In ar71xx we check for stuck DMA on devices which fall in the is_ar724x
SoC group (ar724x, ar933x, ar934x, qca9533, tp9343, qca955x, qca956x).
In ath79 we're currently performing this check only for devices with
ar7240 SoC, so this patch tries to sync the dma stuck checking behavior
with what is being done in ar71xx.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
It was reported, that latest ar71xx builds have broken networking on
TP-Link TL-WPA8630 and Nanostation M5 XW devices and that by reverting
the offending commit, everything is back to normal.
Fixes: d3506d1 ("ar71xx: ag71xx: fix compile error when enabling debug")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
CPU: AR9342 SoC
RAM: 64 MB DDR2
Flash: 8 MB NOR SPI
Ports: 100 MBit (24V PoE in)
WLAN: 2.4/5 GHz
UART: 1 UART on PCB marked as J1 with 115200 8N1 config
LEDs: Power, Ethernet, 4x RSSI LEDs (orange, red, 2x green)
Buttons: Reset
UART connection details
.---------------------------------.
| |
[ETH] J1 [ANT]
| o VCC o RX o TX o GND |
`---------------------------------'
Flashing instructions using recovery method over TFTP
1. Unplug the ethernet cable from the router.
2. Using paper clip press and hold the router's reset button. Make sure
you can feel it depressed by the paper clip. Do not release the button
until step 4.
3. While keeping the reset button pressed in, plug the ethernet cable
back into the AP. Keep the reset button depressed until you see the
device's LEDs flashing in upgrade mode (alternating LED1/LED3 and
LED2/LED4), this may take up to 25 seconds.
4. You may release the reset button, now the device should be in TFTP
transfer mode.
5. Set a static IP on your Computer's NIC. A static IP of 192.168.1.25/24
should work.
6. Plug the PoE injector's LAN cable directly to your computer.
7. Start tftp client and issue following commands:
tftp> binary
tftp> connect 192.168.1.20
tftp> put openwrt-ar71xx-generic-ubnt-bullet-m-xw-squashfs-factory.bin
Tested only on Bullet M2HP.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This is backport of the same functionality in ath79, from commit
d42a7c469 ("ath79: ubnt-m-xw: Fix factory image flashing using TFTP
recovery method")
Ubiquity allows flashing of unsigned factory images via TFTP recovery
method[1]. They claim in airOS v6.0.7 release changelog[2] following:
All future airOS versions will be signed in this way and not allow
unsigned firmware to be loaded except via TFTP.
U-boot bootloader on M-XW devices expects factory image revision
version in specific format. On airOS v6.1.7 with `U-Boot 1.1.4-s1039
(May 24 2017 - 15:58:18)` bootloader checks if the revision major(?)
number is actually a number, but in currently generated images there's
OpenWrt text and so the check fails:
Hit any key to stop autoboot: 0
Setting default IP 192.168.1.20
Starting TFTP server...
Receiving file from 192.168.1.25:38438
Received 4981148 bytes
Firmware check failed! (1)
By placing arbitrary correct number first in major version, we make the
bootloader happy and we can flash factory images over TFTP again:
Received 3801500 bytes
Firmware Version: XW.ar934x.v6.0.4-42.OpenWrt-r9766+2-be42e44
Setting U-Boot environment variables
Un-Protected 1 sectors
Erasing Flash.... done
Patch provided by AREDN[3] project, tested on Bullet M2 XW.
1. https://help.ubnt.com/hc/en-us/articles/204910124-UniFi-TFTP-Recovery-for-Bricked-Access-Points
2. https://dl.ubnt.com/firmwares/XW-fw/v6.0.7/changelog.txt
3. https://github.com/aredn
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This patch adds support for the following computer on modules (CoM) from
Toradex[A]:
Apalis iMX6 Quad 2GB IT - i.MX 6Quad 800MHz, 2GB DDR3, 4GB eMMC
-40° to +85° C Temp
Apalis iMX6 Quad 1GB - i.MX 6Quad 1GHz, 1GB DDR3, 4GB eMMC
0° to +70° C Temp
Apalis iMX6 Dual 1GB IT - i.MX 6Dual 800MHz, 1GB DDR3, 4GB eMMC
-40° to +85° C Temp
Apalis iMX6 Dual 512MB - i.MX 6Dual 1GHz, 512MB DDR3, 4GB eMMC
0° to +70° C Temp
I've developed and tested it on Quad 2GB IT v1.1A and Dual 512MB v1.1A
CoMs, using Ixora[B] carrier board v1.0A, but it should hopefuly work on
Eval[C] board as well.
