Explain some of the more obscure logic, or where we deviate from
what the original awk code did. Also, give a count of the usable
addresses on the subnet.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
This is useful if you later need to perform numeric range-checking
on addresses, i.e. to see if an address falls inside a CIDR range,
etc. and what interface it corresponds to.
Signed-off-by: Philip Prindeville <philipp@redfish-solutions.com>
Without that, imx_thermal fails to initialize on deferred probe, because
it fails to register cpufreq cooling device.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
PFUZE100 series of PMICs are used on boards supported by both
subtargets. Enable this for whole i.MX target.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
ledumon:
This program creates a new userspace LED class device and monitors it.
For this it es using the kmod-leds-uled.ko kernel module.
ledhwbmon:
This program monitors LED brightness level changes having its origin
in hardware/firmware, i.e. outside of kernel control.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
In 749237967a downstream dts was replaced with upstream accepted
patch. But in upstream version last partition was called "rootfs"
instead "ubi". OpenWrt require "ubi" label for ubi rootfs.
This patch restore proper label.
Fixes: 749237967a ("kirkwood: Replace dtses with upstream accepted")
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
The kernel patches apply with only minor changes. The only other notable
change is that octeon-usb has moved from staging and had its config
macro renamed from CONFIG_OCTEON_USB to CONFIG_USB_OCTEON_HCD.
Signed-off-by: Christian Svensson <blue@cmd.nu>
Drop useless uci-defaults compat version script as it's not needed
anymore and should have been dropped on DSA conversion.
The script was needed for Linksys EA7500 and EA8500 for the kernel space
migration. We now handle compat version setting in board.d scripts.
Having this script with actually the wrong value (2.0) cause upgrade
problem and conflicts with board.d script.
Fixes: 337e36e0ef ("ipq806x: convert each device to DSA implementation")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
8f2806a37fe1 system-linux: set master early on apply settings
e3fc2b0026a5 system-linux: skip refreshing MAC on master change if custom MAC
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Pick commits adding drivers for audio engine found in MT7986 from
Linux 6.6 as well as follow-up fixes from Linux 6.7.
Signed-off-by: Maso Huang <maso.huang@mediatek.com>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fix typo calling lua53 instead of lua5.3 for Package Default definition.
This cause only missing description of the package and doesn't cause
any build regression.
Fixes: c52ca08d40 ("lua5.3: build shared library")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The Bonanza Peak series are a couple of MT7986-powered 2.5 GBit/s
Wi-Fi 6 residential gateway, access point and mesh router products.
All of them come with an eMMC to boot from, are powered via USB-C and
got a USB 3.0 type-A port. All of them got a Dialog (Renesas) DA14531
Bluetooth module connected via UART. If the device was previously
running stock firmware, the BT chip's internal flash has been loaded
with firmware and it can be attached using hciattach when using
OpenWrt.
SOC: MediaTek MT7986A
RAM: 2 GiB DDR4
eMMC: 8 GiB
Bluetooth: BLE5 (DA14531)
Serial: 3.3V level, 115200 8n1 on 4-pin connector
* SDG-8612 - Dual-band RJ-45 gateway
2x 2.5G MaxLinear PHY for WAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8614 - Dual-band SFP gateway
1x SFP cage with up to 2.5G speed
1x 2.5G MaxLinear PHY for LAN port
3x 1GE LAN ports via MT7531 switch
* SDG-8622 - Tri-band mesh router
2x 2.5G MaxLinear PHY
The MT7986 2G and 5G are used as 2G and 5G high band.
There’s a MT7915 PCIe card for 5G low band.
* SDG-8632 - Tri-band mesh router with 6 GHz
2x 2.5G MaxLinear PHY
The MT7986 serves the 2G and 6G bands.
There’s a MT7915 PCIe card for 5G.
Installation via U-Boot serial console:
0. setup TFTP server with IP 192.168.1.10/24, place initramfs image
renamed to openwrt.XXX where XXX is the internal product number:
SDG-8612: XXX = 412
SDG-8614: XXX = 414
SDG-8622: XXX = 422
SDG-8632: XXX = 432
1. connect to the serial console and power on the device.
Interrupt the bootloader by pressing 'st'
2. setenv boot_mode openwrt ; saveenv
3. run boot1
Load firmware via TFTP and write to flash
4. run boot2
Now OpenWrt initramfs should boot
5. upload sysupgrade.bin via scp to /tmp
6. sysupgrade
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Import driver for I2C-connected HolTek MCU controlling the RGBW LED
found in Adtran SmartRG devices.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add downstream DT property to setup the PHY LEDs of the MaxLinear
GPY211 PHY in such way that the VDD of the LED is driven by the SoC
pin rather than the GND (which is the default).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Similar to the *_get_mac_binary function, also split the common parts
off mtd_get_mac_ascii into new get_mac_ascii function and introduce
mmc_get_mac_ascii which uses it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The backported patch is broken, since kernel 6.1 has not
'include/linux/firmware' directory yet.
Fix the include to the correct path.
Fixes: #14115
Fixes: 52c365f055 ("kernel: backport v6.6 nvmem changes")
Signed-off-by: Andrey VOLKOV <andrey@volkov.fr>
[ improve commit description and title ]
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
The MAC address increment has been replaced by the new "mac-base"
NVMEM fixed layout. This old implementation can be removed now.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Add Generic subtarget definition. This is needed to keep consistent name
on every other target/subtarget and also to permit correct work of CI
workflows that expect a target/subtarget pattern.
Fixes: c16b2293fe ("ixp4xx: Resurrect IXP4xx support using device tree")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Refresh ramips patches which got out of sync due to backported changes
of the MediaTek Ethernet driver.
Fixes: 6407ef8d2b ("kernel: backport upstream mediatek WED changes")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
