgrade.conf and
/lib/upgrade/keep.d/* is used twice in almost the same way.
Move it into a function to consolidate, enhance readability and make
future adjustments easier.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
Invoke bundle-libraries.sh with any buildroot related directory entries
removed from $PATH to avoid picking up cross versions of utilities like
ldd which will not properly work when used against host executables.
This should fix executable bundling for glibc-target SDKs.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Invoke bundle-libraries.sh with any buildroot related directory entries
removed from $PATH to avoid picking up cross versions of utilities like
ldd which will not properly work when used against host executables.
This should fix executable bundling for glibc-target imagebuilders.
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Device specifications:
======================
* Qualcomm/Atheros AR9341 rev 1
* 535/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ 802.3af POE
+ builtin switch port 1
+ used as LAN interface
- eth1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
======================
* Qualcomm/Atheros AR9341 rev 1
* 535/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ 802.3af POE
+ builtin switch port 1
+ used as LAN interface
- eth1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
======================
* Qualcomm/Atheros AR9341 rev 1
* 535/400/200 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ 802.3af POE
+ builtin switch port 1
+ used as LAN interface
- eth1
+ 18-24V passive POE (mode B)
+ used as WAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[drop redundant status from eth1]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The upgrade script for the openmesh sysupgrade procedure used always an 1
byte block size. This made it easier to seek the correct position in the CE
image and to make sure the right amount of data was copied. But this also
meant that the reading/writing of data required an excessive amount of
syscalls and copy operations.
A 5.4MB big sysupgrade image on an OM2P-HS v3 needed roughly 120s for the
write operation (170s in total) during the sysupgrade.
But it is possible to reduce this overhead slightly:
* index access to read the file size can be done in single 8 byte chunk
(while doing the seek with byte granularity) because each size entry is
example 8 bytes long
* the fwupgrade.cfg can be read as one block (while seeking to its position
using its actual byte offset) because it should be rather small and fit
into the RAM easily
* the kernel can be read in 1KB blocks (while seking to its positions using
its actual byte offset) because the the size of the kernel is always a
multiple of the NOR flash block size (64KB and 256KB)
This results in a sysupgrade write time of roughly 90s (140s in total).
This could be reduced even further when also using larger chunks for the
rootfs. But the squashfs rootfs image is at the moment always
(256KB or 64KB) * block + 4 bytes
long. It would be expected that the time for the sysupgrade write could be
reduced to roughly 30s (80s in total) when busybox's dd would support
the iflag count_bytes.
Reported-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
======================
* Qualcomm/Atheros QCA9533 v2
* 650/600/217 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 2T2R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ 24V passive POE (mode B)
+ used as WAN interface
- eth1
+ 802.3af POE
+ builtin switch port 1
+ used as LAN interface
* 12-24V 1A DC
* internal antennas
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Device specifications:
======================
* Qualcomm/Atheros QCA9533 v2
* 650/600/217 MHz (CPU/DDR/AHB)
* 64 MB of RAM
* 16 MB of SPI NOR flash
- 2x 7 MB available; but one of the 7 MB regions is the recovery image
* 2x 10/100 Mbps Ethernet
* 1T1R 2.4 GHz Wi-Fi
* 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power)
* 1x GPIO-button (reset)
* external h/w watchdog (enabled by default)
* TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX)
* 2x fast ethernet
- eth0
+ Label: Ethernet 1
+ 24V passive POE (mode B)
- eth1
+ Label: Ethernet 2
+ 802.3af POE
+ builtin switch port 1
* 12-24V 1A DC
* external antenna
Flashing instructions:
======================
Various methods can be used to install the actual image on the flash.
Two easy ones are:
ap51-flash
----------
The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be
used to transfer the image to the u-boot when the device boots up.
initramfs from TFTP
-------------------
The serial console must be used to access the u-boot shell during bootup.
It can then be used to first boot up the initramfs image from a TFTP server
(here with the IP 192.168.1.21):
setenv serverip 192.168.1.21
setenv ipaddr 192.168.1.1
tftpboot 0c00000 <filename-of-initramfs-kernel>.bin && bootm $fileaddr
The actual sysupgrade image can then be transferred (on the LAN port) to
the device via
scp <filename-of-squashfs-sysupgrade>.bin root@192.168.1.1:/tmp/
On the device, the sysupgrade must then be started using
sysupgrade -n /tmp/<filename-of-squashfs-sysupgrade>.bin
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[wrap two very long lines, fix typo in comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
After device support for ASRock G10 was added in [1], several
people reported broken ipq806x devices, with one or several of the
following symptoms:
- Device does not boot
- Sysupgrade does not work
- Serial console is broken
The issues appears to be caused by the introduction of the symbol
CONFIG_CMDLINE_OVERRIDE=y in [1].
This patch disables the corresponding symbol again and marks the
ASRock as BROKEN, as it probably won't work properly without it.