A. https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-freescale-imx-6
B. https://www.toradex.com/products/carrier-board/ixora-carrier-board
C. https://www.toradex.com/products/carrier-board/apalis-evaluation-board
Flashing/recovery instructions:
1. Download and compile imx_loader for OpenWrt from
https://github.com/ynezz/imx_loader
2. Enter recovery mode as desribed in
https://developer.toradex.com/knowledge-base/imx-recovery-mode
3. Connect board via USB to the host computer, check that it's connected
by lsusb:
15a2:0054 Freescale Semiconductor, Inc. i.MX 6Dual/6Quad SystemOnChip
in RecoveryMode
4. Copy following OpenWrt images to imx_loader directory:
SPL
u-boot.img
u-boot-with-spl.imx
openwrt-imx6-apalis-recovery.scr
openwrt-imx6-apalis-squashfs.combined.bin
5. Run imx_usb in imx_loader directory
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fix dbclient regression in 2019.77. After exiting the terminal would be left
in a bad state. Reported by Ryan Woodsmall
drop patch applied upstream:
010-tty-modes-werent-reset-for-client.patch
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com>
This patch enable gnu99 mode for the nec-enc utility which
fixes the following build-breaking errors on some older
architectures.
nec-enc.c: In function ‘xor_data’:
nec-enc.c:34:2: error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode
for (int i = 0; i < len; i++) {
^~~
nec-enc.c:34:2: note: use option -std=c99, -std=gnu99, -std=c11 or -std=gnu11 to compile your code
nec-enc.c: In function ‘main’:
nec-enc.c:101:3: error: ‘for’ loop initial declarations are only allowed in C99 or C11 mode
for (int i = 0; i < n; i++) {
^~~
Spotted-By: Buildbot
Fixes: fac27643f0 ("firmware-utils: add nec-enc")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Add switch definition for the rtl8367b switch to the DTS/DTSi for
the Belkin F9K1109v1 that was mistakenly omitted from the initial
commit.
Fixes: 017ec068e3 (ramips: add support for Belkin F9K1109v1)
Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com>
nec-enc provides firmware encoding/decoding with model specific key
for NEC devices.
known devices:
- Aterm WF1200CR
- Aterm WG1200CR
- Aterm WG2600HS
usage:
nec-enc -i infile -o outfile -k key
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[checkpatch fixes, marked usage as noreturn, added static function,
moved buf* from stack to the global data segment]
Upstream driver has gone through a series of cleanup and was moved
from drivers/staging into drivers/spi. Backport it to replace our
messy driver.
Tested-by: Jörg Schüler-Maroldt <joerg-linux@arcor.de>
[LinkIt Smart 7688, AcSIP AI7688H Wi-Fi module]
Tested-by: Rosen Penev <rosenp@gmail.com>
Tested-by: Tian Xiao bo <peterwillcn@gmail.com>
[Newifi-D2 MediaTek MT7621 ver:1 eco:3]
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Otherwise tar will keep the sgid bit when running
from a sgid-set directory, resulting in a different
file being generated.
Signed-off-by: Eneas U de Queiroz <cote2004-github@yahoo.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
[reworked commit message, removed DMARC]
We do not need to define an empty Build/Configure since
the default checks for existing ./configure and does nothing
in case nothing is found.
Similar for Build/Compile: we can remove the definition
when we only call the default.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
I made a similar change to this here:
https://github.com/openwrt/packages/pull/8159
However, it turns out this did not fix the problem as the problem has to
do with tools/xz and not the xz package. The error is the same and causes
linking errors as can be seen above.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Currently, tplink-safeloader definition is only used a base for
another common definition.
