These things are regulators. Should silence dmesg messages about using
dummy regulators.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16804
Signed-off-by: Robert Marko <robimarko@gmail.com>
It should be debounce-interval, as with the others.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16802
Signed-off-by: Robert Marko <robimarko@gmail.com>
It does the same thing minus a few dmesg prints.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16788
Signed-off-by: Robert Marko <robimarko@gmail.com>
The WiFi chips are actually on PCIe1 and PCIe2, PCIe0 is empty. Fix the
assignment so that WiFi works properly again.
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/16807
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Drop kmod-i2c-ralink from ASUS RP-AC56 as it was wrongly added. Such
kmod is not supported on mt7621 as i2c is handled by the mediatek driver
and not bay the ralink downstream one.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
No need for irq_of_parse_and_map since this is in _probe.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16771
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
This converts all RT3662 and RT3883 devices to use interrupt based
gpio-keys instead of gpio-keys-polled. The poll-interval will be
removed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16764
Signed-off-by: Robert Marko <robimarko@gmail.com>
This converts all RT305x and RT5350 devices to use interrupt based
gpio-keys instead of gpio-keys-polled. The poll-interval will be
removed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16764
Signed-off-by: Robert Marko <robimarko@gmail.com>
This converts all RT2880 devices to use interrupt based gpio-keys
instead of gpio-keys-polled. The poll-interval will be removed.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16764
Signed-off-by: Robert Marko <robimarko@gmail.com>
All other MT76x8 devices have already been migrated to gpio-keys.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16764
Signed-off-by: Robert Marko <robimarko@gmail.com>
The Ralink GPIO driver supports irqchip function. Hence we need to
add "interrupt-parent" and "interrupt-controller" properties to make
sure it works properly. It is worth noting that all GPIO devices
share the same interrupt line.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16764
Signed-off-by: Robert Marko <robimarko@gmail.com>
The gpiolib has already introduced a general GPIO irqchip framework
to initialize the GPIO irqchip[1]. This patch will make use of it
to simplify the legacy Ralink GPIO driver codes. This patch also
includes some code readability improvements.
[1] 1425052097b5 ("gpio: add IRQ chip helpers in gpiolib")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16764
Signed-off-by: Robert Marko <robimarko@gmail.com>
Easier to just use devm_platform_ioremap_resource.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16701
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Mikrotik seems to prefer "hEX S" as general name for this model,
therefore include this in devicetree model name as well.
Signed-off-by: Priit Laes <plaes@plaes.org>
Link: https://github.com/openwrt/openwrt/pull/16658
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Increase usage of devm to get rid of goto and _remove.
Get rid of hw_reset_count. It's not really used for anything.
Use dev_err_probe to handle potential EPROBE_DEFER.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16588
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Gemtek WVRTM-127ACN is an indoor dual band wifi router
with internal antennas and 3 Gigabit Ethernet ports.
The Gemtek WVRTM-130ACN is an indoor dual band wifi router
with external antennas and 5 Gigabit Ethernet ports.
Hardware of WVRTM-127ACN:
- SoC: Mediatek MT7621AT (880 MHz, dual core)
- RAM: 128 MB
- Storage: 128 MB NAND SLC flash
- Ethernet: 3x 10/100/1000 Mbps LAN1,LAN2 & WAN
- Wireless: 2.4GHz: Mediatek MT7603EN (802.11b/g/n)
- Wireless: 5GHz: Mediatek MT7612EN (802.11n/ac)
- LEDs: 11x
- Buttons: 2x WPS, reset
- USB: 1x 3.0
- Power: 56 VDC, 0.54 A, PoE+ IN (WAN)
- PoE: 1x PoE+ 802.3af/at (WAN)
- Uart: GND RX TX VCC - J2 (GND near WAN)
- Board silkscreen: "WVRTM-127ACN_V02" "19K-513-8500R" "RoHS" "1717"
Hardware of WVRTM-130ACN:
- SoC: Mediatek MT7621AT (880 MHz, dual core)
- RAM: 128 MB (Kioxia TC58BVG0S3HTA00)
- Storage: 128 MB NAND SLC (Winbond W971GG6SB-25)
- Ethernet: 5x 10/100/1000 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
- Wireless: 2.4GHz and 5GHz Mediatek MT7615DN (802.11ac/b/g/n) (DBDC)
- LEDs: 10x
- Buttons: 3x Power, WPS, reset
- USB: 1x 3.0
- Power: 56 VDC, 0.54 A, PoE+ (WAN)
- PoE: 1x PoE+ 802.3af/at (WAN)
- Uart: GND RX TX VCC - J2 (GND near WAN)
- Board silkscreen: "WVRTM-130ACN_V01" "19K-515-4500R" "RoHS" "2112"
Enable access to uboot menu (needed in wvrtm-130acn):
- The access to uboot menu is blocked by `bootdelay = 0` set in ubootenv.