Further references:
https://bugs.openwrt.org/index.php?do=details&task_id=354098b86296e6 (commitcomment-45455875)
[1] 98b86296e6 ("ipq806x: add support for ASRock G10")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
sysupgrade.bin has been added to IMAGES twice, resulting in
warnings like:
Makefile:86: warning: overriding recipe for target
'[...]/tmp/openwrt-ath79-generic-dlink_dap-2660-a1-squashfs-sysupgrade.bin'
Makefile:86: warning: ignoring old recipe for target
'[...]/tmp/openwrt-ath79-generic-dlink_dap-2660-a1-squashfs-sysupgrade.bin'
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The current support for MikroTik NAND-based devices relies on a
gross hack that packs the kernel into a static YAFFS stub, as the
stock bootloader only supports booting a YAFFS-encapsulated kernel.
The problem with this approach is that since the kernel partition is
blindly overwritten without any kind of wear or badblock management
(due to lack of proper support for YAFFS in OpenWRT), the NAND flash
is not worn uniformly and eventually badblocks appear, leading to
unbootable devices.
This issue has been reported here [1] and discussed in more detail
here [2].
[1] https://forum.openwrt.org/t/rb433-bad-sector-cannot-start-openwrt/71519
[2] https://github.com/openwrt/openwrt/pull/3026#issuecomment-673597461
Until a proper fix is found (or the stock bootloader supports other
filesystems), we disable building these images to prevent unknowing
users from risking their devices.
Thanks to Thibaut Varène for summarizing the details above.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
A few devices in ath79 and ramips use mtd-concat to concatenate
individual partitions into a bigger "firmware" or "ubi" partition.
However, the original partitions are still present and visible,
and one can write to them directly although this might break the
actual virtual, concatenated partition.
As we cannot do much about the former, let's at least choose more
descriptive names than just "firmwareX" in order to indicate the
concatenation to the user. He might be less tempted into overwriting
a "fwconcat1" than a "firmware1", which might be perceived as an
alternate firmware for dual boot etc.
This applies the new naming consistently for all relevant devices,
i.e. fwconcatX for virtual "firmware" members and ubiconcatX for
"ubi" members.
While at it, use DT labels and label property consistently, and
also use consistent zero-based indexing.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Otherwise the missing symbol is added to target config for every kernel
config refresh.
While at it, remove the disabled symbol from target configs.
Fixes: 4943bc5cff ("kernel: only strip proc for small flash devices")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Since generic has the option set to y and other targets now inherit that
choice, there is no behaviour change
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
The option was introduced in upstream linux commit a6484045 ("[TCP]: Do
not present confusing congestion control options by default.").
The option is set to y in generic config and to the moment does not
incur additional size increment. Make it y for all so that packages
such as kmod-tcp-bbr do not have to set it on every occasion
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
Specifications:
SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core
RAM: 256 MiB
FLASH1: 4 MiB NOR
FLASH2: 128 MiB NAND
ETH: Qualcomm QCA8075
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2
INPUT: Reset
LED: Power, Internet
UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
OTHER: On board with BLE module - by cp210x USB serial chip
On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed
Install via uboot tftp or uboot web failsafe.
By uboot tftp:
(IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi
(IPQ40xx) # run lf
By uboot web failsafe:
Push the reset button for 10 seconds util the power led flash faster,
then use broswer to access http://192.168.1.1
Afterwards upgrade can use sysupgrade image.
Signed-off-by: Dongming Han <handongming@gl-inet.com>
This commit adds support for Qualcomm IPQ8062 SoC.
IPQ8062 is a lower clock variant of IPQ8064.
CPU and NSS clocks:
- CPU: 384 MHz - 1 GHz
- NSS: 110 MHz - 550 MHz
opp and l2 clock values are taken from WG2600HP3 GPL source code [1].
Due to a lack of devices, I didn't test the following features.
- SATA
- NAND flash memory controller
- SD
- USB
- GSBI2, GSBI7
- PCIE2
- GMAC0, GMAC3
Works properly:
- GSBI4 UART
- GSBI5 SPI
- GMAC1, GMAC2
- PCIE0, PCIE1
- MDIO0
Does not work properly:
- CPU SPC
- This can cause a system hang. Same as IPQ8065.
See 2336c2dbb1
[1] https://www.aterm.jp/function/wg2600hp3/appendix/opensource.html
Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
The Makefile is rejecting all files with for a given prefix (here
"board-plasmacloud_pa2200") when it didn't match a known suffix. Instead it
stops the build with an error like:
Makefile:135: *** Unrecognized board-file suffix '.ipq4019' for 'board-plasmacloud_pa2200.ipq4019'. Stop.
The correct suffix for the QCA4019/hw1.0 is qca4019 and not ipq4019.
Fixes: 4871fd2616 ("ipq40xx: add support for Plasma Cloud PA2200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
The Makefile is rejecting all files with for a given prefix (here
"board-plasmacloud_pa1200") when it didn't match a known suffix. Instead it
stops the build with an error like:
Makefile:135: *** Unrecognized board-file suffix '.ipq4019' for 'board-plasmacloud_pa1200.ipq4019'. Stop.
The correct suffix for the QCA4019/hw1.0 is qca4019 and not ipq4019.
Fixes: ea5bb6bbfe ("ipq40xx: add support for Plasma Cloud PA1200")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
