345bba0 dhcpv4: improve error checking in handle_dhcpv4()
c0f6390 odhcpd: Check if open the ioctl socket failed
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
* change mx6qsabresd to mx6qsabres to match defconfig name
* merge wanboard profiles since there is only one defconfig for the target device
* move wanboard options from wandboard.h to defconfig
* remove legacy patches
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Most of the implementations behind cfg80211_get_station will not initialize
sinfo to zero before manipulating it. For example, the member "filled",
which indicates the filled in parts of this struct, is often only modified
by enabling certain bits in the bitfield while keeping the remaining bits
in their original state. A caller without a preinitialized sinfo.filled can
then no longer decide which parts of sinfo were filled in by
cfg80211_get_station (or actually the underlying implementations).
cfg80211_get_station must therefore take care that sinfo is initialized to
zero. Otherwise, the caller may tries to read information which was not
filled in and which must therefore also be considered uninitialized. In
batadv_v_elp_get_throughput's case, an invalid "random" expected throughput
may be stored for this neighbor and thus the B.A.T.M.A.N V algorithm may
switch to non-optimal neighbors for certain destinations.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on QCA4019 using bus, bmi-chip-id and
bmi-board-id.
The problem, however, can occur when the (default) board data file cannot
fulfill the vendor requirements and it is necessary to use a different
board data file.
This problem was solved for SMBIOS by adding a special SMBIOS type 0xF8.
Something similar has to be provided for systems without SMBIOS but with
device trees. No solution was specified by QCA and therefore a new one has
to be found for ath10k.
The device tree requires addition strings to define the variant name
wifi@a000000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
wifi@a800000 {
status = "okay";
qcom,ath10k-calibration-variant = "RT-AC58U";
};
This would create the boarddata identifiers for the board-2.bin search
* bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=RT-AC58U
* bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=RT-AC58U
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
With deterministic ECDSA the value k needed for the ECDSA signature is
not randomly generated any more, but generated from a hash over the
private key and the message to sign. If the value k used in a ECDSA
signature or the relationship between the two values k used in two
different ECDSA signatures over the same content is know to an attacker
he can derive the private key pretty easily. Using deterministic ECDSA
as defined in the RFC6979 removes this problem by deriving the value k
deterministically from the private key and the content which gets
signed.
The resulting signature is still compatible to signatures generated not
deterministic.
This increases the size of the ipk on mips 24Kc by about 2 KByte.
old:
166.240 libmbedtls_2.11.0-1_mips_24kc.ipk
new:
167.811 libmbedtls_2.11.0-1_mips_24kc.ipk
This does not change the ECDSA performance in a measurable way.
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Disable MBEDTLS_SHA256_SMALLER implementation, not enabled by default in
upstream and reduces performance by quite a bit.
Source: include/mbedtls/config.h
Enable an implementation of SHA-256 that has lower ROM footprint but also
lower performance.
The default implementation is meant to be a reasonnable compromise between
performance and size. This version optimizes more aggressively for size at
the expense of performance. Eg on Cortex-M4 it reduces the size of
mbedtls_sha256_process() from ~2KB to ~0.5KB for a performance hit of
about 30%.
The size of mbedtls increased a little bit:
ipkg for mips_24kc before:
164.382 Bytes
ipkg for mips_24kc after:
166.240 Bytes
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Update mbed TLS to 2.11.0
Disable OFB block mode and XTS block cipher mode, added in 2.11.0.
The soVersion of mbedtls changed, bump PKG_RELEASE for packages that use mbedTLS
This is to avoid having a mismatch between packages when upgrading.
The size of mbedtls increased a little bit:
ipkg for mips_24kc before:
163.846 Bytes
ipkg for mips_24kc after:
164.382 Bytes
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
OpenSSL defaults X509_CERT_FILE to /etc/ssl/cert.pem. This change is
needed for wget-ssl and possibly others to work seamlessly with fresh
ca-bundle installation
Fixesopenwrt/packages#6152
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* New microcode update packages from AMD upstream:
+ New Microcodes:
sig 0x00800f12, patch id 0x08001227, 2018-02-09
+ Updated Microcodes:
sig 0x00600f12, patch id 0x0600063e, 2018-02-07
sig 0x00600f20, patch id 0x06000852, 2018-02-06
* Adds Spectre v2 (CVE-2017-5715) microcode-based mitigation support,
plus other unspecified fixes/updates.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Fixes a potential infinite loop bug when in unlimited (ie not using
built in shaper) mode.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
- Removed hacks to use standalone argp as upstream now detects it nicely.
- As we are already installing files, use files from PKG_INSTALL_DIR and
not PKG_BUILD_DIR
- Only changes Makefile.am as PKG_FIXUP:=autoreconf is in use
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Refresh patches and backport upstream to current HEAD:
a997ca0 Fix sometimes missing DNSSEC RRs when DNSSEC validation not enabled.
51e4eee Fix address-dependent domains for IPv6.
05ff659 Fix stupid infinite loop introduced by preceding commit.
db0f488 Handle some corner cases in RA contructed interfaces with addresses changing interface.
7dcca6c Warn about the impact of cache-size on performance.