With stock firmware version 01.01.02.163 and previous, you can use CVE 2020-24365
command injection https://nvd.nist.gov/vuln/detail/CVE-2020-24365
python3 exploit.py -t 192.168.1.1 -c "fw_setenv bootdelay 3; fw_saveenv"
Backup the stock firmware:
- Connect via uart
- Connect via ethernet and assign your pc the address 192.168.15.x/24
- Power on the device; and start typing '4' to enter uboot menu
- Set factory mode and boot
MT7621 # setenv factory 2; saveenv
MT7621 # nand read 2800000 2000000 81000000; bootm
- Telnet and copy all mtd blocks
telnet 192.168.15.1
- Copy all mtd blocks and start webserver
for N in $(seq 0 6); do dd if=/dev/mtd$N of=/tmp/eeprom_mtd$N.bin; done
mount -o bind /tmp /www
lighttpd -f /etc/lighttpd.conf
- Backup stock rootfs_data (optional)
dd if=/dev/mtd7 of=/tmp/eeprom_mtd7.bin
dd if=/dev/mtd8 of=/tmp/eeprom_mtd8.bin
- Download to your pc from http://192.168.15.1/eeprom_mtd$N.bin
Installation:
- Connect via uart
- Connect via ethernet and assign your pc the address 10.10.10.3/24
- Start a tftp server and serve the image initramfs-kernel.bin
mkdir /tmp/ftpd;
cp initramfs-kernel.bin /tmp/ftpd/kernel.bin
dnsmasq --enable-tftp --tftp-root=/tmp/ftpd
- Power on the device; and start typing '4' to halt the bootloader
- Change the active mtd partition from mtd6 to mtd5 (needed by uboot)
MT7621 # setenv mtddevnum 5; saveenv
- Write the openwrt initramfs in ram via tftp and boot it
MT7621 # tftpboot 81000000 kernel.bin; bootm
- From the initramfs create the ubi device and install openwrt via sysupgrade
ubiformat /dev/mtd11 -y
sysupgrade -n -v /tmp/sysupgrade.bin
Recovery:
Restore the stock firmware from the backup of the mtd blocks
mtd write eeprom_mtd5.bin firmware
mtd write eeprom_mtd6.bin Kernel2
mtd write eeprom_mtd7.bin Storage1
mtd write eeprom_mtd8.bin Storage2
ubiformat /dev/mtd8 -y
reboot
Links to previous works on wvrtm-127acn:
https://github.com/digiampietro/hacking-gemtekhttps://forum.openwrt.org/t/add-support-for-gemtek-wvrtm-127acn-linkem-provider/168757
Signed-off-by: Samuele Longhi <agave@dracaena.it>
Link: https://github.com/openwrt/openwrt/pull/16685
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In #16396, crashes were reported on MT7620, which were introduced by enabling
CONFIG_LIST_HARDENED. The cause seems to be random memory corruption somewhere
in the kernel. Unfortunately the crash traces do not point to the real cause
of the crash in any way.
Since MT7620 is really ancient hardware that likely only has few users left,
I don't expect that anybody will invest a significant amount of time to track
down the real cause. Because of that, let's disable CONFIG_LIST_HARDENED on
this target only, and leave it enabled on all other platforms.
Fixes: #16396
Signed-off-by: Felix Fietkau <nbd@nbd.name>
73a9f9f857 added support. Let's use it.