This patch adjusts tplink-safeloader so it can be actually used
for some targets in generic-tp-link.mk.
This patch is cosmetic except for the order of
"check-size $$$$(IMAGE_SIZE)" and "append-metadata" exchanged
for the tplink_re350k-v1 .
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [dealed with
tplink_cpe210-v2 and tplink_cpe210-v3, removed tplink-safeloader-uimage's
extra IMAGE/sysupgrade.bin rule]
After getting rid of cryptsetup's heavy openssl dependency, there is now
the problem of missing RIPEMD160 support. RIPEMD160 is used for True/Vera
crypt volumes as well as old LUKS1 ones.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Enable the USB power for the Netgear R6120. Otherwise, no power is
supplied to an attached USB device.
Signed-off-by: David Bauer <mail@david-bauer.net>
With transition from ar71xx to ath79 some of devices change their naming
of LEDs. When upgrading from ar71xx target images this will require the
user to adjust previously working configuration. This commit adds
migration script which can be used to rename old names to new ones.
With this previously working configuration will be automatically
adjusted, wihtout user intervention.
This commit adds migration case for EnGenius EPG5000, the wireless LEDs
names have changed from epg5000:blue:wlan2-g and epg5000:blue:wlan-5g to
epg5000:blue:wlan2g and epg5000:blue:wlan5g.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Currently leds migration scripts in ar71xx and lantiq share a lot of
logic and introducing leds migration to another target would mean
copying this code, again. Therefore add common logic to library in
base-files package.
Suggested-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Hardware spec:
CPU: MTK MT7621A
RAM: 256MB
ROM: 16MB SPI Flash
WiFi: MT7603EN + MT7612EN
Button: 2 buttons (reset, wps)
LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB)
Ethernet: 3 ports, 2 LAN + 1 WAN
Other: USB3.0
Flashing instructions:
Visit the openwrt forum topic for this router:
https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692
to get the bootloader and unlock firmware.
0. upgrade your router with the telnet firmware via the
firmware upgrade page on the webui.
1. telnet 192.168.11.1 from your PC
2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer
it to the /tmp directory of the router.
3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader
4. turn off the power
5. Push the reset button while turning on the router and
wait until LED start blinking (~10sec.)
6. Connect Ethernet port and goto http://192.168.1.1.
7. Upload the firmware to firmware restore page in webui.
Signed-off-by: Zhao Yu <574249312@qq.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the
flashing instructions, fixed author]
* allowedips: initialize list head when removing intermediate nodes
Fix for an important regression in removing allowed IPs from the last
snapshot. We have new test cases to catch these in the future as well.
* tools: warn if an AllowedIP has a nonzero host part
If you try to run `wg set wg0 peer ... allowed-ips 192.168.1.82/24`, wg(8)
will now print a warning. Even though we mask this automatically down to
192.168.1.0/24, usually when people specify it like this, it's a mistake.
* wg-quick: add 'strip' subcommand
The new strip subcommand prints the config file to stdout after stripping
it of all wg-quick-specific options. This enables tricks such as:
`wg addconf $DEV <(wg-quick strip $DEV)`.
* tools: avoid unneccessary next_peer assignments in sort_peers()
Small C optimization the compiler was probably already doing.
* peerlookup: rename from hashtables
* allowedips: do not use __always_inline
* device: use skb accessor functions where possible
Suggested tweaks from Dave Miller.
* blake2s: simplify
* blake2s: remove outlen parameter from final
The blake2s implementation has been simplified, since we don't use any of the
fancy tree hashing parameters or the like. We also no longer separate the
output length at initialization time from the output length at finalization
time.
* global: the _bh variety of rcu helpers have been unified
* compat: nf_nat_core.h was removed upstream
* compat: backport skb_mark_not_on_list
The usual assortment of compat fixes for Linux 5.1.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
This commit adds support for Linux 4.19 kernel, various cleanups
listed below.
Drop 170-cisco-hack.patch as these devices never seems to have been
supported.