090856c Allow zone transfer in authoritative mode whenever auth-peer is specified.
cc5cc8f Sane error message when pcap file header is wrong.
c488b68 Handle standard and contructed dhcp-ranges on the same interface.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
This bumps to the latest & possibly greatest cake, sadly it's still
inedible but from an SQM point of view quite tasty :-)
Main tweaks since previous bump, improved ack_filter, some extra stats,
support for 64bit netlink parameters (higher rates/byte counters)
0520a6c Fix NAT option handling
8da93e1 Make sure we always call qdisc_watchdog_init() in cake_init()
f65daf6 Fix mismatched parenthesis
51d4ab3 Change flag handling to be safe even when mixing with non-eligible ACKs
f2ea091 ack_filter: protect DCTCP with stricter filtering of ECE marks
28b4560 ACK filter: Handle wrapping sequence numbers and DSACKs
73f62d9 Use the right PAD attribute for options
5969c14 Use 32 for tin backlog
e289f31 Move all the u64 netlink attributes together
36180a0 Check ACK seqno before parsing SACKs
91bbc01 Merge branch 'mine' into cobalt
58c55ec Rework SACK check to compare the ranges of two SACKs
9a5d593 ack_filter: Add proper handling of SACKs
eca95d4 ack_filter: short-circuit TCP flag check
d50a246 compat: backport some ktime functions
7b7ad11 compat: define tcpopt_fastopen for pre-4.1 kernels
ca54cdb Fix ktime compare
9d7dcc0 ack filter: Parse TCP options and only drop safe ones
b119882 Return EOPNOTSUPP on NAT option if conntrack is not available
842d7f0 Don't try to pad stats with tin_stats padding
bd46dc2 Use 64-bit divide helper
8e41bf0 Make sure we never drop SACKs when filtering ACKs
66e5d60 Avoid comparing ktime_t to scalar values
7fab017 Actually commit the ktime_t changes
fca6d13 Switch to ktime_t and get rid of cobalt.h
6f7e5af Can't use do_div with 64-bit divisors
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Bump iproute2/tc support of cake.
Add support for cake's change to u64 attribute passing for certain
attributes (rate & byte counts)
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
48cff25 build: drop install -o/-g root
53d7e7a extensions: ebt_string: take action if snprintf discards data
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This was causing issues recently as samba36 is not API compatible with the
libtdb in the packages repo. It shouldn't be using it anyway. Nor tevent.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The return value of the function isn't used anywhere.
Fixes missing return value, CID 1329717.
Found-by: Coverity
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
The previous callback code was fragile, dependent on some UCI callback
bugs and side-effects now fixed in master commit 73d8a6ab.
Update scripts to use callbacks where appropriate and necessary, while
using normal UCI config parsing for all else. This results in smaller,
simpler, more robust code. Use callbacks in generate.sh to only process
'interface' defaults and the varying entries for 'reclassify', 'default'
and 'classify' sections. Also switch qos-stat to use non-callback UCI
handling.
The current changes work independently of 73d8a6ab (i.e. both before and
after), and are consistent with UCI config parsing documentation.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
With current uboot default configuration the bootloader will
fail to start the OpenWrt firmware with the following error:
-----
unexpected character 'b' at the end of partition
Error initializing mtdparts!
incorrect device type in ubi
Partition ubi not found!
Error, no UBI device/partition selected!
Wrong Image Format for bootm command
Error occured, error code = 112
-----
If the uboot configuration is examined with printenv
I can see that mdtparts line (on a nsa310) is wrong:
-----
mtdparts=mtdparts=orion_nand:0x0c0000(uboot),
0x80000(uboot_env),0x7ec0000(ubi)bootargs_root=
----
The "bootargs_root=" that was appended to it should not be there.
Fix the issue by adding a \0 line terminator at the end of affected lines,
mimicking what is also done by uboot upstream.
This issue was detected and confirmed on a nsa310, nsa325 and
a pogoplug v4, but it's not hardware-specific, so apply the same fix
to other devices as well.
Note that the issue is with the uboot's integrated boot configuration,
which is not used unless the uboot configuration in flash is unavailable
(erased or corrupted), which happens only on first time installation,
or if the user deletes the uboot configuration when upgrading uboot.
People just upgrading from an older uboot without erasing their previous
uboot configuration stored in flash would not have noticed this issue.
Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
Add a menuconfig option to set the HOME_URL exposed in
/usr/lib/os-release independent from the
LEDE_DEVICE_MANUFACTURER_URL.
Fixes: FS#1123
Signed-off-by: Mathias Kresin <dev@kresin.me>
dfd9827 version: bump snapshot
88729f0 wg-quick: android: prevent outgoing handshake packets from being dropped
1bb9daf compat: more robust ktime backport
68441fb global: use fast boottime instead of normal boottime
d0bd6dc global: use ktime boottime instead of jiffies
18822b8 tools: fix misspelling of strchrnul in comment
0f8718b manpages: eliminate whitespace at the end of the line
590c410 global: fix a few typos
bb76804 simd: add missing header
7e88174 poly1305: give linker the correct constant data section size
fd8dfd3 main: test poly1305 before chacha20poly1305
c754c59 receive: don't toggle bh
Compile-tested-for: ath79 Archer C7 v2
Run-tested-on: ath79 Archer C7 v2
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
After a very enlightening but unfortunately far too short exchange with Jes
we mutually agreed to drop the patches. They are unfortunately not ready
yet.