Calibration data is not yet supported.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16256
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The SPI driver framework can handle it automatically in
spi.c:spi_setup():spi_set_cs():gpiod_set_value_cansleep().
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16636
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Set compatible string and specify redundant type U-boot environment.
Fixes: fea2264d9f ("ramips: mt7621: Add DNA Valokuitu Plus EX400")
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/16573
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Enable above drivers for mt7621 targets. They are needed for retrieving a MAC
address stored in a U-boot environment residing on an UBI volume.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
Link: https://github.com/openwrt/openwrt/pull/16573
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use more devm and remove _remove function.
Remove owner as the kernel sets it automatically.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16546
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently eth1 (which is the first "lan" interface) doesn't work on this device.
During boot the following can be seen in logs:
```
[ 2.252804] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 2.266060] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 19
[ 2.277889] mtk_soc_eth 1e100000.ethernet eth1: mediatek frame engine at 0xbe100000, irq 19
...
[ 2.355157] mt7530-mdio mdio-bus:1f: MT7530 adapts as multi-chip module
[ 2.390312] mt7530-mdio mdio-bus:1f: configuring for fixed/rgmii link mode
[ 2.398597] mt7530-mdio mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 2.403872] mt7530-mdio mdio-bus:1f eth1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=21)
[ 2.416988] mtk_soc_eth 1e100000.ethernet eth0: error -17 registering interface eth1
[ 2.426973] mt7530-mdio mdio-bus:1f eth2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=22)
[ 2.440996] mt7530-mdio mdio-bus:1f eth3 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=23)
[ 2.454405] mt7530-mdio mdio-bus:1f eth4 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=24)
[ 2.467198] mtk_soc_eth 1e100000.ethernet eth0: entered promiscuous mode
[ 2.474117] DSA: tree 0 setup
...
[ 6.820998] mtk_soc_eth 1e100000.ethernet dsa: renamed from eth0
[ 6.919904] mtk_soc_eth 1e100000.ethernet wan: renamed from eth1
```
So the problem seems to be the fact that built-in gmacs get default
names (eth0/eth1) and are renamed after switch ports are initialized. This means
that when switch port with name `eth1` is brought up this name is still used by
gmac1 causing switch port's init to fail.
This patch just renames the ports to avoid name collision.
Note: this will break existing configs for this device because it renames all
the ports. This should not be major problem because this device doesn't have a
proper OEM image and is only flashable with serial access, meaning there should
not be many users.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/15865
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This driver does not support more than 1 queue.
Fixes: ba24b94e0b ("ramips: use more devm in mtk_eth_soc")
Signed-off-by: Rosen Penev <rosenp@gmail.com>
These got added to the kernel after this driver was written.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16415
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Hardware Specification:
SoC: Mediatek MT7621DAT (MIPS1004Kc 880 MHz, dual core)
RAM: 128 MB
Storage: 128 MB NAND flash
Ethernet: 5x 10/100/1000 Mbps LAN1,LAN2,LAN3,LAN4 & WAN
Wireless: 2.4GHz: Mediatek MT7603EN up to 300Mbps (802.11b/g/n MIMO 2x2)
Wireless: 5GHz: Mediatek MT7615N up to 1733Mbps (802.11n/ac MU-MIMO 4x4)
LEDs: Power (white & amber), Internet (white & amber)
LEDs: 2.4G (White), 5Ghz (White)
Buttons: WPS, Reset
USB: Front V3.0 & Rear V2.0
MAC Table
Label xx:xx:xx:xx:xx:38
LAN xx:xx:xx:xx:xx:39
2.4Ghz xx:xx:xx:xx:xx:3A
5Ghz xx:xx:xx:xx:xx:3C
WAN xx:xx:xx:xx:xx:38
Flash Instructions:
D-Link normal OEM firmware update page
1. upload OpenWRT factory.bin like any D-Link upgrade image
D-Link Fail Safe GUI:
1. Push and hold reset button (on the bottom of the device) until power led starts flashing (about 10 secs or so) while plugging in the power cable.