Unset kernel symbols:
* CONFIG_CAVIUM_CN63XXP1=y
No supported hardware uses CN63XXP1 and it causes "slight decrease in
performance"
Source: https://cateee.net/lkddb/web-lkddb/CAVIUM_CN63XXP1.html
* CONFIG_USB_OCTEON_EHCI=y
CONFIG_USB_OCTEON_OHCI=y
Deprecated
Source: https://cateee.net/lkddb/web-lkddb/USB_OCTEON_EHCI.htmlhttps://cateee.net/lkddb/web-lkddb/USB_OCTEON_OHCI.html
Removed kernel symbols:
* # CONFIG_ARCH_HIBERNATION_POSSIBLE=y
* CONFIG_ARCH_SUSPEND_POSSIBLE=y
These are not in if you do a vanilla config of a MIPS Octeon kernel
and I can't find any references about support on this platform.
* # CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
* CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
No need to have this in by default, not defined in most other targets
* CONFIG_CRASH_CORE=y
Can't find any documentation why this should be enabled by default
* CONFIG_DEBUG_INFO=y
Set by https://github.com/openwrt/openwrt/blob/master/config/Config-kernel.in#L134
* CONFIG_DEBUG_SPINLOCK=y
No need to have this in by default
* CONFIG_DEFAULT_HUNG_TASK_TIMEOUT=120
Already set by default
Source: https://cateee.net/lkddb/web-lkddb/DEFAULT_HUNG_TASK_TIMEOUT.html
* CONFIG_DETECT_HUNG_TASK=y
No need to have this in by default, not defined in most other targets
* CONFIG_HAVE_DEBUG_KMEMLEAK=y
No need to have this in by default, not defined in most other targets
* CONFIG_HAVE_DEBUG_STACKOVERFLOW=y
No need to have this in by default
* CONFIG_HAVE_IDE=y
None of the supported devices have IDE
* CONFIG_HZ=250
* # CONFIG_HZ_100 is not set
* CONFIG_HZ_250=y
This is broken with generic config
* CONFIG_KALLSYMS=y
No need to have this in by default, not defined in most other targets
* CONFIG_KEXEC=y
* CONFIG_KEXEC_CORE=y
No need to have this in by default, not defined in most other targets
* CONFIG_HAVE_KVM=y
No need to have this in by default
* CONFIG_SCHED_DEBUG=y
No need to have this in by default, not defined in most other targets
* CONFIG_SYSFS_DEPRECATED=y
Deprecated symbol
Source: https://cateee.net/lkddb/web-lkddb/SYSFS_DEPRECATED.html
* CONFIG_SYSFS_DEPRECATED_V2=y
Discouraged usage in general
Source: https://cateee.net/lkddb/web-lkddb/SYSFS_DEPRECATED_V2.html
* CONFIG_UNINLINE_SPIN_UNLOCK=y
No need to have this in by default, not defined in most other targets
Source: https://github.com/openSUSE/kernel/blob/master/lib/Kconfig.debug#L1137
* CONFIG_ZLIB_INFLATE=y
No need to have this in by default, not defined in most other targets
Signed-off-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
Currently sysupgrade overwrites whole disk and destroys partitions added
by user. Sync the sysupgrade code with the one present in x86 target to
remedy this behaviour.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Since some boards could be also booted from other mediums than SD card,
lets make the upgrade block device autodetected.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Since most of devices using SD card image to boot, use ext4 as boot
files system we can drop fat fs related packages. Also move packages
which are added repeatedly across subtargets to their default packages,
with droping the ones that are enabled in target kernel configugation.
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
This will allow to drop additional packages and shrink image size.
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
The options are managed on a generic way by the can
kmod packages
Additionally, select can packages only for devices that
currently has CAN enabled, which is only the ZC702
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The options are managed on a generic way by video packages
Additionally, only one of the currently supported boards
has a camera interface, but it requires programming
the FPGA fabric first
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The options are managed on a generic way by the sound
kmod packages
Additionally, none of the currently supported boards have
sound support out of the box, as they require programming
the FPGA fabric first
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The removed patches are now integrated in the upstream kernel.
Refresh all patches on top of the new backports release.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net>