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: John Crispin <john@phrozen.org>
This patch adds support for ZyXEL NBG6617
Hardware highlights:
SOC: IPQ4018 / QCA Dakota
CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7
DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz
NOR: 32 MiB Macronix MX25L25635F
ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN)
USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC)
WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2
WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2
INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button
LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS
Serial:
WARNING: The serial port needs a TTL/RS-232 3.3v level converter!
The Serial setting is 115200-8-N-1. The 1x4 .1" header comes
pre-soldered. Pinout:
1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX
first install / debricking / restore stock:
0. Have a PC running a tftp-server @ 192.168.1.99/24
1. connect the PC to any LAN-Ports
2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file
into the tftp-server root directory and rename it to just "ras.bin".
3. power-cycle the router and hold down the the WPS button (for 30sek)
4. Wait (for a long time - the serial console provides some progress
reports. The u-boot says it best: "Please be patient".
5. Once the power LED starts to flashes slowly and the USB + WPS LEDs
flashes fast at the same time. You have to reboot the device and
it should then come right up.
Installation via Web-UI:
0. Connect a PC to the powered-on router. It will assign your PC a
IP-address via DHCP
1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234)
2. Go to the "Expert Mode"
3. Under "Maintenance", select "Firmware-Upgrade"
4. Upload the OpenWRT factory image
5. Wait for the Device to finish.
It will reboot into OpenWRT without any additional actions needed.
To open the ZyXEL NBG6617:
0. remove the four rubber feet glued on the backside
1. remove the four philips screws and pry open the top cover
(by applying force between the plastic top housing from the
backside/lan-port side)
Access the real u-boot shell:
ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02"
When the device is starting up, the user can enter the the loader shell
by simply pressing a key within the 3 seconds once the following string
appears on the serial console:
| Hit any key to stop autoboot: 3
The user is then dropped to a locked shell.
|NBG6617> HELP
|ATEN x[,y] set BootExtension Debug Flag (y=password)
|ATSE x show the seed of password generator
|ATSH dump manufacturer related data in ROM
|ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations)
|ATGO boot up whole system
|ATUR x upgrade RAS image (filename)
|NBG6617>
In order to escape/unlock a password challenge has to be passed.
Note: the value is dynamic! you have to calculate your own!
First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env)
to get the challange value/seed.
|NBG6617> ATSE NBG6617
|012345678901
This seed/value can be converted to the password with the help of this
bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors):
- tool.sh -
ror32() {
echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
}
v="0x$1"
a="0x${v:2:6}"
b=$(( $a + 0x10F0A563))
c=$(( 0x${v:12:14} & 7 ))
p=$(( $(ror32 $b $c) ^ $a ))
printf "ATEN 1,%X\n" $p
- end of tool.sh -
|# bash ./tool.sh 012345678901
|
|ATEN 1,879C711
copy and paste the result into the shell to unlock zloader.
|NBG6617> ATEN 1,0046B0017430
If the entered code was correct the shell will change to
use the ATGU command to enter the real u-boot shell.
|NBG6617> ATGU
|NBG6617#
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Add xt_bpf modules to {kmod-ipt,iptables-mod}-filter.
Match using Linux Socket Filter. Expects a BPF program in decimal
format. This is the format generated by the nfbpf_compile utility.
Signed-off-by: Alin Nastac <alin.nastac@gmail.com>
Commit 61d57a2f88 adds ath10k LED
support, but doesn't add an option to actually enable it.
After enabling this option, a LED named ath10k-phy0 appears in sysfs,
and a trigger can be assigned to it. Since 60deb3cdef the default set
trigger is the tpt one.
Enable it by default, as most devices using ath10k chips shouldn't be
severely space-constrained. There are likely many devices that can
benefit from having it enabled, like my testing device.
Before:
text data bss dec hex filename
245311 8899 16 254226 3e112 ath10k_core.ko
After:
text data bss dec hex filename
245979 8899 16 254894 3e3ae ath10k_core.ko
Tested on a D-Link DAP-2695-A1 (ar71xx).
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Use the tpt LED trigger for each created phy led. Ths way LEDs attached
to the ath10k GPIO pins are indicating the phy status and blink on
traffic.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Includes specific support for PH8(1e2d-0053) / ELS61(1e2d-005b) modules.
Note for ELS61, the serial driver changes from serial option(ttyUSB) to usb-cdc (ttyACM).
Two additional fixes in this commit resolve issues with ttyACM devices: -
* wwan.sh - sys-fs has a subdirectory indirection (*/tty/ttyACMx) which was not handled properly
* wwan.usb - dependent scripts were not included, so this never actually called proto_set_available for example (and relied on inadvertent call for ttyUSB case)
Signed-off-by: David Thornley <david.thornley@touchstargroup.com>