2. Give it ~30 seconds, to boot the fail safe GUI
3. Connect your client computer to LAN1 of the device
4. Set your client IP address manually to 192.168.0.2 / 255.255.255.0
5. Call the fail safe page for the device at http://192.168.0.1/
6. Use the provided fail safe web GUI to upload the factory.bin to the device
Signed-off-by: Alan Luck <luckyhome2008@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16269
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Only one device uses the dtsi file "rt3883_belkin_f9k110x.dtsi".
So there is no need to split the device tree.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16318
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
2 GHz WiFi doesn't work on the wmac of this device.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Link: https://github.com/openwrt/openwrt/pull/16318
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
SoC: MediaTek MT7621
Flash: 16MB (Macronix MX25L12805D)
RAM: 128MB
Serial: As marked on PCB, baudrate is 57600, DO NOT CONNECT 3.3V!!!
Ethernet: 4x 10/100/1000 Mbps (3x LAN + WAN)
WIFI0: MT7615 2.4GHz 802.11b/g/n
WIFI1: MT7615 5GHz 802.11ac
Antennas: 6x external (3 per radio), non-detachable
LEDs: Programmable power-LED (blue-colored)
Buttons: Reset
INSTALLATION:
Get rootshell using insructions from https://gist.github.com/ZIKH26/18693c67ee7d2f8d2c60231b19194c37
Download and flash image
On computer:
python -m http.server
On router:
cd /tmp
wget http://:8000/factory.bin
mtd -r write factory.bin firmware
Device should reboot at this point.
Reverting to stock:
Download archive with firmware from Ruijie's site and
get .bin file from it. Then write that binary to firmware
partition. After reboot, factory-reset the router using
reset button.
Signed-off-by: Yahor Leonenka <staryjakau@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16202
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ELECOM WSC-X1800GS is a 2.4/5 GHz band 11ax (Wi-Fi 6) mesh extender,
based on MT7621A
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
- Flash : RAW-NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7915D + MT7975D)
- Ethernet : 2x 10/100/1000 Mbps
- switch : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO): 9x/2x
- UART : through-hole on PCB ("J4")
- arrangement : 3.3V, GND, TX, RX from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 10.5 W)
Flash instruction using initramfs-factory image
1. Boot WMC-X1800GST normally
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
button
4. On initramfs image, download sysupgrade image to the device and
perform sysupgrade with that image
5. Wait ~120 seconds to complete flashing
Notes:
- The "firmware" partition on the stock image is only 0xF00000 (15 MiB)
and it's too small for the current OpenWrt firmware with UBI format.
So use the unused area at the end of NAND flash for rootfs (UBI).
MAC addresses:
LAN : 04:AB:18:xx:xx:6E (Factory, 0x3fff4 (hex))
2.4 GHz: 04:AB:18:xx:xx:6F (Factory, 0x3fffa (hex))
5 GHz : 04:AB:18:xx:xx:70 (Factory, 0x4 (hex))
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16384
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
ELECOM WMC-X1800GST is a 2.4/5 GHz band 11ax (Wi-Fi 6) mesh router,
based on MT7621A
Specification:
- SoC : MediaTek MT7621A
- RAM : DDR3 512 MiB (Nanya NT5CC256M16ER-EK)
- Flash : RAW-NAND 128 MiB (Winbond W29N01HVSINF)
- WLAN : 2.4/5 GHz 2T2R (MediaTek MT7915D + MT7975D)
- Ethernet : 3x 10/100/1000 Mbps
- switch : MediaTek MT7530 (SoC)
- LEDs/Keys (GPIO): 9x/5x
- UART : through-hole on PCB ("J4")
- arrangement : 3.3V, GND, TX, RX from tri-angle marking
- settings : 115200n8
- Power : 12 VDC, 1 A (Max. 11.5 W)
Flash instruction using initramfs-factory image
1. Boot WMC-X1800GST normally with "Router" mode
2. Access to "http://192.168.2.1/" and open firmware update page
("ファームウェア更新")
3. Select the OpenWrt initramfs-factory image and click apply ("適用")
button
4. On initramfs image, download sysupgrade image to the device and
perform sysupgrade with that image
5. Wait ~120 seconds to complete flashing
Notes:
- The "firmware" partition on the stock image is only 0xF00000 (15 MiB)
and it's too small for the current OpenWrt firmware with UBI format.
So use the unused area at the end of NAND flash for rootfs (UBI).
MAC addresses:
LAN : 04:AB:18:xx:xx:BF (Factory, 0x3fff4 (hex))
WAN : 04:AB:18:xx:xx:C0 (Factory, 0x3fffa (hex))
2.4 GHz: 04:AB:18:xx:xx:C1 (Factory, 0x4 (hex))
5 GHz : 04:AB:18:xx:xx:C2
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16384
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Rename the sysupgrade.tar step to sysupgrade.bin. The sysupgrade.tar is
used in other places and we prefer a sysupgrade.bin instead.
Fixes: fea2264d9f ("ramips: mt7621: Add DNA Valokuitu Plus EX400")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The sysupgrade-tar image build is not defined for this target, do not
add a build instruction for it. The build system will use the definition
from the dna_valokuitu-plus-ex400 board and the build will fail.
This fixes the build of the ramips target.
Fixes: 665c2154ef ("ramips: add basic support for tp-link er605-v2")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds support for netis N6 WiFi 6 router.
Specification
-------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (ESMT PSU1GA30DT)
- WLAN : MT7905DAN + MT7975DN
- 2.4 GHz : b/g/n/ax, 574 Mbps, MIMO 2x2
- 5 GHz : a/n/ac/ax, 1201 Mbps, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x5 (1x WAN, 4x LAN)
- USB : 1x 3.0
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
1x WPS
- LEDs : 1x Power (green)
1x System (green)
1x WAN (green)
1x WiFi 2.4 GHz (green), controlled by phy
1x WiFi 5 GHz (green), controlled by phy
1x WPS (green)
1x USB (green)
5x ethernet leds (green), controlled by switch
- Power : 12 VDC, 1.5 A
Installation
------------
1. Update the router using stock firmware web interface and OpenWrt
factory.bin image.
Recovery and return to stock
----------------------------
1. Assign your PC a static IP 192.168.1.2 and connect to the router using
the ethernet cable;
2. Power off the router;
3. Press Reset button, power on the router and wait until ethernet led
start blinking;
4. Release the button;
5. Open http://192.168.1.1/ (N6 System Recovery Mode) in your browser;
6. Upload OpenWrt factory.bin (or stock firmware *.bin) image and proceed
with upgrade.
MAC addresses
-------------
+---------+-------------------+
| | MAC example |
+---------+-------------------+
| LAN | dc:xx:xx:49:xx:04 |
| WAN | dc:xx:xx:49:xx:05 |
| WLAN 2g | dc:xx:xx:19:xx:06 |
| WLAN 5g | dc:xx:xx:79:xx:06 |
+---------+-------------------+
The WLAN MAC prototype was found in 'Factory', 0x4
The LAN MAC was found in 'Factory', 0x7ef20
The WAN MAC was found in 'Factory', 0x7ef26
Known issue
-----------
2.4 GHz WLAN doesn't start with mt76 driver.
Probable reason:
Original Netis N6 EEPROM contains wrong MT_EE_WIFI_CONF value (0xd2).
Other routers with the same WLAN hardware (e.g., Routerich AX1800)
have MT_EE_WIFI_CONF = 0x92.
Workaround (already included in this commit):
Extract EEPROM to a file at the first time boot and change
MT_EE_WIFI_CONF (offset 0x190) value from 0xd2 to 0x92. See
/etc/hotplug.d/firmware/11-mt76-caldata for details.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This files are executable:
target/linux/ramips/dts/mt7621_openfi_5pro.dts
target/linux/ramips/dts/mt7621_winstars_ws-wn536p3.dts
Has to be fixed.
Fixes: 5560791 ("ramips: add support for OpenFi 5Pro Travel Router")
Fixes: 2da2705 ("ramips: add support for WINSTARS WS-WN536P3")
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/16322
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This fixes a well-known "LZMA ERROR 1" error on Sercomm NA502s, reported
on the OpneWrt forum [0].
[0] https://forum.openwrt.org/t/206640
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Specifications:
- Device: DNA Valokuitu Plus EX400
- SoC: MT7621A
- Flash: 256MB NAND
- RAM: 256MB
- Ethernet: Built-in, 2 x 1GbE
- Wifi: MT7603 2.4 GHz, MT7615 5 GHz (4x internal antennas)
- USB: 1x 3.0
- LED: 1x green/red, 1x green
- Buttons: Reset
MAC addresses:
- LAN: u-boot 'ethaddr' (label)
- WAN: label + 1
- 2.4 GHz: label + 6
- 5 GHz: label + 7
Serial:
There is a black block connector next to the red ethernet connector. It
is accessible also through holes in the casing.
Pinout (TTL 3.3V)
+---+---+
|Tx |Rx |
+---+---+
|Vcc|Gnd|
+---+---+
Firmware:
The vendor firmware is a fork of OpenWrt (Reboot) with a kernel version
4.4.93. The flash is arranged as below and there is a dual boot
mechanism alternating between rootfs_0 and rootfs_1.
+-------+------+------+-----------+-----------+
| | env1 | env2 | rootfs_0 | rootfs_1 |
| +------+------+-----------+-----------+
| | UBI volumes |
+-------+-------------------------------------+
|U-Boot | UBI |
+-------+-------------------------------------+
|mtd0 | mtd1 |
+-------+-------------------------------------+
| NAND |
+---------------------------------------------+
In OpenWrt rootfs_0 will be used as a boot partition that will contain the
kernel and the dtb. The squashfs rootfs and overlay are standard OpenWrt
behaviour.
+-------+------+------+-----------+--------+------------+
| | env1 | env2 | rootfs_0 | rootfs | rootfs_data|
| +------+------+-----------+--------+------------+
| | UBI volumes |
+-------+-----------------------------------------------+
|U-Boot | UBI |
+-------+-----------------------------------------------+
|mtd0 | mtd1 |
+-------+-----------------------------------------------+
| NAND |
+-------------------------------------------------------+
U-boot:
With proper serial access booting can be halted to U-boot by pressing any
key. TFTP and flash writes are available, but only the first one has been
tested.
NOTE: Recovery mode can be accessed by holding down the reset button while
powering on the device. The led 'Update' will show a solid green light
once ready. A web server will be running at 192.168.1.1:80 and it will
allow flashing a firmware package. You can cycle between rootfs_0 and
rootfs_1 by pressing the reset button once.
Root password:
With the vendor web UI create a backup of your settings and download the
archive to your computer. Within the archive in the file
/etc/shadow replace the password hash for root with that of a password you
know. Restore the configuration with the vendor web UI and you will have
changed the root password.
SSH access:
You might need to enable the SSH service for LAN interface as by default
it's enabled for WAN only.
Installing OpenWrt:
With the vendor web UI install the OpenWrt factory image. Alternatively,
ssh to the device and use sysupgrade -n from cli.
Finalize by installing the OpenWrt sysupgrade image to get a fully
functioning system.
Reverting to the vendor firmware:
Boot with OpenWrt initramfs image
- Remove volumes rootfs_0, rootfs and rootfs_data and create vendor
volumes.
ubirmvol /dev/ubi0 -n 2
ubirmvol /dev/ubi0 -n 3
ubirmvol /dev/ubi0 -n 4
ubimkvol /dev/ubi0 -N rootfs_0 -S 990
ubimkvol /dev/ubi0 -N rootfs_1 -S 990
Power off and enter to the U-boot recovery to install the vendor
firmware.
Known issues:
- MACs for wifi are stored in currently unknown place but it seems
to persist over power-off. They might be stored on the chip.
Signed-off-by: Mauri Sandberg <maukka@ext.kapsi.fi>
[rmilecki: try NVMEM for MACs]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Add missing 'model' string to DT, so /tmp/sysinfo/model gets populated.
Fixes: e497c975d3 ("ramips: mt76x8: add support for Yuncore M300")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
